AD ADN2813ACPZ

Continuous Rate 10 Mb/s to 1.25 Gb/s Clock and
Data Recovery IC with Integrated Limiting Amp
ADN2813
FEATURES
GENERAL DESCRIPTION
Serial data input: 10 Mb/s to 1.25 Gb/s
Exceeds SONET requirements for jitter transfer/
generation/tolerance
Quantizer sensitivity: 3.3 mV typ
Adjustable slice level: ±95 mV
Patented clock recovery architecture
Loss-of-signal (LOS) detect range: 2.3 mV to 19 mV
Independent slice level adjust and LOS detector
No reference clock required
Loss-of-lock indicator
I2C® interface to access optional features
Single-supply operation: 3.3 V
Low power: 450 mW typ
5 mm × 5 mm 32-lead LFCSP, Pb free
The ADN2813 provides the receiver functions of quantization,
signal level detect, and clock and data recovery for continuous
data rates from 10 Mb/s to 1.25 Gb/s. The ADN2813 automatically locks to all data rates without the need for an external
reference clock or programming. All SONET jitter requirements
are met, including jitter transfer, jitter generation, and jitter
tolerance. All specifications are quoted for −40°C to +85°C
ambient temperature, unless otherwise noted.
This device, together with a PIN diode and a TIA preamplifier,
can implement a highly integrated, low cost, low power fiber
optic receiver.
The receiver front-end, loss-of-signal (LOS) detector circuit
indicates when the input signal level has fallen below a useradjustable threshold. The LOS detect circuit has hysteresis to
prevent chatter at the output.
APPLICATIONS
SONET OC-1/-3/-12 and all associated FEC rates
Fibre Channel, GbE, HDTVs
WDM transponders
Regenerators/repeaters
Test equipment
Broadband cross-connects and routers
The ADN2813 is available in a compact 5 mm × 5 mm,
32-lead LFCSP.
FUNCTIONAL BLOCK DIAGRAM
REFCLKP/N
(OPTIONAL)
SLICEP/N
LOL
2
CF1
CF2
FREQUENCY
DETECT
LOOP
FILTER
PHASE
DETECT
LOOP
FILTER
VCC
VEE
PIN
NIN
QUANTIZER
PHASE
SHIFTER
VCO
VREF
DATA
RE-TIMING
2
2
THRADJ
LOS
DATAOUTP/N
CLKOUTP/N
ADN2813
04951-0-001
LOS
DETECT
Figure 1.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
© 2005 Analog Devices, Inc. All rights reserved.
ADN2813
TABLE OF CONTENTS
Features .............................................................................................. 1
Theory of Operation ...................................................................... 14
Applications....................................................................................... 1
Functional Description.................................................................. 16
General Description ......................................................................... 1
Frequency Acquisition............................................................... 16
Functional Block Diagram .............................................................. 1
Limiting Amplifier ..................................................................... 16
Revision History ............................................................................... 2
Slice Adjust.................................................................................. 16
Specifications..................................................................................... 3
Loss-of-Signal (LOS) Detector ................................................. 16
Jitter Specifications....................................................................... 4
Lock Detector Operation .......................................................... 16
Output and Timing Specifications ............................................. 5
Harmonic Detector .................................................................... 17
Absolute Maximum Ratings............................................................ 6
SQUELCH Mode........................................................................ 18
Thermal Characteristics .............................................................. 6
I2C Interface ................................................................................ 18
ESD Caution.................................................................................. 6
Reference Clock (Optional) ...................................................... 18
Timing Characteristics..................................................................... 7
Applications Information .............................................................. 21
Pin Configuration and Function Descriptions............................. 8
PCB Design Guidelines ............................................................. 21
Typical Performance Characteristics ............................................. 9
DC-Coupled Application .......................................................... 23
I2C Interface Timing and Internal Register Description........... 10
Coarse Data Rate Readback Look-Up Table............................... 24
Terminology .................................................................................... 12
Outline Dimensions ....................................................................... 26
Jitter Specifications ......................................................................... 13
Ordering Guide .......................................................................... 26
REVISION HISTORY
9/05—Revision 0: Initial Version
Rev. 0 | Page 2 of 28
ADN2813
SPECIFICATIONS
TA = TMIN to TMAX, VCC = VMIN to VMAX, VEE = 0 V, CF = 0.47 μF, SLICEP = SLICEN = VEE, input data pattern: PRBS 223 − 1,
unless otherwise noted.
Table 1.
Parameter
QUANTIZER—DC CHARACTERISTICS
Input Voltage Range
Peak-to-Peak Differential Input
Input Common-Mode Level
Differential Input Sensitivity
Input Offset
Input RMS Noise
QUANTIZER—AC CHARACTERISTICS
Data Rate
S11
Input Resistance
Input Capacitance
QUANTIZER—SLICE ADJUSTMENT
Gain
Differential Control Voltage Input
Control Voltage Range
Slice Threshold Offset
LOSS-OF-SIGNAL (LOS) DETECT
Loss-of-Signal Detect Range (see Figure 6)
Hysteresis (Electrical)
LOS Assert Time
LOS Deassert Time
LOSS-OF-LOCK (LOL) DETECT
VCO Frequency Error for LOL Assert
VCO Frequency Error for LOL Deassert
LOL Response Time
ACQUISITION TIME
Lock-to-Data Mode
Optional Lock to REFCLK Mode
DATA RATE READBACK ACCURACY
Coarse Readback
Fine Readback
Conditions
Min
@ PIN or NIN, dc-coupled
PIN − NIN
DC-coupled (see Figure 27, Figure 28, and Figure 29)
223 − 1 PRBS, ac-coupled, 1 BER = 1 × 10–10
1.8
2.3
6
BER = 1 × 10–10
Typ
2.5
3.3
500
290
10
@ 2.5 GHz
Differential
Max
Unit
2.8
2.0
2.8
V
V
V
mV p-p
μV
μV rms
1250
Mb/s
dB
Ω
pF
0.13
+0.95
0.95
V/V
V
V
mV
−15
100
0.65
SLICEP – SLICEN = ±0.5 V
SLICEP – SLICEN
DC level @ SLICEP or SLICEN
0.10
−0.95
VEE
0.11
1
RTHRESH = 0 Ω
RTHRESH = 100 kΩ
GbE
RTHRESH = 0 Ω
RTHRESH = 100 kΩ
OC-1
RTHRESH = 0 Ω
RTHRESH = 10 kΩ
DC-coupled 2
DC-coupled2
14
2.3
16.5
3.5
19
4.7
mV
mV
6.4
4.6
7.2
6.2
8.0
7.8
dB
dB
5.5
3.1
6.6
5.4
500
400
7.7
7.7
dB
dB
ns
ns
With respect to nominal
With respect to nominal
10 Mb/s
OC-12
GbE
1000
250
5
200
200
ppm
ppm
ms
μs
μs
GbE
OC-12
OC-3
OC-1
10 Mb/s
1.5
2.0
3.4
9.8
40.0
20.0
ms
ms
ms
ms
ms
ms
See Table 13
In addition to REFCLK accuracy
Data rate ≤ 20 Mb/s
Data rate > 20 Mb/s
10
%
Rev. 0 | Page 3 of 28
200
100
ppm
ppm
ADN2813
Parameter
POWER SUPPLY VOLTAGE
POWER SUPPLY CURRENT
OPERATING TEMPERATURE RANGE
1
2
Conditions
Min
3.0
Locked to 1.25 Gb/s
–40
Typ
3.3
139
Max
3.6
155
+85
Unit
V
mA
°C
PIN and NIN should be differentially driven and ac-coupled for optimum sensitivity.
When ac-coupled, the LOS assert and deassert times are dominated by the RC time constant of the ac coupling capacitor and the 50 Ω input termination of the
ADN2813 input stage.
JITTER SPECIFICATIONS
TA = TMIN to TMAX, VCC = VMIN to VMAX, VEE = 0 V, CF = 0.47 μF, SLICEP = SLICEN = VEE, input data pattern: PRBS 223 − 1,
unless otherwise noted.
Table 2.
Parameter
PHASE-LOCKED LOOP CHARACTERISTICS
Jitter Transfer BW
Jitter Peaking
Jitter Generation
Conditions
Min
OC-12
OC-3
OC-12
OC-3
OC-12, 12 kHz to 5 MHz
OC-3, 12 kHz to 1.3 MHz
Jitter Tolerance
1
1 GbE, IEEE 802.3
637 kHz
OC-12, 223 − 1 PRBS
30 Hz 1
300 Hz1
25 kHz
250 kHz1
OC-3, 223 − 1 PRBS
30 Hz1
300 Hz1
6500 Hz
65 kHz1
Max
Unit
75
26
0
0
0.001
0.011
0.001
0.005
130
42
0.03
0.03
0.003
0.026
0.002
0.010
kHz
kHz
dB
dB
UI rms
UI p-p
UI rms
UI p-p
0.749
UI p-p
100
44
2.5
1.0
UI p-p
UI p-p
UI p-p
UI p-p
50
23.5
3.5
1.0
UI p-p
UI p-p
UI p-p
UI p-p
Jitter tolerance of the ADN2813 at these jitter frequencies is better than what the test equipment is able to measure.
