MICREL MIC58P01BWM

MIC58P01
Micrel
MIC58P01
8-Bit Parallel-Input Protected Latched Driver
Final Information
General Description
Features
The MIC58P01 parallel-input latched driver is a high-voltage
(80V), high-current (500mA) integrated circuit comprised of
eight CMOS data latches, a bipolar Darlington transistor
driver for each latch, and CMOS control circuitry for the
common CLEAR, STROBE, and OUTPUT ENABLE functions.
Similar to the MIC5801, additional protection circuitry supplied
on this device includes thermal shutdown, under voltage
lockout (UVLO), and overcurrent shutdown.
•
•
•
•
•
•
•
•
•
The bipolar/CMOS combination provides an extremely lowpower latch with maximum interface flexibility. The MIC58P01
has open-collector outputs capable of sinking 500 mA and
integral diodes for inductive load transient suppression with a
minimum output breakdown voltage rating of 80V (50V
sustaining). The drivers may be paralleled for higher load
current capability.
With a 5V logic supply, the MIC58P01 will typically operate at
better than 5MHz. With a 12V logic supply, significantly higher
speeds are obtained. The CMOS inputs are compatible with
standard CMOS, PMOS, and NMOS circuits. TTL circuits
may require pull-up resistors.
4.4MHz Minimum Data Input Rate
High-Voltage, High-Current Outputs
Per-Output Overcurrent Shutdown (500mA typical)
Under Voltage Lockout
Thermal Shutdown
Output Transient Protection Diodes
CMOS, PMOS, NMOS, and TTL Compatible Inputs
Internal Pull-Down Resistors
Low-Power CMOS Latches
Ordering Information
Part Number
Each of these eight outputs has an independent overcurrent
shutdown of 500mA. Upon current shutdown, the affected
channel will turn OFF until VDD is cycled or the ENABLE/
RESET pin is pulsed high. Current pulses less than 2µs will
not activate current shutdown. Temperatures above 165°C
will shut down all outputs. The UVLO circuit disables the
outputs at low VDD; hysteresis of 0.5V is provided.
Temperature Range
Package
MIC58P01BN
–40°C to +85°C
22-Pin Plastic DIP
MIC58P01BV
–40°C to +85°C
28-Pin PLCC
MIC58P01BWM
–40°C to +85°C
24-Pin Wide SOIC
Functional Diagram
Pin Configuration
(DIP)
ENABLE/RESET
ISHUTDOWN
V DD
-
+
IOUT / N
2.2R
1.25V
R
+
–
UVLO
COMMON
THERMAL
SHUTDOWN
S
R
Q
OUTPUT
IN
22
OUTPUT
ENABLE/RESET
21
VDD
3
20
OUT1
IN2
4
19
OUT2
IN3
5
18
OUT3
IN4
6
17
OUT4
IN5
7
16
OUT5
IN6
8
15
OUT6
IN7
9
14
OUT7
IN8 10
13
OUT8
12
COMMON
CLEAR
1
STROBE
2
IN1
I LIMIT AND
THERMAL
SHUTDOWN
IREF
R1
70k
Circuitry below dashed line is
included in each of the 8 channels.
R2
3k
LATCHES
CLEAR
STROBE
V EE
GROUND 11
UVLO
Micrel, Inc. • 1849 Fortune Drive • San Jose, CA 95131 • USA • tel + 1 (408) 944-0800 • fax + 1 (408) 944-0970 • http://www.micrel.com
October 1998
1
MIC58P01
MIC58P01
Micrel
Pin Configuration, Continued
Absolute Maximum Ratings: (Note 1)
NC
2
VDD
NC
3
CLEAR
STROBE
4
OE/RESET
NC
at +25°C Free-Air Temperature
1
28
27
26
IN 1
5
25
OUT 1
IN 2
6
24
OUT 2
IN 3
7
23
OUT 3
IN 4
8
22
OUT 4
MIC58P01BV
IN 5
9
21
OUT 5
IN 6
10
20
OUT 6
IN 7
11
19
OUT 7
17
18
80V
15V
–0.3V to VDD + 0.3V
2.25W
22.5mW/°C
1.6W
16mW/°C
1.4W
14mW/°C
–55°C to +85°C
–65°C to +125°C
Note 1: Micrel CMOS devices have input-static protection but are
susceptible to damage when exposed to extremely high static
electrical charges.
