ONSEMI NB4N121KMNR2G

NB4N121K
3.3V Differential In 1:21
Differential Fanout Clock
Driver with HCSL level
Output
http://onsemi.com
Description
The NB4N121K is a Clock differential input fanout distribution 1 to
21 HCSL level differential outputs, optimized for ultra low
propagation delay variation. The NB4N121K is designed with HCSL
clock distribution for FBDIMM applications in mind.
Inputs can accept differential LVPECL, CML, or LVDS levels.
Single-ended LVPECL, CML, LVCMOS or LVTTL levels are
accepted with the proper VREFAC supply (see Figures 5, 10, 11, 12,
and 13). Clock input pins incorporate an internal 50 W on die
termination resistors.
Output drive current at IREF (Pin 1) for 1X load is selected by
connecting to GND. To drive a 2X load, connect IREF to VCC. See
Figure 9.
The NB4N121K specifically guarantees low output–to–output
skews. Optimal design, layout, and processing minimize skew within
a device and from device to device. System designers can take
advantage of the NB4N121K's performance to distribute low skew
clocks across the backplane or the motherboard.
QFN-52
MN SUFFIX
CASE 485M
1
52
MARKING DIAGRAM*
52
1
NB4N
121K
AWLYYWWG
A
WL
YY
WW
G
Features
•Typical Input Clock Frequency 100, 133, 166, 200, 266, 333 and
= Assembly Site
= Wafer Lot
= Year
= Work Week
= Pb-Free Package
400 MHz
•340 ps Typical Rise and Fall Times
•800 ps Typical Propagation Delay
•Dtpd 100 ps Maximum Propagation Delay Variation Per Each
Differential Pair
•<1 ps RMS Additive Clock jitter
•Operating Range: VCC = 3.0 V to 3.6 V with VEE = 0 V
•Differential HCSL Output Level (700 mV Peak-to-Peak)
•Pb-Free Packages are Available*
*For additional marking information, refer to
Application Note AND8002/D.
Q0
Q0
VTCLK
Q1
Q1
CLK
CLK
Q19
Q19
VTCLK
Q20
VCC
GND
*For additional information on our Pb-Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
RREF
IREF
Q20
Figure 1. Pin Configuration (Top View)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 9 of this data sheet.
© Semiconductor Components Industries, LLC, 2007
June, 2007 - Rev. 0
1
Publication Order Number:
NB4N121K/D
VCC
Q0
Q0
Q1
Q1
Q2
Q2
Q3
Q3
Q4
Q4
Q5
Q5
52
51
50
49
48
47
46
45
44
43
42
41
40
NB4N121K
Exposed Pad (EP)
IREF
1
39
VCC
GND
2
38
Q6
VTCLK
3
37
Q6
CLK
4
36
Q7
CLK
5
35
Q7
VTCLK
6
34
Q8
VCC
7
33
Q8
Q20
8
32
Q9
Q20
9
31
Q9
Q19
10
30
Q10
Q19
11
29
Q10
Q18
12
28
Q11
Q18
13
27
Q11
18
19
20
21
22
23
24
25
Q15
Q15
Q14
Q14
Q13
Q13
Q12
Q12
26
17
Q16
VCC
16
15
Q17
Q16
14
Q17
NB4N121K
Figure 2. Pinout Configuration (Top View)
Table 1. PIN DESCRIPTION
Pin
Name
I/O
Description
1
IREF
Output
2
GND
-
Supply Ground. GND pin must be externally connected to power supply
to guarantee proper operation.
3, 6
VTCLK,
VTCLK
-
Internal 50 W Termination Resistor connection Pins. In the differential
configuration when the input termination pins are connected to the com‐
mon termination voltage, and if no signal is applied then the device may
be susceptible to self-oscillation.