Rev. 0 | Page 4 of 28
Typ
ADN2813
OUTPUT AND TIMING SPECIFICATIONS
Table 3.
Parameter
LVDS OUTPUT CHARACTERISTICS
(CLKOUTP/CLKOUTN, DATAOUTP/DATAOUTN)
Output Voltage High
Output Voltage Low
Differential Output Swing
Differential Output Swing
Output Offset Voltage
Output Impedance
LVDS Outputs Timing
Rise Time
Fall Time
Setup Time
Hold Time
I2C INTERFACE DC CHARACTERISTICS
Input High Voltage
Input Low Voltage
Input Current
Output Low Voltage
I2C INTERFACE TIMING
SCK Clock Frequency
SCK Pulse Width High
SCK Pulse Width Low
Start Condition Hold Time
Start Condition Setup Time
Data Setup Time
Data Hold Time
SCK/SDA Rise/Fall Time
Stop Condition Setup Time
Bus Free Time Between a Stop and a Start
REFCLK CHARACTERISTICS
Input Voltage Range
Minimum Differential Input Drive
Reference Frequency
Required Accuracy
LVTTL DC INPUT CHARACTERISTICS
Input High Voltage
Input Low Voltage
Input High Current
Input Low Current
LVTTL DC OUTPUT CHARACTERISTICS
Output High Voltage
Output Low Voltage
1
Conditions
VOH (see Figure 3), 655 Mb/s
VOL (see Figure 3), 655 Mb/s
VOD (see Figure 3), 655 Mb/s
VOD (see Figure 3), 1.25 Gb/s
VOS (see Figure 3)
Differential
GbE
20% to 80%
80% to 20%
TS (see Figure 2), GbE
TH (see Figure 2), GbE
LVCMOS
VIH
VIL
VIN = 0.1 VCC or VIN = 0.9 VCC
VOL, IOL = 3.0 mA
See Figure 11
Min
925
250
240
1125
360
360
Typ
Max
Unit
1475
mV
mV
mV
320
300
1200
100
400
400
1275
115
115
400
400
220
220
440
440
ps
ps
ps
ps
0.3 VCC
+10.0
0.4
V
V
μA
V
0.7 VCC
−10.0
400
tHIGH
tLOW
tHD;STA
tSU;STA
tSU;DAT
tHD;DAT
TR/TF
tSU;STO
tBUF
Optional lock to REFCLK mode
@ REFCLKP or REFCLKN
VIL
VIH
600
1300
600
600
100
300
20 + 0.1 Cb 1
600
1300
300
0
VCC
100
10
160
100
VIH
VIL
IIH, VIN = 2.4 V
IIL, VIN = 0.4 V
2.0
VOH, IOH = −2.0 mA
VOL, IOL = 2.0 mA
2.4
Cb = total capacitance of one bus line in pF. If mixed with Hs mode devices, faster fall times are allowed.
Rev. 0 | Page 5 of 28
0.8
5
−5
0.4
mV
Ω
kHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
V
V
mV p-p
MHz
ppm
V
V
μA
μA
V
V
ADN2813
ABSOLUTE MAXIMUM RATINGS
TA = TMIN to TMAX, VCC = VMIN to VMAX, VEE = 0 V, CF =
0.47 μF, SLICEP = SLICEN = VEE, unless otherwise noted.
THERMAL CHARACTERISTICS
Table 4.
Parameter
Supply Voltage (VCC)
Minimum Input Voltage (All Inputs)
Maximum Input Voltage (All Inputs)
Maximum Junction Temperature
Storage Temperature Range
Rating
4.2 V
VEE − 0.4 V
VCC + 0.4 V
125°C
−65°C to +150°C
Thermal Resistance
32-LFCSP, 4-layer board with exposed paddle soldered to VEE,
θJA = 28°C/W.
Stress above those listed under Absolute Maximum Ratings may
cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other
conditions above those indicated in the operational sections of
this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 6 of 28
ADN2813
TIMING CHARACTERISTICS
CLKOUTP
TH
04951-0-002
TS
DATAOUTP/N
Figure 2. Output Timing
DIFFERENTIAL CLKOUTP/N, DATAOUTP/N
VOH
VOS
04951-0-032
|VOD|
VOL
Figure 3. Differential Output Specifications
5mA
RLOAD
100Ω
VDIFF
100Ω
SIMPLIFIED LVDS
OUTPUT STAGE
Figure 4. Differential Output Stage
Rev. 0 | Page 7 of 28
04951-0-033
5mA
ADN2813
32 TEST2
31 VCC
30 VEE
29 DATAOUTP
28 DATAOUTN
27 SQUELCH
26 CLKOUTP
25 CLKOUTN
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
ADN2813*
TOP VIEW
(Not to Scale)
24 VCC
23 VEE
22 LOS
21 SDA
20 SCK
19 SADDR5
18 VCC
17 VEE
04951-0-004
PIN 1
INDICATOR
THRADJ 9
REFCLKP 10
REFCLKN 11
VCC 12
VEE 13
CF2 14
CF1 15
LOL 16
TEST1 1
VCC 2
VREF 3
NIN 4
PIN 5
SLICEP 6
SLICEN 7
VEE 8
* THERE IS AN EXPOSED PAD ON THE BOTTOM OF
THE PACKAGE THAT MUST BE CONNECTED TO GND.
Figure 5. Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Exposed Pad
1
Mnemonic
TEST1
VCC
VREF
NIN
PIN
SLICEP
SLICEN
VEE
THRADJ
REFCLKP
REFCLKN
VCC
VEE
CF2
CF1
LOL
VEE
VCC
SADDR5
SCK
SDA
LOS
VEE
VCC
CLKOUTN
CLKOUTP
SQUELCH
DATAOUTN
DATAOUTP
VEE
VCC
TEST2
Pad
Type 1
P
AO
AI
AI
AI
AI
P
AI
DI
DI
P
P
AO
AO
DO
P
P
DI
DI
DI
DO
P
P
DO
DO
DI
DO
DO
P
P
P
Description
Connect to VCC.
Power for Limiting Amplifier, LOS.
Internal VREF Voltage. Decouple to GND with a 0.1 μF capacitor.
Differential Data Input. CML.
Differential Data Input. CML.
Differential Slice Level Adjust Input.
Differential Slice Level Adjust Input.
GND for Limiting Amplifier, LOS.
LOS Threshold Setting Resistor.
Differential REFCLK Input. 10 MHz to 160 MHz.
Differential REFCLK Input. 10 MHz to 160 MHz.
VCO Power.
VCO GND.
Frequency Loop Capacitor.
Frequency Loop Capacitor.
Loss-of-Lock Indicator. LVTTL active high.
FLL Detector GND.
FLL Detector Power.
Slave Address Bit 5.
I2C Clock Input.
I2C Data Input.
Loss-of-Signal Detect Output. Active high. LVTTL.
Output Buffer, I2C GND.
Output Buffer, I2C Power.
Differential Recovered Clock Output. LVDS.
Differential Recovered Clock Output. LVDS.
Disable Clock and Data Outputs. Active high. LVTTL.
Differential Recovered Data Output. LVDS.
Differential Recovered Data Output. LVDS.
Phase Detector, Phase Shifter GND.
Phase Detector, Phase Shifter Power.
Connect to VCC.
Connect to GND.
Type: P = power, AI = analog input, AO = analog output, DI = digital input, DO = digital output.
Rev. 0 | Page 8 of 28
ADN2813
TYPICAL PERFORMANCE CHARACTERISTICS
16
12
10
8
6
4
04951-0-005
TRIP POINT (mV p-p)
14
2
1
10
100
1k
10k
100k
RTH (Ω)
Figure 6. LOS Comparator Trip Point Programming
Rev. 0 | Page 9 of 28
ADN2813
I2C INTERFACE TIMING AND INTERNAL REGISTER DESCRIPTION
R/W
CTRL.
