AD OP275GSR

a
FEATURES
Excellent Sonic Characteristics
Low Noise: 6 nV/√Hz
Low Distortion: 0.0006%
High Slew Rate: 22 V/␮s
Wide Bandwidth: 9 MHz
Low Supply Current: 5 mA
Low Offset Voltage: 1 mV
Low Offset Current: 2 nA
Unity Gain Stable
SOIC-8 Package
Dual Bipolar/JFET, Audio
Operational Amplifier
OP275*
PIN CONNECTIONS
8-Lead Narrow-Body SO
(S Suffix)
OUT A 1
8
V+
–IN A 2
7
OUT B
6
–IN B
5
+IN B
+IN A 3
V– 4
OP275
8-Lead Epoxy DIP
(P Suffix)
OP275
8
V+
2
7
OUT B
3
6
–IN B
4
5
+IN B
OUT A
1
–IN A
+IN A
V–
APPLICATIONS
High Performance Audio
Active Filters
Fast Amplifiers
Integrators
GENERAL DESCRIPTION
The OP275 is the first amplifier to feature the Butler Amplifier
front-end. This new front-end design combines both bipolar
and JFET transistors to attain amplifiers with the accuracy and
low noise performance of bipolar transistors, and the speed and
sound quality of JFETs. Total Harmonic Distortion plus Noise
equals that of previous audio amplifiers, but at much lower supply currents.
A very low l/f corner of below 6 Hz maintains a flat noise density
response. Whether noise is measured at either 30 Hz or 1 kHz,
it is only 6 nV/√Hz. The JFET portion of the input stage gives
the OP275 its high slew rates to keep distortion low, even when
large output swings are required, and the 22 V/µs slew rate of
the OP275 is the fastest of any standard audio amplifier. Best of
all, this low noise and high speed are accomplished using less
than 5 mA of supply current, lower than any standard audio
amplifier.
Improved dc performance is also provided with bias and offset
currents greatly reduced over purely bipolar designs. Input offset voltage is guaranteed at 1 mV and is typically less than
200 µV. This allows the OP275 to be used in many dc coupled
or summing applications without the need for special selections
or the added noise of additional offset adjustment circuitry.
The output is capable of driving 600 Ω loads to 10 V rms while
maintaining low distortion. THD + Noise at 3 V rms is a low
0.0006%.
The OP275 is specified over the extended industrial (–40°C to
+85°C) temperature range. OP275s are available in both plastic
DIP and SOIC-8 packages. SOIC-8 packages are available in
2500 piece reels. Many audio amplifiers are not offered in
SOIC-8 surface mount packages for a variety of reasons; however, the OP275 was designed so that it would offer full performance in surface mount packaging.
*Protected by U.S. Patent No. 5,101,126.
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
© Analog Devices, Inc., 1995
One Technology Way, P.O. Box 9106, Norwood. MA 02062-9106, U.S.A.
Tel: 617/329-4700
Fax: 617/326-8703
OP275–SPECIFICATIONS
ELECTRICAL CHARACTERISTICS (@ V = ⫾15.0 V, T = +25ⴗC unless otherwise noted)
S
Parameter␣
Symbol
AUDIO PERFORMANCE␣
THD + Noise
Voltage Noise Density
en
Current Noise Density
Headroom
in
INPUT CHARACTERISTICS␣
Offset Voltage
VOS
Input Bias Current
IB
Input Offset Current
IOS
Input Voltage Range
Common-Mode Rejection Ratio
VCM
CMRR
Large Signal Voltage Gain
AVO
Offset Voltage Drift
∆VOS/∆T
A
Conditions
Min
VIN = 3 V rms,
RL = 2 kΩ, f = 1 kHz
f = 30 Hz
f = 1 kHz
f = 1 kHz
THD + Noise ≤ 0.01%,
RL = 2 kΩ, VS = ± 18 V
–40°C ≤ TA ≤ +85°C
VCM = 0 V
VCM = 0 V, –40°C ≤ TA ≤ +85°C
VCM = 0 V
VCM = 0 V, –40°C ≤ TA ≤ +85°C
VCM = ± 10.5 V,
–40°C ≤ TA ≤ +85°C
RL = 2 kΩ
RL = 2 kΩ, –40°C ≤ TA ≤ +85°C
RL = 600 Ω
Typ
Units
0.006
7
6
1.5
%
nV/√Hz
nV/√Hz
pA/√Hz
>12.9
dBu
100
100
