S−AV38 TOSHIBA RF POWER AMPLIFIER MODULE S−AV38 ○RF POWER AMPLIFIER MODULE for VHF BAND ·for digital use ABSOLUTE MAXIMUM RATINGS (Tc = 25℃) CHARACTERISTIC SYMBOL RATING UNIT DC Supply Voltage VDD 17 V DC Supply Voltage VGG 7 V Pi 17 dBmW Tc (opr) −30~100 ℃ Tstg −40~110 ℃ Input Power Operating Case Temperature Range Storage Temperature Range Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). PACKAGE OUTLINE 26.6±0.1 ⑤ ① +0.2 ② ③④ 6.5 2.2 +0.15/-0.1 φ3±0.1 Unit in mm ±0.65 ±0.65 +0.2 ±0.65 ±0.65 1. RF INPUT 2. VGG 3. VDD 4. RF OUTPUT 5. GROUND (FLANGE) JEDEC JEITA TOSHIBA 5-23F Weight:3.5g 1 2007-11-01 S−AV38 ELECTRICAL CHARACTERISTICS (Tc = 25℃, ZG = 50Ω) CHARACTERISTIC Frequency Range SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT — 260 — 266 MHz 38.8 — — dBmW — — 5 dBmW 2.5 — 3.5 V — — 1 mA — — -35 dB — — -27 dB — — -30 dB — — -35 dB — — 3 — — — 2.5 — — — ±12 ° frange VDD = 7.2V, Po=35dBmW(Pi=adjust) Output Power Po IDD=1.7A(VGG = adjust) , ZL = 50Ω After that Pi = 15dBmW Input Power Pi Gate Bias Voltage VGG Gate Bias Current IGGBias VDD = 7.2V, IDD = 1.7A (VGG = adjust) Po = 35dBmW(Pi=adjust), ZL = 50Ω VDD = 7.2V, IDD = 1.7A (VGG = adjust) Po = 35dBmW(Pi=adjust), ZL = 50Ω VDD = 7.2V, IDD = 1.7A (VGG = adjust) Po = 35dBmW (Pi= adjust), ZL = 50Ω After that Pi OFF VDD = 7.2V, IDD = 1.7A (VGG = adjust) Po = 35dBmW (Pi= adjust), ZL = 50Ω Adjacent-Channel Power Ratio ACP Modulated Wave :π/4·DQPSK (α=0.5, 32kbps) Band Width : 16kHz Frequency Offset : 25kHz Second Harmonic 2nd HRM Third Harmonic 3rd HRM Harmonic Rate of Adjustment for Input Load Rate of Adjustment for Output Load VDD = 7.2V, IDD = 1.7A (VGG = adjust) Po = 35dBmW (Pi= adjust), ZL = 50Ω HRM VSWRin VSWRout Input VSWR ( When RF output pin connects 50Ω Load ) Input VSWR ( When RF input pin connects 50Ω Load ) VDD= 7.2V, IDD = 1.7A (VGG = adjust) Ralative Phase Variation — Po = 5 to 35dBmW (Pi= adjust) ZL = 50Ω(@ Po = 35dBmW) VDD = 7.2V, IDD = 1.7A (VGG = adjust) Load Mismatch — Po = 35dBmW (Pi= adjust, ZL = 50Ω) No Degradation — VSWR LOAD 20: 1 ALL PHASE VDD = 6.0 to 9.0V, VGG = 1 to 5V Stability — Pi = -40 to 13 dBmW VSWR LOAD 3: 1 ALL PHASE All spurious output than 60dB below — desired signal Caution ･ This product has intersetting cap. Please pay attention for exceeding stress and foreign matter in your application. And not to take away the cap. ･ Do not break, cut, crush or dissolve chemically. Dispose of this product properly according to law. Do not intermingle with normal industrial or domestic waste. ･ This product is electrostatic sensitivity, please handle with caution. 2 2007-11-01 S−AV38 SCHEMATIC 4. Po ZL=50Ω 1. Pi ZG=50Ω 2. VGG 3. VDD 5. GROUND (FLANGE) TEST FIXTURE L C1 L C1 C2 C2 C1 : 10000pF C2 : 10μF L : φ0.8 ENAMEL WIRE 8T 5ID 3 2007-11-01 S−AV38 RESTRICTIONS ON PRODUCT USE 20070701-EN GENERAL • The information contained herein is subject to change without notice. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 4 2007-11-01