SLAVE ADDRESS [6...0]
A5
SET BY
PIN 19
0
0
0
0
0
X
04951-0-007
1
MSB = 1
0 = WR
1 = RD
S
SLAVE ADDR, LSB = 0 (WR) A(S) SUB ADDR A(S) DATA A(S)
DATA A(S)
P
04951-0-008
Figure 7. Slave Address Configuration
2
S
SLAVE ADDR, LSB = 0 (WR) A(S) SUB ADDR A(S) S SLAVE ADDR, LSB = 1 (RD) A(S) DATA A(M)
S = START BIT
A(S) = ACKNOWLEDGE BY SLAVE
DATA A(M) P
P = STOP BIT
A(M) = LACK OF ACKNOWLEDGE BY MASTER
A(M) = ACKNOWLEDGE BY MASTER
04951-0-009
Figure 8. I C Write Data Transfer
Figure 9. I2C Read Data Transfer
SDA
SLAVE ADDRESS
A6
SUB ADDRESS
A5
STOP BIT
DATA
A7
A0
D7
D0
SCK
S
WR
ACK
ACK
SLADDR[4...0]
ACK
SUB ADDR[6...1]
DATA[6...1]
Figure 10. I2C Data Transfer Timing
tF
tSU;DAT
tHD;STA
tBUF
SDA
tR
tR
tSU;STO
tF
tLOW
tHIGH
tHD;STA
S
tSU;STA
S
tHD;DAT
Figure 11. I2C Port Timing Diagram
Rev. 0 | Page 10 of 28
P
S
04951-0-011
SCK
P
04951-0-010
START BIT
ADN2813
Table 6. Internal Register Map 1
Reg.
Name
FREQ0
FREQ1
FREQ2
RATE
R/W
R
R
R
R
Address
0x0
0x1
0x2
0x3
D7
MSB
MSB
0
MISC
R
0x4
x
CTRLA
W
0x8
CTRLB
W
0x9
Config.
LOL
Reset
MISC[4]
System
Reset
0
Reset
MISC[2]
0
0
0
CTRLC
W
0x11
0
0
0
0
0
Config. LOS
SQUELCH
Mode
Output Boost
1
D6
D5
D4
MSB
COARSE_RD[8] MSB
LOS
Status
x
FREF Range
D3
D2
D1
Coarse Data Rate Readback
Data Rate
Static
LOL
Measure
LOL
Status
Complete
D0
LSB
LSB
LSB
COARSE_RD[1]
x
COARSE_RD[0] LSB
Measure
Data Rate
Data Rate/DIV_FREF Ratio
Lock to
Reference
All writeable registers default to 0x00.
Table 7. Miscellaneous Register, MISC
D7
x
D6
x
LOS Status
D5
0 = No loss of signal
1 = Loss of signal
Static LOL
D4
0 = Waiting for next LOL
1 = Static LOL until reset
LOL Status
D3
0 = Locked
1 = Acquiring
Data Rate Measurement
Complete
D2
0 = Measuring data rate
1 = Measurement complete
D1
x
Coarse Rate
Readback LSB
D0
COARSE_RD[0]
Table 8. Control Register, CTRLA 1
FREF Range
D7 D6
0
0
0
1
1
0
1
1
1
Data Rate/Div_FREF Ratio
D5 D4 D3 D2
0
0
0
0
1
0
0
0
1
2
0
0
1
0
4
n
2n
1
0
0
0
256
10 MHz to 20 MHz
20 MHz to 40 MHz
40 MHz to 80 MHz
80 MHz to 160 MHz
Measure Data Rate
D1
Set to 1 to measure data rate
Lock to Reference
D0
0 = Lock to input data
1 = Lock to reference clock
Where DIV_FREF is the divided down reference referred to the 10 MHz to 20 MHz band (see the Reference Clock (Optional) section).
Table 9. Control Register, CTRLB
Config LOL
D7
0 = LOL pin normal operation
1 = LOL pin is static LOL
Reset MISC[4]
D6
Write a 1 followed by
0 to reset MISC[4]
System Reset
D5
Write a 1 followed by 0
to reset ADN2813
D4
Set
to 0
Reset MISC[2]
D3
Write a 1 followed by 0
to reset MISC[2]
D2
Set
to 0
D1
Set
to 0
D0
Set
to 0
Table 10. Control Register, CTRLC
D7
Set to 0
D6
Set to 0
D5
Set to 0
D4
Set to 0
D3
Set to 0
Config. LOS
D2
0 = Active high LOS
1 = Active low LOS
Rev. 0 | Page 11 of 28
SQUELCH Mode
D1
0 = SQUELCH CLK and DATA
1 = SQUELCH CLK or DATA
Output Boost
D0
0 = Default output swing
1 = Boost output swing
ADN2813
TERMINOLOGY
OUTPUT
NOISE
1
10mV p-p
VREF
SCOPE
PROBE
ADN2813
PIN
+
QUANTIZER
–
50Ω
50Ω
VREF
2.5V
3kΩ
04951-0-013
Input Sensitivity and Input Overdrive
Sensitivity and overdrive specifications for the quantizer involve
offset voltage, gain, and noise. The relationship between the
logic output of the quantizer and the analog voltage input is
shown in Figure 12. For sufficiently large positive input voltage,
the output is always Logic 1, and similarly for negative inputs,
the output is always Logic 0. However, the transitions between
output Logic 1 and output Logic 0 are not at precisely defined
input voltage levels but occur over a range of input voltages.
Within this range of input voltages, the output may be either 1
or 0, or it may even fail to attain a valid logic state. The width of
this zone is determined by the input voltage noise of the
quantizer. The center of the zone is the quantizer input offset
voltage. Input overdrive is the magnitude of signal required to
guarantee the correct logic level with 1 × 10−10 confidence level.
Figure 13. Single-Ended Sensitivity Measurement
Driving the ADN2813 differentially (see Figure 14), sensitivity
seems to improve from observing the quantizer input with an
oscilloscope probe. This is an illusion caused by the use of a
single-ended probe. A 5 mV p-p signal appears to drive the
ADN2813 quantizer. However, the single-ended probe
measures only half the signal. The true quantizer input signal is
twice this value, because the other quantizer input is a
complementary signal to the signal being observed.
5mV p-p
0
SCOPE
PROBE
VREF
INPUT (V p-p)
OVERDRIVE
+
04951-0-012
SENSITIVITY
(2× OVERDRIVE)
PIN
QUANTIZER
NIN
Figure 12. Input Sensitivity and Input Overdrive
Single-Ended vs. Differential
AC coupling is typically used to drive the inputs to the
quantizer. The inputs are internally dc biased to a commonmode potential of ~2.5 V. Driving the ADN2813 single-ended
and observing the quantizer input with an oscilloscope probe at
the point indicated in Figure 13 shows a binary signal with an
average value equal to the common-mode potential and
instantaneous values both above and below the average value. It
is convenient to measure the peak-to-peak amplitude of this
signal and call the minimum required value the quantizer
sensitivity. Referring to Figure 13, because both positive and
negative offsets need to be accommodated, the sensitivity is
twice the overdrive. The ADN2813 quantizer typically has
3.3 mV p-p sensitivity.
–
50Ω
VREF
5mV p-p
50Ω
VREF
2.5V
3kΩ
04951-0-014
OFFSET
Figure 14. Differential Sensitivity Measurement
LOS Response Time
LOS response time is the delay between removal of the input
signal and indication of loss of signal (LOS) at the LOS output,
Pin 22. When the inputs are dc-coupled, the LOS assert time of
the ADN2813 is 500 ns typical and the deassert time is 400 ns
typical. In practice, the time constant produced by the ac
coupling at the quantizer input and the 50 Ω on-chip input
termination determines the LOS response time.
Rev. 0 | Page 12 of 28
ADN2813
JITTER SPECIFICATIONS
The ADN2813 CDR is designed to achieve the best biterror-rate (BER) performance and to exceed the jitter
transfer, generation, and tolerance specifications proposed
for SONET/SDH equipment defined in the Telcordia
Technologies specification.
Jitter Generation
The jitter generation specification limits the amount of jitter
that can be generated by the device with no jitter and wander
applied at the input. For SONET devices, the jitter generated
must be less than 0.01 UI rms and must be less than 0.1 UI p-p.
Jitter Transfer
The jitter transfer function is the ratio of the jitter on the output
signal to the jitter applied on the input signal vs. the frequency.
This parameter measures the limited amount of the jitter on an
input signal that can be transferred to the output signal (see
Figure 15).
04951-0-015
fC
JITTER FREQUENCY (kHz)
Figure 15. Jitter Transfer Curve
Jitter Tolerance
The jitter tolerance is defined as the peak-to-peak amplitude of
the sinusoidal jitter applied on the input signal, which causes a
1 dB power penalty. This is a stress test intended to ensure that
no additional penalty is incurred under the operating conditions
(see Figure 16).
15.00
SLOPE = –20dB/DECADE
1.50
0.15
f0
f1
f2
f3
JITTER FREQUENCY (kHz)
Figure 16. SONET Jitter Tolerance Mask
Rev. 0 | Page 13 of 28
f4
04951-0-016
The following sections briefly summarize the specifications of
jitter generation, transfer, and tolerance in accordance with the
Telcordia document (GR-253-CORE, Issue 3, September 2000)
for the optical interface at the equipment level and the ADN2813
performance with respect to those specifications.
