AD ADP3630ARMZ-R7

High Speed, Dual, 2 A MOSFET Driver
ADP3629/ADP3630/ADP3631
FEATURES
GENERAL DESCRIPTION
Industry-standard-compatible pinout
High current drive capability
Precise threshold shutdown comparator
UVLO with hysteresis
Overtemperature warning signal
Overtemperature shutdown
3.3 V-compatible inputs
Rise time and fall time: 10 ns typical at 2.2 nF load
Fast propagation delay
Matched propagation delays between channels
Supply voltage: 9.5 V to 18 V
Dual outputs can be operated in parallel
(ADP3629/ADP3630)
Rated from −40°C to +85°C ambient temperature
8-lead SOIC_N and 8-lead MSOP
The ADP3629/ADP3630/ADP3631 are dual, high current, high
speed drivers, capable of driving two independent N-channel
power MOSFETs. The ADP3629/ADP3630/ADP3631 use the
industry-standard footprint but add high speed switching performance and improved system reliability.
APPLICATIONS
The wide input voltage range allows the driver to be compatible
with both analog and digital PWM controllers.
The ADP3629/ADP3630/ADP3631 have an internal temperature
sensor and provide two levels of overtemperature protection: an
overtemperature warning and an overtemperature shutdown at
extreme junction temperatures.
The SD function, generated from a precise internal comparator,
provides fast system enable or shutdown. This feature allows
redundant overvoltage protection, complementing the protection inside the main controller device, or provides safe system
shutdown in the event of an overtemperature warning.
AC-to-DC switch mode power supplies
DC-to-DC power supplies
Synchronous rectification
Motor drives
Digital power controllers are supplied from a low voltage supply,
and the driver is supplied from a higher voltage supply. The
ADP3629/ADP3630/ADP3631 add UVLO and hysteresis functions, allowing safe startup and shutdown of the higher voltage
supply when used with low voltage digital controllers.
FUNCTIONAL BLOCK DIAGRAM
VDD
ADP3629/ADP3630/ADP3631
8
SD 1
OTW
OVERTEMPERATURE
PROTECTION
VDD
VEN
NONINVERTING
INA, 2
INA
7 OUTA
INVERTING
PGND 3
UVLO
6 VDD
NONINVERTING
INB, 4
INB
08401-101
5 OUTB
INVERTING
Figure 1.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2009 Analog Devices, Inc. All rights reserved.
ADP3629/ADP3630/ADP3631
TABLE OF CONTENTS
Features .............................................................................................. 1 Test Circuit ...................................................................................... 10 Applications ....................................................................................... 1 Theory of Operation ...................................................................... 11 General Description ......................................................................... 1 Input Drive Requirements (INA, INA, INB, INB, and SD) .. 11 Functional Block Diagram .............................................................. 1 Low-Side Drivers (OUTA, OUTB) .......................................... 11 Revision History ............................................................................... 2 Shutdown (SD) Function .......................................................... 11 Specifications..................................................................................... 3 Overtemperature Protections ................................................... 12 Timing Diagrams.......................................................................... 4 Supply Capacitor Selection ....................................................... 12 Absolute Maximum Ratings............................................................ 6 PCB Layout Considerations ...................................................... 12 Thermal Resistance ...................................................................... 6 Parallel Operation ...................................................................... 12 ESD Caution .................................................................................. 6 Thermal Considerations............................................................ 13 Pin Configurations and Function Descriptions ........................... 7 Outline Dimensions ....................................................................... 14 Typical Performance Characteristics ............................................. 8 Ordering Guide .......................................................................... 14 REVISION HISTORY
9/09—Revision 0: Initial Version
Rev. 0 | Page 2 of 16
ADP3629/ADP3630/ADP3631
SPECIFICATIONS
VDD = 12 V, TJ = −40°C to +125°C, unless otherwise noted. 1
Table 1.
