TI LM1881MX/NOPB

LM1881
www.ti.com
SNLS384F – FEBRUARY 1995 – REVISED MARCH 2013
LM1881 Video Sync Separator
Check for Samples: LM1881
FEATURES
DESCRIPTION
•
•
•
•
•
•
•
•
•
The LM1881 Video sync separator extracts timing
information including composite and vertical sync,
burst/back porch timing, and odd/even field
information from standard negative going sync NTSC,
PAL (1) and SECAM video signals with amplitude from
0.5V to 2V p-p. The integrated circuit is also capable
of providing sync separation for non-standard, faster
horizontal rate video signals. The vertical output is
produced on the rising edge of the first serration in
the vertical sync period. A default vertical output is
produced after a time delay if the rising edge
mentioned above does not occur within the externally
set delay period, such as might be the case for a
non-standard video signal.
1
2
AC Coupled Composite Input Signal
>10 kΩ Input Resistance
<10 mA Power Supply Drain Current
Composite Sync and Vertical Outputs
Odd/Even Field Output
Burst Gate/Back Porch Output
Horizontal Scan Rates to 150 kHz
Edge Triggered Vertical Output
Default Triggered Vertical Output for Nonstandard Video Signal (Video Games-Home
Computers)
(1)
PAL in this datasheet refers to European broadcast TV
standard “Phase Alternating Line”, and not to Programmable
Array Logic.
Connection Diagram
Figure 1. LM1881N
See Package Number D0008A or P0008E
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1995–2013, Texas Instruments Incorporated
LM1881
SNLS384F – FEBRUARY 1995 – REVISED MARCH 2013
Absolute Maximum Ratings
www.ti.com
(1) (2)
Supply Voltage
13.2V
Input Voltage
3 VP-P (VCC = 5V)
6 VP-P (VCC ≥ 8V)
Output Sink Currents; Pins, 1, 3, 5
5 mA
Output Sink Current; Pin 7
Package Dissipation
2 mA
(3)
1100 mW
−65°C to +150°C
Storage Temperature Range
ESD Susceptibility
(4)
2 kV
ESD Susceptibility
(5)
200 V
Soldering Information
PDIP Package (10 sec.)
260°C
SOIC Package
(1)
(2)
(3)
(4)
(5)
Vapor Phase (60 sec.)
215°C
Infrared (15 sec.)
220°C
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. For ensured specifications and test
conditions, see the Electrical Characteristics. The ensured specifications apply only for the test conditions listed.
If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications.
For operation in ambient temperatures above 25°C, the device must be derated based on a 150°C maximum junction temperature and a
package thermal resistance of 110°C/W, junction to ambient.
ESD susceptibility test uses the “human body model, 100 pF discharged through a 1.5 kΩ resistor”.
Machine Model, 220 pF – 240 pF discharged through all pins.
Electrical Characteristics LM1881
VCC = 5V; RSET = 680 kΩ; TA = 0°C to +70°C by correlation with 100% electrical testing at TA=25°C
Parameter
Conditions
Supply Current
Outputs at
Logic 1
DC Input Voltage
Pin 2
(2)
Input Threshold Voltage
Min
(1)
Max
Units
5.2
5.5
10
12
mA
1.3
1.5
1.8
V
55
70
85
mV
16
VCC = 5V
VCC = 12V
Typ
Input Discharge Current
Pin 2; VIN = 2V
6
11
Input Clamp Charge Current
Pin 2; VIN = 1V
0.2
0.8
RSET Pin Reference Voltage
Pin 6;
(3)
1.10
1.22
Composite Sync. & Vertical
Outputs
IOUT = 40 µA;
Logic 1
VCC = 5V
VCC = 12V
4.0
11.0
4.5
IOUT = 1.6 mA
Logic 1
VCC = 5V
VCC = 12V
2.4
10.0
3.6
Burst Gate & Odd/Even Outputs
IOUT = 40 µA;
Logic 1
VCC = 5V
VCC = 12V
4.0
11.0
4.5
Composite Sync. Output
IOUT = −1.6 mA; Logic 0; Pin 1
0.2
0.8
V
Vertical Sync. Output
IOUT = −1.6 mA; Logic 0; Pin 3
0.2
0.8
V
Burst Gate Output
IOUT = −1.6 mA; Logic 0; Pin 5
0.2
0.8
V
Odd/Even Output
IOUT = −1.6 mA; Logic 0; Pin 7
0.2
0.8
V
230
300
µs
2.5
4
4.7
µs
32
65
90
µs
Vertical Sync Width
Burst Gate Width
Vertical Default Time
(1)
(2)
(3)
(4)
2
190
2.7 kΩ from Pin 5 to VCC
(4)
µA
mA
1.35
V
V
V
V
Typicals are at TJ = 25°C and represent the most likely parametric norm.
