ALUMINUM ELECTROLYTIC CAPACITORS UJ Chip Type, Higher Capacitance Range series Chip Type, higher capacitance in larger case sizes (φ12.5,φ16,φ18,φ20) Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape and tray. UN UJ Bi-Polarized High Reliability UH Specifications Item Performance Characteristics Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance — 55 ~ +105˚C (6.3 ~ 100V),— 40 + ~ 105˚C (160 ~ 450V) 6.3 ~ 450V 3.3 ~ 6800µF ±20% at 120Hz, 20˚C Rated voltage(V) Leakage Current — tan δ 6.3 ~ 100 160 ~ 450 After 1 minutes' application of rated voltage, leakage current is not more than 0.03CV or 4(µA), whichever is greater. I =0.04CV+100 ( µA)max.(1 minute's) 160 ~ 250 400 • 450 120Hz Rated voltage(V) 6.3 10 16 25 35 50 63 100 tan δ (MAX) 0.26 0.22 0.18 0.16 0.14 0.12 0.10 0.08 0.15 0.20 20˚C 120Hz For capacitance of more than 1000µF, add 0.02 for every increase of 1000µF. 6.3 10 16 25 35 50 63 100 160 ~ 250 400 • 450 Z — 25˚C/Z+20˚C 5 4 3 2 2 2 2 2 3 6 Z — 40˚C/Z+20˚C 10 8 6 4 3 3 3 3 6 10 Rated voltage(V) Stability at Low Temperature Impedance ratio ZT/Z20(MAX.) characteristics requirements listed at right. Initial specified value or less Within ±20% of initial value 200% or less of initial specified value After leaving capacitors under no load at 105˚C for 1000 hours, they meet the specified Shelf Life value for endurance characteristics listed above. Black print on the case top. Marking Chip Type Type numbering system (Example : 50V 330µF) B±0.2 Plastic platform A±0.2 Voltage Trade mark Leakage current Capacitance change tan δ After 5000 hours' application of rated voltage at 105˚C, capacitors meet the Endurance Lot No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 U U J 1 H 3 3 1 M NR 1 Capacitance Pressure relief vent C±0.2 E L±0.5 Capacitance Tolerance (±20%) H±0.1 φD 12.5 16. 18. 20. 4.0 4.5 5.0 5.0 A B 13.6 17.1 19.1 21.1 C 16.0 19.5 21.5 23.5 8.0 10.5 11.5 13.5 E H 2.5 3.75 3.75 3.75 Dimensions V (µF) Cap. Code 221 331 471 102 222 332 472 682 220 330 470 1000 2200 3300 4700 6800 V (µF) Cap. Code 3.3 4.7 10 22 33 47 68 100 220 330 470 3R3 4R7 100 220 330 470 680 101 221 331 471 6.3 0J 12.5 × 13.5 16 × 16.5 18 × 16.5 18 × 21.5 20 × 21.5 10 1A 63 1J 12.5 × 13.5 12.5 × 16.0 16 × 16.5 18 × 16.5 18 × 21.5 500 810 1000 1200 1450 100 2A 175 225 385 490 590 12.5 × 13.5 12.5 × 16.0 16 × 16.5 18 × 16.5 20 × 21.5 Rated Capacitance(330µF) Rated voltage(50V) Code NR 20 RR D × L (mm) 12.5 × 13.5 16 × 16.5 18 × 16.5 18 × 21.5 12.5 × 13.5 16 × 16.5 18 × 16.5 16 × 21.5 φD 12.5 ~ 18 Type 25 1E 12.5 × 13.5 12.5 × 16.0 18 × 16.5 18 × 21.5 360 630 930 1150 160 2C 160 205 285 440 500 ZD Series name 16 1C 12.5 × 16.0 16 × 16.5 18 × 16.5 18 × 21.5 20 × 21.5 440 750 930 1100 1350 MS Tray Configuration A±0.2 Series B±0.2 φ D±0.5 nichicon 330 µF UJ 50V H9736 Package code Taping 200 2D 95 260 320 380 12.5 × 13.5 12.5 × 16.0 16 × 16.5 18 × 16.5 18 × 21.5 20 × 21.5 35 1V 320 400 700 1050 12.5 × 13.5 12.5 × 16.0 16 × 16.5 18 × 16.5 20 × 21.5 250 2E 80 105 220 270 330 410 12.5 × 13.5 12.5 × 16.0 16 × 16.5 18 × 16.5 18 × 21.5 20 × 21.5 Size φ12.5 × 21 is available for capacitors marked," ". Size φ16 × 21.5L is available for capacitors marked," ". Size φ20 × 16.5L is available for capacitors marks," In this case, 6 will be put at 12th digit of type numbering system, “ ” ". 50 1H 12.5 × 16.0 16 × 16.5 18 × 16.5 18 × 21.5 280 360 490 750 1150 400 2G 65 105 180 230 280 340 12.5 × 16.0 16 × 16.5 18 × 21.5 20 × 21.5 320 440 550 820 450 2W 50 85 130 160 12.5 × 13.5 12.5 × 16.0 16 × 16.5 18 × 21.5 20 × 21.5 40 50 85 130 160 Case size Rated Ripple Rated Ripple (mA rms) at 105˚C 120Hz Frequency coefficient of rated ripple current V 6.3 ~ 100 160 ~ 450 Cap.(µF) Frequency 00 ~ 68 0100 ~ 4700 1000 ~ 6800 3.3 ~ 100 50Hz 0.75 0.80 0.85 0.80 120Hz 1.00 1.00 1.00 1.00 300Hz 1.35 1.23 1.10 1.25 1kHz 1.57 1.34 1.13 1.40 10kHz ~ 2.00 1.50 1.15 1.60 Taping Specifications are given in page 21. Please refer to page 3 for the minimum order quantity. CAT.8100P