AD ADM1186

Quad Voltage Up and Down Sequencer
and Monitor with Programmable Timing
ADM1186
FEATURES
GENERAL DESCRIPTION
Powered from 2.7 V to 5.5 V on the VCC pin
Monitors four supplies via 0.8% accurate comparators
Digital core supports up and down supply sequencing
Multiple devices can be cascaded (ADM1186-1)
Four inputs can be programmed to monitor different voltage
levels with resistor dividers
Capacitor programmable supply sequence time delays
and a timeout delay to 5% accuracy at 25°C
Four open-drain enable outputs
Open-drain power-good output
Open-drain sequence complete pin and bidirectional
open-drain fault pin (ADM1186-1 only)
The ADM1186-1 and ADM1186-2 are integrated, four-channel
voltage monitoring and sequencing devices. A 2.7 V to 5.5 V
power supply is required on the VCC pin for power.
Four precision comparators, VIN1 to VIN4, monitor four
voltage rails. All four comparators share a 0.6 V reference and
have a worst-case accuracy of 0.8%. Resistor networks that are
external to the VIN1, VIN2, VIN3, and VIN4 pins set the
undervoltage (UV) trip points for the monitored supply rails.
The ADM1186-1 and ADM1186-2 have four open-drain enable
outputs, OUT1 to OUT4, that are used to enable power supplies.
An open-drain power-good output, PWRGD, indicates whether
the four VINx inputs are above their UV thresholds.
APPLICATIONS
A state machine monitors the state of the UP and DOWN pins
on the ADM1186-1 or the UP/DOWN pin on the ADM1186-2
to control the supply sequencing direction (see Figure 2). In the
WAIT START state, a rising edge transition on the UP or
UP/DOWN pin triggers a power-up sequence. A falling edge
transition on the DOWN or UP/DOWN pin in the POWER-UP
DONE state triggers a power-down sequence.
Monitor and alarm functions
Up and down power supply sequencing
Telecommunication and data communication equipment
PCs, servers, and notebook PCs
APPLICATION DIAGRAM
5V
5V
IN
ADP1706
EN
2.5V
OUT
5V
5V
IN
ADP2107
EN
OUT
3.3V AUX
1.8V
3.3V AUX
IN
ADP1821
3.3V AUX
EN
1µF
1.2V
OUT
5V
5V
IN
ADP1706
EN
100nF
OUT
3.3V
3.3V AUX
VCC
OUT1
OUT2
OUT3
OUT4
FAULT
SEQUENCE CONTROL
VIN1
VIN2
VIN3
VIN4
UP
DOWN
ADM1186-1
DLY_EN_OUT1
2.5V AUX
DLY_EN_OUT3
PWRGD
DLY_EN_OUT4
BLANK_DLY
GND
SEQ_DONE
3.3V AUX
07153-003
DLY_EN_OUT2
Figure 1.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2008 Analog Devices, Inc. All rights reserved.
ADM1186
TABLE OF CONTENTS
Features .............................................................................................. 1
UVLO Behavior.......................................................................... 13
Applications....................................................................................... 1
Power-Up Sequencing and Monitoring................................... 13
General Description ......................................................................... 1
Operation in POWER-UP DONE State.................................. 14
Application Diagram........................................................................ 1
Power-Down Sequencing and Monitoring ............................. 14
Revision History ............................................................................... 2
Input Glitch Filtering ................................................................. 14
Specifications..................................................................................... 4
Fault Conditions and Fault Handling ...................................... 14
Absolute Maximum Ratings............................................................ 6
Defining Time Delays................................................................ 15
ESD Caution.................................................................................. 6
Sequence Control Using a Supply Rail .................................... 16
Pin Configurations and Function Descriptions ........................... 7
Cascading Multiple Devices.......................................................... 23
Typical Performance Characteristics ............................................. 9
Outline Dimensions ....................................................................... 26
Theory of Operation ...................................................................... 13
Ordering Guide .......................................................................... 26
REVISION HISTORY
5/08—Revision 0: Initial Version
Rev. 0 | Page 2 of 28
ADM1186
During a power-up sequence, the state machine enables each
power supply in turn. The supply output voltage is monitored to
determine whether it rises above the UV threshold level within
a user defined duration called the blanking time. If a supply
rises above the UV threshold, the next enable output in the
sequence is turned on. In addition to the blanking time, the
user can also define a sequence time delay before each enable
output is turned on.
The ADM1186-1 provides an open-drain pin, SEQ_DONE,
that is asserted high to provide an indication that a power-up
sequence is complete. The SEQ_DONE pin allows multiple
cascaded ADM1186-1 devices to perform controlled power-up
and power-down sequences.
During a power-down sequence, the enable outputs turn off
in reverse order. The same sequence time delays used during
the power-up sequence are also used during the power-down
sequence as each enable output is turned off; no blanking time
is used during a power-down sequence. At the end of a powerdown sequence, the SEQ_DONE pin is brought low.
POWER-DOWN
DONE
WAIT START
SEQUENCE
SUPPLY 1 OFF
FAULT HANDLER
The ADM1186-1 has a bidirectional pin, FAULT, that facilitates
fault handling when using multiple devices. If an ADM1186-1
experiences a fault condition, the FAULT pin is driven low,
causing other connected ADM1186-1 devices to enter their own
fault handling states.
The ADM1186-1 is available in a 20-lead QSOP package, and
the ADM1186-2 is available in a 16-lead QSOP package.
SEQUENCE UP
TRIGGER
FAULT CONDITION OCCURS
IN ANY STATE
SEQUENCE
SUPPLY 3 OFF
SEQUENCE
SUPPLY 4 OFF
SEQUENCE
SUPPLY 1 ON
SEQUENCE
SUPPLY 2 ON
SEQUENCE
SUPPLY 3 ON
SEQUENCE
SUPPLY 4 ON
SEQUENCE DOWN TRIGGER
Figure 2. Simplified State Machine Diagram
Rev. 0 | Page 3 of 28
POWER-UP DONE
07153-004
SEQUENCE
SUPPLY 2 OFF
During sequencing and when powered up, the state machine
continuously monitors the part for any fault conditions. Faults
include a UV condition on any of the inputs or an unexpected
control input. Any fault causes the state machine to enter a fault
handler, which immediately turns off all enable outputs and
then ensures that the device is ready to start a new power-up
sequence.
ADM1186
SPECIFICATIONS
VVCC = 2.7 V to 5.5 V, TA = −40°C to +85°C; typical values at TA = 25°C, unless otherwise noted.
Table 1.