OUT 8
NC
16
COMMON
15
GROUND
14
NC
13
NC
IN 8
12
Output Voltage, VCE
Supply Voltage, VDD
Input Voltage Range, VIN
Package Power Dissipation:
MIC58P01BN
Derate above TA = +25°C
MIC58P01BV
Derate above TA = +25°C
MIC58P01BWM
Derate above TA = +25°C
Operating Temperature Range, TA
Storage Temperature Range, TS
MIC58P01BV, 28–Pin PLCC
Typical Input
V DD
GROUND
1
24
CLEAR
2
23
STROBE
3
22
OUTPUT
ENABLE/RESET
VDD
IN1
4
21
OUT1
IN2
5
20
OUT2
IN3
6
19
OUT3
IN4
7
18
OUT4
IN5
8
17
OUT5
IN6
9
16
OUT6
IN7 10
15
OUT7
IN8 11
14
OUT8
GROUND 12
13
COMMON
IN
Allowable Output Current As A Function
of Duty Cycle
ALLOWABLE COLLECTOR CURRENT IN mA AT 50°C
MIC58P01BWM
NC
MIC58P01BWM, 24–Pin SOIC
(not pin compatible with MIC5801BWM)
MIC58P01BN
450
400
1 or 2
350
3
4
300
5
6
250
7
8
200
NUMBER OF OUTPUTS
CONDUCTING
SIMULTANEOUSLY
150
100
0
10
20
30
40
50
60
70
80
90
100
PERCENT DUTY CYCLE
Pin Description
Pin (DIP)
Name
Description
1
CLEAR
Resets all Latches and turns all outputs OFF (open).
2
STROBE
Input Strobe Pin. Loads output latches when High.
3–10
INPUT
Parallel Inputs, 1 through 8
11
GROUND
Logic and Output Ground pin.
12
COMMON
Transient suppression diode common cathode pin.
13–20
OUTPUT
Parallel Outputs, 8 through 1.
21
VDD
Logic Supply voltage.
22
OUTPUT
ENABLE/RESET
When Low, Outputs are active. When High, outputs are inactive and device is reset
from a fault condition. An undervoltage condition emulates a high OE input.
MIC58P01
2
October 1998
MIC58P01
Micrel
Electrical Characteristics (Note 3): at TA = +25°C, VDD = 5V (unless otherwise noted)
Limits
Characteristic
Symbol
Test Conditions
Output Leakage Current
ICEX
VCE = 80V, TA = +25°C
50
VCE = 80V, TA = +70°C
100
Collector-Emitter
VCE(SAT)
Saturation Voltage
Input Voltage
Min.
Typ.
IC = 100mA
0.9
1.1
IC = 200mA
1.1
1.3
IC = 350mA
1.3
1.6
VDD = 12V
VIN(1)
RIN
Supply Current
Clamp Diode
µA
V
1.0
VIN(0)
Input Resistance
Max. Units
10.5
VDD = 10V
8.5
VDD = 5.0V (See Note)
3.5
VDD = 12V
50
200
VDD = 10V
50
300
VDD = 5.0V
50
600
kΩ
IDD(ON)
VDD = 12V, Outputs Open
3.3
4.5
(One output
VDD = 10V, Outputs Open
3.1
4.5
active)
VDD = 5.0V, Outputs Open
2.4
3.6
IDD(ON)
VDD = 12V, Outputs Open
6.4
10.0
(All outputs
VDD = 10V, Outputs Open
6.0
9.0
active)
VDD = 5.0V, Outputs Open
4.7
7.5
IDD(OFF)
VDD = 12V, Outputs Open, Inputs = 0V
3.0
4.5
(Total)
VDD = 5.0V, Outputs Open, Inputs = 0V
2.2
3.6
IR
VR = 80V, TA = +25°C
50
VR = 80V, TA = +70°C
100
Leakage Current
Overcurrent Threshold
ILIM
Per Output
Start-Up Voltage
VSU
Note 2.
Minimum Operating VDD
VDD MIN
Clamp Diode Forward Voltage
VF
V
500
3.5
3.0
IF = 350mA
4.0
mA
mA
mA
µA
mA
4.5
V
3.5
4.0
V
1.7
2.0
V
Thermal Shutdown
165
°C
Thermal Shutdown Hystersis
10
°C
NOTE 1:
NOTE 2:
NOTE 3:
Operation of these devices with standard TTL or DTL may require the use of appropriate pull-up resistors to insure a minimum logic “1”.
Under-Voltage Lockout is guaranteed to release device at no more than 4.5V, and disable the device at no less than 3.0V.
Specification for packaged product only.
Truth Table
Output
Information present at an input is transferred to its latch when
the STROBE is high. A high CLEAR input will set all latches
to the output OFF condition regardless of the Data or STROBE
input levels. A high OUTPUT ENABLE will set all outputs to
the OFF condition, regardless of any other input conditions.
When the OUTPUT ENABLE is low, the outputs depend on
the state of their respective latches. If current shutdown is
activated, the OUTPUT ENABLE must be pulsed high to
restore operation. Over temperature faults are not latched
and require no reset pulse.
OUTN
INN
Strobe
Clear
Enable
t–1
t
0
1
0
0
X
OFF
1
1
0
0
X
ON
X
X
1
X
X
OFF
X
X
X
1
X
OFF
X
0
0
0
ON
ON
X
0
0
0
OFF
OFF
X = Irrelevant
t–1 = previous output state
t = present output state
October 1998
3
MIC58P01
MIC58P01
Micrel
CLEAR
F
STROBE
C
A
OUTPUT
ENABLE
C
B
B
C
A
G
B
G
IN N
D
E
E
OUT N
Timing Conditions
(TA
A.
B.
C.
D.
E.
F.
G.