SLOPE = –20dB/DECADE
ACCEPTABLE
RANGE
INPUT JITTER AMPLITUDE (UI p-p)
Jitter is the dynamic displacement of digital signal edges from
their long-term average positions, measured in unit intervals
(UI), where 1 UI = 1 bit period. Jitter on the input data can
cause dynamic phase errors on the recovered clock sampling
edge. Jitter on the recovered clock causes jitter on the
retimed data.
JITTER GAIN (dB)
0.1
ADN2813
THEORY OF OPERATION
Another view of the circuit is that the phase shifter implements
the zero required for frequency compensation of a second-order
phase-locked loop, and this zero is placed in the feedback path
and, thus, does not appear in the closed-loop transfer function.
Jitter peaking in a conventional second-order phase-locked loop
is caused by the presence of this zero in the closed-loop transfer
function. Because this circuit has no zero in the closed-loop
transfer, jitter peaking is minimized.
The delay and phase loops together simultaneously provide
wideband jitter accommodation and narrow-band jitter
filtering. The linearized block diagram in Figure 17 shows that
the jitter transfer function, Z(s)/X(s), is a second-order low-pass
providing excellent filtering. Note that the jitter transfer has no
zero, unlike an ordinary second-order phase-locked loop. This
means that the main PLL loop has virtually zero jitter peaking
(see Figure 18). This makes this circuit ideal for signal regenerator applications where jitter peaking in a cascade of
regenerators can contribute to hazardous jitter accumulation.
The error transfer, e(s)/X(s), has the same high-pass form as an
ordinary phase-locked loop. This transfer function is free to be
optimized to give excellent wideband jitter accommodation,
because the jitter transfer function, Z(s)/X(s), provides the
narrow-band jitter filtering.
INPUT
DATA
e(s)
X(s)
d/sc
o/s
1/n
Z(s)
RECOVERED
CLOCK
d = PHASE DETECTOR GAIN
o = VCO GAIN
c = LOOP INTEGRATOR
psh = PHASE SHIFTER GAIN
n = DIVIDE RATIO
JITTER TRANSFER FUNCTION
Z(s)
1
=
cn
X(s)
n psh
s2
+1
+s
do
o
04951-0-017
TRACKING ERROR TRANSFER FUNCTION
e(s)
s2
=
d psh do
X(s)
+
s2 + s
c
cn
Figure 17. ADN2813 PLL/DLL Architecture
JITTER PEAKING
IN ORDINARY PLL
ADN2813
Z(s)
X(s)
o
n psh
d psh
c
04951-0-018
The delay and phase loops together track the phase of the input
data signal. For example, when the clock lags input data, the
phase detector drives the VCO to a higher frequency and
increases the delay through the phase shifter; both of these
actions serve to reduce the phase error between the clock and
data. The faster clock picks up phase, while the delayed data
loses phase. Because the loop filter is an integrator, the static
phase error is driven to zero.
psh
JITTER GAIN (dB)
The ADN2813 is a delay- and phase-locked loop circuit for
clock recovery and data retiming from an NRZ encoded data
stream. The phase of the input data signal is tracked by two
separate feedback loops that share a common control voltage. A
high speed delay-locked loop path uses a voltage controlled
phase shifter to track the high frequency components of input
jitter. A separate phase control loop, comprised of the VCO,
tracks the low frequency components of input jitter. The initial
frequency of the VCO is set by yet a third loop, which compares
the VCO frequency with the input data frequency and sets the
coarse tuning voltage. The jitter tracking phase-locked loop
controls the VCO by the fine-tuning control.
FREQUENCY (kHz)
Figure 18. ADN2813 Jitter Response vs. Conventional PLL
The delay and phase loops contribute to overall jitter accommodation. At low frequencies of input jitter on the data signal,
the integrator in the loop filter provides high gain to track large
jitter amplitudes with small phase error. In this case, the VCO is
frequency modulated, and jitter is tracked as in an ordinary
phase-locked loop. The amount of low frequency jitter that can
be tracked is a function of the VCO tuning range. A wider
tuning range gives larger accommodation of low frequency
jitter. The internal loop control voltage remains small for small
phase errors; therefore, the phase shifter remains close to the
center of its range and thus contributes little to the low
frequency jitter accommodation.
Rev. 0 | Page 14 of 28
ADN2813
At medium jitter frequencies, the gain and tuning range of the
VCO are not large enough to track input jitter. In this case, the
VCO control voltage becomes large and saturates, and the VCO
frequency dwells at one extreme of its tuning range or at the
other. The size of the VCO tuning range, therefore, has only a
small effect on the jitter accommodation. The delay-locked loop
control voltage is now larger, and therefore the phase shifter
takes on the burden of tracking the input jitter. The phase
shifter range, in UI, can be seen as a broad plateau on the jitter
tolerance curve. The phase shifter has a minimum range of 2 UI
at all data rates.
The gain of the loop integrator is small for high jitter
frequencies; therefore, larger phase differences are needed to
make the loop control voltage large enough to tune the range of
the phase shifter. Large phase errors at high jitter frequencies
cannot be tolerated. In this region, the gain of the integrator
determines the jitter accommodation. Because the gain of the
loop integrator declines linearly with frequency, jitter accommodation is lower with higher jitter frequency. At the highest
frequencies, the loop gain is very small, and little tuning of the
phase shifter can be expected. In this case, jitter accommodation is
determined by the eye opening of the input data, the static
phase error, and the residual loop jitter generation. The jitter
accommodation is roughly 0.5 UI in this region. The corner
frequency between the declining slope and the flat region is
the closed loop bandwidth of the delay-locked loop, which is
roughly 1.5 MHz at 1.25 Gb/s.
Rev. 0 | Page 15 of 28
ADN2813
FUNCTIONAL DESCRIPTION
FREQUENCY ACQUISITION
LOSS-OF-SIGNAL (LOS) DETECTOR
The ADN2813 acquires frequency from the data over a range of
data frequencies from 10 Mb/s to 1.25 Gb/s. The lock detector
circuit compares the frequency of the VCO and the frequency
of the incoming data. When these frequencies differ by more
than 1000 ppm, LOL is asserted. This initiates a frequency
acquisition cycle. The VCO frequency is reset to the bottom of
its range, which is 10 MHz. The frequency detector then
compares this VCO frequency and the incoming data frequency
and increments the VCO frequency, if necessary. Initially, the
VCO frequency is incremented in large steps to aid fast acquisition. As the VCO frequency approaches the data frequency, the
step size is reduced until the VCO frequency is within 250 ppm
of the data frequency, at which point LOL is deasserted.
The receiver front-end LOS detector circuit detects when the
input signal level has fallen below a user-adjustable threshold.
The threshold is set with a single external resistor from Pin 9,
THRADJ, to VEE. The LOS comparator trip point vs. the
resistor value is illustrated in Figure 6. If the input level to the
ADN2813 drops below the programmed LOS threshold, the
output of the LOS detector, LOS Pin 22, is asserted to a Logic 1.
The LOS detector’s response time is ~500 ns by design but is
dominated by the RC time constant in ac-coupled applications.
The LOS pin defaults to active high. However, by setting
Bit CTRLC[2] to 1, the LOS pin is configured as active low.
LIMITING AMPLIFIER
The limiting amplifier has differential inputs (PIN/NIN),
which are internally terminated with 50 Ω to an on-chip voltage
reference (VREF = 2.5 V typically). The inputs are typically
ac-coupled externally, although dc coupling is possible as long
as the input common-mode voltage remains above 2.5 V (see
Figure 27 to Figure 29 in the Applications Information section).
Input offset is factory trimmed to achieve better than 3.3 mV
typical sensitivity with minimal drift. The limiting amplifier can
be driven differentially or single-ended.
SLICE ADJUST
The quantizer slicing level can be offset by ±100 mV to mitigate
the effect of amplified spontaneous emission (ASE) noise or
duty cycle distortion by applying a differential voltage input of
up to ±0.95 V to SLICEP/SLICEN inputs. If no adjustment of
the slice level is needed, SLICEP/SLICEN should be tied to
VEE. The gain of the slice adjustment is ~0.11 V/V.
LOS OUTPUT
INPUT LEVEL
HYSTERESIS
LOS THRESHOLD
t
04951-0-019
The frequency loop requires a single external capacitor between
CF1 and CF2, Pin 14 and Pin 15. A 0.47 μF ± 20%, X7R ceramic
chip capacitor with < 10 nA leakage current is recommended.
Leakage current of the capacitor can be calculated by dividing
the maximum voltage across the 0.47 μF capacitor, ~3 V, by the
insulation resistance of the capacitor. The insulation resistance
of the 0.47 μF capacitor should be greater than 300 MΩ.
INPUT VOLTAGE (VDIFF)
Once LOL is deasserted, the frequency-locked loop is turned
off. The PLL/DLL pulls in the VCO frequency the rest of the
way until the VCO frequency equals the data frequency.