2
2
–10.5
80
250
175
Max
1
1.25
350
400
50
100
+10.5
106
mV
mV
nA
nA
nA
nA
V
200
2
dB
V/mV
V/mV
V/mV
µV/°C
OUTPUT CHARACTERISTICS␣
Output Voltage Swing
VO
RL = 2 kΩ
RL = 2 kΩ, –40°C ≤ TA ≤ +85°C
RL = 600 Ω, VS = ± 18 V
–13.5
–13
± 13.9
+13.5
± 13.9
+13
+14, –16
V
V
V
POWER SUPPLY␣
Power Supply Rejection Ratio
PSRR
VS = ± 4.5 V to ± 18 V
VS = ± 4.5 V to ± 18 V,
–40°C ≤ TA ≤ +85°C
VS = ± 4.5 V to ± 18 V, VO = 0 V,
RL = ∞, –40°C ≤ TA ≤ +85°C
VS = ± 22 V, VO = 0 V, RL = ∞,
–40°C ≤ TA ≤ +85°C
85
111
dB
Supply Current
Supply Voltage Range
DYNAMIC PERFORMANCE␣
Slew Rate
Full-Power Bandwidth
Gain Bandwidth Product
Phase Margin
Overshoot Factor
ISY
VS
SR
BWP
GBP
øm
RL = 2 kΩ
VIN = 100 mV, AV = +1,
RL = 600 Ω, CL = 100 pF
80
dB
4
± 4.5
15
22
5
mA
5.5
± 22
mA
V
9
62
V/µs
kHz
MHz
Degrees
10
%
Specifications subject to change without notice.
–2–
REV. A
OP275
WAFER TEST LIMITS (@ V = ⴞ15.0 V, T = +25ⴗC unless otherwise noted)
S
A
Parameter
Symbol
Offset Voltage
Input Bias Current
Input Offset Current
Input Voltage Range1
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Large Signal Voltage Gain
Output Voltage Range
Supply Current
VOS
IB
IOS
VCM
CMRR
PSRR
AVO
VO
ISY
Conditions
VCM = 0 V
VCM = 0 V
VCM = ± 10.5 V
V = ± 4.5 V to ± 18 V
RL = 2 kΩ
RL = 10 kΩ
VO = 0 V, RL = ∞
Limit
Units
1
350
50
± 10.5
80
85
250
± 13.5
5
mV max
nA max
nA max
V min
dB min
dB min
V/mV min
V min
mA max
NOTES
Electrical tests and wafer probe to the limits shown. Due to variations in assembly methods and normal yield loss, yield after packaging is not guaranteed for standard
product dice. Consult factory to negotiate specifications based on dice lot qualifications through sample lot assembly and testing.
1
Guaranteed by CMRR test.
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS 1
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 22 V
Input Voltage2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 22 V
Differential Input Voltage2 . . . . . . . . . . . . . . . . . . . . . . . ± 7.5 V
Output Short-Circuit Duration to GND3 . . . . . . . . . Indefinite
Storage Temperature Range
P, S Package . . . . . . . . . . . . . . . . . . . . . . . . –65°C to +150°C
Operating Temperature Range
OP275G . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
Junction Temperature Range
P, S Package . . . . . . . . . . . . . . . . . . . . . . . . –65°C to +150°C
Lead Temperature Range (Soldering, 60 sec) . . . . . . . +300°C
Package Type
θJA4
θJC
Units
8-Pin Plastic DIP (P)
8-Pin SOIC (S)
103
158
43
43
°C/W
°C/W
ORDERING GUIDE
Model
Temperature Range
Package Option
OP275GP
OP275GS
OP275GSR
OP275GBC
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
+25°C
8-Pin Plastic DIP
8-Pin SOIC
SO-8 Reel, 2500 pcs.
DICE
DICE CHARACTERISTICS
NOTES
1
Absolute maximum ratings apply to both DICE and packaged parts, unless
otherwise noted.
2
For supply voltages greater than ± 22 V, the absolute maximum input voltage is
equal to the supply voltage.
3
Shorts to either supply may destroy the device. See data sheet for full details.
4
θJA is specified for the worst case conditions, i.e., θJA is specified for device in socket
for cerdip, P-DIP, and LCC packages; θJA is specified for device soldered in circuit
board for SOIC package.
Die Size 0.070 × 0.108 in. (7,560 sq. mils)
Substrate is connected to V–
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the OP275 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
REV. A
–3–
WARNING!
ESD SENSITIVE DEVICE
OP275–Typical Performance Curves
1500
1250
+VOM
10
5
0
–5
–10
–VOM
–15
VS = ±15V
VO = ±10V
40
+GAIN
RL = 2kΩ
1000
–GAIN
RL = 2kΩ
750
+GAIN
RL = 600Ω
500
–GAIN
RL = 600Ω
250
–20
–25
0
±5
±10
±15
±20
SUPPLY VOLTAGE – V
0
–50
±25
Output Voltage Swing vs. Supply
Voltage
–25
0
25
50
TEMPERATURE – °C
75
90
10
45
0
–90
–30
–135
–40
–180
10k
135
20
90
MARKER 15 309.058Hz
PHASE (A/R
90.606Deg
45
0
0
–10
–45
–20
–90
10k
100k
1M
Closed-Loop Gain and Phase, AV = +1
20
AVCL = +10
10
0
AVCL = +1
POWER SUPPLY REJECTION – dB
80
60
40
20
1k
10k
100k
FREQUENCY – Hz
1M
Common-Mode Rejection vs.
Frequency
10M
AVCL = +1
40
AVCL = +10
30
AVCL = +100
20
10
10k
100k
1M
10M
FREQUENCY – Hz
0
100
100M
1k
10k
100k
FREQUENCY – Hz
1M
10M
Closed-Loop Output Impedance vs.
Frequency
100
120
100
VS = ±15V
TA = +25°C
–10
Closed-Loop Gain vs. Frequency
120
COMMON-MODE REJECTION – dB
50
30
FREQUENCY – Hz
0
100
VS = ±15V
TA = +25°C
AVCL = +100
–30
1k
VS = ±15V
TA = +25°C
10M
–20
10M
Open-Loop Gain, Phase vs. Frequency
1M
FREQUENCY – Hz
80
100
GAIN
+PSRR
OPEN-LOOP GAIN – dB
10
PHASE – Degrees
GAIN – dB
30
100k
60
40
40
–45
–20
IMPEDANCE – Ω
VS = ±15V
TA = +25°C
50
0
–10
100
Open-Loop Gain vs. Temperature
CLOSED-LOOP GAIN – dB
MARKER 15 309.059Hz
MAG (A/H)
60.115dB
135
20
50
60
180
VS = ±15V
TA = +25°C
30
80
VS = ±15V
TA = +25°C
60
–PSRR
40
20
0
10
100
1k
10k
100k
FREQUENCY – Hz
Power Supply Rejection vs.
Frequency
–4–
1M
60
40
PHASE
VS = ±15V
RL = 2kΩ
TA = +25°C
0
45
Ø m = 58°
90
20
135
0
180
–20
225
–40
270
–60
1k
10k
100k
1M
10M
FREQUENCY – Hz
PHASE – Degrees
15
OPEN-LOOP GAIN – V/mV
OUTPUT VOLTAGE SWING – V
20
PHASE – Degrees
TA = +25°C
RL = 2kΩ
GAIN – dB
25
100M
Open-Loop Gain, Phase vs. Frequency
REV. A
OP275
100
60
Øm
9
55
GBW
8
50
80
60
AVCL = +1
POSITIVE EDGE
50
40
VS = ±15V
RL = 2kΩ
VIN = 100mV p-p
30
20
–25
0
25
50
TEMPERATURE – °C
75
0
0
200
300
400
100
LOAD CAPACITANCE – pF
ABSOLUTE OUTPUT CURRENT – mA
SUPPLY CURRENT – mA
TA = +25°C
VS = ±15V
AVCL = +1
RL = 2kΩ
10
4.5
TA = +85°C
TA = +25°C
4.0
TA = –40°C
3.5
5
10k
100k
1M
FREQUENCY – Hz
10M
Maximum Output Swing vs.
Frequency
3.0
CURRENT NOISE DENSITY – pA/ Hz
250
200
150
100
50
TA = +25°C
VS = ±15V
1k
LOAD RESISTANCE – Ω
10k
±5
90
SINK
80
70
60
50
40
SOURCE
30
20
–50
±25
±10
±15
±20
SUPPLY VOLTAGE – V
VS = ±15V
–25
0
25
50
TEMPERATURE – °C
75
100
Short Circuit Current vs. Temperature
500
VS = ±15V
–40°C to +85°C
VS = ±15V
TA = +25°C
4
400
3
300
BASED ON 920 OP AMPS
2
200
1
100
0
–25
0
25
50
TEMPERATURE – °C
75
100
Input Bias Current vs. Temperature
REV. A
4
100
5
VS = ±15V
0
–50
0
Supply Current vs. Supply Voltage
300
+VOM
6
110
UNITS
0
1k
8
120
25
15
10
Maximum Output Voltage vs. Load
Resistance
5.0
20
–VOM
12
0
100
500
Small-Signal Overshoot vs. Load
Capacitance
30
14
2
10
40
100
Gain Bandwidth Product, Phase
Margin vs. Temperature
MAXIMUM OUTPUT SWING – V
70
OVERSHOOT – %
10
7
–50
INPUT BIAS CURRENT – nA
16
AVCL = +1
NEGATIVE EDGE
90
MAXIMUM OUTPUT SWING – V
65
PHASE MARGIN – Degrees
GAIN BANDWIDTH PRODUCT – MHz
11
10
100
1k
FREQUENCY – Hz
100k
Current Noise Density vs. Frequency
–5–
0
1
2
3
4
5
6 7
TCVOS – µV/°C
TCVOS Distribution
8
9
10
OP275–Typical Performance Curves
50
10
200
VS = ±15V
TA = +25°C
BASED ON 920 OP AMPS
TA = +25°C
VS = ±15V
8
45
6
160
+0.1%
+0.01%
UNITS
120
80
SLEW RATE – V/µs
STEP SIZE – V
4
2
0
–2
–4
–0.1%
40
–0.01%
–6
40
35
–SR
30
+SR
25
–8
0
–500–400–300–200–100 0 100 200 300 400 500
INPUT OFFSET VOLTAGE – µV
–10
20
0
100 200 300 400 500 600 700 800 900
SETTLING TIME – ns
50
35
VS = ±15V
RL = 2kΩ
30
TA = +25°C
VS = ±15V
RL = 2kΩ
45
SLEW RATE – V/µs
SLEW RATE – V/µs
40
500
Slew Rate vs. Capacitive Load
Settling Time vs. Step Size
Input Offset (VOS) Distribution
200
300
400
100
CAPACITIVE LOAD – pF
0
25
20
15
10
–SR
40
35
30
+SR
25
5
0
0
.2
.4
.6
.8
20
–50
1.0
–25
DIFFERENTIAL INPUT VOLTAGE – V
75
100
Slew Rate vs. Temperature
Slew Rate vs. Differential Input Voltage
100
90
0
25
50
TEMPERATURE – °C
100
90
10
10
0%
0%
5V
200ns
5V
Negative Slew Rate
RL = 2 kΩ, VS = ± 15 V, AV = +1
200ns
Positive Slew Rate
RL = 2 kΩ, VS = ± 15 V, AV = +1
CH A: 80.0 µV FS
MKR: 6.23 nV/√Hz
10.0 µV/DIV
100
90
10
0%
50mV
100ns
0 Hz
MKR:
Small Signal Response
RL = 2 kΩ, VS = ± 15 V, AV = +1
1 000 Hz
2.5 kHz
BW: 15.0 MHz
Voltage Noise Density vs. Frequency
VS = ± 15 V
–6–
REV. A
OP275
APPLICATIONS
Short Circuit Protection
THD + NOISE – %
0.010
The OP275 has been designed with inherent short circuit protection to ground. An internal 30 Ω resistor, in series with the
output, limits the output current at room temperature to ISC +
= 40 mA and ISC– = –90 mA, typically, with ± 15 V supplies.
However, shorts to either supply may destroy the device when
excessive voltages or currents are applied. If it is possible for a
user to short an output to a supply, for safe operation, the output current of the OP275 should be design-limited to ± 30 mA,
as shown in Figure 1.
RFB
10
OUTPUT SWING – V rms
The output of the OP275 is designed to maintain low harmonic
distortion while driving 600 Ω loads. However, driving 600 Ω
loads with very high output swings results in higher distortion if
clipping occurs. A common example of this is in attempting to
drive 10 V rms into any load with ± 15 volt supplies. Clipping
will occur and distortion will be very high.
To attain low harmonic distortion with large output swings,
supply voltages may be increased. Figure 5 shows the performance of the OP275 driving 600␣ Ω loads with supply voltages
varying from ± 18 volts to ± 20 volts. Notice that with ± 18 volt
supplies the distortion is fairly high, while with ± 20 volt supplies
it is a very low 0.0007%.
0.0001
FEEDBACK
VOUT
A1
0.001
A1 = 1/2 OP275
THD – %
Figure 1. Recommended Output Short Circuit Protection
0.010
THD + NOISE – %
RL = 600Ω, 2k, 10k
VS = ±15V
VIN = 3V rms
AV = +1
RL = 600Ω
VOUT = 10 Vrms @ 1kHz
0.01
0.1
0
±17
0.001
0.0005
100
1
Figure 4. Headroom, THD + Noise vs. Output Amplitude
(V rms); RLOAD = 600 Ω, VSUP = ± 18 V
Total Harmonic Distortion + Noise (THD + N) of the OP275
is well below 0.001% with any load down to 600 Ω. However,
this is dependent upon the peak output swing. In Figure 2 it is
seen that the THD + Noise with 3 V rms output is below
0.001%. In the following Figure 3, THD + Noise is below
0.001% for the 10 kΩ and 2 kΩ loads but increases to above
0.1% for the 600␣ Ω load condition. This is a result of the output
swing capability of the OP275. Notice the results in Figure 4,
showing THD vs. VIN (V rms). This figure shows that the THD
+ Noise remains very low until the output reaches 9.5 volts rms.
This performance is similar to competitive products.
20
0.001
0.0001
0.5
Total Harmonic Distortion
RX
332Ω
VS = ±18V
RL = 600Ω
1k
10k
±18
±19
±20
SUPPLY VOLTAGE – V
±21
±22
Figure 5. THD + Noise vs. Supply Voltage
20k
FREQUENCY – Hz
Noise
Figure 2. THD + Noise vs. Frequency vs. RLOAD
The voltage noise density of the OP275 is below 7 nV/√Hz from
30 Hz. This enables low noise designs to have good performance throughout the full audio range. Figure 6 shows a typical
OP275 with a 1/f corner at 2.24 Hz.
THD + NOISE – %
1
600Ω
0.1
AV = +1
VS = ±18V
VIN = 10V rms
80kHz FILTER
0.010
CH A: 80.0 µV FS
MKR: 45.6 µV/√Hz
10.0 µV/DIV
2k
0.001
10k
0.0001
20
100
1k
10k
20k
FREQUENCY – Hz
Figure 3. THD + Noise vs. RLOAD; VIN =10 V rms,
± 18 V Supplies
0 Hz
MKR:
2.24 Hz
10 Hz
BW: 0.145 Hz
Figure 6. 1/f Noise Corner, VS = ± 15 V, AV = 1000
REV. A
–7–
OP275
this effect from occurring in noninverting applications. For these
applications, the fix is a simple one and is illustrated in Figure 9.
A 3.92 kΩ resistor in series with the noninverting input of the
OP275 cures the problem.
Noise Testing
For audio applications the noise density is usually the most important noise parameter. For characterization the OP275 is
tested using an Audio Precision, System One. The input signal
to the Audio Precision must be amplified enough to measure it
accurately. For the OP275 the noise is gained by approximately
1020 using the circuit shown in Figure 7. Any readings on the
Audio Precision must then be divided by the gain. In implementing this test fixture, good supply bypassing is essential.
RFB*
VOUT
VIN
RL
2kΩ
RS
3.92kΩ
100Ω
909Ω
*RFB IS OPTIONAL
Figure 9. Output Voltage Phase Reversal Fix
A
OP37
OP275
Overload, or Overdrive, Recovery
OP37
Overload, or overdrive, recovery time of an operational amplifier
is the time required for the output voltage to recover to a rated
output voltage from a saturated condition. This recovery time is
important in applications where the amplifier must recover
quickly after a large abnormal transient event. The circuit
shown in Figure 10 was used to evaluate the OP275’s overload
recovery time. The OP275 takes approximately 1.2 µs to recover
to VOUT = +10 V and approximately 1.5 µs to recover to VOUT =
–10 V.
OUTPUT
B
909Ω
4.42kΩ
100Ω
490Ω
909Ω
100Ω
Figure 7. Noise Test Fixture
Input Overcurrent Protection
The maximum input differential voltage that can be applied to
the OP275 is determined by a pair of internal Zener diodes connected across its inputs. They limit the maximum differential input voltage to ± 7.5 V. This is to prevent emitter-base junction
breakdown from occurring in the input stage of the OP275
when very large differential voltages are applied. However, in order to preserve the OP275’s low input noise voltage, internal resistances in series with the inputs were not used to limit the
current in the clamp diodes. In small signal applications, this is
not an issue; however, in applications where large differential
voltages can be inadvertently applied to the device, large transient currents can flow through these diodes. Although these diodes have been designed to carry a current of ± 5 mA, external
resistors as shown in Figure 8 should be used in the event that
the OP275’s differential voltage were to exceed ± 7.5 V.
1.4kΩ 2
R2
10kΩ
2
3
VIN
4V p-p
@100Hz
A1
RS
909Ω
1
VOUT
RL
2.43kΩ
A1 = 1/2 OP275
Figure 10.␣ Overload Recovery Time Test Circuit
Measuring Settling Time
The design of OP275 combines high slew rate and wide gainbandwidth product to produce a fast-settling (tS < 1 µs) amplifier for 8- and 12-bit applications. The test circuit designed to
measure the settling time of the OP275 is shown in Figure 11.
This test method has advantages over false-sum node techniques in that the actual output of the amplifier is measured, instead of an error voltage at the sum node. Common-mode
settling effects are exercised in this circuit in addition to the slew
rate and bandwidth effects measured by the false-sum-node
method. Of course, a reasonably flat-top pulse is required as the
stimulus.
–
OP275
1.4kΩ 3
R1
1kΩ
6
+
Figure 8. Input Overcurrent Protection
Output Voltage Phase Reversal
The output waveform of the OP275 under test is clamped by
Schottky diodes and buffered by the JFET source follower. The
signal is amplified by a factor of ten by the OP260 and then
Schottky-clamped at the output to prevent overloading the
oscilloscope’s input amplifier. The OP41 is configured as a fast
integrator which provides overall dc offset nulling.
Since the OP275’s input stage combines bipolar transistors for
low noise and p-channel JFETs for high speed performance, the
output voltage of the OP275 may exhibit phase reversal if either
of its inputs exceed its negative common-mode input voltage.
This might occur in very severe industrial applications where a
sensor, or system, fault might apply very large voltages on the
inputs of the OP275. Even though the input voltage range of the
OP275 is ± 10.5 V, an input voltage of approximately –13.5 V
will cause output voltage phase reversal. In inverting amplifier
configurations, the OP275’s internal 7.5 V input clamping diodes will prevent phase reversal; however, they will not prevent
High Speed Operation
As with most high speed amplifiers, care should be taken with
supply decoupling, lead dress, and component placement. Recommended circuit configurations for inverting and noninverting
applications are shown in Figures 12 and Figure 13.
–8–
REV. A
OP275
16–20V
–
+
+15V
1kΩ
0.1µF
RL
V+
D3
OUTPUT
(TO SCOPE)
1kΩ
2N4416
DUT
V–
D1
1/2 OP260AJ
1µF
D2
0.1µF
+
D4
RF
2kΩ
10kΩ
–
IC2
10kΩ
16–20V
RG
222Ω
2N2222A
±5V
1N4148
750Ω
15kΩ
SCHOTTKY DIODES D1–D4 ARE
HEWLETT-PACKARD HP5082-2835
IC1 IS 1/2 OP260AJ
IC2 IS PMI OP41EJ
–15V
Figure 11.␣ OP275’s Settling Time Test Fixture
CFB
+15V
0.1µF
RS
2
3
VIN
RFB
10µF
+
CS
CIN
8
1/2
OP275
1
VOUT
VOUT
RL
4 0.1µF
2kΩ
10µF
+
Figure 14. Compensating the Feedback Pole
Attention to Source Impedances Minimizes Distortion
Since the OP275 is a very low distortion amplifier, careful attention should be given to source impedances seen by both inputs.
As with many FET-type amplifiers, the p-channel JFETs in the
OP275’s input stage exhibit a gate-to-source capacitance that
varies with the applied input voltage. In an inverting configuration, the inverting input is held at a virtual ground and, as such,
does not vary with input voltage. Thus, since the gate-to-source
voltage is constant, there is no distortion due to input capacitance modulation. In noninverting applications, however, the
gate-to-source voltage is not constant. The resulting capacitance
modulation can cause distortion above 1 kHz if the input impedance is > 2 kΩ and unbalanced.
–15V
Figure 12. Unity Gain Follower
+15V
10µF
+
0.1µF
10pF
VIN
4.99kΩ
4.99kΩ
2
3
8
1/2
OP275
1
4
VOUT
Figure 15 shows some guidelines for maximizing the distortion
performance of the OP275 in noninverting applications. The
best way to prevent unwanted distortion is to ensure that the
parallel combination of the feedback and gain setting resistors
(R F and RG) is less than 2 kΩ. Keeping the values of these resistors small has the added benefits of reducing the thermal noise
2kΩ
2.49kΩ
0.1µF
10µF
+
–15V
RG
Figure 13. Unity Gain Inverter
In inverting and noninverting applications, the feedback resistance forms a pole with the source resistance and capacitance
(RS and CS) and the OP275’s input capacitance (CIN), as shown
in Figure 14. With RS and RF in the kilohm range, this pole can
create excess phase shift and even oscillation. A small capacitor,
CFB, in parallel and RFB eliminates this problem. By setting RS
(CS + CIN) = RFBCFB, the effect of the feedback pole is completely removed.
REV. A
–9–
RF
RS*
0P275
VOUT
VIN
* RS = RG//RF IF RG//RF > 2kΩ
FOR MINIMUM DISTORTION
Figure 15. Balanced Input Impedance to Minimize
Distortion in Noninverting Amplifier Circuits
OP275
of the circuit and dc offset errors. If the parallel combination of
R F and RG is larger than 2␣ kΩ, then an additional resistor, R S,
should be used in series with the noninverting input. The value
of RS is determined by the parallel combination of RF and RG to
maintain the low distortion performance of the OP275.
Driving Capacitive Loads
importance. Like the transformer based design, either output
can be shorted to ground for unbalanced line driver applications
without changing the circuit gain of 1. Other circuit gains can be
set according to the equation in the diagram. This allows the
design to be easily set to noninverting, inverting, or differential
operation.
The OP275 was designed to drive both resistive loads to 600 Ω
and capacitive loads of over 1000 pF and maintain stability.
While there is a degradation in bandwidth when driving capacitive loads, the designer need not worry about device stability.
The graph in Figure 16 shows the 0 dB bandwidth of the OP275
with capacitive loads from 10 pF to 1000 pF.
10
9
BANDWIDTH – MHz
8
7
6
5
4
3
2
A 3-Pole, 40 kHz Low-Pass Filter
The closely matched and uniform ac characteristics of the
OP275 make it ideal for use in GIC (Generalized Impedance
Converter) and FDNR (Frequency-Dependent Negative Resistor) filter applications. The circuit in Figure 18 illustrates a linear-phase, 3-pole, 40 kHz low-pass filter using an OP275 as an
inductance simulator (gyrator). The circuit uses one OP275 (A2
and A3) for the FDNR and one OP275 (A1 and A4) as an input
buffer and bias current source for A3. Amplifier A4 is configured in a gain of 2 to set the pass band magnitude response to
0 dB. The benefits of this filter topology over classical approaches are that the op amp used in the FDNR is not in the
signal path and that the filter’s performance is relatively insensitive to component variations. Also, the configuration is such that
large signal levels can be handled without overloading any of the
the filter’s internal nodes. As shown in Figure 19, the OP275’s
symmetric slew rate and low distortion produce a clean, wellbehaved transient response.
1
R1
95.3kΩ
0
0
200
400
600
CLOAD – pF
800
1000
2
3
VIN
Figure 16. Bandwidth vs. CLOAD
A1
1
C1
2200pF
R2
787Ω
High Speed, Low Noise Differential Line Driver
The circuit of Figure 17 is a unique line driver widely used in
industrial applications. With ± 18 V supplies, the line driver can
deliver a differential signal of 30 V p-p into a 2.5 kΩ load. The
high slew rate and wide bandwidth of the OP275 combine to
yield a full power bandwidth of 130 kHz while the low noise
front end produces a referred-to-input noise voltage spectral
density of 10 nV/√Hz.
C2
2200pF
2
1
2
3
R1
2k
VIN
3
2
A1
1
3
5
R7
100kΩ
R9
1kΩ
6
A4
7
VOUT
R8
1kΩ
C3
2200pF
A1, A4 = 1/2 OP275
A2, A3 = 1/2 OP275
R9
50
R5
1.82kΩ
VO1
R11
1k
Figure 18. A 3-Pole, 40 kHz Low-Pass Filter
R7
2k
R4
2k
VO2 – VO1 = VIN
1
P1
10k
R2
2k
R5
2k R6
2k
100
90
6
A1 = 1/2 OP275
A2
A3
C4
2200pF
7
R4
1.87kΩ
R3
2k
A2
5
6
R3
1.82kΩ
R6
4.12kΩ
5
A3
A2, A3 = 1/2 OP275
7
R10
50
R12
1k
VOUT
10Vp-p
10kHz
VO2
R8
2k
10
0%
R3
GAIN = R1
SET R2, R4, R5 = R1 AND R6, R7, R8 = R3
SCALE: VERTICAL–2V/ DIV
HORIZONTAL–10µs/ DIV
Figure 17. High Speed, Low Noise Differential Line Driver
The design is a transformerless, balanced transmission system
where output common-mode rejection of noise is of paramount
Figure 19. Low-Pass Filter Transient Response
–10–
REV. A
OP275
OP275 SPICE Model
* POLE/ZERO PAIR AT 1.5 MHz/2.7 MHz
*
R8
21
98
1E-3
R9
21
22
1.25E-3
C4
22
98
47.2E-12
G2
98
21
18
28
1E-3
*
* POLE AT 100 MHz
*
R10
23
98
1
C5
23
98
1.59E-9
G3
98
23
21
28
1
*
* POLE AT 100 MHz
*
R11
24
98
1
C6
24
98
1.59E-9
G4
98
24
23
28
1
*
* COMMON-MODE GAIN NETWORK WITH ZERO AT
1 kHz
*
R12
25
26
1E6
C7
25
26
1.5915E-12
R13
26
98
1
E2
25
98
POLY(2) 1 98 2 98 0 2.50 2.50
*
* POLE AT 100 MHz
*
R14
27
98
1
C8
27
98
1.59E-9
G5
98
27
24
28
1
*
* OUTPUT STAGE
*
R15
28
99
100E3
R16
28
50
100E3
C9
28
50
1E-6
ISY
99
50
1.85E-3
R17
29
99
100
R18
29
50
100
L2
29
34
1E-9
G6
32
50
27
29
10E-3
G7
33
50
29
27
10E-3
G8
29
99
99
27
10E-3
G9
50
29
27
50
10E-3
V4
30
29
1.3
V5
29
31
3.8
F1
29
0
V4
1
F2
0
29
V5
1
D5
27
30
DX
D6
31
27
DX
D7
99
32
DX
D8
99
33
DX
D9
50
32
DY
D10
50
33
DY
*
* MODELS USED
*
.MODEL QX
PNP(BF=5E5)
.MODEL DX
D(IS=1E-12)
.MODEL DY
D(IS=1E-15 BV=50)
.MODEL DZ
D(IS=1E-15 BV=7.0)
.MODEL DEN D(IS=1E-12 RS=4.35K KF=1.95E-15 AF=1)
.MODEL DIN D(IS=1E-12 RS=268 KF=1.08E-15 AF=1)
.ENDS
*
* Node assignments
*
noninverting input
*
inverting input
*
positive supply
*
negative supply
*
output
*
*
.SUBCKT OP275 1
2
99
50 34
*
* INPUT STAGE & POLE AT 100 MHz
*
R3
5
51
2.188
R4
6
51
2.188
CIN 1
2
3.7E-12
CM1 1
98
7.5E-12
CM2 2
98
7.5E-12
C2
5
6
364E-12
I1
97
4
100E-3
IOS
1
2
1E-9
EOS 9
3
POLY(1) 26
28 0.5E-3 1
Q1
5
2
7
QX
Q2
6
9
8
QX
R5
7
4
1.672
R6
8
4
1.672
D1
2
36
DZ
D2
1
36
DZ
EN
3
1
10
0
1
GN1 0
2
13
0
1E-3
GN2 0
1
16
0
1E-3
*
EREF 98
0
28
0
1
EP
97
0
99
0
1
EM
51
0
50
0
1
*
* VOLTAGE NOISE SOURCE
*
DN1 35
10
DEN
DN2 10
11
DEN
VN1 35
0
DC
2
VN2 0
11
DC
2
*
* CURRENT NOISE SOURCE
*
DN3 12
13
DIN
DN4 13
14
DIN
VN3 12
0
DC
2
VN4 0
14
DC
2
*
* CURRENT NOISE SOURCE
*
DN5 15
16
DIN
DN6 16
17
DIN
VN5 15
0
DC
2
VN6 0
17
DC
2
*
* GAIN STAGE & DOMINANT POLE AT 32 Hz
*
R7
18
98
1.09E6
C3
18
98
4.55E-9
G1
98
18
5
6
4.57E-1
V2
97
19
1.35
V3
20
51
1.35
D3
18
19
DX
D4
20
18
DX
*
REV. A
–11–
OP275
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
8-Lead Narrow-Body SOIC
(S Suffix)
0.1968 (5.00)
0.1890 (4.80)
8
0.430 (10.92)
0.348 (8.84)
5
0.2440 (6.20)
0.2284 (5.80)
8
0.1574 (4.00)
0.1497 (3.80)
1
5
1
4
4
PIN 1
0.0688 (1.75)
0.0532 (1.35)
0.0098 (0.25)
0.0040 (0.10)
SEATING
PLANE
0.0500 0.0192 (0.49)
(1.27) 0.0138 (0.35) 0.0098 (0.25)
BSC
0.0075 (0.19)
0.0196 (0.50)
x 45°
0.0099 (0.25)
8°
0°
0.210
(5.33)
MAX
0.280 (7.11)
0.240 (6.10)
0.325 (8.25)
0.300 (7.62)
0.060 (1.52)
0.015 (0.38)
0.160 (4.06)
0.115 (2.93)
0.0500 (1.27)
0.0160 (0.41)
0.022 (0.558) 0.100 0.070 (1.77)
0.014 (0.356) (2.54) 0.045 (1.15)
BSC
0.195 (4.95)
0.115 (2.93)
0.130
(3.30)
MIN
SEATING
PLANE
0.015 (0.381)
0.008 (0.204)
PRINTED IN U.S.A.
PIN 1
C1652a–2–7/95
8-Lead Epoxy DIP
(P Suffix)
–12–
REV. A