= +25°C, Logic Levels are VDD and Ground, VDD = 5V)
Minimum data active time before strobe enabled (data set-up time) ....................................................................... 50ns
Minimum data active time after strobe disabled (data hold time) ............................................................................. 50ns
Minimum strobe pulse width .................................................................................................................................. 125 ns
Typical time between strobe activation and output on to off transition ................................................................... 500ns
Typical time between strobe activation and output off to on transition ................................................................... 500ns
Minimum clear pulse width ..................................................................................................................................... 300ns
Minimum data pulse width ..................................................................................................................................... 225 ns
VDD = 5V to 12V
IL = 100mA
0
50
100
TEMPERATURE (°C)
6
Current Shutdown
Threshold vs. Temperature
SUPPLY CURRENT (mA)
SHUTDOWN THRESHOLD (A)
VDD = 5V
0.50
0.45
VDD = 12V
0.40
0.35
–50
MIC58P01
0
50
100
TEMPERATURE (°C)
150
VDD = 5V
3
2
ALL OUTPUTS OFF
1
8
0.60
ALL OUTPUTS ON
4
0
–50
150
0.55
5
CURRENT SHUTDOWN DELAY (µS)
0.7
0.6
–50
IL = 350mA
Supply Current
vs. Temperature
0
50
100
TEMPERATURE (°C)
150
Supply Current
vs. Temperature
7
6
ALL OUTPUTS ON
VDD = 12V
4
3
ALL OUTPUTS OFF
1
0
–50
Current Shutdown
Delay vs. Output Current
6
5
4
3
VDD = 5V
2
1
VDD = 12V
0
0.4
240
5
2
7
260
OUTPUT DELAY (nS)
1.6
1.5
1.4
1.3
1.2
1.1
1
0.9
0.8
Output Saturation
Voltage vs. Temperature
SUPPLY CURRENT (mA)
SATURATION VOLTAGE (V)
Typical Characteristic Curves
0.5
0.6
0.7
0.8
OUTPUT CURRENT (A)
0.9
Output Delay
vs. Supply Voltage
RL = 50Ω
220
200
180
TD OFF
160
140
TD ON
120
0
50
100
TEMPERATURE (°C)
4
150
100
5 6 7 8 9 10 11 12 13 14 15
SUPPLY VOLTAGE (V)
October 1998
MIC58P01
Micrel
Typical Application
+12V
+5V
0.1µ
22µ
+
1
22
STROBE
2
21
INPUT 1
3
20
INPUT 2
4
19
INPUT 3
5
18
INPUT 4
6
INPUT 5
7
INPUT 6
8
15
INPUT 7
9
14
INPUT 8
10
13
11
12
K1
K2
K3
LATCHES
K4
17
K5
16
K6
K7
K8
Relays: Guardian Electric 1725-1C-12D
MIC58P01 Protected Relay Driver
October 1998
5
MIC58P01
MIC58P01
Micrel
Package Information
1.050
1.120
22
12
0.390
0.300
INDEX AREA
1
11
.065
.035
.200
MAX
.015
MIN
.014
.008
SEATING PLANE .100
MIN
.410
Max
.023
.015
.100 ±.010
22-Pin Plastic DIP (N)
PIN 1
DIMENSIONS:
INCHES (MM)
0.301 (7.645)
0.297 (7.544)
0.027 (0.686)
0.031 (0.787)
0.094 (2.388)
0.090 (2.286)
0.050 (1.270)
TYP
0.016 (0.046)
TYP
0.609 (15.469)
0.605 (15.367)
0.103 (2.616)
0.099 (2.515)
7°
TYP
0.015
R
(0.381)
0.015
(0.381)
SEATING MIN
PLANE
0.297 (7.544)
0.293 (7.442)
0.330 (8.382)
0.326 (8.280)
0.022 (0.559)
0.018 (0.457)
5°
TYP
10° TYP
0.032 (0.813) TYP
0.408 (10.363)
0.404 (10.262)
24-Pin Wide SOP (WM)
MIC58P01
6
October 1998
MIC58P01
Micrel
TOP VIEW
0.045
0.045
0.050
DETAIL A
0.080
0.110
0.027
0.030 DIA
x 0.015 R DEPTH
0.018
DIMENSIONS:
INCHES
0.451 ±0.003
0.490 ±0.020
SIDE VIEW
BOTTOM VIEW
DETAIL A
0.035 R
±0.015
0.410 ±.015
0.300
0.045 x 45°
0.12 DIA
x 0.003~0.004
0.170
0.110
28-Pin PLCC (V)
October 1998
7
MIC58P01
MIC58P01
Micrel
MICREL INC. 1849 FORTUNE DRIVE SAN JOSE, CA 95131
TEL
+ 1 (408) 944-0800
FAX
+ 1 (408) 944-0970
WEB
USA
http://www.micrel.com
This information is believed to be accurate and reliable, however no responsibility is assumed by Micrel for its use nor for any infringement of patents or
other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent right of Micrel Inc.
© 1998 Micrel Incorporated
MIC58P01
8
October 1998