There is typically 6 dB of electrical hysteresis designed into the
LOS detector to prevent chatter on the LOS pin. If the input
level drops below the programmed LOS threshold causing the
LOS pin to assert, the LOS pin is not deasserted until the input
level has increased to 6 dB (2×) above the LOS threshold (see
Figure 19).
Figure 19. LOS Detector Hysteresis
The LOS detector and the SLICE level adjust can be used
simultaneously on the ADN2813. This means that any offset
added to the input signal by the SLICE adjust pins does not
affect the LOS detector’s measurement of the absolute input
level.
LOCK DETECTOR OPERATION
The lock detector on the ADN2813 has three modes of
operation: normal mode, REFCLK mode, and static LOL mode.
Normal Mode
In normal mode, the ADN2813 is a continuous rate CDR that
locks onto any data rate from 10 Mb/s to 1.25 Gb/s without the
use of a reference clock as an acquisition aid. In this mode, the
lock detector monitors the frequency difference between the
VCO and the input data frequency and deasserts the loss-oflock signal, which appears on Pin 16, LOL, when the VCO is
within 250 ppm of the data frequency. This enables the D/PLL,
which pulls the VCO frequency in the remaining amount and
Rev. 0 | Page 16 of 28
ADN2813
acquires phase lock. Once locked, if the input frequency error
exceeds 1000 ppm (0.1%), the loss-of-lock signal is reasserted
and control returns to the frequency loop, which begins a new
frequency acquisition starting at the lowest point in the VCO
operating range, 10 MHz. The LOL pin remains asserted until
the VCO locks onto a valid input data stream to within 250
ppm frequency error. This hysteresis is shown in Figure 20.
LOL
1
HARMONIC DETECTOR
0
250
1000
fVCO ERROR
(ppm)
04951-0-020
–250
–1000
Writing a 1 to I2C Register Bit CTRLB[7] causes the LOL pin,
Pin 16, to become a static LOL indicator. In this mode, the
LOL pin mirrors the contents of the MISC[4] bit and has
the functionality described in the previous paragraph. The
CTRLB[7] bit defaults to 0. In this mode, the LOL pin operates
in the normal operating mode, that is, it is asserted only when
the ADN2813 is in acquisition mode and deasserts when the
ADN2813 has reacquired lock.
Figure 20. Transfer Function of LOL
LOL Detector Operation Using a Reference Clock
In REFCLK mode, a reference clock is used as an acquisition aid
to lock the ADN2813 VCO. Lock-to-reference mode is enabled
by setting CTRLA[0] to 1. The user also needs to write to
the CTRLA[7:6] and CTRLA[5:2] bits to set the reference
frequency range and the divide ratio of the data rate with
respect to the reference frequency. For more details, see the
Reference Clock (Optional) section. In this mode, the lock
detector monitors the difference in frequency between the
divided down VCO and the divided down reference clock. The
loss-of-lock signal, which appears on Pin 16, LOL, is deasserted
when the VCO is within 250 ppm of the desired frequency. This
enables the D/PLL, which pulls the VCO frequency in the
remaining amount with respect to the input data and acquires
phase lock. Once locked, if the input frequency error exceeds
1000 ppm (0.1%), the loss-of-lock signal is reasserted and
control returns to the frequency loop, which reacquires with
respect to the reference clock. The LOL pin remains asserted
until the VCO frequency is within 250 ppm of the desired
frequency. This hysteresis is shown in Figure 20.
The ADN2813 provides a harmonic detector, which detects
whether or not the input data has changed to a lower harmonic
of the data rate that the VCO is currently locked onto. For
example, if the input data instantaneously changes from OC-12,
622.08 Mb/s to an OC-3, 155.52 Mb/s bit stream, this could be
perceived as a valid OC-12 bit stream, because the OC-3 data
pattern is exactly 4× slower than the OC-12 pattern. Therefore,
if the change in data rate is instantaneous, a 101 pattern at OC-3
would be perceived by the ADN2813 as a 111100001111 pattern
at OC-12. If the change to a lower harmonic is instantaneous, a
typical CDR could remain locked at the higher data rate.
The ADN2813 implements a harmonic detector that automatically identifies whether or not the input data has switched to a
lower harmonic of the data rate that the VCO is currently
locked onto. When a harmonic is identified, the LOL pin is
asserted and a new frequency acquisition is initiated. The
ADN2813 automatically locks onto the new data rate, and the
LOL pin is deasserted.
However, the harmonic detector does not detect higher
harmonics of the data rate. If the input data rate switches to a
higher harmonic of the data rate, then the VCO is currently
locked onto, the VCO loses lock, the LOL pin is asserted, and a
new frequency acquisition is initiated. The ADN2813
automatically locks onto the new data rate.
The time to detect lock to harmonic is
Static LOL Mode
The ADN2813 implements a static LOL feature, which indicates
if a loss-of-lock condition has ever occurred and remains
asserted, even if the ADN2813 regains lock, until the static LOL
bit is manually reset. The I2C register bit, MISC[4], is the static
LOL bit. If there is ever an occurrence of a loss-of-lock
condition, this bit is internally asserted to logic high. The
MISC[4] bit remains high even after the ADN2813 has
reacquired lock to a new data rate. This bit can be reset by
writing a 1 followed by 0 to I2C Register Bit CTRLB[6]. Once
reset, the MISC[4] bit remains deasserted until another loss-oflock condition occurs.
216 × (Td/ρ)
where:
1/Td is the new data rate. For example, if the data rate is
switched from OC-12 to OC-3, then Td = 1/155.52 MHz.
ρ is the data transition density. Most coding schemes seek to
ensure that ρ = 0.5, for example, PRBS, 8B/10B.
When the ADN2813 is placed in lock-to-reference mode, the
harmonic detector is disabled.
Rev. 0 | Page 17 of 28
ADN2813
SQUELCH MODE
Two SQUELCH modes are available with the ADN2813.
SQUELCH DATAOUT and CLKOUT mode is selected when
CTRLC[1] = 0 (default mode). In this mode, when the
SQUELCH input, Pin 27, is driven to a TTL high state, both
the clock and data outputs are set to the zero state to suppress
downstream processing. If the SQUELCH function is not
required, Pin 27 should be tied to VEE.
SQUELCH DATAOUT or CLKOUT mode is selected when
CTRLC[1] is 1. In this mode, when the SQUELCH input is
driven to a high state, the DATAOUTN/DATA OUTP pins are
squelched. When the SQUELCH input is driven to a low state,
the CLKOUT pins are squelched. This is especially useful in
repeater applications, where the recovered clock may not be
needed.
I2C INTERFACE
The ADN2813 supports a 2-wire, I2C-compatible serial bus
driving multiple peripherals. Two inputs, serial data (SDA) and
serial clock (SCK), carry information between any devices
connected to the bus. Each slave device is recognized by a
unique address. The ADN2813 has two possible 7-bit slave
addresses for both read and write operations. The MSB of the
7-bit slave address is factory programmed to 1. B5 of the slave
address is set by Pin 19, SADDR5. Slave Address Bits [4:0] are
defaulted to all 0s. The slave address consists of the 7 MSBs of
an 8-bit word. The LSB of the word either sets a read or write
operation (see Figure 7). Logic 1 corresponds to a read
operation, while Logic 0 corresponds to a write operation.
To control the device on the bus, the following protocol must be
followed. First, the master initiates a data transfer by establishing a start condition, defined by a high-to-low transition on
SDA while SCK remains high. This indicates that an address/
data stream follows. All peripherals respond to the start
condition and shift the next eight bits (the 7-bit address and
the R/W bit). The bits are transferred from MSB to LSB. The
peripheral that recognizes the transmitted address responds by
pulling the data line low during the ninth clock pulse. This is
known as an acknowledge bit. All other devices withdraw from
the bus at this point and maintain an idle condition. The idle
condition is where the device monitors the SDA and SCK lines
waiting for the start condition and correct transmitted address.
The R/W bit determines the direction of the data. Logic 0 on
the LSB of the first byte means that the master writes
information to the peripheral. Logic 1 on the LSB of the
first byte means that the master reads information from the
peripheral.
The ADN2813 acts as a standard slave device on the bus.
The data on the SDA pin is eight bits long, supporting the
7-bit addresses, plus the R/W bit. The ADN2813 has eight
subaddresses to enable the user-accessible internal registers
(see Table 6 through Table 10). It, therefore, interprets the first
byte as the device address and the second byte as the starting
subaddress. Auto-increment mode is supported, allowing data
to be read from or written to the starting subaddress and each
subsequent address without manually addressing the subsequent
subaddress. A data transfer is always terminated by a stop
condition. The user can also access any unique subaddress
register on a one-by-one basis without updating all registers.