Parameter
SUPPLY
Supply Voltage Range
Supply Current
Symbol
Standby Current
UVLO
Turn-On Threshold Voltage
Turn-Off Threshold Voltage
Hysteresis
DIGITAL INPUTS (INA, INA, INB, INB, SD)
Input Voltage High
Input Voltage Low
Input Current
SD Threshold High
ISBY
No switching, INA, INA, INB, and INB
disabled
SD = 5 V
VUVLO_ON
VUVLO_OFF
VDD rising, TA = 25°C
VDD falling, TA = 25°C
SD Threshold Low
SD Hysteresis
Internal Pull-Up/Pull-Down Current
OUTPUTS (OUTA, OUTB)
Output Resistance, Unbiased
Peak Source Current
Peak Sink Current
SWITCHING TIME
OUTA, OUTB Rise Time
OUTA, OUTB Fall Time
OUTA, OUTB Rising Propagation Delay
OUTA, OUTB Falling Propagation Delay
SD Propagation Delay Low
SD Propagation Delay High
Delay Matching Between Channels
OVERTEMPERATURE PROTECTION
Overtemperature Warning Threshold
Overtemperature Shutdown Threshold
Temperature Hysteresis for Shutdown
Temperature Hysteresis for Warning
Overtemperature Warning Low
1
VDD
IDD
VIH
VIL
IIN
VSD_H
VSD_L
VSD_HYST
Test Conditions/Comments
Min
Typ
Max
Unit
1.2
18
3
V
mA
1.2
3
mA
8.7
7.7
1.0
9.5
8.5
V
V
V
9.5
8.0
7.0
2.0
0 V < VIN < VDD
TA = 25°C
TA = 25°C
TA = 25°C
−20
1.19
1.21
0.95
240
1.28
1.28
1.0
280
6
0.8
+20
1.38
1.35
1.05
320
V
V
μA
V
V
V
mV
μA
VDD = PGND
See Figure 20
See Figure 20
80
2
−2
tRISE
tFALL
tD1
tD2
tdL_SD
tdH_SD
CLOAD = 2.2 nF, see Figure 3 and Figure 4
CLOAD = 2.2 nF, see Figure 3 and Figure 4
CLOAD = 2.2 nF, see Figure 3 and Figure 4
CLOAD = 2.2 nF, see Figure 3 and Figure 4
See Figure 2
See Figure 2
10
10
14
22
32
48
2
25
25
30
35
45
75
ns
ns
ns
ns
ns
ns
ns
TW
TSD
THYS_SD
THYS_W
VOTW_OL
See Figure 6
See Figure 6
See Figure 6
See Figure 6
Open drain, −500 μA
135
165
30
10
150
180
°C
°C
°C
°C
V
120
150
All limits at temperature extremes guaranteed via correlation using standard statistical quality control (SQC) methods.
Rev. 0 | Page 3 of 16
kΩ
A
A
0.4
ADP3629/ADP3630/ADP3631
TIMING DIAGRAMS
SD
tdL_SD
tdH_SD
OUTA,
OUTB
08401-002
90%
10%
Figure 2. Shutdown Timing Diagram
VIH
INA,
INB
VIL
tD1
tRISE
tD2
90%
90%
OUTA,
OUTB
tFALL
10%
08401-003
10%
Figure 3. Output Timing Diagram (Noninverting)
VIL
INA,
INB
VIH
tD1
tRISE
tD2
90%
90%
OUTA,
OUTB
tFALL
10%
08401-103
10%
Figure 4. Output Timing Diagram (Inverting)
VUVLO_ON
VUVLO_OFF
UVLO MODE
NORMAL OPERATION
OUTPUTS DISABLED
UVLO MODE
OUTPUTS DISABLED
Figure 5. UVLO Function
Rev. 0 | Page 4 of 16
08401-005
VDD
ADP3629/ADP3630/ADP3631
TSD
TSD – THYS_SD
TW
TW – THYS_W
TJ
OT WARNING
OT SHUTDOWN
OT WARNING
OUTPUTS
ENABLED
OUTPUTS
DISABLED
OUTPUTS
ENABLED
NORMAL OPERATION
08401-006
NORMAL OPERATION
OTW
Figure 6. Overtemperature Warning and Shutdown
Rev. 0 | Page 5 of 16
ADP3629/ADP3630/ADP3631
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 2.