Relative difference between the input clamp voltage and the minimum input voltage which produces a horizontal output pulse.
Careful attention should be made to prevent parasitic capacitance coupling from any output pin (Pins 1, 3, 5 and 7) to the RSET pin (Pin
6).
Delay time between the start of vertical sync (at input) and the vertical output pulse.
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1881
LM1881
www.ti.com
SNLS384F – FEBRUARY 1995 – REVISED MARCH 2013
Typical Performance Characteristics
RSET Value Selection
vs
Vertical Serration Pulse Separation
Vertical Default Sync Delay Time
vs
RSET
Figure 2.
Figure 3.
Burst/Black Level Gate Time
vs
RSET
Vertical Pulse Width
vs
RSET
Figure 4.
Figure 5.
Vertical Pulse Width
vs
Temperature
Supply Current
vs
Supply Voltage
VERTICAL PULSE WIDTH (Ps)
500
400
300
200
100
-40
-20
0
20
40
60
80
100
TEMPERATURE (°C)
Figure 6.
Figure 7.
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1881
3
LM1881
SNLS384F – FEBRUARY 1995 – REVISED MARCH 2013
www.ti.com
APPLICATION NOTES
The LM1881 is designed to strip the synchronization signals from composite video sources that are in, or similar
to, the N.T.S.C. format. Input signals with positive polarity video (increasing signal voltage signifies increasing
scene brightness) from 0.5V (p-p) to 2V (p-p) can be accommodated. The LM1881 operates from a single supply
voltage between 5V DC and 12V DC. The only required external components besides a power supply decoupling
capacitor at pin 8 and a set current decoupling capacitor at pin 6, are the composite input coupling capacitor at
pin 2 and one resistor at pin 6 that sets internal current levels. The resistor on pin 6 (i.e. Rset) allows the LM1881
to be adjusted for source signals with line scan frequencies differing from 15.734 kHz. Four major sync signals
are available from the I/C; composite sync including both horizontal and vertical scan timing information; a
vertical sync pulse; a burst gate or back porch clamp pulse; and an odd/even output. The odd/even output level
identifies which video field of an interlaced video source is present at the input. The outputs from the LM1881
can be used to gen-lock video camera/VTR signals with graphics sources, provide identification of video fields for
memory storage, recover suppressed or contaminated sync signals, and provide timing references for the
extraction of coded or uncoded data on specific video scan lines.
To better understand the LM1881 timing information and the type of signals that are used, refer to Figure 8(a-e)
which shows a portion of the composite video signal from the end of one field through the beginning of the next
field.