Stop and start conditions can be detected at any stage of the
data transfer. If these conditions are asserted out of sequence
with normal read and write operations, they cause an immediate
jump to the idle condition. During a given SCK high period, the
user should issue one start condition, one stop condition, or a
single stop condition followed by a single start condition. If an
invalid subaddress is issued by the user, the ADN2813 does not
issue an acknowledge and returns to the idle condition. If the
user exceeds the highest subaddress while reading back in
auto-increment mode, then the highest subaddress register
contents continue to be output until the master device
issues a no acknowledge. This indicates the end of a read. In a
no acknowledge condition, the SDATA line is not pulled low
on the ninth pulse. See Figure 8 and Figure 9 for sample read
and write data transfers and Figure 10 for a more detailed
timing diagram.
REFERENCE CLOCK (OPTIONAL)
A reference clock is not required to perform clock and data
recovery with the ADN2813. However, support for an optional
reference clock is provided. The reference clock can be driven
differentially or single-ended. If the reference clock is not being
used, then REFCLKP should be tied to VCC, and REFCLKN
can be left floating or tied to VEE (the inputs are internally
terminated to VCC/2). See Figure 21 through Figure 23 for
sample configurations.
The REFCLK input buffer accepts any differential signal with a
peak-to-peak differential amplitude of greater than 100 mV (for
example, LVPECL or LVDS) or a standard single-ended, low
voltage TTL input, providing maximum system flexibility.
Phase noise and duty cycle of the reference clock are not
critical, and 100 ppm accuracy is sufficient.
Rev. 0 | Page 18 of 28
ADN2813
Using the Reference Clock to Lock onto Data
ADN2813
REFCLKP
In this mode, the ADN2813 locks onto a frequency derived
from the reference clock according to
10
BUFFER
Data Rate/2CTRLA[5:2] = REFCLK/2CTRLA[7:6]
11
100kΩ
100kΩ
VCC/2
04951-0-021
REFCLKN
The user must know exactly what the data rate is and provide a
reference clock that is a function of this rate. The ADN2813 can
still be used as a continuous rate device in this configuration,
provided that the user has the ability to provide a reference clock
that has a variable frequency (see Application Note AN-632).
Figure 21. Differential REFCLK Configuration
VCC
REFCLKP
CLK
OSC
ADN2813
The reference clock can be anywhere between 10 MHz and
160 MHz. By default, the ADN2813 expects a reference clock of
between 10 MHz and 20 MHz. If it is between 20 MHz and
40 MHz, 40 MHz and 80 MHz, or 80 MHz and 160 MHz, the
user needs to configure the ADN2813 to use the correct
reference frequency range by setting two bits of the CTRLA
register, CTRLA[7:6].
OUT
BUFFER
100kΩ
100kΩ
VCC/2
04951-0-022
REFCLKN
Figure 22. Single-Ended REFCLK Configuration
Table 11. CTRLA Settings
VCC
ADN2813
CTRLA[7:6]
00
01
10
11
10
REFCLKP
BUFFER
REFCLKN
100kΩ
100kΩ
VCC/2
04951-0-023
NC
11
Figure 23. No REFCLK Configuration
The two uses of the reference clock are mutually exclusive. The
reference clock can be used either as an acquisition aid for the
ADN2813 to lock onto data or to measure the frequency of the
incoming data to within 0.01%. (There is the capability to
measure the data rate to approximately ±10% without the use of
a reference clock.) The modes are mutually exclusive because, in
the first use, the user knows exactly what the data rate is and
wants to force the part to lock onto only that data rate; in the
second use, the user does not know what the data rate is and
wants to measure it.
Lock-to-reference mode is enabled by writing a 1 to I2C Register
Bit CTRLA[0]. Fine data rate readback mode is enabled by
writing a 1 to I2C Register Bit CTRLA[1]. Writing a 1 to both
of these bits at the same time causes an indeterminate state and
is not supported.
Range (MHz)
10 to 20
20 to 40
40 to 80
80 to 160
CTRLA[5:2]
0000
0001
n
1000
Ratio
1
2
2n
256
The user can specify a fixed integer multiple of the reference
clock to lock onto using CTRLA[5:2], where CTRLA should be
set to the data rate/DIV_FREF, where DIV_FREF represents the
divided-down reference referred to the 10 MHz to 20 MHz
band. For example, if the reference clock frequency is
38.88 MHz and the input data rate is 622.08 Mb/s, CTRLA[7:6]
is set to [01] to give a divided-down reference clock of
19.44 MHz. CTRLA[5:2] is set to [0101], that is, 5, because
622.08 Mb/s/19.44 MHz = 25
In this mode, if the ADN2813 loses lock for any reason, it relocks
onto the reference clock and continues to output a stable clock.
While the ADN2813 is operating in lock-to-reference mode, if
the user ever changes the reference frequency, the FREF range
(CTRLA[7:6]) or the FREF ratio (CTRLA[5:2]), this must be
followed by writing a 0 to 1 transition into the CTRLA[0] bit to
initiate a new lock-to-reference command.
Using the Reference Clock to Measure Data Frequency
The user can also provide a reference clock to measure the
recovered data frequency. In this case, the user provides a
reference clock, and the ADN2813 compares the frequency of
the incoming data to the incoming reference clock and returns a
ratio of the two frequencies to 0.01% (100 ppm). The accuracy
error of the reference clock is added to the accuracy of the
ADN2813 data rate measurement. For example, if a 100 ppm
accuracy reference clock is used, the total accuracy of the
measurement is within 200 ppm.
Rev. 0 | Page 19 of 28
ADN2813
The reference clock can range from 10 MHz and 160 MHz.
The ADN2813 expects a reference clock between 10 MHz
and 20 MHz by default. If it is between 20 MHz and 40 MHz,
40 MHz and 80 MHz, or 80 MHz and 160 MHz, the user needs
to configure the ADN2813 to use the correct reference
frequency range by setting two bits of the CTRLA register,
CTRLA[7:6]. Using the reference clock to determine the
frequency of the incoming data does not affect the manner in
which the part locks onto data. In this mode, the reference clock
is used only to determine the frequency of the data. For this
reason, the user does not need to know the data rate to use the
reference clock in this manner.
Prior to reading back the data rate using the reference clock, the
CTRLA[7:6] bits must be set to the appropriate frequency range
with respect to the reference clock being used. A fine data rate
readback is then executed as follows:
1. Write a 1 to CTRLA[1]. This enables the fine data rate
measurement capability of the ADN2813. This bit is level
sensitive and does not need to be reset to perform
subsequent frequency measurements.
2. Reset MISC[2] by writing a 1 followed by a 0 to CTRLB[3].
This initiates a new data rate measurement.
3. Read back MISC[2]. If it is 0, the measurement is not
complete. If it is 1, the measurement is complete and the
data rate can be read back on FREQ[22:0]. The time for a
data rate measurement is typically 80 ms.
4. Read back the data rate from FREQ2[6:0], FREQ1[7:0],
and FREQ0[7:0].
The data rate can be determined by
f DATARATE = (FREQ [22..0] × f REFCLK )/ 2(14 +SEL _ RATE)
For example, if the reference clock frequency is 32 MHz,
SEL_RATE = 1, since the CTRLA[7:6] setting is [01], because
the reference frequency falls into the 20 MHz to 40 MHz range.
Assume for this example that the input data rate is 1.25 Gb/s
(GbE). After following Step 1 through Step 4, the value that is
read back on FREQ[22:0] = 0x138800, which is equal to
1.28 × 106. Plugging this value into the equation yields
128e6 × 32e6/2(14 + 1) = 1.25 Gb/s
If subsequent frequency measurements are required, CTRLA[1]
should remain set to 1. It does not need to be reset. The
measurement process is reset by writing a 1 followed by a 0 to
CTRLB[3]. This initiates a new data rate measurement. Follow
Step 2 through Step 4 to read back the new data rate.
Note that a data rate readback is valid only if LOL is low. If LOL
is high, the data rate readback is invalid.
Additional Features Available via the I2C Interface
Coarse Data Rate Readback
The data rate can be read back over the I2C interface to
approximately ±10% without the need of an external reference
clock. A 9-bit register, COARSE_RD[8:0], can be read back
when LOL is deasserted. The eight MSBs of this register are the
contents of the RATE[7:0] register. The LSB of the
COARSE_RD register is Bit MISC[0].
Table 13 provides coarse data rate readback to within ±10%.
LOS Configuration
The LOS detector output, Pin 22, can be configured to be either
active high or active low. If CTRLC[2] is set to Logic 0 (default),
the LOS pin is active high when a loss-of-signal condition is
detected. Writing a 1 to CTRLC[2] configures the LOS pin to be
active low when a loss-of-signal condition is detected.
System Reset
where:
FREQ[22:0] is the reading from FREQ2[6:0] MSByte,
FREQ1[7:0], and FREQ0[7:0] LSByte (see Table 12).
fDATARATE is the data rate (Mb/s).