Parameter
VCC PIN
Operating Voltage Range, VVCC
Undervoltage Lockout, VUVLO
Undervoltage Lockout Hysteresis
Supply Current, IVCC
VIN1 TO VIN4 (VINx) PINS
Input Current
Input Threshold 1
Input Glitch Immunity
Positive Glitch Duration
Negative Glitch Duration
UP, DOWN, AND UP/DOWN PINS
Input Current
1
Input Threshold
Input Glitch Immunity
Min
Typ
Max
Unit
2.7
3.3
2.46
50
146
5.5
210
V
V
mV
μA
−25
−100
0.5952
nA
nA
V
VVINx = 0 V to 1 V
VVINx = 0 V to 5.5 V; VVINx can be greater than VVCC
0.6000
+25
+100
0.6048
19.9
2.75
26.6
4.7
33.2
6.6
μs
μs
50 mV input overdrive
50 mV input overdrive
+100
nA
VUP/DOWN = 0 V to 5.5 V; VUP/DOWN can be greater than VVCC
1.4
6.8
4.9
1.428
9.7
7.9
V
μs
μs
100 mV input overdrive
1 V input overdrive
5
9
%
−100
1.372
3.3
2.7
DLY_EN_OUTx AND BLANK_DLY PINS
Time Delay Accuracy
Time Delay Charge Current
Time Delay Threshold
Time Delay Discharge Resistor
OUT1 TO OUT4 (OUTx) PINS
Output Low Voltage, VOUTL
Leakage Current
VVCC That Guarantees Valid Outputs
PWRGD PIN
Output Low Voltage, VPWRGDL
Leakage Current
VVCC That Guarantees Valid Outputs
FAULT PIN
Input Threshold1
Input Glitch Immunity
Output Low Voltage, VFAULTL
Leakage Current
VVCC That Guarantees Valid Outputs
14
1.4
450
1
Steady state; sequence complete
External capacitor values of 10 nF to 2.2 μF; excludes
external capacitor tolerance
0.4
1
V
μA
V
VVCC = 2.7 V, ISINK = 2 mA
OUTx = 5.5 V
Output is guaranteed to be either low (VOUTL = 0.4 V)
or giving a valid output level from VVCC = 1 V, ISINK =
30 μA or VVCC = 1.1 V, ISINK = 100 μA
0.4
1
V
μA
V
VVCC = 2.7 V, ISINK = 2 mA
PWRGD = 5.5 V
Output is guaranteed to be either low (VPWRGDL = 0.4 V)
or giving a valid output level from VVCC = 1 V, ISINK =
30 μA or VVCC = 1.1 V, ISINK = 100 μA
1.428
8.1
0.4
V
μs
V
1
μA
V
1
1.4
5.6
VVCC falling
μA
V
Ω
1
1.372
3.1
Test Conditions/Comments
Rev. 0 | Page 4 of 28
1 V input overdrive
VVCC = 2.7 V, ISINK = 2 mA
FAULT = 5.5 V
Output is guaranteed to be either low (VFAULTL = 0.4 V)
or giving a valid output level from VVCC = 1 V, ISINK =
30 μA or VVCC = 1.1 V, ISINK = 100 μA
ADM1186
Parameter
SEQ_DONE PIN
Output Low Voltage, VSEQ_DONEL
Leakage Current
VVCC That Guarantees Valid Outputs
Min
Typ
Max
Unit
Test Conditions/Comments
0.4
1
V
μA
V
VVCC = 2.7 V, ISINK = 2 mA
SEQ_DONE = 5.5 V
Output is guaranteed to be either low (VSEQ_DONEL = 0.4 V)
or giving a valid output level from VVCC = 1 V, ISINK = 30 μA
or VVCC = 1.1 V, ISINK = 100 μA
Includes input glitch filter and all other internal
delays
1
RESPONSE TIMING
VINx to PWRGD
VINx Going Low to High
VINx Going High to Low
VINx to FAULT, OUTx Low
VINx Going High to Low (UV Fault)
UP, DOWN, and UP/DOWN to FAULT,
OUTx Low, tUDOUT
External FAULT to OUTx Low
Fault Hold Time
1
21.9
5.8
28.8
7.3
35.2
8.9
μs
μs
50 mV input overdrive
50 mV input overdrive
6.1
5.5
7.5
8.6
9.2
12.1
μs
μs
50 mV input overdrive
100 mV input overdrive
5.8
7.7
35
44
10.5
10
54
μs
μs
μs
1 V input overdrive
1 V input overdrive
UP, UP/DOWN held low
Input comparators do not include hysteresis on their inputs. The comparator output passes through a digital glitch filter to remove short transients from the input
signal that would otherwise drive the state machine.
Rev. 0 | Page 5 of 28
ADM1186
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 2.
Parameter
VCC Pin
VINx Pins
UP, DOWN, UP/DOWN Pins
DLY_EN_OUTx, BLANK_DLY Pins
PWRGD, SEQ_DONE, OUTx Pins
FAULT Pin
Operating Temperature Range
Storage Temperature Range
Lead Temperature Convection Reflow
Peak Temperature
Time at Peak Temperature
Junction Temperature
Table 3. Thermal Resistance
Rating
−0.3 V to +6 V
−0.3 V to +6 V
−0.3 V to +6 V
−0.3 V to VCC + 0.3 V
−0.3 V to +6 V
−0.3 V to +6 V
−40°C to +85°C
−65°C to +150°C
Package Type
16-Lead QSOP
20-Lead QSOP
ESD CAUTION
260°C
≤30 sec
125°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. 0 | Page 6 of 28
θJA
149.97
125.80
Unit
°C/W
°C/W
ADM1186
1
20
VCC
2
19
OUT1
GND
1
16
VCC
VIN2
3
18
OUT2
VIN1 2
15
OUT1
VIN3
4
17
OUT3
VIN2 3
ADM1186-2
14
OUT2
VIN4
5
16
OUT4
VIN3 4
TOP VIEW
(Not to Scale)
13
OUT3
UP
6
15
PWRGD
VIN4 5
12
OUT4
DOWN
7
14
SEQ_DONE
UP/DOWN 6
11
PWRGD
FAULT
8
13
BLANK_DLY
DLY_EN_OUT2
7
10
BLANK_DLY
DLY_EN_OUT1
9
12
DLY_EN_OUT4
DLY_EN_OUT3
8
9
DLY_EN_OUT2 10
11
DLY_EN_OUT3
ADM1186-1
TOP VIEW
(Not to Scale)
07153-005
GND
VIN1
Figure 3. ADM1186-1 Pin Configuration
DLY_EN_OUT4
07153-006
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
Figure 4. ADM1186-2 Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
ADM1186-1 ADM1186-2
1
1
2
2
Mnemonic
GND
VIN1
3
3
VIN2
4
4
VIN3
5
5
VIN4
6
UP
7
DOWN
6
UP/DOWN
8
FAULT
9
DLY_EN_OUT1
10
7
DLY_EN_OUT2
11
8
DLY_EN_OUT3
Description
Chip Ground Pin.
Noninverting Comparator Input. The voltage on this pin is compared with a 0.6 V
reference. Can be used to monitor a voltage rail via a resistor divider. The output of this
comparator is monitored by the state machine.
Noninverting Comparator Input. The voltage on this pin is compared with a 0.6 V
reference. Can be used to monitor a voltage rail via a resistor divider. The output of this
comparator is monitored by the state machine.
Noninverting Comparator Input. The voltage on this pin is compared with a 0.6 V
reference. Can be used to monitor a voltage rail via a resistor divider. The output of this
comparator is monitored by the state machine.
Noninverting Comparator Input. The voltage on this pin is compared with a 0.6 V
reference. Can be used to monitor a voltage rail via a resistor divider. The output of this
comparator is monitored by the state machine.
Noninverting Comparator Input. A rising edge on this pin initiates a power-up sequence
when the ADM1186-1 is in the WAIT START state.
Noninverting Comparator Input. A falling edge on this pin initiates a power-down
sequence when the ADM1186-1 is in the POWER-UP DONE state.
Noninverting Comparator Input. A rising edge on this pin initiates a power-up sequence
when the ADM1186-2 is in the WAIT START state. A falling edge on this pin initiates a
power-down sequence when the ADM1186-2 is in the POWER-UP DONE state.
Active Low, Bidirectional, Open-Drain Pin. When an internal fault is detected by the
ADM1186-1 state machine, this pin is asserted low and the SET FAULT state is entered.
An external device pulling this pin low also causes the ADM1186-1 to enter the SET
FAULT state.
Timing Input. The capacitor connected to this input sets the time delay between the UP
input initiating a power-up sequence and OUT1 being asserted high. During a powerdown sequence, this input sets the time delay between OUT1 being asserted low and
SEQ_DONE being asserted low.
Timing Input. The capacitor connected to this input sets the time delay between VIN1
coming into compliance and OUT2 being asserted high during a power-up sequence.
During a power-down sequence, this input sets the time delay between OUT2 being
asserted low and OUT1 being asserted low.
Timing Input. The capacitor connected to this input sets the time delay between VIN2
coming into compliance and OUT3 being asserted high during a power-up sequence.
During a power-down sequence, this input sets the time delay between OUT3 being
asserted low and OUT2 being asserted low.
Rev. 0 | Page 7 of 28
ADM1186
Pin No.