Parameter
VDD
OUTA, OUTB
DC
<200 ns
INA, INA, INB, INB, SD
ESD
Human Body Model (HBM)
Field Induced Charged Device
Model (FICDM)
SOIC_N
MSOP
Junction Temperature Range
Storage Temperature Range
Lead Temperature
Soldering (10 sec)
Vapor Phase (60 sec)
Infrared (15 sec)
θJA is specified for a device soldered in a 4-layer circuit board
and is measured per JEDEC standards JESD51-2, JESD51-5,
and JESD51-7.
Rating
−0.3 V to +20 V
−0.3 V to VDD + 0.3 V
−2 V to VDD + 0.3 V
−0.3 V to VDD + 0.3 V
Table 3. Thermal Resistance
Package Type
8-Lead SOIC_N
8-Lead MSOP
3.5 kV
1.5 kV
1.0 kV
−40°C to +150°C
−65°C to +150°C
ESD CAUTION
300°C
215°C
260°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. 0 | Page 6 of 16
θJA
110.6
162.2
Unit
°C/W
°C/W
ADP3629/ADP3630/ADP3631
SD 1
INA 2
ADP3629
8
OTW
7
OUTA
PGND 3
6 VDD
TOP VIEW
INB 4 (Not to Scale) 5 OUTB
08401-008
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
Figure 7. ADP3629 Pin Configuration
Table 4. ADP3629 Pin Function Descriptions
Mnemonic
SD
INA
PGND
INB
OUTB
VDD
OUTA
OTW
Description
Output Shutdown. When high, this pin disables normal operation, forcing OUTA and OUTB low.
Inverting Input Pin for Channel A Gate Driver.
Ground. This pin should be closely connected to the source of the power MOSFET.
Inverting Input Pin for Channel B Gate Driver.
Output Pin for Channel B Gate Driver.
Power Supply Voltage. Bypass this pin to PGND with a 1 μF to 5 μF ceramic capacitor.
Output Pin for Channel A Gate Driver.
Overtemperature Warning Flag. Open drain, active low.
SD 1
INA 2
ADP3630
8
OTW
7
OUTA
PGND 3
6 VDD
TOP VIEW
INB 4 (Not to Scale) 5 OUTB
08401-001
Pin No.
1
2
3
4
5
6
7
8
Figure 8. ADP3630 Pin Configuration
Table 5. ADP3630 Pin Function Descriptions
Mnemonic
SD
INA
PGND
INB
OUTB
VDD
OUTA
OTW
Description
Output Shutdown. When high, this pin disables normal operation, forcing OUTA and OUTB low.
Input Pin for Channel A Gate Driver.
Ground. This pin should be closely connected to the source of the power MOSFET.
Input Pin for Channel B Gate Driver.
Output Pin for Channel B Gate Driver.
Power Supply Voltage. Bypass this pin to PGND with a 1 μF to 5 μF ceramic capacitor.
Output Pin for Channel A Gate Driver.
Overtemperature Warning Flag. Open drain, active low.
SD 1
INA 2
ADP3631
8
OTW
7
OUTA
PGND 3
6 VDD
TOP VIEW
INB 4 (Not to Scale) 5 OUTB
08401-009
Pin No.
1
2
3
4
5
6
7
8
Figure 9. ADP3631 Pin Configuration
Table 6. ADP3631 Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
Mnemonic
SD
INA
PGND
INB
OUTB
VDD
OUTA
OTW
Description
Output Shutdown. When high, this pin disables normal operation, forcing OUTA and OUTB low.
Inverting Input Pin for Channel A Gate Driver.
Ground. This pin should be closely connected to the source of the power MOSFET.
Input Pin for Channel B Gate Driver.
Output Pin for Channel B Gate Driver.
Power Supply Voltage. Bypass this pin to PGND with a 1 μF to 5 μF ceramic capacitor.