A frequency acquisition can be initiated by writing a 1 followed
by a 0 to the I2C Register Bit CTRLB[5]. This initiates a new
frequency acquisition while keeping the ADN2813 in the
operating mode that it was previously programmed to in
Registers CTRL[A], CTRL[B], and CTRL[C].
fREFCLK is the REFCLK frequency (MHz).
SEL_RATE is the setting from CTRLA[7:6].
Table 12.
D22
D21...D17
FREQ2[6:0]
D16
D15
D14...D9
FREQ1[7:0]
Rev. 0 | Page 20 of 28
D8
D7
D6...D1
FREQ0[7:0]
D0
ADN2813
APPLICATIONS INFORMATION
PCB DESIGN GUIDELINES
Proper RF PCB design techniques must be used for optimal
performance.
If connections to the supply and ground are made through
vias, the use of multiple vias in parallel helps to reduce series
inductance, especially on Pin 24, which supplies power to the
high speed CLKOUTP/CLKOUTN and DATAOUTP/
DATAOUTN output buffers. Refer to Figure 24 for the
recommended connections.
Power Supply Connections and Ground Planes
Use of one low impedance ground plane is recommended. The
VEE pins should be soldered directly to the ground plane to
reduce series inductance. If the ground plane is an internal
plane and connections to the ground plane are made through
vias, multiple vias can be used in parallel to reduce the series
inductance, especially on Pin 23, which is the ground return for
the output buffers. The exposed pad should be connected to the
GND plane using plugged vias so that solder does not leak
through the vias during reflow.
By using adjacent power supply and GND planes, excellent high
frequency decoupling can be realized by using close spacing
between the planes. This capacitance is given by
C PLANE = 0.88ε r A/d (pF)
where:
εr is the dielectric constant of the PCB material.
Use of a 22 μF electrolytic capacitor between VCC and VEE is
recommended at the location where the 3.3 V supply enters the
PCB. When using 0.1 μF and 1 nF ceramic chip capacitors, they
should be placed between the IC power supply VCC and VEE,
as close as possible to the ADN2813 VCC pins.
A is the area of the overlap of power and GND planes (cm2).
d is the separation between planes (mm).
For FR-4, εr = 4.4 mm and 0.25 mm spacing, C ~15 pF/cm2.
50Ω TRANSMISSION LINES
VCC
DATAOUTP
+
22μF
0.1μF
DATAOUTN
1nF
CLKOUTP
TEST2
VCC
VEE
DATAOUTP
DATAOUTN
SQUELCH
CLKOUTP
CLKOUTN
CLKOUTN
TIA
32
31
30
29
28
27
26
25
50Ω
CIN
50Ω
1nF
VCC
VEE
LOS
SDA
SCK
SADDR5
VCC
VEE
1nF
0.1μF
I2C CONTROLLER
I2C CONTROLLER
μC
VCC
0.1μF
μC
RTH
0.47μF ±20%
>300MΩ INSULATION RESISTANCE
VCC
0.1μF
1nF
Figure 24. Typical ADN2813 Applications Circuit
Rev. 0 | Page 21 of 28
04951-0-031
0.1μF
VCC
24
EXPOSED PAD 23
TIED OFF TO 22
VEE PLANE 21
20
WITH VIAS
19
18
17
9
10
11
12
13
14
15
16
1nF
1
2
3
4
5
6
7
8
THRADJ
REFCLKP
REFCLKN
NC
VCC
VEE
CF2
CF1
LOL
0.1μF
TEST1
VCC
VREF
NIN
PIN
SLICEP
SLICEN
VEE
VCC
ADN2813
Transmission Lines
Choosing AC Coupling Capacitors
Use of 50 Ω transmission lines is required for all high frequency
input and output signals to minimize reflections: PIN, NIN,
CLKOUTP, CLKOUTN, DATAOUTP, and DATAOUTN (also
REFCLKP and REFCLKN, if a high frequency reference clock is
used, such as 155 MHz). It is also necessary for the PIN/NIN
input traces to be matched in length, and the CLKOUTP/
CLKOUTN and DATAOUTP/DATAOUTN output traces to be
matched in length to avoid skew between the differential traces.
AC coupling capacitors at the input (PIN, NIN) and output
(DATAOUTP, DATAOUTN) of the ADN2813 must be chosen
such that the device works properly over the full range of data
rates used in the application. When choosing the capacitors, the
time constant formed with the two 50 Ω resistors in the signal
path must be considered. When a large number of consecutive
identical digits (CIDs) are applied, the capacitor voltage can
droop due to baseline wander (see Figure 26), causing patterndependent jitter (PDJ).
The high speed inputs, PIN and NIN, are internally terminated
with 50 Ω to an internal reference voltage (see Figure 25).
A 0.1 μF is recommended between VREF, Pin 3, and GND to
provide an ac ground for the inputs.
As with any high speed, mixed-signal design, take care to keep
all high speed digital traces away from sensitive analog nodes.
The user must determine how much droop is tolerable and
choose an ac coupling capacitor based on that amount of droop.
The amount of PDJ can then be approximated based on the
capacitor selection. The actual capacitor value selection can
require some trade-offs between droop and PDJ.
For example, assuming 2% droop can be tolerated, then the
maximum differential droop is 4%. Normalizing to V p-p:
VCC
ADN2813
50Ω
CIN
Droop = Δ V = 0.04 V = 0.5 V p-p (1 − e–t/τ); therefore, τ = 12t
PIN
where:
TIA
CIN
τ is the RC time constant (C is the ac coupling capacitor,
R = 100 Ω seen by C).
NIN
50Ω
50Ω
2.5V
0.1μF
VREF
3kΩ
t is the total discharge time, which is equal to nT.
04951-0-026
50Ω
Figure 25. ADN2813 AC-Coupled Input Configuration
Soldering Guidelines for Lead Frame Chip Scale Package
The lands on the 32-lead LFCSP are rectangular. The printed
circuit board (PCB) pad for these should be 0.1 mm longer than
the package land length and 0.05 mm wider than the package
land width. The land should be centered on the pad. This
ensures that the solder joint size is maximized. The bottom of
the chip scale package has a central exposed pad. The pad on
the PCB should be at least as large as this exposed pad. The user
must connect the exposed pad to VEE using plugged vias so
that solder does not leak through the vias during reflow. This
ensures a solid connection from the exposed pad to VEE.
n is the number of CIDs.
T is the bit period.
The capacitor value can then be calculated by combining the
equations for τ and t:
C = 12nT/R
Once the capacitor value is selected, the PDJ can be
approximated as
PDJpspp = 0.5tr(1 − e(−nT/RC))/0.6
where:
PDJpspp is the amount of pattern-dependent jitter allowed;
< 0.01 UI p-p typical.
tr is the rise time, which is equal to 0.22/BW, where BW ~ 0.7
(bit rate).
Note that this expression for tr is accurate only for the inputs.
The output rise time for the ADN2813 is ~100 ps regardless of
data rate.
Rev. 0 | Page 22 of 28
ADN2813
VCC
V1
ADN2813
CIN
V2
PIN
COUT
+
DATAOUTP
50Ω
TIA
V1b CIN V2b
CDR
LIMAMP
VREF
DATAOUTN
50Ω
COUT
–
NIN
V1
1
2
3
4
V1b
V2
VREF
V2b
VTH
VDIFF
NOTES:
1. DURING DATA PATTERNS WITH HIGH TRANSITION DENSITY, DIFFERENTIAL DC VOLTAGE AT V1 AND V2 IS ZERO.
2. WHEN THE OUTPUT OF THE TIA GOES TO CID, V1 AND V1b ARE DRIVEN TO DIFFERENT DC LEVELS. V2 AND V2b DISCHARGE TO THE
VREF LEVEL, WHICH EFFECTIVELY INTRODUCES A DIFFERENTIAL DC OFFSET ACROSS THE AC COUPLING CAPACITORS.
3. WHEN THE BURST OF DATA STARTS AGAIN, THE DIFFERENTIAL DC OFFSET ACROSS THE AC COUPLING CAPACITORS IS APPLIED TO
THE INPUT LEVELS CAUSING A DC SHIFT IN THE DIFFERENTIAL INPUT. THIS SHIFT IS LARGE ENOUGH SUCH THAT ONE OF THE STATES,
EITHER HIGH OR LOW DEPENDING ON THE LEVELS OF V1 AND V1b WHEN THE TIA WENT TO CID, IS CANCELED OUT. THE QUANTIZER
DOES NOT RECOGNIZE THIS AS A VALID STATE.
4. THE DC OFFSET SLOWLY DISCHARGES UNTIL THE DIFFERENTIAL INPUT VOLTAGE EXCEEDS THE SENSITIVITY OF THE ADN2813. THE
QUANTIZER CAN RECOGNIZE BOTH HIGH AND LOW STATES AT THIS POINT.