4
CLK
LVPECL Input
CLOCK Input (TRUE)
5
CLK
LVPECL Input
CLOCK Input (INVERT)
7, 26, 39, 52
VCC
-
8, 10, 12, 14, 16, 18, 20, 22,
24, 27, 29, 31, 33, 35, 37, 40,
42, 44, 46, 48, 50
Q[20-0]
HCSL Output
Output (INVERT)
9, 11, 13, 15, 17, 19, 21, 23,
25, 28, 30, 32, 34, 36, 38, 41,
43, 45, 47, 49, 51
Q[20-0]
HCSL Output
Output (TRUE)
Exposed Pad
EP
GND
Output current programming pin to select load drive. For 1X
configuration, connect IREF to GND, or for 2X configuration, connect
IREF to VCC (See Figure 9).
Positive Supply pins. VCC pins must be externally connected to a power
supply to guarantee proper operation.
Exposed Pad. The thermally exposed pad (EP) on package bottom (see
case drawing) must be attached to a sufficient heat-sinking conduit for
proper thermal operation. (Note 1)
1. The exposed pad must be connected to the circuit board ground.
http://onsemi.com
2
NB4N121K
Table 2. ATTRIBUTES
Characteristic
Value
Input Default State Resistors
None
ESD Protection
Human Body Model
Moisture Sensitivity (Note 2)
>2 kV
QFN-52
Flammability Rating Oxygen Index: 28 to 34
Level 3
UL 94 V-0 @ 0.125 in
Transistor Count
622
Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test
2. For additional information, see Application Note AND8003/D.
Table 3. MAXIMUM RATINGS (Note 3)
Symbol
Parameter
Condition 1
Rating
Unit
GND = 0 V
6
V
GND = 0 V
GND - 0.3 v VI v VCC
V
1.2
V
50
100
mA
mA
VCC
Positive Power Supply
VI
Positive Input
VINPP
Differential Input Voltage
IOUT
Output Current
Continuous
Surge
TA
Operating Temperature Range
QFN-52
Tstg
Storage Temperature Range
qJA
Thermal Resistance (Junction-to-Ambient) (Note 3)
0 lfpm
500 lfpm
qJC
Thermal Resistance (Junction-to-Case)
2S2P (Note 4)
Tsol
Wave Solder
Condition 2
|CLK - CLKb|
Pb-Free
-40 to +70
°C
-65 to +150
°C
QFN-52
QFN-52
25
19.6
°C/W
°C/W
QFN-52
21
°C/W
265
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
3. JEDEC standard 51-6, multilayer board - 2S2P (2 signal, 2 power).
4. JEDEC standard multilayer board - 2S2P (2 signal, 2 power) with 8 filled thermal vias under exposed pad.
http://onsemi.com
3
NB4N121K
Table 4. DC CHARACTERISTICS (VCC = 3.0 V to 3.6 V, TA = -40°C to +70°C Note 5)
Symbol
Characteristic
IGND
GND Supply Current (All Outputs Loaded)
ICC
Power Supply Current (All Outputs Loaded)
IIH
Input HIGH Current CLKx, CLKx
IIL
Input LOW Current CLKx, CLKx
Min
Typ
Max
Unit
70
98
120
mA
1X
2X
420
780
2.0
-150
mA
150
mA
mA
-2.0
DIFFERENTIAL INPUT DRIVEN SINGLE-ENDED (Figures 5 and 7)
Vth
Input Threshold Reference Voltage Range (Note 6)
VIH
VIL
1050
VCC - 150
mV
Single-Ended Input HIGH Voltage
Vth + 150
VCC
mV
Single-Ended Input LOW Voltage
GND
Vth - 150
mV
DIFFERENTIAL INPUTS DRIVEN DIFFERENTIALLY (Figures 6 and 8)
VIHD
Differential Input HIGH Voltage
1200
VCC
mV
VILD
Differential Input LOW Voltage
GND
VCC - 75
mV
VID
Differential Input Voltage (VIHD - VILD)
75
2400
mV
VCMR
Input Common Mode Range
1163
VCC - 75
HCSL OUTPUTS (Figure 4)
VOH
Output HIGH Voltage
600
740
900
mV
VOL
Output LOW Voltage
-150
0
150
mV
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
5. Input parameters vary 1:1 with VCC. Measurements taken with outputs in either 1X (all outputs loaded 50 W to GND) or 2X (all outputs loaded
25 W to GND) configuration, see Figure 9. For 1X configuration, connect IREF to GND, or for 2X configuration, connect IREF to VCC.