Output Pin for Channel A Gate Driver.
Overtemperature Warning Flag. Open drain, active low.
Rev. 0 | Page 7 of 16
ADP3629/ADP3630/ADP3631
TYPICAL PERFORMANCE CHARACTERISTICS
25
9
V UVLO_ON
8
20
V UVLO_OFF
TIME (ns)
UVLO (V)
7
6
15
tFALL
10
tRISE
5
5
–30
–10
10
30
50
70
TEMPERATURE (°C)
90
110
130
0
08401-022
3
–50
0
5
Figure 10. UVLO vs. Temperature
10
VDD (V)
15
20
08401-012
4
Figure 13. Rise and Fall Times vs. VDD
14
70
12
60
tFALL
10
tdH_SD
50
TIME (ns)
TIME (ns)
tRISE
8
6
40
tdL_SD
30
tD2
4
20
2
10
–30
–10
10
30
50
70
TEMPERATURE (°C)
90
110
130
0
08401-010
0
5
Figure 11. Rise and Fall Times vs. Temperature
20
1400
VDD = 12V
tdH_SD
SHUTDOWN THRESHOLD (mV)
40
tdL_SD
30
tD2
20
VSD_H
1200
50
tD1
10
1000
VSD_L
800
600
400
VSD_HYST
200
–30
–10
10
30
50
70
TEMPERATURE (°C)
90
110
130
0
–50
08401-011
TIME (ns)
15
Figure 14. Propagation Delay vs. VDD
60
0
–50
10
VDD (V)
Figure 12. Propagation Delay vs. Temperature
–30
–10
10
30
50
70
TEMPERATURE (°C)
90
110
Figure 15. Shutdown Threshold vs. Temperature
Rev. 0 | Page 8 of 16
130
08401-014
0
–50
08401-013
tD1
ADP3629/ADP3630/ADP3631
OUTA/OUTB
OUTA/OUTB
2
2
VDD = 12V
TIME = 20ns/DIV
1
08401-023
VDD = 12V
TIME = 20ns/DIV
1
INA/INB
Figure 16. Typical Rising Propagation Delay (Noninverting)
Figure 18. Typical Rise Time (Noninverting)
OUTA/OUTB
OUTA/OUTB
2
2
INA/INB
INA/INB
1
Figure 17. Typical Falling Propagation Delay (Noninverting)
VDD = 12V
TIME = 20ns/DIV
Figure 19. Typical Fall Time (Noninverting)
Rev. 0 | Page 9 of 16
08401-026
VDD = 12V
TIME = 20ns/DIV
08401-024
1
08401-025
INA/INB
ADP3629/ADP3630/ADP3631
TEST CIRCUIT
ADP3629/ADP3630/ADP3631
1 SD
2
OTW 8
INA,
INA
A
OUTA
7
INVERTING
VDD
3 PGND
NONINVERTING
VDD 6
4.7µF
CERAMIC
100nF
CERAMIC
CLOAD
B
INB,
INB
OUTB
5
INVERTING
08401-007
4
SCOPE
PROBE
NONINVERTING
Figure 20. Test Circuit
Rev. 0 | Page 10 of 16
ADP3629/ADP3630/ADP3631
THEORY OF OPERATION
The ADP3629/ADP3630/ADP3631 family of dual drivers is
optimized for driving two independent enhancement N-channel
MOSFETs or insulated gate bipolar transistors (IGBTs) in high
switching frequency applications.
LOW-SIDE DRIVERS (OUTA, OUTB)
These applications require high speed, fast rise and fall times, and
short propagation delays. The capacitive nature of MOSFETs and
IGBTs requires high peak current capability, as well.
When the ADP3629/ADP3630/ADP3631 are disabled, both
low-side gates are held low. An internal impedance is present
between the OUTA/OUTB pins and GND, even when VDD is
not present; this feature ensures that the power MOSFET is
normally off when bias voltage is not present.
