GP1A10/GP1A26LC
GP1A10/GP1A26LC
OPIC Photointerrupter
with Connetor
■ Features
■ Applications
1. Uses 3-pin connector teminl
2. Supply voltage range ( VCC : 21 to 26V )
3. High sensig accuracy ( Slit width : 0.5mm )
4. Wide gap between light emitter and detector ( 5mm )
5. Connector towards upside ( GP1A26LC )
1. Copiers, Printers
2. Facsimiles
■ Outline Dimensions
( Unit : mm )
GP1A26LC
GP1A10
Internal connection diagram
Internal connection diagram
Voltage regulator
32
16.0 ± 0.2
6.0
1
(2.5)
R2.0
3.0 ± 0.1
4.5
*Unspecified tolerances shall be as follows;
Dimensions(d) Tolerance
d < 6.0
± 0.2
6.0 <= d
± 0.3
* ( ): Reference dimensions
❈ JAPAN AMP made
EI 3-pin connector 171826-3
Recommended connectors on the inserted side
JAPAN AMP made
Housing : 171822-3
Terminal : 170262 -1
etc. ❈❈
❈
1 GND
2 VO
3 V CC
6.0
f 3.0 ± 0.1
R2.0
(7.5)
4.0
4.5
(2.5)
3.0 ± 0.1
4.0
(7.5)
6.5
f 3.0 ± 0.1
(2.5)
3
(2.5)
6.5
3.0
38.0
3.0
(15.5)
2
(15.5)
(8.2)
❈
38.0
15.0
5.0
7.0 ± 0.2
46.0MAX.
7.0 ± 0.2
15.0
5.0
0.5 ± 0.1
Slit
width
4.4
1.4 ± 0.2
10.0
Slit
width
1.4 ± 0.2
0.5 ± 0.1
+ 0.5
- 0.3
4.4 (5.6)
0.2
5.0
16.0 ± 0.2
1
1
2
3
5.0
24.0±
(3.5)
24.0 ± 0.2
(3.5)
+ 0.5
0.3
3
Voltage regulator
1 GND
2 VO
3 V CC
10.0 -
2
(5.6)
1
*Unspecified tolerances shall be as follows;
Dimensions(d) Tolerance
± 0.2
d<6.0
± 0.3
6.0 <= d
* ( ) : Reference dimensions
❈ JAPAN AMP made
EI 3-pin connector 171825-3
Recommended connectors on the inserted side
JAPAN AMP made
Housing : 171822-3
Terminal : 170262 - 1
etc. ❈❈
* “ OPIC ” ( Optical IC ) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and signalprocessing circuit integrated onto a single chip.
❈❈ Recommended connectors on the inserted side( See674page ) .
“ In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs,
data books, etc. Contact SHARP in order to obtain the latest version of the device specification sheets before using any SHARP's device.”
GP1A10/GP1A26LC
■ Absolute Maximum Ratings
Parameter
Supply voltage
*1
Output voltage
*2
Low level output current
*3
Operating temperature
( Ta = 25˚C )
Symbol
V CC
VO
I OL
GP1A10
T opr
GP1A26LC
*3
Storage temperature
Operating humidity
T stg
RH
Rating
- 0.5 to + 30
- 0.5 to + 40
50
0 to + 80
- 20 to + 80
- 20 to + 95
10 to 95
Unit
V
V
mA
˚C
˚C
%
*1 Collector-emitter voltage of output transistor
*2 Collector current of output tranistor
*3 The connector should be plugged in/out at normal temperature.
■ Electro-optical Characteristics
Parameter
Operating supply voltage
Low level supply current
Low level output voltage
High level supply current
High level output voltage
Symbol
V CC
I CCL
V OL
I CCH
V OH
Minimum
interruption
time
Minimum
sensing
time
Response
characteristics
tH
tL
( Unless otherwise specified VCC = 24V, Ta = 25˚C )
conditions
Light beam uninterrupted
Light beam uninterrupted, I OL = 16mA
Light beam interrupted
Light beam interrupted, R L = 10kΩ , V CC = 26V
Ta= 0 to 80˚C R L = 4.7kΩ
V CC= 24V ± 5%
TYP.
-
MAX.