COMPOSITE SYNC OUTPUT
The composite sync output, Figure 8(b), is simply a reproduction of the signal waveform below the composite
video black level, with the video completely removed. This is obtained by clamping the video signal sync tips to
1.5V DC at Pin 2 and using a comparator threshold set just above this voltage to strip the sync signal, which is
then buffered out to Pin 1. The threshold separation from the clamped sync tip is nominally 70 mV which means
that for the minimum input level of 0.5V (p-p), the clipping level is close to the halfway point on the sync pulse
amplitude (shown by the dashed line on Figure 8(a). This threshold separation is independent of the signal
amplitude, therefore, for a 2V (p-p) input the clipping level occurs at 11% of the sync pulse amplitude. The
charging current for the input coupling capacitor is 0.8 mA,
Normally the signal source for the LM1881 is assumed to be clean and relatively noise-free, but some sources
may have excessive video peaking, causing high frequency video and chroma components to extend below the
black level reference. Some video discs keep the chroma burst pulse present throughout the vertical blanking
period so that the burst actually appears on the sync tips for three line periods instead of at black level. A clean
composite sync signal can be generated from these sources by filtering the input signal. When the source
impedance is low, typically 75Ω, a 620Ω resistor in series with the source and a 510 pF capacitor to ground will
form a low pass filter with a corner frequency of 500 kHz. This bandwidth is more than sufficient to pass the sync
pulse portion of the waveform; however, any subcarrier content in the signal will be attenuated by almost 18 dB,
effectively taking it below the comparator threshold. Filtering will also help if the source is contaminated with
thermal noise. The output waveforms will become delayed from between 40 ns to as much as 200 ns due to this
filter. This much delay will not usually be significant but it does contribute to the sync delay produced by any
additional signal processing. Since the original video may also undergo processing, the need for time delay
correction will depend on the total system, not just the sync stripper.
VERTICAL SYNC OUTPUT
A vertical sync output is derived by internally integrating the composite sync waveform (Figure 9). To understand
the generation of the vertical sync pulse, refer to the lower left hand section Figure 9. Note that there are two
comparators in the section. One comparator has an internally generated voltage reference called V1 going to one
of its inputs. The other comparator has an internally generated voltage reference called V2 going to one of its
inputs. Both comparators have a common input at their noninverting input coming from the internal integrator.
The internal integrator is used for integrating the composite sync signal. This signal comes from the input side of
the composite sync buffer and are positive going sync pulses. The capacitor to the integrator is internal to the
LM1881. The capacitor charge current is set by the value of the external resistor RSET. The output of the
integrator is going to be at a low voltage during the normal horizontal lines because the integrator has a very
short time to charge the capacitor, which is during the horizontal sync period. The equalization pulses will keep
the output voltage of the integrator at about the same level, below the V1. During the vertical sync period the
narrow going positive pulses shown in Figure 8 is called the serration pulse. The wide negative portion of the
vertical sync period is called the vertical sync pulse. At the start of the vertical sync period, before the first
Serration pulse occurs, the integrator now charges the capacitor to a much higher voltage. At the first serration
4
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1881
LM1881
www.ti.com
SNLS384F – FEBRUARY 1995 – REVISED MARCH 2013
pulse the integrator output should be between V1 and V2. This would give a high level at the output of the
comparator with V1 as one of its inputs. This high is clocked into the “D” flip-flop by the falling edge of the
serration pulse (remember the sync signal is inverted in this section of the LM1881). The “Q” output of the “D”
flip-flop goes through the OR gate, and sets the R/S flip-flop. The output of the R/S flip-flop enables the internal
oscillator and also clocks the ODD/EVEN “D” flip-flop. The ODD/EVEN field pulse operation is covered in the
next section. The output of the oscillator goes to a divide by 8 circuit, thus resetting the R/S flip-flop after 8 cycles
of the oscillator. The frequency of the oscillator is established by the internal capacitor going to the oscillator and
the external RSET. The “Q” output of the R/S flip-flop goes to pin 3 and is the actual vertical sync output of the
LM1881. By clocking the “D” flip-flop at the start of the first serration pulse means that the vertical sync output
pulse starts at this point in time and lasts for eight cycles of the internal oscillator as shown in Figure 8.
How RSET affects the integrator and the internal oscillator is shown under the Typical Performance
Characteristics. The first graph is “RSET Value Selection vs Vertical Serration Pulse Separation”. For this graph to
be valid, the vertical sync pulse should last for at least 85% of the horizontal half line (47% of a full horizontal
line). A vertical sync pulse from any standard should meet this requirement; both NTSC and PAL do meet this
requirement (the serration pulse is the remainder of the period, 10% to 15% of the horizontal half line).