ADP3629/ADP3630/ADP3631
2
OTW 8
VDS
NONINVERTING
INA,
INA
When interfacing the ADP3629/ADP3630/ADP3631 to external MOSFETs, the designer should consider ways to create a
robust design that minimizes stresses on both the driver and
the MOSFETs. These stresses include exceeding the short time
duration voltage ratings on the OUTA and OUTB pins, as well
as on the external MOSFET.
A
OUTA
7
INVERTING
VDD
3 PGND
NONINVERTING
VDD 6
VDS
4
B
INB,
INB
OUTB
Power MOSFETs are usually selected to have low on resistance to
minimize conduction losses, which usually implies a large input
gate capacitance and gate charge.
5
08401-017
INVERTING
Figure 21. Typical Application Circuit
INPUT DRIVE REQUIREMENTS (INA, INA, INB, INB,
AND SD)
The inputs of the ADP3629/ADP3630/ADP3631 are designed
to meet the requirements of modern digital power controllers;
the signals are compatible with 3.3 V logic levels. At the same
time, the input structure allows for input voltages as high as VDD.
The signals applied to the inputs (INA, INA, INB, and INB)
should have steep and clean fronts. It is not recommended that
slow changing signals be applied to drive these inputs because
such signals can result in multiple switching output signals
when the thresholds are crossed, causing damage to the power
MOSFET or IGBT.
SHUTDOWN (SD) FUNCTION
The ADP3629/ADP3630/ADP3631 feature an advanced shutdown function with accurate thresholds and hysteresis.
The SD signal is an active high signal. An internal pull-up is
present on this pin and, therefore, it is necessary to pull down
the pin externally for the drivers to operate normally.
In some power systems, it is sometimes necessary to provide an
additional overvoltage protection (OVP) or overcurrent protection
(OCP) shutdown signal to turn off the power devices (MOSFETs
or IGBTs) in case of failure of the main controller.
An accurate internal reference is used for the SD comparator so
that it can be used to detect OVP or OCP fault conditions.
+
DC
OUTPUT
An internal pull-down resistor is present at the input, which
guarantees that the power device is off in the event that the
input is left floating.
AC
INPUT
The SD input has a precision comparator with hysteresis and is
therefore suitable for slow changing signals (such as a scaleddown output voltage); see the Shutdown (SD) Function section
for more information about this comparator.
–
OUTA
PGND
SD
VEN
ADP3629/ADP3630/ADP3631
Figure 22. Shutdown Function Used for Redundant OVP
Rev. 0 | Page 11 of 16
08401-018
1 SD
The ADP3629/ADP3630/ADP3631 family of dual drivers is
designed to drive ground referenced N-channel MOSFETs. The
bias is internally connected to the VDD supply and to PGND.
ADP3629/ADP3630/ADP3631
OVERTEMPERATURE PROTECTIONS
PCB LAYOUT CONSIDERATIONS
The ADP3629/ADP3630/ADP3631 provide two levels of overtemperature protection:
Use the following general guidelines when designing printed
circuit boards (PCBs) for the ADP3629/ADP3630/ADP3631:
•
•
•
Overtemperature warning (OTW)
Overtemperature shutdown
The overtemperature warning is an open-drain logic signal and
is active low. In normal operation, when no thermal warning is
present, the signal is high, whereas when the warning threshold
is crossed, the signal is pulled low.
3.3V
VDD
•
•
•
•
OTW
Trace out the high current paths and use short, wide
(>40 mil) traces to make these connections.
Minimize trace inductance between the OUTA and OUTB
outputs and the MOSFET gates.
Connect the PGND pin as close as possible to the source of
the MOSFETs.
Place the VDD bypass capacitor as close as possible to the
VDD and PGND pins.
When possible, use vias to other layers to maximize thermal
conduction away from the IC.
Figure 24 shows an example of the typical layout based on the
preceding guidelines.
FLAGIN
ADP3629/ADP3630/ADP3631
ADP1043
PGND
VDD
ADP3629/ADP3630/ADP3631
PGND
08401-019
OTW
08401-027
Figure 23. OTW Signaling Scheme Example
The OTW open-drain configuration allows the connection
of multiple devices to the same warning bus in a wire-OR’ed
configuration, as shown in Figure 23.
