ETC AK006M2-93

GaAs IC SPDT Switch With Integral Driver
Non-Reflective DC–6 GHz
AK006M2-93
Features
■ Integral Driver ±5 V Supply Voltages
-93
0.160
0.140
■ High Isolation, Non-Reflective
■ Broadband DC–6 GHz
0.100
■ Small Low Cost “Chip on Board” Package
0.060
Description
0.020
0.000
0.140
0.056
0.000
The AK006M2-93 is an IC FET SPDT switch in a low cost
“chip on board” package. It features non-reflective
matching at each output, broadband performance, with
integral driver. This switch can be used in many analog
and digital wireless communication systems.
Top View
Electrical Specifications at 25°C
Parameter1
Insertion
Frequency6
Loss2
DC–1.0
DC–2.0
DC–4.0
DC–6.0
GHz
GHz
GHz
GHz
Isolation
DC–1.0
DC–2.0
DC–4.0
DC–6.0
GHz
GHz
GHz
GHz
VSWR (I/O)
DC–1.0
DC–2.0
DC–4.0
DC–6.0
GHz
GHz
GHz
GHz
Min.
48
42
36
26
Typ.
Max.
Unit
0.7
1.0
1.4
1.8
0.8
1.2
1.6
2.0
dB
dB
dB
dB
52
48
37
30
dB
dB
dB
dB
1.3:1
1.4:1
1.6:1
1.8:1
1.4:1
1.6:1
1.8:1
2.0:1
Typ.
Max.
Unit
10
20
30
20
40
40
ns
ns
mV
Operating Characteristics at 25°C
Parameter
Switching Characteristics
Condition
Frequency
Min.
Rise, Fall (10/90% or 90/10% RF)
On, Off (50% CTL to 90/10% RF)
Video Feedthru3
Input Power for 1 dB Compression
Intermodulation Intercept Point (IP3)
For Two-tone Input Power 13 dBm
Control Voltages
VLow
VHigh
Supply Voltages4,5
+5 V @ 1 mA Typ.
-5 V @ 4 mA Typ.
1. All measurements made in a 50 Ω system, unless otherwise specified.
2. Insertion loss changes by 0.003 dB/°C.
3. Video feedthru measured with 1 ns risetime pulse and 500 MHz bandwidth.
4. The supply voltage and ground must be connected before TTL voltage is
applied. To avoid voltage sequencing refer to the Application Note section,
“Driver Protection Circuit.”
0.5–6 GHz
0.001 GHz
20
12
23
15
dBm
dBm
0.5–6 GHz
0.001 GHz
34
22
37
26
dBm
dBm
0
4
0.5
5.5
V
V
+4.75
-4.75
+5.25
-5.25
V
V
5. Current increases from 4 mA to 5 mA @ 85°C.
6. DC = 300 kHz.
Alpha Industries, Inc. [781] 935-5150 • Fax [617] 824-4579 • Email sales@alphaind.com • www.alphaind.com
Specifications subject to change without notice. 2/00A
Powered by ICminer.com Electronic-Library Service CopyRight 2003
1
GaAs IC SPDT Switch With Integral Driver Non-Reflective DC–6 GHz
AK006M2-93
Typical Performance Data
70
60
2.0
Isolation (dB)
Insertion Loss (dB)
2.5
1.5
1.0
50
40
30
20
0.5
10
0.0
0
1
2
3
4
5
0
6
0
1
2
3
4
5
Frequency (GHz)
Frequency (GHz)
Insertion Loss vs. Frequency
Isolation vs. Frequency
Truth Table
6
Absolute Maximum Ratings
VCTRL
J1–J2
J1–J3
1
Insertion Loss
Isolation
0
Isolation
Insertion Loss
Characteristic
Value
RF Input Power (RF In)
0.5 W > 500 MHz
0.1 W @ 50 MHz
Bias Voltage (VB)
+7.0 V, -7.0 V
Control Voltage (VC)
Pin Out
+5 V
J1
J2
50
VCTRL
-5 V
-40°C to +90°C
Storage Temperature (TST)
-65°C to +150°C
Thermal Resistance (ΘJC)
30°C/W
GND
-93
GND
50
-0.2 V, +7.0 V
Operating Temperature (TOP)
0.160
0.150
J3
0.140
0.130
0.112
0.110
0.090
0.070
0.050
0.048
0.030
0.020
Glass
0.140
0.121
0.102
0.038
0.020
0.000
0.010
0.000
Pt/Pd/Au
Bottom View
The “chip on board” package is a ceramic leadless chip carrier with a ceramic
lid, which allows for automatic pick and place. The external terminals and
backside ground plane are Pt/Pd/Au, which is highly leach resistant and very
tolerant to variations in solder conditions. The glass fingers between contacts
prevent the possibility of shorted terminals. The recommended solder
attachment is a SN6337 (Pb/SN).
2
Alpha Industries, Inc. [781] 935-5150 • Fax [617] 824-4579 • Email sales@alphaind.com • www.alphaind.com
Specifications subject to change without notice. 2/00A
Powered by ICminer.com Electronic-Library Service CopyRight 2003