Remember this pulse is a positive pulse at the integrator but negative in Figure 8. This graph shows how long it
takes the integrator to charge its internal capacitor above V1.
With RSET too large the charging current of the integrator will be too small to charge the capacitor above V1, thus
there will be no vertical synch output pulse. As mentioned above, RSET also sets the frequency of the internal
oscillator. If the oscillator runs too fast its eight cycles will be shorter than the vertical sync portion of the
composite sync. Under this condition another vertical sync pulse can be generated on one of the later serration
pulse after the divide by 8 circuit resets the R/S flip-flop. The first graph also shows the minimum RSET necessary
to prevent a double vertical pulse, assuming that the serration pulses last for only three full horizontal line periods
(six serration pulses for NTSC). The actual pulse width of the vertical sync pulse is shown in the “Vertical Pulse
Width vs RSET” graph. Using NTSC as an example, lets see how these two graphs relate to each other. The
Horizontal line is 64 µs long, or 32 µs for a horizontal half line. Now round this off to 30 µs. In the “RSET Value
Selection vs Vertical Serration Pulse Separation” graph the minimum resistor value for 30 µs serration pulse
separation is about 550 kΩ. Going to the “Vertical Pulse Width vs RSET” graph one can see that 550 kΩ gives a
vertical pulse width of about 180 µs, the total time for the vertical sync period of NTSC (3 horizontal lines). A 550
kΩ will set the internal oscillator to a frequency such that eight cycles gives a time of 180 µs, just long enough to
prevent a double vertical sync pulse at the vertical sync output of the LM1881.
The LM1881 also generates a default vertical sync pulse when the vertical sync period is unusually long and has
no serration pulses. With a very long vertical sync time the integrator has time to charge its internal capacitor
above the voltage level V2. Since there is no falling edge at the end of a serration pulse to clock the “D” flip-flop,
the only high signal going to the OR gate is from the default comparator when output of the integrator reaches
V2. At this time the R/S flip-flop is toggled by the default comparator, starting the vertical sync pulse at pin 3 of
the LM1881. If the default vertical sync period ends before the end of the input vertical sync period, then the
falling edge of the vertical sync (positive pulse at the “D” flip-flop) will clock the high output from the comparator
with V1 as a reference input. This will retrigger the oscillator, generating a second vertical sync output pulse. The
“Vertical Default Sync Delay Time vs RSET” graph shows the relationship between the RSET value and the delay
time from the start of the vertical sync period before the default vertical sync pulse is generated. Using the NTSC
example again the smallest resistor for RSET is 500 kΩ. The vertical default time delay is about 50 µs, much
longer than the 30 µs serration pulse spacing.
A common question is how can one calculate the required RSET with a video timing standard that has no
serration pulses during the vertical blanking. If the default vertical sync is to be used this is a very easy task. Use
the “Vertical Default Sync Delay Time vs RSET” graph to select the necessary RSET to give the desired delay time
for the vertical sync output signal. If a second pulse is undesirable, then check the “Vertical Pulse Width vs RSET”
graph to make sure the vertical output pulse will extend beyond the end of the input vertical sync period. In most
systems the end of the vertical sync period may be very accurate. In this case the preferred design may be to
start the vertical sync pulse at the end of the vertical sync period, similar to starting the vertical sync pulse after
the first serration pulse. A VGA standard is to be used as an example to show how this is done. In this standard
a horizontal line is 32 µs long. The vertical sync period is two horizontal lines long, or 64 µs. The vertical default
sync delay time must be longer than the vertical sync period of 64 µs. In this case RSET must be larger than 680
kΩ. RSET must still be small enough for the output of the integrator to reach V1 before the end of the vertical
period of the input pulse. The first graph can be used to confirm that RSET is small enough for the integrator.
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1881
5
LM1881
SNLS384F – FEBRUARY 1995 – REVISED MARCH 2013
www.ti.com
Instead of using the vertical serration pulse separation, use the actual pulse width of the vertical sync period, or
64 µs in this example. This graph is linear, meaning that a value as large as 2.7 MΩ can be used for RSET (twice
the value as the maximum at 30 µs). Due to leakage currents it is advisable to keep the value of RSET under 2.0
MΩ. In this example a value of 1.0 MΩ is selected, well above the minimum of 680 kΩ. With this value for RSET
the pulse width of the vertical sync output pulse of the LM1881 is about 340 µs.