6. Vth is applied to the complementary input when operating in single ended mode.
http://onsemi.com
4
NB4N121K
Table 5. AC CHARACTERISTICS VCC = 3.0 V to 3.6 V, GND = 0 V; -40°C to +70°C (Note 7)
Symbol
Characteristic
Typ
Max
Unit
725
725
725
900
900
900
mV
800
950
ps
Propagation Delay Variations Variation Per Each Diff Pair CLK/CLK to Qx/Qx (Note 8)
(See Figure 3)
100
ps
tSKEW
Duty Cycle Skew (Note 9)
Within-Device Skew, 1X Mode Only (Note 10)
Within-Device Skew, 2X Mode (Note 10)
Device-to-Device Skew (Note 10)
20
50
80
150
ps
ps
ps
ps
tJITTER
RMS Random Clock Jitter (Note 11)
1
ps
VINPP
Input Voltage Swing/Sensitivity
(Differential Configuration)
150
1200
mV
Vcross
Absolute Crossing Magnitude Voltage
250
550
mV
DVcross
Variation in Magnitude of Vcross
150
mV
tr, tf
Absolute Magnitude in Output Risetime and Falltime
(From 175 mV to 525 mV)
Qx, Qx
700
ps
Dtr, Dtf
Variation in Magnitude of Risetime and Falltime (Single-Ended)
(See Figure 4)
Qx, Qx
VOUTPP
Output Voltage Amplitude (@ VINPPmin)
tPLH,
tPHL
Propagation Delay to (See Figure 3)
DtPLH,
DtPHL
Min
fin = 133 MHz
fin = 166 MHz
fin = 200 MHz
CLK/CLK to Qx/Qx
550
fin =133 MHz
fin = 166 MHz
fin = 200 MHz
175
340
1X
2X
ps
125
150
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
7. Measured by forcing VINPP (MIN) from a 50% duty cycle clock source. Measurements taken with outputs in either 1X (all outputs loaded 50 W
to GND) or 2X (all outputs loaded 25 W to GND) configuration, see Figure 9. For 1X configuration, connect IREF to GND, or for 2X
configuration, connect IREF to VCC. Typical gain is 20 dB.
8. Measured from the input pair crosspoint to each single output pair crosspoint across temp and voltage ranges.
9. Duty cycle skew is measured between differential outputs using the deviations of the sum of Tpw- and Tpw+.
10. Skew is measured between outputs under identical transition @ 133 MHz.
11. Additive RMS jitter with 50% duty cycle clock signal using phase noise integrated from 12 KHz to 33 MHz
CLK
VINPP = VIH(CLK) - VIL(CLK)
= VIH(CLK) - VIL(CLK)
CLK
tPLH
tPHL
Q
VOUTPP = VOH(Q) - VOL(Q)
= VOH(Q) - VOL(Q)
Q
DtPLH
DtPHL
Figure 3. AC Reference Measurement
http://onsemi.com
5
NB4N121K
525 mV
DVCROSS
VCROSS
175 mV
tr
tf
Figure 4. HCSL Output Parameter Characteristics
CLK
CLK
CLK
CLK
Vth
Vth
Figure 5. Differential Input Driven
Single-Ended (Vth = VREFAC)
VCC
Vthmax
Figure 6. Differential Inputs Driven
Differentially
VCC
VCMmax
VIHmax
Vth
Vthmin
GND
VIH
Vth
VIL
VIHDmax
VILDmax
VID = VIHD - VILD
VIHDtyp
VILmax
VCMR
VILDtyp
VIHmin
VCMmin
VILmin
GND
Figure 7. Vth Diagram
VIHDmin
VILDmin
Figure 8. VCMR Diagram
http://onsemi.com
6
NB4N121K
RS1C
Qx
1X Load
Z0 = 50 W
Receiver
HCSL
Driver
RS2C
Z0 = 50 W
Qx
RL1B
50
RL2B
50
CL1D
2 pF
CL2D
2 pF
RREFA
2X Load Option
A. For 1X configuration, connect IREF pin
to GND or for 2X configuration, connect
IREF pin to VCC. To adjust load drive for
1X configuration, use RREF from 0 W to
1 kW, to adjust 2X load, use 20 kW to
50 kW.
