ETC FCPS-2404

DF-52202 • D-110
July 13, 2004
FCPS-2404
24 Volt, 4 Amp NAC Power Expander
www.firelite.com
Section: Power Supplies/Accessories
GENERAL
The Fire•Lite FCPS-2404 is a compact, cost-effective, NAC
power expander. Its filtered 24 VDC output can provide up
to 4.0 amps of current to drive one Style Y (Class B) NAC
(Notification Appliance Circuit). The FACP's (Fire Alarm
Control Panel) NAC is connected to the power expander's
input circuit. When the control input circuit activates due to
reverse polarity of the FACP's NAC, the power expander
will activate its NAC circuit. The FCPS-2404 is compatible
with 12 VDC and 24 VDC control panels.
California
State Fire
Marshal
7315-0075:197
MEA
141-01-E
S2424
FEATURES
• 4 amps total of continuous current available.
• One 24 VDC Style Y (Class B) NAC.
• One optically-isolated input/control circuit, compatible with
12 VDC and 24 VDC control panel.
• External Strobe Synchronization could be added with UL
listed synch module, which can be housed in the FCPS2404.
• Can be wired daisy-chain style.
• Self-contained in compact, lockable cabinet (15" [381
mm] H x 14.5" [368 mm] W x 3.050" [775 mm] D).
• Output is filtered and completely power limited.
• Integrated supervised battery charger for lead acid or gel
type batteries.
• Uses only 7 AH (Amp Hour) batteries — can be
accomodated in the power supply cabinet.
• NAC supervised by host FACP.
• Earth fault detection by host FACP.
• Fixed terminal blocks for field wiring capable of accepting
12 – 22 AWG wire.
• AC fail Form-C relay contacts (fail-safe).
• Battery/Charger trouble Form-C relay contacts (fail safe).
• Optional hardware kit #90273 to be used when installing
addressable or synchronization modules.
LED INDICATORS
• AC power on (green) LED.
• Battery/Charger trouble (yellow) LED.
SPECIFICATIONS
Primary (AC) Power – TB1
• 120 VAC 50/60 Hz, 1.45 amps maximum.
• Wire size: minimum #14 AWG (2 mm²) with 600V insulation.
Control Input Circuit – TB3, Terminals 1 (+) & 2 (–)
alarm polarity
• Trigger Input Voltage: 9 to 32 VDC.
• Input Current Draw in Alarm Polarity:
16 - 32 volts, 10 mA maximum.
9 -16 volts, 4 mA maximum.
FCPS-2404
Important: Do not use shielded wire for Control Input
Circuit.
NAC Output Circuit – TB3, Terminals 3 (+) & 4 (–) alarm
polarity
• Voltage Rating: 24 VDC.
• Current: 4 amps maximum total continuous current.
• Style Y (Class B) – requires End-of-Line Resistor from
circuit connected to input.
• Refer to Fire•Lite Device Compatibility Document for listed
compatible devices.
Important: Do not use shielded wire for NAC Output
Circuit.
AC Fail Relay Contact Rating – TB6
• Fail-safe relay (normally energized, transfers with loss of
power).
• 1 amp @ 30 VDC.
Fire•Lite® Alarms is a Honeywell company.
This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.
For more information, contact Fire•Lite Alarms, One Fire-Lite Place, Northford, Connecticut 06472. Phone:
(800) 627-3473, Toll-Free FAX: (877) 699-4105.
DF-52202 • 07/13/04 — Page 1 of 3
Battery/ChargerTrouble Contact Rating – TB5
• Fail-safe relay (normally energized, transfers with loss of
power).
• 1 amp @ 30 VDC.
Secondary Power (Battery) Charging Circuit
• Maximum Battery Capacity: use only 7.0 AH batteries.
• FCPS-2404 draws maximum standby current of 40 mA
from batteries (includes End-of-Line Relay currrent if installed).
Auxiliary Power Connector – P3
• Used for powering modules inside cabinet, such as control
modules.
• Voltage Rating: 24 VDC.
• Current: 30 mA maximum.
• Supports lead acid and gel type batteries only.
• Float Charge Voltage: 27.6 VDC.
• Maximum Charge Current: 750 mA.
FCPS-2404 BOARD LAYOUT
NAC Output - supervised
(alarm polarity shown)
Battery/Charger Trouble
Relay Contacts
NAC Input from FACP - supervised
(alarm polarity shown)
Note: No T-tapping addtional
notification appliances
Important: Do not use shielded
wire for Control Input or NAC
Output Circtuits
AC Fail
Report
Jumper
AC Fail
Relays Contacts
P3 Internal 24 VDC Power
(nonsupervised)
TB1 AC Power Connector
(supervised)
P2 Battery Connector
(supervised)
2404bord.wmf
F2 Fuse 8 amp for Battery
Page 2 of 3 — DF-52202 • 07/13/04
F1 Fuse 1 amp for Charger
CONTROLLING FCPS-2404 WITH
CONTROL MODULE AND INTERNAL POWER
Polarized Bell
SLC Out to next
addressable device
Strobe
Horn
SLC In from FACP
or previous
addressable device
-
+
+
24 VDC
Control Module
or Sync Module
+
24 VDC
FCPS-2404
Control Module
mounting (if Sync
Module used above) or
second Control Module
2404app.wmf
PRODUCT LINE INFORMATION
FCPS-2404
NAC power expander (120 VAC). Includes
main printed circuit board, transformers, red
enclosure, and installation instructions.
CMF-300
Intelligent addressable control module.
MDL
Sync module for use with SpectrAlert Series,
red.
MDLW
Sync module for use with SpectrAlert Series,
white.
BAT-1270
Battery, 12 volt, 7.0 AH (two required).
90273
Hardware kit to be used when installing
addressable or synch modules.
FCPS-24RB Replacement motherboard.
DF-52202 • 07/13/04 — Page 3 of 3