Figure 8. (a) Composite Video; (b) Composite Sync; (c) Vertical Output Pulse;
(d) Odd/Even Field Index; (e) Burst Gate/Back Porch Clamp
6
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1881
LM1881
www.ti.com
SNLS384F – FEBRUARY 1995 – REVISED MARCH 2013
*Components Optional, See Text
Figure 9.
ODD/EVEN FIELD PULSE
An unusual feature of LM1881 is an output level from Pin 7 that identifies the video field present at the input to
the LM1881. This can be useful in frame memory storage applications or in extracting test signals that occur in
alternate fields. For a composite video signal that is interlaced, one of the two fields that make up each video
frame or picture must have a half horizontal scan line period at the end of the vertical scan—i.e., at the bottom of
the picture. This is called the “odd field” or “even field”. The “even field” or “field 2” has a complete horizontal
scan line at the end of the field. An odd field starts on the leading edge of the first equalizing pulse, whereas the
even field starts on the leading edge of the second equalizing pulse of the vertical retrace interval. Figure 8(a)
shows the end of the even field and the start of the odd field.
To detect the odd/even fields the LM1881 again integrates the composite sync waveform (Figure 9). A capacitor
is charged during the period between sync pulses and discharged when the sync pulse is present. The period
between normal horizontal sync pulses is enough to allow the capacitor voltage to reach a threshold level of a
comparator that clears a flip-flop which is also being clocked by the sync waveform. When the vertical interval is
reached, the shorter integration time between equalizing pulses prevents this threshold from being reached and
the Q output of the flip-flop is toggled with each equalizing pulse. Since the half line period at the end of the odd
field will have the same effect as an equalizing pulse period, the Q output will have a different polarity on
successive fields. Thus by comparing the Q polarity with the vertical output pulse, an odd/even field index is
generated. Pin 7 remains low during the even field and high during the odd field.
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1881
7
LM1881
SNLS384F – FEBRUARY 1995 – REVISED MARCH 2013
www.ti.com
BURST/BACKPORCH OUTPUT PULSE
In a composite video signal, the chroma burst is located on the backporch of the horizontal blanking period. This
period, approximately 4.8 µs long, is also the black level reference for the subsequent video scan line. The
LM1881 generates a pulse at Pin 5 that can be used either to retrieve the chroma burst from the composite video
signal (thus providing a subcarrier synchronizing signal) or as a clamp for the DC restoration of the video
waveform. This output is obtained simply by charging an internal capacitor starting on the trailing edge of the
horizontal sync pulses. Simultaneously the output of Pin 5 is pulled low and held until the capacitor charge circuit
times out—4 µs later. A shorter output burst gate pulse can be derived by differentiating the burst output using a
series C-R network. This may be necessary in applications which require high horizontal scan rates in
combination with normal (60 Hz–120 Hz) vertical scan rates.
APPLICATIONS
Apart from extracting a composite sync signal free of video information, the LM1881 outputs allow a number of
interesting applications to be developed. As mentioned above, the burst gate/backporch clamp pulse allows DC
restoration of the original video waveform for display or remodulation on an R.F. carrier, and retrieval of the color
burst for color synchronization and decoding into R.G.B. components. For frame memory storage applications,
the odd/even field lever allows identification of the appropriate field ensuring the correct read or write sequence.
The vertical pulse output is particularly useful since it begins at a precise time—the rising edge of the first vertical
serration in the sync waveform. This means that individual lines within the vertical blanking period (or anywhere
in the active scan line period) can easily be extracted by counting the required number of transitions in the
composite sync waveform following the start of the vertical output pulse.