PARALLEL OPERATION
The overtemperature shutdown turns off the device to protect it
in the event that the die temperature exceeds the absolute maximum limit of 150°C (see Table 2).
The two driver channels in the ADP3629 and ADP3630 devices
can be combined to operate in parallel to increase drive capability
and minimize power dissipation in the driver.
SUPPLY CAPACITOR SELECTION
The connection scheme for the ADP3630 is shown in Figure 25.
In this configuration, INA and INB are connected together, and
OUTA and OUTB are connected together.
Figure 24. External Component Placement Example
An improper decoupling can dramatically increase the rise times,
cause excessive resonance on the OUTA and OUTB pins, and, in
some extreme cases, even damage the device due to inductive
overvoltage on the VDD or OUTA/OUTB pins.
Particular attention must be paid to the layout in this case to
optimize load sharing between the two drivers.
The minimum capacitance required is determined by the size of
the gate capacitances being driven, but as a general rule, a 4.7 μF,
low ESR capacitor should be used. Multilayer ceramic chip
(MLCC) capacitors provide the best combination of low ESR
and small size. To further reduce noise, use a smaller ceramic
capacitor (100 nF) with a better high frequency characteristic
in parallel with the main capacitor.
Place the ceramic capacitor as close as possible to the ADP3629/
ADP3630/ADP3631 device and minimize the length of the
traces going from the capacitor to the power pins of the device.
Rev. 0 | Page 12 of 16
OTW 8
1 SD
ADP3630
2
INA
A
OUTA
7
VDD
3 PGND
VDD 6
VDS
4
INB
B
OUTB
5
08401-021
A local bypass capacitor for the supply input (VDD) of the
ADP3629/ADP3630/ADP3631 is recommended to reduce the
noise and to supply some of the peak currents that are drawn.
Figure 25. Parallel Operation
ADP3629/ADP3630/ADP3631
THERMAL CONSIDERATIONS
When designing a power MOSFET gate drive, the maximum
power dissipation in the driver must be considered to avoid
exceeding the maximum junction temperature.
In addition to the gate charge losses, there are also dc bias losses
(PDC) due to the bias current of the driver. This current is present
regardless of the switching frequency.
Data on package thermal resistance is provided in Table 3 to
help the designer in this task.
Several equally important aspects must also be considered.
•
•
•
•
•
•
In all practical applications where the external resistor is in the
order of a few ohms, the contribution of the external resistor
can be ignored, and the extra loss is assumed to be in the driver,
providing a good guard band for the power loss calculations.
PDC = VDD × IDD
Gate charge of the power MOSFET being driven
Bias voltage value used to power the driver
Maximum switching frequency of operation
Value of external gate resistance
Maximum ambient (and PCB) temperature
Type of package
The total estimated loss is the sum of PDC and PGATE.
PLOSS = PDC + (n × PGATE)
where n is the number of gates driven.
When the total power loss is calculated, the temperature
increase can be calculated as follows:
All of these factors influence and limit the maximum allowable
power dissipated in the driver.
The gate of a power MOSFET has a nonlinear capacitance
characteristic. For this reason, although the input capacitance
is usually reported in the MOSFET data sheet as CISS, it is not
useful to calculate power losses.
The total gate charge necessary to turn on a power MOSFET
device is usually reported on the device data sheet under QG.
This parameter varies from a few nanocoulombs (nC) to several
hundreds of nC and is specified at a specific VGS value (10 V
or 4.5 V).
The power necessary to charge and then discharge the gate of a
power MOSFET can be calculated as follows:
ΔTJ = PLOSS × θJA
Design Example
For example, consider driving two IRFS4310Z MOSFETs with a
VDD of 12 V at a switching frequency of 100 kHz, using an
ADP3630 in the MSOP package.
The maximum PCB temperature considered for this design is 85°C.
From the MOSFET data sheet, the total gate charge is QG = 120 nC.