ADM1186-1 ADM1186-2
12
9
Mnemonic
DLY_EN_OUT4
13
BLANK_DLY
10
14
SEQ_DONE
15
11
PWRGD
16
12
OUT4
17
13
OUT3
18
14
OUT2
19
15
OUT1
20
16
VCC
Description
Timing Input. The capacitor connected to this input sets the time delay between VIN3
coming into compliance and OUT4 being asserted high during a power-up sequence.
During a power-down sequence, this input sets the time delay between OUT4 being
asserted low and OUT3 being asserted low.
Timing Input. The capacitor connected to this input sets the blanking time. This is the
time allowed between OUTx being asserted and VINx coming into compliance; otherwise,
the SET FAULT state is entered.
Active High, Open-Drain Output. This output is pulled low when VCC = 1 V. When the
power-up sequence is complete, SEQ_DONE is asserted high. During a power-down
sequence, the pin remains asserted until the time delay set by DLY_EN_OUT1 has
elapsed. When a fault occurs, this pin is asserted low.
Active High, Open-Drain Output. This output is pulled low when VCC = 1 V. The output
state of this pin is a logical AND function of the UV threshold state of the VINx pins. When
the voltage on all VINx inputs exceeds 0.6 V, PWRGD is asserted. This output is driven low
if the voltage on any VINx pin is below 0.6 V.
Active High, Open-Drain Output. This output is pulled low when VCC = 1 V. During a
power-up sequence, this output is asserted high after the time delay set by the capacitor
on DLY_EN_OUT4 has elapsed. The output is asserted low immediately after a powerdown sequence has been initiated.
Active High, Open-Drain Output. This output is pulled low when VCC = 1 V. During a
power-up sequence, this output is asserted high after the time delay set by the capacitor
on DLY_EN_OUT3 has elapsed. During a power-down sequence, the output is asserted
low after the time delay set by the capacitor on DLY_EN_OUT4 has elapsed.
Active High, Open-Drain Output. This output is pulled low when VCC = 1 V. During a
power-up sequence, this output is asserted high after the time delay set by the capacitor
on DLY_EN_OUT2 has elapsed. During a power-down sequence, the output is asserted
low after the time delay set by the capacitor on DLY_EN_OUT3 has elapsed.
Active High, Open-Drain Output. This output is pulled low when VCC = 1 V. During a
power-up sequence, this output is asserted high after the time delay set by the capacitor
on DLY_EN_OUT1 has elapsed (ADM1186-1) or immediately after a rising edge on
UP/DOWN (ADM1186-2). During a power-down sequence, the output is asserted low
after the time delay set by the capacitor on DLY_EN_OUT2 has elapsed.
Positive Supply Input Pin. The operating supply voltage range is 2.7 V to 5.5 V.
Rev. 0 | Page 8 of 28
ADM1186
160
38
140
36
POSITIVE GLITCH DURATION (µs)
120
100
80
60
40
20
0
0.5
1.0
1.5
2.0 2.5 3.0 3.5 4.0
SUPPLY VOLTAGE (V)
4.5
5.0
5.5
30
VCC = 3.3V
28
26
24
20
Figure 5. Supply Current vs. Supply Voltage
0
50
100
OVERDRIVE (mV)
150
200
Figure 8. VINx Input Positive Glitch Immunity vs. Input Overdrive
150
18
16
NEGATIVE GLITCH DURATION (µs)
VCC = 5.5V
145
SUPPLY CURRENT (µA)
32
22
07153-007
0
34
07153-010
SUPPLY CURRENT (µA)
TYPICAL PERFORMANCE CHARACTERISTICS
140
VCC = 3.3V
135
VCC = 2.7V
130
125
14
12
10
8
6
VCC = 3.3V
4
–20
0
20
40
TEMPERATURE (°C)
60
80
0
07153-008
31.0
604
30.5
POSITIVE GLITCH DURATION (µs)
605
603
602
VCC = 3.3V
601
600
599
598
597
100
OVERDRIVE (mV)
150
200
30.0
29.5
VCC = 3.3V
29.0
28.5
28.0
27.5
27.0
26.5
596
595
–40
50
Figure 9. VINx Input Negative Glitch Immunity vs. Input Overdrive
–20
0
20
40
TEMPERATURE (°C)
60
80
26.0
–40
07153-009
VINX INPUT THRESHOLD (mV)
Figure 6. Supply Current vs. Temperature
0
Figure 7. VINx Input Threshold vs. Temperature
–20
0
20
40
TEMPERATURE (°C)
60
80
Figure 10. VINx Input Positive Glitch Immunity vs. Temperature
Rev. 0 | Page 9 of 28
07153-012
120
–40
07153-011
2
6.0
10.0
5.8
9.5
5.6
9.0
INPUT GLITCH DURATION (µs)
5.4
5.2
5.0
VCC = 3.3V
4.8
4.6
4.4
8.5
8.0
7.5
7.0
VCC = 3.3V
6.5
6.0
5.5
4.2
–20
0
20
40
TEMPERATURE (°C)
60
80
5.0
–40
07153-013
4.0
–40
Figure 11. VINx Input Negative Glitch Immunity vs. Temperature
–20
0
20
40
TEMPERATURE (°C)
60
07153-016
NEGATIVE GLITCH DURATION (µs)
ADM1186
80
Figure 14. UP, DOWN, and UP/DOWN Input Glitch Immunity vs. Temperature
1.43
10.0
9.5
INPUT GLITCH DURATION (µs)
THRESHOLD (V)
1.42
1.41
VCC = 3.3V
1.40
1.39
1.38
9.0
8.5
8.0
7.5
7.0
6.5
VCC = 3.3V
6.0
–20
0
20
40
TEMPERATURE (°C)
60
5.0
07153-014
1.37
–40
80
Figure 12. UP, DOWN, UP/DOWN, FAULT, and Time Delay Trip Threshold
vs. Temperature
0
200
400
600
OVERDRIVE (mV)
800
1000
Figure 15. FAULT Input Glitch Immunity vs. Input Overdrive
7.0
10.0
INPUT GLITCH DURATION (µs)
9.0
8.5
8.0
7.5
7.0
VCC = 3.3V
6.5
6.0
6.5
6.0
VCC = 3.3V
5.5
5.0
0
50
100
OVERDRIVE (mV)
150
200
Figure 13. UP, DOWN, and UP/DOWN Input Glitch Immunity
vs. Input Overdrive
5.0
–40
–20
0
20
40
TEMPERATURE (°C)
60
80
Figure 16. FAULT Input Glitch Immunity vs. Temperature
Rev. 0 | Page 10 of 28
07153-018
5.5
07153-015
INPUT GLITCH DURATION (µs)
9.5
07153-017
5.5
ADM1186
400
15.0
14.8
350
14.2
14.0
13.8
VCC = 2.7V
13.6
13.4
300
250
200
150
100
50
13.2
–20
0
20
TEMPERATURE (°C)
40
60
100µA
0
1.0
1.5
07153-019
13.0
–40
1mA
2.0
2.5
3.0
3.5
4.0
SUPPLY VOLTAGE (V)
4.5
5.0
5.5
07153-022
VCC = 5.5V
VCC = 3.3V
14.4
OUTPUT LOW VOLTAGE (mV)
CHARGE CURRENT (µA)
14.6
Figure 20. Output Low Voltage vs. Supply Voltage
Figure 17. Time Delay Charge Current vs. Temperature
9.0
1k
8.5
RESPONSE TIME (µs)
TIME DELAY (ms)
8.0
100
10
7.5
7.0
6.5
6.0
100
1k
10k
CAPACITOR (nF)
5.0
2.7
07153-020
1
10
Figure 18. Time Delay vs. Capacitor Value
5.2
9.0
8.5
500
8.0
RESPONSE TIME (µs)
VCC = 2.7V
400
300
VCC = 3.3V
200
7.5
7.0
6.5
6.0
VCC = 5.5V
100
0
5
10
15
OUTPUT SINK CURRENT (mA)
20
Figure 19. Output Low Voltage vs. Output Sink Current
25
5.0
–40
–20
0
20
40
TEMPERATURE (°C)
60
80
07153-024
5.5
07153-021
OUTPUT LOW VOLTAGE (mV)
3.7
4.2
4.7
SUPPLY VOLTAGE (V)
Figure 21. VINx to FAULT, OUTx Low Response Time vs. Supply Voltage
600
0
3.2
07153-023
5.5
Figure 22. VINx to FAULT, OUTx Low Response Time vs. Temperature
Rev. 0 | Page 11 of 28
ADM1186
10.0
30
9.5
9.0
RESPONSE TIME (µs)
RESPONSE TIME (µs)
25
20
15
8.0
7.5
7.0
VCC = 3.3V
10
8.5
0
50
100
OVERDRIVE (mV)
150
200
6.0
2.5
07153-025
5
Figure 23. VINx to FAULT, OUTx Low Response Time vs. Input Overdrive
3.0
3.5
4.0
4.5
SUPPLY VOLTAGE (V)
5.0
5.5
07153-026
6.5
Figure 24. UP, DOWN, UP/DOWN to FAULT, OUTx Low Response Time
vs. Supply Voltage
Rev. 0 | Page 12 of 28
ADM1186
THEORY OF OPERATION
The operation of the ADM1186 is described in the following
sections. Where necessary, differences between the ADM1186-1
and the ADM1186-2 are noted. Figure 28 is a detailed functional
block diagram of the ADM1186-1, and Figure 30 is a detailed
functional block diagram of the ADM1186-2.