04951-0-027
VDIFF = V2–V2b
VTH = ADN2813 QUANTIZER THRESHOLD
Figure 26. Example of Baseline Wander
PIN
V p-p = PIN – NIN = 2 × VSE = 10mV AT SENSITIVITY
VSE = 5mV MIN
NIN
VCM = 2.3V MIN
(DC-COUPLED)
04951-0-029
The inputs to the ADN2813 can also be dc-coupled. This may
be necessary in burst mode applications, where there are long
periods of CIDs, and baseline wander cannot be tolerated. If the
inputs to the ADN2813 are dc-coupled, care must be taken not
to violate the input range and common-mode level requirements of the ADN2813 (see Figure 27 through Figure 29). If dc
coupling is required, and the output levels of the TIA do not
adhere to the levels shown in Figure 28, then level shifting
and/or an attenuator must be between the TIA outputs and the
ADN2813 inputs.
INPUT (V)
DC-COUPLED APPLICATION
Figure 28. Minimum Allowed DC-Coupled Input Levels
VCC
V p-p = PIN – NIN = 2 × VSE = 2.0V MAX
ADN2813
50Ω
PIN
50Ω
NIN
PIN
VSE = 1.0V MAX
50Ω
0.1μF
VREF
NIN
04951-0-030
2.5V
3kΩ
VCM = 2.3V
(DC-COUPLED)
04951-0-028
50Ω
INPUT (V)
TIA
Figure 27. DC-Coupled Application
Figure 29. Maximum Allowed DC-Coupled Input Levels
Rev. 0 | Page 23 of 28
ADN2813
COARSE DATA RATE READBACK LOOK-UP TABLE
Code is the 9-bit value read back from COARSE_RD[8:0].
Table 13. Look-Up Table
Code
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
FMID
5.3745e+06
5.3741e+06
5.4793e+06
5.5912e+06
5.7111e+06
5.8391e+06
5.9760e+06
6.1215e+06
6.2780e+06
6.4565e+06
6.6391e+06
6.8372e+06
7.0520e+06
7.2868e+06
7.5424e+06
7.8220e+06
7.6663e+06
7.6659e+06
7.8217e+06
7.9880e+06
8.1667e+06
8.3570e+06
8.5616e+06
8.7805e+06
9.0166e+06
9.2849e+06
9.5608e+06
9.8591e+06
1.0183e+07
1.0535e+07
1.0918e+07
1.1332e+07
1.0749e+07
1.0748e+07
1.0959e+07
1.1182e+07
1.1422e+07
1.1678e+07
1.1952e+07
1.2243e+07
1.2556e+07
1.2913e+07
1.3278e+07
1.3674e+07
1.4104e+07
1.4574e+07
1.5085e+07
1.5644e+07
Code
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
FMID
1.5333e+07
1.5332e+07
1.5643e+07
1.5976e+07
1.6333e+07
1.6714e+07
1.7123e+07
1.7561e+07
1.8033e+07
1.8570e+07
1.9122e+07
1.9718e+07
2.0367e+07
2.1070e+07
2.1835e+07
2.2664e+07
2.1498e+07
2.1496e+07
2.1917e+07
2.2365e+07
2.2844e+07
2.3357e+07
2.3904e+07
2.4486e+07
2.5112e+07
2.5826e+07
2.6556e+07
2.7349e+07
2.8208e+07
2.9147e+07
3.0170e+07
3.1288e+07
3.0665e+07
3.0664e+07
3.1287e+07
3.1952e+07
3.2667e+07
3.3428e+07
3.4246e+07
3.5122e+07
3.6066e+07
3.7140e+07
3.8243e+07
3.9436e+07
4.0733e+07
4.2140e+07
4.3671e+07
4.5328e+07
Code
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
Rev. 0 | Page 24 of 28
FMID
4.2996e+07
4.2993e+07
4.3834e+07
4.4729e+07
4.5688e+07
4.6713e+07
4.7808e+07
4.8972e+07
5.0224e+07
5.1652e+07
5.3113e+07
5.4698e+07
5.6416e+07
5.8295e+07
6.0339e+07
6.2576e+07
6.1331e+07
6.1328e+07
6.2574e+07
6.3904e+07
6.5334e+07
6.6856e+07
6.8493e+07
7.0244e+07
7.2133e+07
7.4279e+07
7.6486e+07
7.8872e+07
8.1467e+07
8.4279e+07
8.7341e+07
9.0657e+07
8.5991e+07
8.5986e+07
8.7668e+07
8.9458e+07
9.1377e+07
9.3426e+07
9.5616e+07
9.7944e+07
1.0045e+08
1.0330e+08
1.0623e+08
1.0940e+08
1.1283e+08
1.1659e+08
1.2068e+08
1.2515e+08
Code
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
FMID
1.2266e+08
1.2266e+08
1.2515e+08
1.2781e+08
1.3067e+08
1.3371e+08
1.3699e+08
1.4049e+08
1.4427e+08
1.4856e+08
1.5297e+08
1.5774e+08
1.6293e+08
1.6856e+08
1.7468e+08
1.8131e+08
1.7198e+08
1.7197e+08
1.7534e+08
1.7892e+08
1.8275e+08
1.8685e+08
1.9123e+08
1.9589e+08
2.0089e+08
2.0661e+08
2.1245e+08
2.1879e+08
2.2566e+08
2.3318e+08
2.4136e+08
2.5030e+08
2.4532e+08
2.4531e+08
2.5029e+08
2.5562e+08
2.6134e+08
2.6742e+08
2.7397e+08
2.8098e+08
2.8853e+08
2.9712e+08
3.0594e+08
3.1549e+08
3.2587e+08
3.3712e+08
3.4936e+08
3.6263e+08
ADN2813
Code
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
FMID
3.4397e+08
3.4394e+08
3.5067e+08
3.5783e+08
3.6551e+08
3.7370e+08
3.8247e+08
3.9177e+08
4.0179e+08
4.1322e+08
4.2490e+08
4.3758e+08
4.5133e+08
4.6636e+08
4.8272e+08
5.0061e+08
Code
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
FMID
4.9064e+08
4.9062e+08
5.0059e+08
5.1123e+08
5.2267e+08
5.3485e+08
5.4794e+08
5.6195e+08
5.7706e+08
5.9423e+08
6.1189e+08
6.3098e+08
6.5173e+08
6.7423e+08
6.9873e+08
7.2525e+08
Code
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
Rev. 0 | Page 25 of 28
FMID
6.8793e+08
6.8789e+08
7.0135e+08
7.1567e+08
7.3102e+08
7.4741e+08
7.6493e+08
7.8355e+08
8.0358e+08
8.2643e+08
8.4981e+08
8.7516e+08
9.0266e+08
9.3272e+08
9.6543e+08
1.0012e+09
Code
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
FMID
9.8129e+08
9.8124e+08
1.0012e+09
1.0225e+09
1.0453e+09
1.0697e+09
1.0959e+09
1.1239e+09
1.1541e+09
1.1885e+09
1.2238e+09
1.2620e+09
1.3035e+09
1.3485e+09
1.3975e+09
1.4505e+09
ADN2813
OUTLINE DIMENSIONS
0.60 MAX
5.00
BSC SQ
0.60 MAX
25
24
PIN 1
INDICATOR
TOP
VIEW
0.50
BSC
4.75
BSC SQ
0.50
0.40
0.30
12° MAX
1.00
0.85
0.80
PIN 1
INDICATOR
32
1
EXPOSED
PAD
(BOTTOM VIEW)
17
16
3.45
3.30 SQ
3.15
9
8
0.25 MIN
3.50 REF
0.80 MAX
0.65 TYP
0.05 MAX
0.02 NOM
SEATING
PLANE
0.30
0.23
0.18
0.20 REF
COPLANARITY
0.08
COMPLIANT TO JEDEC STANDARDS MO-220-VHHD-2
Figure 30. 32-Lead Frame Chip Scale Package [LFCSP_VQ]
5 mm × 5 mm Body, Very Thin Quad
(CP-32-3)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADN2813ACPZ 1
ADN2813ACPZ-500RL71
ADN2813ACPZ-RL71
EVAL-ADN2813EB
1
Temperature Range
−40°C to 85°C
−40°C to 85°C
−40°C to 85°C
Package Description
32-Lead LFCSP_VQ
32-Lead LFCSP_VQ, Tape-Reel, 500 Pieces
32-Lead LFCSP_VQ, Tape-Reel, 1,500 Pieces
Evaluation Board
Z = Pb-free part.
Rev. 0 | Page 26 of 28
Package Option
CP-32-3
CP-32-3
CP-32-3
ADN2813
NOTES
Rev. 0 | Page 27 of 28
ADN2813
NOTES
Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I2C
Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
© 2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D04951–0–9/05(0)
T
T
Rev. 0 | Page 28 of 28