26
30
0.6
30
-
Unit
V
mA
V
mA
V
166
-
-
µs
166
-
-
µs
Fig. 2 Low Level Output Voltage vs.
Low Level Output Current
60
1
50
0.5
Low levle output voltage V OL ( V)
Low level output current I OL ( mA )
Fig. 1 Low Level Output Current vs.
Ambient Temperature
MIN.
21
25.8
40
30
20
10
VCC = 24V
T a = 25˚C
0.2
0.1
0.05
0.02
0
0.01
0
25
50
75 80
Ambient temperature Ta ( ˚C )
100
1
2
5
10
20
50
Low level output current I OL ( mA )
100
GP1A10/GP1A26LC
Fig. 3 Low Level Output Voltage vs.
Ambient Temperature
Fig. 4 Supply Current vs. Supply Voltage
0.6
30
V CC = 24V
Dashline = GP1A26LC
Supply current I CC ( mA )
Low level output voltage VOL ( V)
0.5
0.4
I OL= 30mA
0.3
0.2
16mA
0.1
20
T a = 0˚C
+ 25˚C
+ 80˚C
10 I CCL
{
I CCH
T a = 0˚C,+ 25˚C,+ 80˚C
5mA
0
0
- 25
25
50
75
100
0
20
21
22
23
24
25
26
27
Supply voltage V CC ( V)
Ambient temperature T a ( ˚C )
Fig. 5 Detecting Position Characteristics ( 1 )
Fig. 6 Detecting Position Characteristics ( 2 )
Output High
Output High
V CC = 24V
T a = 25˚C
R L = 10k Ω
V CC = 24V
T a = 25˚C
R L = 10kΩ
d Shield
h
Shield
Output Low
Output Low
0
1
2
3
4
5
Shield distance d ( mm )
Detecting position d = 3.0 ± 0.5mm
6
7
0
1
2
3
4
5
Shield distance h ( mm )
Detecting position h = 3.0 ± 1.0mm
6
7
GP1A10/GP1A26LC
■ Recommended Connectors on the Inserted Side
● JAPAN AMP made El series connectors
( standard type )
Housing color
Housing Model No.
Special
terminal
Model. No.
Natural
Black
Blue
Green
Red
color
171822-3 2-171822-3 4-171822-3 6-171822-3 8-171822-3
AWG
Product
Material Model No.
size
shape
Brass
170204-1
Bulk
Copper
170204-2
phosphide
AWG
26 to 20
Brass
170262-1
Chain
Copper
170262-2
phosphide
Brass
170205-1
Bulk
Copper
170205-2
phosphide
AWG
30 to 26
Brass
170263-1
Chain
Copper
170263-2
phosphide
● JAPAN AMP made El series connectors
( low profile type )
Housing color
Housing Model No.
Special
terminal
Model. No.
( Material:
Copper
phosphide )
Natural
Black
Blue
color
172142-3 2-172142-3 4-172142-3
AWG
Product shape
size
Bulk
AWG
26 to 22
Chain
Bulk
AWG
30 to 26
Chain
Green
Red
6-172142-3
8-172142-3
Model No.
170369-1
170354-1
170370-1
170355-1
● JAPAN AMP made El series connectors
( amp mass termination )
Housing-terminal
united type
connector
AWG26
AWG24 AWG22
AWG28
( Natural
( Black )
( Red )
( Green )
color )
172054-3 172053-3 172052-3 172051-3
❈ Terminal Material: Copper phosphide
■ Precautions for Use
( 1 ) It is recommended that a by-pass capacitor of more than 0.01µ F be added between VCC and
GND near the device in order to stabilize power supply line.
( 2 ) In this product, the PWB is fixed with a rear cover, and cleaning solvent may remain inside
the case ; therefore, dip cleaning or ultrasonic cleaning is prohibited.
( 3 ) Remove dust or stains, using an air blower or a soft cloth moistened in cleaning solvent.
However, do not perform the above cleaning using a soft cloth with cleaning solvent in the
marking portion.
In this case, use only the following type of cleaning solvent used for wiping off:
Ethyl alcohol, Methyl alcohol, Isopropyl alcohol, Freon TE, Freon TF, Diflon solvent S3-E
When the cleaning solvents except for specified materials are used, please consult us.
( 4 ) As for other general cautlons, refer to the chapter “ Precautions for Use ” .