The operation of the ADM1186 is described in the context of a
typical voltage monitoring and sequencing application, as shown
in Figure 1. This example uses the ADM1186-1, because it is
essentially a superset of the functionality of the ADM1186-2. In
the example application, the ADM1186-1 turns on four regulators,
monitors four separate voltage rails, and generates a power-good
signal to turn on a microcontroller when all power supplies are
on and above their UV threshold level. Figure 34 shows a typical
ADM1186-2 voltage sequencing and monitoring application.
UVLO BEHAVIOR
The ADM1186 is designed to ensure that the outputs are always
in a known state for a VCC supply voltage of 1 V or greater; if the
VCC supply voltage is below 1 V, the state of the outputs is not
guaranteed. Figure 25 shows the behavior of the outputs over
the full VCC supply range.
VCC
5.5V
2.7V
VUVLO
In the example shown in Figure 1, the main supply of 3.3 V
powers up the device via the VCC pin. The state machine remains
in the WAIT START state until either a rising edge on the UP
pin initiates a power-up sequence, or a fault condition occurs.
The ADM1186-2 requires a rising edge on the UP/DOWN pin
to start a power-up sequence.
If a rising edge on the UP pin is detected, the state machine
moves to the DELAY 1 state. The ADM1186-2 does not have a
DLY_EN_OUT1 pin, so it omits the DELAY 1 state. Figure 29
shows the ADM1186-1 state machine in detail; Figure 31 shows
the ADM1186-2 state machine. The waveforms for a typical
power-up and power-down sequence when no faults occur are
shown in Figure 32 (ADM1186-1) and Figure 33 (ADM1186-2).
During the ENABLE OUT1 state, the VIN1 pin monitors the
2.5 V supply after a blanking delay, set by the capacitor on the
BLANK_DLY pin. The blanking delay, which is the same for all
supplies, is set to allow the slowest rising supply sufficient time
to switch on.
UVLO
ACTIVE
07153-027
1V
Figure 25. ADM1186 Output Behavior over VCC Supply
As the VCC supply begins to rise, an undervoltage lockout (UVLO)
circuit becomes active and begins to pull the outputs of the
ADM1186 low. The outputs are not guaranteed to be low until
the VCC supply has reached 1 V. State machine operation is also
disabled, so it is not possible to initiate a power-up sequence.
This behavior ensures that enable pins on dc-to-dc converters
or point-of-load (POL) devices connected to the OUTx pins are
held low as the supplies are rising. This prevents the dc-to-dc
converters or the POLs from switching on briefly and then
switching off as the supply rails stabilize.
An external resistor divider scales the supply voltage down for
monitoring at the VIN1 pin (see Figure 26). The resistor ratio is
selected so that the VIN1 voltage is 0.6 V when the supply voltage
rises to the UV level at start-up (a voltage below the nominal 2.5 V
level). In Figure 26, R1 is 7.4 kΩ and R2 is 2.5 kΩ, so a voltage
level of 2.375 V corresponds to 0.6 V on the noninverting input
of the first comparator.
V
2.5V
2.375V
When VCC rises above VUVLO and the internal reference is stable,
the UVLO circuit enables the state machine. The state machine
takes control of the outputs and begins operation from the SET
FAULT state.
Rev. 0 | Page 13 of 28
t
0V
2.375V SUPPLY
GIVES 0.6V
AT VIN1 PIN
R1
7.4kΩ
ADM1186
VIN1
R2
2.5kΩ
0.6V
TO LOGIC
CORE
Figure 26. Setting the Undervoltage Threshold
with an External Resistor Divider
07153-028
ALL OUTPUTS
LOW
0V
POWER-UP SEQUENCING AND MONITORING
In the DELAY 1 state, a time delay, set by the capacitor
connected to the DLY_EN_OUT1 pin, is allowed to elapse.
Then, in the ENABLE OUT1 state, the OUT1 pin is asserted
high. OUT1 is an open-drain, active high output, and in this
application it enables the output of a 2.5 V regulator.
UNDER STATE
MACHINE CONTROL
OUTPUTS
NOT GUARANTEED
After the fault hold time elapses, the state machine moves to the
CLEAR FAULT state. If the UP (ADM1186-1) or UP/DOWN
(ADM1186-2) pin is low, the state machine can exit the CLEAR
FAULT state. This change is indicated on the ADM1186-1 by
the FAULT pin being asserted high. For the ADM1186-2, there
is no external indication that the part is ready to perform
sequencing, so 0.5 ms should be allowed after VCC comes up
before attempting to start a power-up sequence.
ADM1186
If the output of the 2.5 V regulator meets the UV level when the
blanking time elapses, the state machine continues the power-up
sequence, moving into the DELAY 2 state. A time delay, set by
the capacitor connected to the DLY_EN_OUT2 pin, elapses
before turning on the next enable output, OUT2, in the
ENABLE OUT2 state.
If the 1.8 V supply does not rise to the UV level before the
blanking time elapses, sequencing immediately stops and the
state machine enters the SET FAULT state.
The same scheme is implemented with the other output and
input pins. Every supply turned on via an output pin, OUTx, is
monitored via an input pin, VINx, to check that the supply has
risen above the UV level within the blanking time before the
state machine moves on to the next supply.
When a supply is on and operating correctly, the ADM1186
continues to monitor it for the duration of the power-up
sequence. If any supply drops below its UV threshold level
during a power-up sequence, sequencing stops and the state
machine enters the SET FAULT state.
The PWRGD pin is asserted high, independently of the state
machine, when all four VINx pins are above their UV threshold.
The state machine in the ADM1186-1 indicates that the powerup sequence is complete by asserting the SEQ_DONE pin high.
OPERATION IN POWER-UP DONE STATE
When the power-up sequence is complete, the state machine
remains in the POWER-UP DONE state until one of the
following events occurs:
•
•
•
During a power-down sequence, the state machine monitors the
supplies that are still on. If a supply drops below its UV threshold
before it is turned off, the power-down sequence immediately
stops and the state machine enters the SET FAULT state.
A rising edge on the UP or UP/DOWN pin during a powerdown sequence generates a fault.
The PWRGD pin is asserted low, independently of the state
machine power-down sequence, when one or more of the
VINx pins drops below 0.6 V.
INPUT GLITCH FILTERING
When the state machine is in the WAIT START state, or at any
time during a power-up sequence, a falling edge on the DOWN
pin (ADM1186-1) or the UP/DOWN pin (ADM1186-2) generates
a fault.
•
This sequence of steps is repeated until all four regulators
are switched off and the device is in the WAIT START state.
Because the ADM1186-2 does not have a DLY_EN_OUT1 pin,
there is no delay between the OUT1 pin being brought low and
the state machine returning to the WAIT START state. When
the device is in the WAIT START state, the SEQ_DONE pin is
brought low.