PGATE = 12 V × 120 nC × 100 kHz = 144 mW
PDC = 12 V × 1.2 mA = 14.4 mW
PLOSS = 14.4 mW + (2 × 144 mW) = 302.4 mW
The MSOP thermal resistance is 162.2°C/W (see Table 3).
ΔTJ = 302.4 mW × 162.2°C/W = 49.0°C
PGATE = VGS × QG × fSW
TJ = TA + ΔTJ = 134.0°C ≤ TJ_MAX
where:
VGS is the bias voltage powering the driver (VDD).
QG is the total gate charge.
fSW is the maximum switching frequency.
This estimated junction temperature does not factor in the
power dissipated in the external gate resistor and, therefore,
provides a certain guard band.
The power dissipated for each gate (PGATE) must be multiplied
by the number of drivers (in this case, 1 or 2) being used in each
package; this PGATE value represents the total power dissipated in
charging and discharging the gates of the power MOSFETs.
If a lower junction temperature is required by the design,
the SOIC_N package, which provides a thermal resistance
of 110.6°C/W, can be used. Using the SOIC_N package, the
maximum junction temperature is
Not all of this power is dissipated in the gate driver because
part of it is actually dissipated in the external gate resistor, RG.
The larger the external gate resistor, the smaller the amount of
power that is dissipated in the gate driver.
In modern switching power applications, the value of the gate
resistor is kept at a minimum to increase switching speed and
to minimize switching losses.
ΔTJ = 302.4 mW × 110.6°C/W = 33.4°C
TJ = TA + ΔTJ = 118.4°C ≤ TJ_MAX
Other options to reduce power dissipation in the driver include
reducing the value of the VDD bias voltage, reducing the switching
frequency, and choosing a power MOSFET with a smaller gate
charge.
Rev. 0 | Page 13 of 16
ADP3629/ADP3630/ADP3631
OUTLINE DIMENSIONS
5.00 (0.1968)
4.80 (0.1890)
8
4.00 (0.1574)
3.80 (0.1497)
5
1
4
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
6.20 (0.2441)
5.80 (0.2284)
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
0.31 (0.0122)
COPLANARITY
0.10
SEATING
PLANE
0.50 (0.0196)
0.25 (0.0099)
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
012407-A
COMPLIANT TO JEDEC STANDARDS MS-012-A A
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 26. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-8)
Dimensions shown in millimeters and (inches)
3.20
3.00
2.80
8
3.20
3.00
2.80
1
5.15
4.90
4.65
5
4
PIN 1
IDENTIFIER
0.65 BSC
0.95
0.85
0.75
15° MAX
1.10 MAX
0.40
0.25
6°
0°
0.23
0.13
COMPLIANT TO JEDEC STANDARDS MO-187-AA
0.70
0.55
0.40
091709-A
0.15
0.05
COPLANARITY
0.10
Figure 27. 8-Lead Mini Small Outline Package [MSOP]
(RM-8)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADP3629ARZ-R7 1
ADP3629ARMZ-R71
ADP3630ARZ-R71
ADP3630ARMZ-R71
ADP3631ARZ-R71
ADP3631ARMZ-R71
1
Temperature
Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
8-Lead Standard Small Outline Package [SOIC_N]
8-Lead Mini Small Outline Package [MSOP]
8-Lead Standard Small Outline Package [SOIC_N]
8-Lead Mini Small Outline Package [MSOP]
8-Lead Standard Small Outline Package [SOIC_N]
8-Lead Mini Small Outline Package [MSOP]
Z = RoHS Compliant Part.
Rev. 0 | Page 14 of 16
Package
Option
R-8
RM-8
R-8
RM-8
R-8
RM-8
Ordering
Quantity
2,500
3,000
2,500
3,000
2,500
3,000
Branding
L8Q
L8R
L8S
ADP3629/ADP3630/ADP3631
NOTES
Rev. 0 | Page 15 of 16
ADP3629/ADP3630/ADP3631
NOTES
©2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D08401-0-9/09(0)
Rev. 0 | Page 16 of 16