B. RL1, RL2: 50 W for 1X Load
25 W for 2X Load
C. RS1, RS2: 0 W for Test and
Evaluation. Select to Minimizing Ringing.
D. CL1, CL2, CL3, CL4: Receiver Input
Simulation Load Capacitance Only
Receiver 2
CL3D
2 pF
CL4D
2 pF
Figure 9. Typical Termination Configuration for Output Driver and Device Evaluation
CLx for Test Only (Representing Receiver Input Loading); Not Added to Application
VCC = 3.3 V
VCC = 3.3 V
Z0 = 50 W
LVPECL
Driver
VCC = 3.3 V
Z0 = 50 W
NB4N121K
D
50 W*
VTD
LVDS
Driver
VTD
Z0 = 50 W
50 W*
D
NB4N121K
D
50 W*
VTD
VTD
Z0 = 50 W
VTD = VTD = VCC - 2.0 V
GND
VCC = 3.3 V
50 W*
D
VTD = VTD
GND
GND
GND
*RTIN, Internal Input Termination Resistor
*RTIN, Internal Input Termination Resistor
Figure 10. LVPECL Interface
Figure 11. LVDS Interface
http://onsemi.com
7
NB4N121K
VCC
VCC
Z0 = 50 W
VCC
CML
Driver
VCC
Z0 = 50 W
NB4N121K
D
50 W*
VTD
50 W*
D
NB4N121K
D
50 W*
VTD
LVCMOS/‐
LVTTL
Driver
VTD
Z0 = 50 W
VCC
VTD
50 W*
D
1.5 kW**
VTD = VTD = VCC
GND
GND
GND
GND
GND
VTD = OPEN
D = GND
*RTIN, Internal Input Termination Resistor
*RTIN, Internal Input Termination Resistor
**or VREFAC
Figure 12. Standard 50 W Load CML Interface
Figure 13. LVCMOS/LVTTL Interface
VCC
VDR
INTQb
INTQ
Q
Qb
Figure 14. HCSL Output Structure
http://onsemi.com
8
NB4N121K
ORDERING INFORMATION
Package
Shipping†
QFN-52
260 Units / Tray
NB4N121KMNG
QFN-52
(Pb-Free)
260 Units / Tray
NB4N121KMNR2
QFN-52
2000 / Tape & Reel
QFN-52
(Pb-Free)
2000 / Tape & Reel
Device
NB4N121KMN
NB4N121KMNR2G
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
9
NB4N121K
PACKAGE DIMENSIONS
52 PIN QFN 8x8
CASE 485M-01
ISSUE A
D
A
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION:
MILLIMETERS
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED
BETWEEN 0.25 AND 0.30 MM FROM
TERMINAL.
4. COPLANARITY APPLIES TO THE
EXPOSED PAD AS WELL AS THE
TERMINALS.
B
E
DIM
A
A1
A2
A3
b
D
D2
E
E2
e
K
L
2X
0.15 C
2X
0.15 C
A2
0.10 C
A
0.08 C
A3
A1
MILLIMETERS
MIN
MAX
0.80
1.00
0.00
0.05
0.60
0.80
0.20 REF
0.18
0.30
8.00 BSC
6.50
6.80
8.00 BSC
6.50
6.80
0.50 BSC
0.20
--0.30
0.50
REF
SEATING PLANE
C
D2
14
26
27
13
52 X
L
E2
39
1
52 X
K
52
40
e
52 X
b
NOTE 3
0.10 C A B
0.05 C
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada
Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800-282-9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81-3-5773-3850
http://onsemi.com
10
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NB4N121K/D