The vertical blanking interval is proving popular as a means to transmit data which will not appear on a normal
T.V. receiver screen. Data can be inserted beginning with line 10 (the first horizontal scan line on which the color
burst appears) through to line 21. Usually lines 10 through 13 are not used which leaves lines 14 through 21 for
inserting signals, which may be different from field to field. In the U.S., line 19 is normally reserved for a vertical
interval reference signal (VIRS) and line 21 is reserved for closed caption data for the hearing impaired. The
remaining lines are used in a number of ways. Lines 17 and 18 are frequently used during studio processing to
add and delete vertical interval test signals (VITS) while lines 14 through 18 and line 20 can be used for
Videotex/Teletext data. Several institutions are proposing to transmit financial data on line 17 and cable systems
use the available lines in the vertical interval to send decoding data for descrambler terminals.
Since the vertical output pulse from the LM1881 coincides with the leading edge of the first vertical serration,
sixteen positive or negative transitions later will be the start of line 14 in either field. At this point simple counters
can be used to select the desired line(s) for insertion or deletion of data.
VIDEO LINE SELECTOR
The circuit in Figure 10 puts out a singe video line according to the binary coded information applied to line
select bits b0–b7. A line is selected by adding two to the desired line number, converting to a binary equivalent
and applying the result to the line select inputs. The falling edge of the LM1881's vertical pulse is used to load
the appropriate number into the counters (MM74C193N) and to set a start count latch using two NAND gates.
Composite sync transitions are counted using the borrow out of the desired number of counters. The final borrow
out pulse is used to turn on the analog switch (CD4066BC) during the desired line. The falling edge of this signal
also resets the start count latch, thereby terminating the counting.
The circuit, as shown, will provide a single line output for each field in an interlaced video system (television) or a
single line output in each frame for a non-interlaced video system (computer monitor). When a particular line in
only one field of an interlaced video signal is desired, the odd/even field index output must be used instead of the
vertical output pulse (invert the field index output to select the odd field). A single counter is needed for selecting
lines 3 to 14; two counters are needed for selecting lines 15 to 253; and three counters will work for up to 2046
lines. An output buffer is required to drive low impedance loads.
8
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1881
LM1881
www.ti.com
SNLS384F – FEBRUARY 1995 – REVISED MARCH 2013
MULTIPLE CONTIGUOUS VIDEO LINE
SELECTOR WITH BLACK LEVEL RESTORATION
The circuit in Figure 11 will select a number of adjoining lines starting with the line selected as in the previous
example. Additional counters can be added as described previously for either higher starting line numbers or an
increased number of contiguous output lines. The back porch pulse output of the LM1881 is used to gate the
video input's black level through a low pass filter (10 kΩ, 10 µF) providing black level restoration at the video
output when the output selected line(s) is not being gated through.
Typical Applications
Figure 10. Video Line Selector
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1881
9
LM1881
SNLS384F – FEBRUARY 1995 – REVISED MARCH 2013
www.ti.com
Figure 11. Multiple Contiguous Video Line Selector with Black Level Restoration
10
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1881
LM1881
www.ti.com
SNLS384F – FEBRUARY 1995 – REVISED MARCH 2013
REVISION HISTORY
Changes from Revision E (March 2013) to Revision F
•
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 10
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1881
11
PACKAGE OPTION ADDENDUM
www.ti.com
27-Jul-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
LM1881M
ACTIVE
SOIC
D
8
95
TBD
Call TI
Call TI
0 to 70
LM
1881M
LM1881M/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
0 to 70
LM
1881M
LM1881MX
ACTIVE
SOIC
D
8
2500
TBD
Call TI
Call TI
0 to 70
LM
1881M
LM1881MX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
0 to 70
LM
1881M
LM1881N
ACTIVE
PDIP
P
8
40
TBD
Call TI
Call TI
0 to 70
LM1881N
LM1881N/NOPB
ACTIVE
PDIP
P
8
40
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
0 to 70
LM1881N
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
27-Jul-2013
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Mar-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LM1881MX
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LM1881MX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Mar-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM1881MX
SOIC
D
8
2500
349.0
337.0
45.0
LM1881MX/NOPB
SOIC
D
8
2500
349.0
337.0
45.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated