RFHIC RWP15020-10

Wideband Power Amplifier
RWP15020-10
Product Features
Application
• GaN on SiC Broadband High Power Amplifier
• UHF/Military
• 1000 to 2000MHz Operation Bandwidth
• Small Signal Gain 29dB min.
• 20W Typical. P3dB
Package : DP-75
Description
The power amplifier module is designed for Broadcasting, Telecommunication, Medical, Military and Other markets.
Operating frequency range is from 1000MHz to 2000MHz
Gallium Nitride on SiC technology is used and attached on an aluminum sub carrier. Full in/out matching for broadband
performance is already applied.
Improved thermal handling by patented technology.
Typical Specifications
No
Item
1
Bandwidth
2
Small Signal Gain
3
Gain Variation vs Temperature
4
Gain Variation vs Frequency
5
P3dB
6
VCC = +28V; T = 25℃; ZS = ZL = 50Ω
Conditions
Min
Typ
1000
27
-20°C to 60°C
29
-2
±1
1000MHz to 1200MHz
41
43
1200MHz to 2000MHz
42
44
OIP3 @ Po = +33dBm
1000MHz to 1600MHz
48
50
(1MHz Tone spacing, CW 2-Tone)
1600MHz to 2000MHz
46
48
Max
Unit
2000
MHz
31
dB
+2
dB
±2
dBpp
dBm
dBm
7
Input Return Loss
-10
-6
dB
8
Output Return Loss
-10
-5
dB
9
2nd Harmonic suppression
-35
-28
dBc
10
Supply Voltage
28
30
V
11
Quiescent Current consumption
2.2
2.5
A
12
Current Consumption @ P3dB
3.6
A
13
On/Off Switching Time
5
uS
14
CW 1-tone
@Po = +30dBm, Freq 1000MHz
Vcc(=Vds)
27.5
CW 1-tone
On : TTL "Low"
3
Off : TTL "High"(100mA@Disable)
Shut Down or Switch On/Off
On : TTL “Low”(Enable)
TTL Voltage
Off : TTL “High”
0
2.5
0.5
5
5.5
V
▪ Tel : 82-31-250-5011
▪ All specifications may change without notice.
▪ [email protected]
▪ Version 1.0
Wideband Power Amplifier
RWP15020-10
Environmental Characteristics
No
Item
Min
Typ
Max
Unit
1
Operating Temperature
-20
+60
°C
2
Storage Temperature
-40
+105
°C
3
Vibration
MIL-STD-810G Method 514.6 ANNEX C
Absolute Maximum Ratings
No
Item
Rating
Unit
1
Operating Flange Temperature
+85
°C
2
Input RF Power
+20
dBm
3
Supply Voltage
+30
V
4
Load Mismatch Value
3 : 1 @all load phase
* Input Signal Condition : CW 1-Tone
Ordering Information
No
Part Number
Package
1
RWP15020-10
Pallet
2
RWP15020-1H
Module assembled with RWP05020-10
* RWP15020-1H is a SMA connectorized housing version of RWP15020-10. Electrical parameters are all same as RWP15020-10.
For more information, please contact RFHIC
▪ Tel : 82-31-250-5011
▪ All specifications may change without notice.
▪ [email protected]
▪ Version 1.0
Wideband Power Amplifier
RWP15020-10
RWP15020-10 Typical Performance @ 25℃
Frequency
P1dB
P3dB
Current@P1dB
Current@P3dB
2nd Harm
OIP3
(MHz)
(dBm)
(dBm)
(A)
(A)
@30dBm(dBc)
(30dBm/Tone)
1000
39.4
42.5
2.3
2.9
-34.7
49.5
1100
39.8
42.9
2.4
3.1
-43.5
49.8
1200
40.6
43.8
2.1
3.3
-49.4
50.4
1300
41.5
44.5
2.5
3.3
-47.7
50.8
1400
42.1
44.5
2.5
3.3
-43.3
51.0
1500
42.3
45.2
2.5
3.2
-41.8
51.1
1600
43.0
45.4
2.4
3.0
-43.8
51.0
1700
43.2
45.4
2.3
2.7
-46.1
50.3
1800
42.6
44.8
2.1
2.5
-49.6
49.5
1900
42.4
44.3
2.0
2.3
-52.7
48.5
2000
42.0
43.9
2.0
2.3
-61.3
47.6
P3dB
2nd Harmonics
OIP3
Power Gain @ Pin=18dBm
▪ Tel : 82-31-250-5011
▪ All specifications may change without notice.
▪ [email protected]
▪ Version 1.0
Wideband Power Amplifier
RWP15020-10
Precautions
1. This product is designed to be used for broadband amplification.
Heat generation is higher when there is no RF signal in the device. Therefore, the worst case scenario is when there is no
RF signal, and the amplifier is “on” with current draw. The temperature must be calculated properly.
Case temperature must maintain below 85°C.
2. Thermal Grease or Metal Thermal Interface Materials are recommended for heat dissipation.
An example would be spreading thermal grease on the bottom of the device.
Package Dimensions (Type: DP-75)
(Unit : mm/[inch], Tolerance : ±0.2/[.008])
70
[2.756]
70
[2.756]
60
[2.362]
60
[2.362]
20
[.787]
38
[1.496]
50.8
[2]
45
[1.772]
20
[.787]
1.5
[.059]
15.6
[.616]
'A'
7.3
[.286]
6.2
[.245]
6.9
[.273]
C
38
[1.496]
50.8
[2]
7.3
[.288]
6.9
[.273]
1
[.039]
3.8
[.15]
5
[.197]
3
[.12]
2.5
[.096]
17.1
[.673]
2.7
[.106]
4.1
[.161]
1.5
[.059]
How to connect the amplifier to a target PCB
Method-І (with Pin)
Method-ΙІ (without Pin) - If you cut out the pin
▪ Tel : 82-31-250-5011
▪ All specifications may change without notice.
▪ [email protected]
▪ Version 1.0
Wideband Power Amplifier
RWP15020-10
Pin Description
Pin No
Port Name
Function
1
RF IN
RF Input
2
Vcc(+28V)
DC Supply
3
Shut Down(+5V)
Shut Down @ TTL High, Enable @ TTL Low
4
Switch ON/OFF
Disable @ TTL High (Switch Status : Off)
5
GND
Ground
6
RF OUT
RF Output
* Terminal Pin Information : ASK206091,AA (Acethink, Pin) , ASK20556,AA-1(Acethink, Pin Socket)
* Recommended Screw Torque : 8.0kgf.cm±1 using SEMS M3 10mm Bolt
Note :
RFHIC Corporation (RFHIC) reserves the right to make changes to any products herein or to discontinue any product at any time without notice. RFHIC do not
assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including without limitation consequential or
incidental damages. The product specifications herein expressed have been carefully checked and are assumed to be reliable. However, RFHIC disclaims liability for
inaccuracies and strongly recommends buyers to verify that the information they are using is current before placing purchase orders. RFHIC products are not
intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. Buyer uses or sells
such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC and its directors, officers, stockholders,
employees, representatives and distributors harmless against any and all claims arising out of such use. RFHIC’s liability under or arising out of damages, claims of
whatsoever kind and nature which RFHIC products could cause shall be limited in amount to the net purchase price of the products sold to buyer by RFHIC.
▪ Tel : 82-31-250-5011
▪ All specifications may change without notice.
▪ [email protected]
▪ Version 1.0