A falling edge occurs on the DOWN (ADM1186-1) or
UP/DOWN (ADM1186-2) pin, initiating a power-down
sequence.
An undervoltage condition occurs on one or more of VIN1
to VIN4, generating a fault.
A rising edge occurs on the UP pin, generating a fault
(ADM1186-1 only).
An external device brings the FAULT pin low, causing a
fault (ADM1186-1 only).
The VINx, UP, DOWN, and FAULT inputs on the ADM1186-1
and the VINx and UP/DOWN inputs on the ADM1186-2 use a
time-based glitch filter to prevent false triggering. The glitch
filter avoids the need to use some of the operating supply range
to provide hysteresis on an input. This helps to maximize the
available operating supply range for a system, which is especially
important in systems where low supply voltages are being used.
The VINx inputs use a positive glitch filter that is approximately
five times longer than the negative glitch filter. This provides
additional glitch immunity during the power-up sequence as a
supply is rising, but still allows for a quick response in the event
of an undervoltage event on an input.
FAULT CONDITIONS AND FAULT HANDLING
During supply sequencing and operation in the POWER-UP
DONE state, the ADM1186 continuously monitors the VINx,
UP, DOWN, and UP/DOWN pins for fault conditions. The
FAULT pin on the ADM1186-1 is monitored to detect external
faults generated by other devices, which is important during
cascade operation.
The following faults are internally generated:
•
POWER-DOWN SEQUENCING AND MONITORING
•
When the ADM1186 is in the POWER-UP DONE state, a
falling edge on the DOWN or UP/DOWN pin initiates a
power-down sequence (see Figure 29 or Figure 31).
•
The state machine moves to the DISABLE OUT4 state, bringing
the OUT4 pin low and switching off the 3.3 V regulator. A time
delay, set by the capacitor on the DLY_EN_OUT4 pin, elapses
before the state machine moves to the DISABLE OUT3 state.
•
•
Rev. 0 | Page 14 of 28
A supply fails to reach the UV threshold within the time
defined by the BLANK_DLY capacitor during a power-up
sequence.
A UV condition occurs on VINx after the blanking time
has elapsed during a power-up sequence.
A UV condition occurs on VINx before the supply is
disabled during a power-down sequence.
A falling edge occurs on the DOWN or UP/DOWN pin
during a power-up sequence or in the WAIT START state.
A rising edge occurs on the UP or UP/DOWN pin during a
power-down sequence or in the POWER-UP DONE state.
ADM1186
The action taken by the ADM1186 state machine is the same
for an internal or external fault. The state machine enters the
SET FAULT state, asserts the SEQ_DONE and FAULT pins low
(ADM1186-1 only), and asserts all four OUTx enable pins low.
The blanking time is controlled by the capacitor on the
BLANK_DLY pin. This capacitor sets the time allowed between
an enable output being asserted, turning on a supply, and the
output of the supply rising above its defined UV threshold.
The ADM1186 remains in the SET FAULT state for the fault
hold time before moving into the CLEAR FAULT state. If the
UP or UP/DOWN pin is low for a time of t ≥ tUDOUT before the
state machine enters the CLEAR FAULT state, the state machine
can move immediately into the WAIT ALL OK state.
A constant current source is connected to a capacitor through a
switch that is under the control of the state machine. This current
source charges a capacitor until the threshold voltage is reached.
For all capacitors, the duration of the time delay is defined by
the following formula:
The length of time from entering the SET FAULT state to
reaching the WAIT ALL OK state, with the UP or UP/DOWN
pin held low, is the fault hold time. The fault hold time is the
minimum amount of time that the FAULT pin is held low. If the
UP or UP/DOWN pin is high when the state machine enters
the CLEAR FAULT state, the time that the FAULT pin is held
low is extended.
When the ADM1186-1 is in the CLEAR FAULT state and the
UP pin is low, the WAIT ALL OK state is entered and the
FAULT pin is deasserted. If an external device is driving the
FAULT pin low, the state machine remains in the WAIT ALL
OK state until the FAULT pin returns high. The state machine
then transitions into the WAIT START state, ready for the next
power-up sequence.
DEFINING TIME DELAYS
The ADM1186 allows the user to define sequence and blanking
time delays using capacitors. The ADM1186-1 has four
DLY_EN_OUTx pins, and the ADM1186-2 has three
DLY_EN_OUTx pins. Capacitors connected to these pins
control the time delay between supplies turning on or off
during the power-up and power-down sequences. Both devices
provide one pin (BLANK_DLY) to set the blanking time delay.
The ADM1186-1 has a pin called DLY_EN_OUT1 that the
ADM1186-2 does not have. The capacitor on this pin sets the
time delay used before enabling OUT1 during a power-up
sequence, as well as the time delay between disabling OUT1 and
returning to the WAIT START state during a power-down
sequence. Although this time delay is not essential when a
single ADM1186-1 device is used, the time delay is essential
when multiple devices are cascaded (see the Cascading Multiple
Devices section).
When ADM1186-1 devices are used in cascade, the capacitor
on the DLY_EN_OUT1 pin of Device N + 1 sets the sequence
time delay between the last supply of Device N and the first
supply of Device N + 1 being turned on and off.
During the power-up sequence, the capacitors connected to the
DLY_EN_OUTx pins set the time from the end of the blanking
period to the next enable output being asserted high. During
the power-down sequence, the capacitors set the time between
consecutive enable outputs being asserted low.
tDELAY = CDELAY × 0.1
where:
tDELAY is the time delay in seconds.
CDELAY is the capacitor value in microfarads (μF).
For capacitor values from 10 nF to 2.2 μF, the time delay is in
the range of 1 ms to 220 ms. If a capacitor is not connected to
a timing pin, the time delay is minimal, in the order of several
microseconds.
When a capacitor is not being charged by the current source,
it is connected via a resistor to ground. Each capacitor has a
dedicated resistor with a typical value of 450 Ω. To ensure
accurate time delays, time must be allowed for a capacitor to
discharge after it has been used. Typically, allowing five RC time
constants is sufficient for the capacitor to discharge to less than
1% of the threshold voltage.
If the capacitors are not sufficiently discharged after use, the
time delays will be smaller than expected. This can happen if
very small capacitor values are used or if a power-up or powerdown sequence is performed immediately after another
sequence has been completed. Examples of when this behavior
can occur include, but are not limited to, the following:
•
•
•
A power-down sequence is initiated immediately after
entering the POWER-UP DONE state.
A fault occurs in the ENABLE OUT1 state when the
DLY_EN_OUT1 capacitor is charged and a power-up
sequence is started very quickly after the fault has been
handled.
The DLY_EN_OUTx time delay is very short and is insufficient to allow the BLANK_DLY capacitor to fully discharge.
To achieve the best timing accuracy over the operational
temperature range, the choice of capacitor is critical. Capacitors
are typically specified with a value tolerance of ±5%, ±10%, or
±20%, but in addition to the value tolerance, there is also a
variation in capacitance over temperature.
Where high accuracy timing is important, the use of capacitors
that use a C0G, sometimes called NPO, dielectric results in a
capacitance variation of only ±0.3% over the full temperature
range. This capacitance variation contrasts with typical variations of ±15% for X5R and X7R dielectrics and ±22% for X7S
capacitor dielectrics.
Rev. 0 | Page 15 of 28
ADM1186
R2 ⎞
VSHYS = (VH − VL ) × ⎛⎜
⎟
⎝ R1 + R2 ⎠
SEQUENCE CONTROL USING A SUPPLY RAIL
The UP and DOWN inputs on the ADM1186-1 and the
UP/DOWN input on the ADM1186-2 are used to initiate
power-up and power-down sequences. These inputs are
designed for use with digital or analog signals, such as power
supply rails. Using a power supply rail to control the up and
down sequencing allows the ADM1186 to perform sequencing
and monitoring functions for five supply rails.
In the example application shown in Figure 27, the following
values could be used:
RP = 10 kΩ
VP = 5 V
VIN = 3.3 V
When using a supply rail to control an ADM1186-1 (with
the UP and DOWN pins connected) or an ADM1186-2,
some hysteresis is required. The hysteresis is added on the
joined UP and DOWN pins of the ADM1186-1 or on the
UP/DOWN pin of the ADM1186-2 to ensure that a slowly
ramping supply rail does not cause spurious rising or falling
edges that would otherwise cause state machine faults.
The values of the R1 and R2 resistors determine the midpoint
of the hysteresis, VMID, about which VH and VL set the levels at
which power-up and power-down sequences are initiated. For a
3.3 V supply, a threshold just below 3 V could be used, making
R1 = 11 kΩ and R2 = 10 kΩ and giving a midpoint of 2.94 V.
V MID =
To provide the necessary hysteresis, a single additional resistor
(RH in Figure 27) is connected between the joined UP and
DOWN pins of the ADM1186-1 and the OUT1 pin of the
device, or between the UP/DOWN pin of the ADM1186-2 and
the OUT1 pin of the device.
VMID = 2.94 V
As a general rule, the value for RH is approximately 60 times
the value of R1 in parallel with R2. In this example, R1 in
parallel with R2 is 5.24 kΩ, so RH would be approximately
314 kΩ. Taking a value of 300 kΩ for RH and using this value
in the previous equations for VH, VL, and VSHYS, the following
values are obtained:
RH
VIN
ADM1186-1
UP
VCC
⎡ ⎛
10 k + 300 k ⎞⎤
VH = 1.4 × ⎢1 + ⎜11 k ×
⎟
10 k × 300 k ⎠⎥⎦
⎣ ⎝
RP
OUT1
+
VH = 2.991 V
–
R2
DOWN
1.4V
+
⎡
⎛ 1.4
5 − 1. 4 ⎞ ⎤
⎟⎥
VL = 1.4 + ⎢11 k × ⎜
−
⎜ 10 k 300 k + 10 k ⎟⎥
⎝
⎠⎦
⎣⎢
STATE
MACHINE
–
07153-038
R1
VP
3.3V
VL = 2.812 V
Figure 27. Using a Supply Rail to Control Sequencing with Hysteresis
When OUT1 is low, the resistor RH sinks current from the
node at the midpoint of R1 and R2, slightly increasing the VIN
voltage needed to start a power-up sequence, referred to as VH.
When OUT1 is high, RH sources current into the midpoint of
R1 and R2, decreasing the VIN voltage necessary to start a
power-down sequence, referred to as VL.
The hysteresis at the VIN node is simply VH − VL. As the R1
and R2 resistors scale VIN down, the hysteresis on VIN is also
scaled down. The scaled hysteresis, VSHYS, at the inputs to the
UP and DOWN pins (ADM1186-1) or the UP/DOWN pin
(ADM1186-2) must be at least 75 mV. The value of RH is
selected to ensure that this is the case.
R2 + RH ⎞⎤
⎡
VH = 1.4 × ⎢1 + ⎛⎜ R1 ×
⎟
R2 × RH ⎠⎥⎦
⎝
⎣
VIN × R2 3.3 × 10 k
=
R1 + R2 11 k+ 10 k
⎛ 10 k ⎞
VSHYS = (2.991 − 2.812 ) × ⎜
⎟
⎝ 11 k + 10 k ⎠
VSHYS = 0.085 V
Because the value of VSHYS is greater than the 75 mV of scaled
hysteresis required, the RH resistor value selected is sufficient.
If the value of VSHYS obtained is too small, the value of RH can
be reduced, increasing the scaled hysteresis provided.
It should be noted that it is not possible to directly connect the
VCC supply to the UP pin (ADM1186-1) or to the UP/DOWN
pin (ADM1186-2) to start a sequence as the VCC comes up.
When the UVLO circuit enables the state machine, it begins
in the fault handler states. To reach the WAIT START state so
that sequencing can begin, the UP pin (ADM1186-1) or the
UP/DOWN pin (ADM1186-2) must be held low after the state
machine is enabled.
⎡
⎛ 1.4
VP − 1.4 ⎞⎟⎤
VL = 1.4 + ⎢R1 × ⎜
−
⎥
⎜ R2
RH + RP ⎟⎠⎥⎦
⎢⎣
⎝
Rev. 0 | Page 16 of 28
ADM1186
VCC
ADM1186-1
VIN1
GLITCH FILTER
PWRGD
VIN2
GLITCH FILTER
VIN3
GLITCH FILTER
OUT1
VIN4
GLITCH FILTER
OUT2
0.6V
UP
GLITCH FILTER
RISING EDGE
DETECT
STATE
MACHINE
DOWN
GLITCH FILTER
OUT3
FALLING EDGE
DETECT
OUT4
FAULT
GLITCH FILTER
1.4V
SEQ_DONE
14µA
DLY_EN_OUT1
DLY_EN_OUT2
DLY_EN_OUT3
DLY_EN_OUT4
BLANK_DLY
CAPACITOR MUX
AND DISCHARGE
450Ω
GND
Figure 28. Functional Block Diagram of the ADM1186-1
Rev. 0 | Page 17 of 28
07153-029
1.4V
ADM1186
FAULT IN: HIGH
WAIT ALL OK
FAULT OUT: HIGH
UP: LOW
WAIT START
FAULT IN: LOW
OUT1: LOW OUT4: LOW
OUT2: LOW SEQ_DONE: LOW DOWN: FALLING EDGE
OUT3: LOW FAULT OUT: HIGH
CLEAR FAULT
F
FAULT HOLD
TIMES OUT
UP: RISING EDGE
SET FAULT
DELAY 1
FAULT IN: LOW
DOWN: FALLING EDGE
F
OUT1: LOW OUT4: LOW
OUT2: LOW SEQ_DONE: LOW
OUT3: LOW FAULT OUT: LOW
AFTER DLY_EN_OUT1 TIME DELAY
F
FAULT IN: LOW
UP: RISING EDGE
AFTER DLY_EN_OUT1
TIME DELAY
DISABLE OUT1
ENABLE OUT1
OUT1: LOW
OUT1: HIGH
FAULT IN: LOW
DOWN: FALLING EDGE
AFTER BLANKING DELAY VIN1: LOW
F
EXIT UVLO
F
AFTER BLANKING DELAY VIN1: HIGH
DELAY 2
FAULT IN: LOW
DOWN: FALLING EDGE
VIN1: LOW
F
AFTER DLY_EN_OUT2 TIME DELAY
F
FAULT IN: LOW
UP: RISING EDGE
VIN1: LOW
AFTER DLY_EN_OUT2
TIME DELAY
DISABLE OUT2
ENABLE OUT2
OUT2: LOW
OUT2: HIGH
FAULT IN: LOW
DOWN: FALLING EDGE
VIN1: LOW
AFTER BLANKING DELAY VIN2: LOW
F
AFTER BLANKING DELAY VIN2: HIGH
DELAY 3
FAULT IN: LOW
DOWN: FALLING EDGE
VIN1 OR VIN2: LOW
F
AFTER DLY_EN_OUT3 TIME DELAY
FAULT IN: LOW
UP: RISING EDGE
VIN1 OR VIN2: LOW
F
AFTER DLY_EN_OUT3
TIME DELAY
DISABLE OUT3
ENABLE OUT3
OUT3: LOW
OUT3: HIGH
FAULT IN: LOW
DOWN: FALLING EDGE
VIN1 OR VIN2: LOW
AFTER BLANKING DELAY VIN3: LOW
F
AFTER BLANKING DELAY VIN3: HIGH
DELAY 4
FAULT IN: LOW
DOWN: FALLING EDGE
VIN1 OR VIN2 OR VIN3: LOW
F
AFTER DLY_EN_OUT4 TIME DELAY
AFTER DLY_EN_OUT4
TIME DELAY
DISABLE OUT4
ENABLE OUT4
OUT4: LOW
OUT4: HIGH
FAULT IN: LOW
DOWN: FALLING EDGE
VIN1 OR VIN2 OR VIN3: LOW
AFTER BLANKING DELAY VIN4: LOW
F
AFTER BLANKING DELAY VIN4: HIGH
POWER-UP DONE
DOWN: FALLING EDGE
FAULT IN: LOW
UP: RISING EDGE
VIN1 OR VIN2 OR VIN3 OR VIN4: LOW
SEQ_DONE: HIGH
Figure 29. ADM1186-1 State Machine Operation
Rev. 0 | Page 18 of 28
F
07153-030
F
FAULT IN: LOW
UP: RISING EDGE
VIN1 OR VIN2 OR VIN3: LOW
ADM1186
VCC
ADM1186-2
VIN1
GLITCH FILTER
PWRGD
VIN2
GLITCH FILTER
VIN3
GLITCH FILTER
OUT1
VIN4
GLITCH FILTER
OUT2
0.6V
STATE
MACHINE
UP/DOWN
GLITCH FILTER
EDGE
DETECT
OUT3
1.4V
OUT4
14µA
DLY_EN_OUT2
DLY_EN_OUT3
DLY_EN_OUT4
BLANK_DLY
CAPACITOR MUX
AND DISCHARGE
450Ω
GND
Figure 30. Functional Block Diagram of the ADM1186-2
Rev. 0 | Page 19 of 28
07153-031
1.4V
ADM1186
WAIT START
OUT1: LOW OUT3: LOW
OUT2: LOW OUT4: LOW
UP/DOWN: LOW
UP/DOWN: RISING EDGE
F
UP/DOWN: RISING EDGE
CLEAR FAULT
UP/DOWN: FALLING EDGE
DISABLE OUT1
ENABLE OUT1 AFTER BLANKING DELAY VIN1: LOW
OUT1: LOW
OUT1: HIGH
AFTER BLANKING DELAY VIN1: HIGH
F
FAULT HOLD
TIMES OUT
SET FAULT
DELAY 2
UP/DOWN: FALLING EDGE
VIN1: LOW
F
OUT1: LOW OUT3: LOW
OUT2: LOW OUT4: LOW
AFTER DLY_EN_OUT2 TIME DELAY
F
UP/DOWN: RISING EDGE
VIN1: LOW
AFTER DLY_EN_OUT2
TIME DELAY
DISABLE OUT2
ENABLE OUT2
OUT2: LOW
OUT2: HIGH
UP/DOWN: FALLING EDGE
VIN1: LOW
AFTER BLANKING DELAY VIN2: LOW
F
EXIT UVLO
F
AFTER BLANKING DELAY VIN2: HIGH
DELAY 3
UP/DOWN: FALLING EDGE
VIN1 OR VIN2: LOW
F
AFTER DLY_EN_OUT3 TIME DELAY
F
UP/DOWN: RISING EDGE
VIN1 OR VIN2: LOW
AFTER DLY_EN_OUT3
TIME DELAY
DISABLE OUT3
ENABLE OUT3
OUT3: LOW
OUT3: HIGH
UP/DOWN: FALLING EDGE
VIN1 OR VIN2: LOW
AFTER BLANKING DELAY VIN3: LOW
F
AFTER BLANKING DELAY VIN3: HIGH
DELAY 4
UP/DOWN: FALLING EDGE
VIN1 OR VIN2 OR VIN3: LOW
F
AFTER DLY_EN_OUT4 TIME DELAY
AFTER DLY_EN_OUT4
TIME DELAY
DISABLE OUT4
ENABLE OUT4
OUT4: LOW
OUT4: HIGH
UP/DOWN: FALLING EDGE
VIN1 OR VIN2 OR VIN3: LOW
AFTER BLANKING DELAY VIN4: LOW
F
AFTER BLANKING DELAY VIN4: HIGH
UP/DOWN: FALLING EDGE
POWER-UP DONE
VIN1 OR VIN2 OR VIN3 OR VIN4: LOW
Figure 31. ADM1186-2 State Machine Operation
Rev. 0 | Page 20 of 28
F
07153-032
F
UP/DOWN: RISING EDGE
VIN1 OR VIN2 OR VIN3: LOW
ADM1186
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1
UP
DOWN
DLY_EN_OUT1
OUT1
DLY_EN_OUT2
OUT2
DLY_EN_OUT3
OUT3
DLY_EN_OUT4
OUT4
BLANK_DLY
SEQ_DONE
PWRGD
STATE NAMES
4 - DELAY 2
5 - ENABLE OUT2
6 - DELAY 3
7 - ENABLE OUT3
8 - DELAY 4
9 - ENABLE OUT4
10 - POWER-UP DONE
11 - DISABLE OUT4
12 - DISABLE OUT3
13 - DISABLE OUT2
14 - DISABLE OUT1
07153-033
1 - WAIT START
2 - DELAY 1
3 - ENABLE OUT1
Figure 32. ADM1186-1 Typical Power-Up and Power-Down Sequence Waveforms with Corresponding State Names
1
2
3
4
5
6
7
8
9
10
11
12
13
1
UP/DOWN
OUT1
DLY_EN_OUT2
OUT2
DLY_EN_OUT3
OUT3
DLY_EN_OUT4
OUT4
BLANK_DLY
1 - WAIT START
2 - ENABLE OUT1
3 - DELAY 2
4 - ENABLE OUT2
5 - DELAY 3
6 - ENABLE OUT3
STATE NAMES
7 - DELAY 4
8 - ENABLE OUT4
9 - POWER-UP DONE
10 - DISABLE OUT4
11 - DISABLE OUT3
12 - DISABLE OUT2
13 - DISABLE OUT1
Figure 33. ADM1186-2 Typical Power-Up and Power-Down Sequence Waveforms with Corresponding State Names
Rev. 0 | Page 21 of 28
07153-037
PWRGD
ADM1186
5V
5V
IN
ADP1706
EN
2.5V
OUT
5V
5V
IN
ADP2107
EN
OUT
3.3V AUX
1.8V
3.3V AUX
IN
ADP1821
3.3V AUX
EN
1µF
1.2V
OUT
5V
5V
IN
ADP1706
EN
100nF
VCC
OUT1
OUT2
OUT3
UP/DOWN
ADM1186-2
3.3V
OUT4
VIN1
VIN2
VIN3
VIN4
DLY_EN_OUT2
DLY_EN_OUT3
2.5V AUX
DLY_EN_OUT4
PWRGD
BLANK_DLY
GND
07153-034
SEQUENCE CONTROL
OUT
Figure 34. ADM1186-2 Typical Application
Rev. 0 | Page 22 of 28
ADM1186
CASCADING MULTIPLE DEVICES
Multiple ADM1186-1 devices can be cascaded in applications
that require more than four supplies to be sequenced and
monitored. When ADM1186-1 devices are cascaded, the
controlled power-up and power-down of all the cascaded
supplies is maintained using only three pins on each device.
There are several configurations for interconnecting these
devices. The most suitable configuration depends on the
application. Figure 35 and Figure 36 show two methods for
cascading multiple ADM1186-1 devices.
Figure 35 shows a single sequence of 12 supplies. The capacitors
used for timing are not shown in the figure for clarity. To ensure
controlled power-up and power-down sequencing of all 12 supplies, the following connections are made:
•
•
•
The UP pin of the first device and the DOWN pin of the
last device in the cascade chain are connected.
The SEQ_DONE pin of Device N is connected to the UP
pin of Device N + 1.
The SEQ_DONE pin of Device N is connected to the
DOWN pin of Device N − 1.
When the SEQUENCE CONTROL line goes high, Device A
begins the power-up sequence, turning on each enable output
in turn, with the associated delays, according to the state
machine. When Device A completes its power-up sequence, the
SEQ_DONE pin goes from low to high, initiating a power-up
sequence on Device B. When Device B completes its power-up
sequence, the Device B SEQ_DONE pin goes high, initiating a
power-up sequence on Device C. When Device C completes its
power-up sequence and all supplies are above the UV threshold,
the system POWER GOOD signal goes high.
If the SEQUENCE CONTROL line goes low, Device C starts a
power-down sequence, turning off its enable outputs. When all
Device C enable outputs are off, the SEQ_DONE pin on Device C
goes low, causing a high-to-low transition on the DOWN pin of
Device B. This transition initiates a power-down sequence on
Device B, which takes all its OUTx pins low, causing SEQ_DONE
to be taken low. This high-to-low transition is seen by Device A,
which starts its power-down sequence, thus completing the
ordered shutdown of the 12 supplies.
Note that the capacitor on the DLY_EN_OUT1 pin of Device B
(not shown in Figure 35) sets the sequence time delay between
the last supply of Device A and the first supply of Device B
being turned on and off.
Figure 36 shows two independent sequences of four supplies,
each with common status outputs. In this example, both devices
share the same sequence control signal, so they start their
power-up and power-down sequences at the same time. Both
devices must complete their power-up sequences before the
POWER GOOD signal goes high.
The FAULT pins of all devices in a cascade should be connected.
Connecting the FAULT pins ensures that an undervoltage fault
on one device, or an unexpected event such as a rising or falling
edge on the UP or DOWN pin, generates a fault condition on
all the other devices.
When an internal fault condition occurs on a device, it pulls its
FAULT pin low. This in turns causes the other ADM1186-1
devices to enter the SET FAULT state and pull their FAULT pins
low. Each device waits for the fault hold time to elapse and then
moves to the CLEAR FAULT state.
If the VCC supply for an ADM1186-1 drops below VUVLO, the
UVLO circuit becomes active, and the FAULT pin is pulled low.
This generates a fault condition on all other connected devices.
A device in the CLEAR FAULT state holds its FAULT pin low
until its UP input pin is low. The device then moves into the
WAIT ALL OK state and releases the FAULT pin.
If, for example, a UV fault occurs on a VINx pin during a
power-up sequence, the UP pin will be high on the first device
in the cascade. The first device in the cascade holds the FAULT
line low until the UP pin is brought low. All other devices will
have released their FAULT pins and will be in the WAIT ALL
OK state.
When the UP pin goes low, the first device releases its FAULT
pin so the FAULT line returns high, which allows all devices to
move together from the WAIT ALL OK state back into the
WAIT START state, ready for the next power-up sequence.
An external device such as a microcontroller, field programmable
gate array (FPGA), or an overtemperature sensor can cause a
fault condition by briefly bringing FAULT low. In this case, the
ADM1186-1 behaves as described. If the external device continues
to hold the FAULT line low, all the ADM1186-1 devices remain
in the WAIT ALL OK state, effectively preventing a power-up
sequence from starting.
Rev. 0 | Page 23 of 28
VIN3
VIN4
V3
V4
Rev. 0 | Page 24 of 28
EN1
EN4
OUT4
3.3V
V5
SEQ_DONE
GND
FAULT
OUT4
OUT3
OUT2
OUT1
SEQ_DONE
GND
UP
VIN4
VIN3
V7
V8
VIN2
V6
VIN1
DOWN PWRGD
FAULT
EN3
EN2
OUT3
OUT2
OUT1
DOWN PWRGD
UP
VIN2
VIN1
EN5
3.3V
V9
EN8
EN7
EN6
3.3V
V12
V11
V10
FAULT
OUT4
OUT3
OUT2
OUT1
SEQ_DONE
GND
DOWN PWRGD
UP
VIN4
VIN3
VIN2
VIN1
VCC
ADM1186-1C
VCC
ADM1186-1B
VCC
ADM1186-1A
V2
V1
SEQUENCE CONTROL
SUPPLIES
SCALED DOWN
WITH RESISTOR
DIVIDERS
3.3V
EN12
EN11
EN10
EN9
ENABLE
OUTPUTS TO
REGULATORS
WITH PULL-UPs
AS REQUIRED
3.3V
POWER
GOOD
ADM1186
Figure 35. Cascading Multiple ADM1186-1 Devices, Option 1
07153-035
ADM1186
3.3V
VCC
ADM1186-1A
SUPPLIES
SCALED
DOWN WITH
RESISTOR
DIVIDERS
V1
VIN1
V2
VIN2
V3
VIN3
V4
VIN4
UP
SEQUENCE CONTROL
OUT1
EN1
OUT2
EN2
OUT3
EN3
OUT4
EN4
ENABLE
OUTPUTS TO
REGULATORS
WITH PULL-UPs
AS REQUIRED
3.3V
FAULT
DOWN PWRGD
SEQ_DONE
GND
NO CONNECT
3.3V
VCC
ADM1186-1B
VIN1
V6
VIN2
V7
VIN3
V8
VIN4
UP
OUT1
EN5
OUT2
EN6
OUT3
EN7
OUT4
EN8
5V
FAULT
POWER
GOOD
DOWN PWRGD
SEQ_DONE
NO CONNECT
GND
Figure 36. Cascading Multiple ADM1186-1 Devices, Option 2
Rev. 0 | Page 25 of 28
07153-036
V5
ADM1186
OUTLINE DIMENSIONS
0.345 (8.76)
0.341 (8.66)
0.337 (8.55)
20
11
1
10
0.010 (0.25)
0.006 (0.15)
0.069 (1.75)
0.053 (1.35)
0.065 (1.65)
0.049 (1.25)
0.010 (0.25)
0.004 (0.10)
COPLANARITY
0.004 (0.10)
0.158 (4.01)
0.154 (3.91)
0.150 (3.81) 0.244 (6.20)
0.236 (5.99)
0.228 (5.79)
0.025 (0.64)
BSC
SEATING
PLANE
8°
0°
0.012 (0.30)
0.008 (0.20)
0.020 (0.51)
0.010 (0.25)
0.050 (1.27)
0.016 (0.41)
0.041 (1.04)
REF
COMPLIANT TO JEDEC STANDARDS MO-137-AD
012808-A
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETERS DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 37. 20-Lead Shrink Small Outline Package [QSOP] (RQ-20)
Dimensions shown in inches and (millimeters)
0.197 (5.00)
0.193 (4.90)
0.189 (4.80)
16
9
1
8
0.244 (6.20)
0.236 (5.99)
0.228 (5.79)
0.010 (0.25)
0.006 (0.15)
0.069 (1.75)
0.053 (1.35)
0.065 (1.65)
0.049 (1.25)
0.010 (0.25)
0.004 (0.10)
COPLANARITY
0.004 (0.10)
0.158 (4.01)
0.154 (3.91)
0.150 (3.81)
0.025 (0.64)
BSC
SEATING
PLANE
0.012 (0.30)
0.008 (0.20)
8°
0°
0.050 (1.27)
0.016 (0.41)
0.020 (0.51)
0.010 (0.25)
0.041 (1.04)
REF
012808-A
COMPLIANT TO JEDEC STANDARDS MO-137-AB
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETERS DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 38. 16-Lead Shrink Small Outline Package [QSOP] (RQ-16)
Dimensions shown in inches and (millimeters)
ORDERING GUIDE
Model
ADM1186-1ARQZ 1
ADM1186-1ARQZ-REEL1
ADM1186-2ARQZ1
ADM1186-2ARQZ-REEL1
EVAL-ADM1186-1EBZ1
EVAL-ADM1186-1MBZ1
EVAL-ADM1186-2EBZ1
EVAL-ADM1186-2MBZ1
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
20-Lead Shrink Small Outline Package [QSOP]
20-Lead Shrink Small Outline Package [QSOP]
16-Lead Shrink Small Outline Package [QSOP]
16-Lead Shrink Small Outline Package [QSOP]
Evaluation Kit
Micro-Evaluation Kit
Evaluation Kit
Micro-Evaluation Kit
Z = RoHS Compliant Part.
Rev. 0 | Page 26 of 28
Package Option
RQ-20
RQ-20
RQ-16
RQ-16
ADM1186
NOTES
Rev. 0 | Page 27 of 28
ADM1186
NOTES
©2008 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07153-0-5/08(0)
Rev. 0 | Page 28 of 28