AD AD9954YSV

400 MSPS, 14-Bit, 1.8 V CMOS,
Direct Digital Synthesizer
AD9954
FEATURES
GENERAL DESCRIPTION
400 MSPS internal clock speed
Integrated 14-bit DAC
Programmable phase/amplitude dithering
32-bit frequency tuning accuracy
14-bit phase tuning accuracy
Phase noise better than –120 dBc/Hz
Excellent dynamic performance
>80 dB narrowband SFDR
Serial I/O control
Ultrahigh speed analog comparator
Automatic linear and nonlinear frequency sweeping
4 frequency/phase offset profiles
1.8 V power supply
Software and hardware controlled power-down
48-lead TQFP
Integrated 1024 word × 32-bit RAM
Support for 5 V input levels on most digital inputs
PLL-based REFCLK multiplier
Internal oscillator, can be driven by a single crystal
Phase modulation capability
Multichip synchronization
The AD9954 is a direct digital synthesizer (DDS) that uses
advanced technology, coupled with an internal high speed, high
performance DAC to form a complete, digitally programmable,
high frequency synthesizer capable of generating a frequencyagile analog output sinusoidal waveform at up to 160 MHz.
The AD9954 enables fast frequency hopping coupled with fine
tuning of both frequency (0.01 Hz or better) and phase (0.022°
granularity).
The AD9954 is programmed via a high speed serial I/O port.
The device includes static RAM to support flexible frequency
sweep capability in several modes, plus a user-defined linear
sweep mode of operation. Also included is an on-chip high
speed comparator for applications requiring a square wave
output. An on-chip oscillator and PLL circuitry provide users
with multiple approaches to generate the device’s system clock.
The AD9954 is specified to operate over the extended industrial
temperature range (see Table 2).
APPLICATIONS
Agile LO frequency synthesis
Programmable clock generators
FM chirp source for radar and scanning systems
Automotive radars
Test and measurement equipment
Acousto-optic device drivers
BASIC BLOCK DIAGRAM
AD9954
400MSPS
DDS CORE
DIGITAL
SINE
WAVE
14-BIT
DAC
COMPARATOR
TIMING AND
CONTROL
USER INTERFACE
03374-038
REF CLOCK
INPUT CIRCUITRY
Figure 1.
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2003–2009 Analog Devices, Inc. All rights reserved.
AD9954
TABLE OF CONTENTS
Features .............................................................................................. 1
Serial Interface Port Pin Descriptions ..................................... 24
Applications ....................................................................................... 1
MSB/LSB Transfers .................................................................... 24
General Description ......................................................................... 1
RAM I/O via Serial Port ............................................................ 24
Basic Block Diagram ........................................................................ 1
Instruction Byte .......................................................................... 25
Revision History ............................................................................... 2
Register Maps and Descriptions ............................................... 25
Functional Block Diagram .............................................................. 3
Control Register Bit Descriptions ............................................ 29
Electrical Specifications ................................................................... 4
Other Register Descriptions ..................................................... 31
Absolute Maximum Ratings............................................................ 7
Layout Considerations ............................................................... 32
Explanation of Test Levels ........................................................... 7
Detailed Programming Examples ................................................ 33
ESD Caution .................................................................................. 7
Single-Tone Mode ...................................................................... 33
Pin Configuration and Function Descriptions ............................. 8
Linear Sweep Mode .................................................................... 33
Typical Performance Characteristics ........................................... 10
RAM Mode.................................................................................. 33
Theory of Operation ...................................................................... 13
Suggested Application Circuits ..................................................... 35
Component Blocks ..................................................................... 13
Evaluation Board Schematics........................................................ 36
Modes of Operation ................................................................... 16
Outline Dimensions ....................................................................... 39
Synchronization—Register Updates (I/O UPDATE) ............ 21
Ordering Guide .......................................................................... 39
Serial Port Operation ................................................................. 23
REVISION HISTORY
5/09—Rev. A to Rev. B
Changes to Figure 29 and Figure 30 ............................................. 24
Changes to Table 12 ........................................................................ 26
Changes to Figure 34 ...................................................................... 35
Updated Outline Dimensions ....................................................... 39
Changes to Ordering Guide .......................................................... 39
1/07—Rev. 0 to Rev. A
Changes to Layout .............................................................. Universal
Changes to Features, General Description, and Figure 1 ............ 1
Changes to Figure 2 .......................................................................... 3
Changes to Table 1 ............................................................................ 4
Changes to Table 4 ............................................................................ 8
Changes to Figure 5 to Figure 10 .................................................. 10
Changes to Figure 12 ...................................................................... 11
Changes to Figure 17 to Figure 18 Captions ............................... 12
Deleted Figure 19; Renumbered Sequentially ............................ 12
Added Table 5; Renumbered Sequentially .................................. 13
Changes to Component Block Section and Table 6 ................... 13
Changes to Figure 20 ...................................................................... 15
Changes to Modes of Operation Section and Table 8................ 16
Changes to Table 9 .......................................................................... 17
Changes to Synchronization; Register Updates (I/O UPDATE)
Section and Figure 24 ..................................................................... 21
Changes to Serial Port Operation Section................................... 23
Changes to Serial Interface Port Pin Description Section,
MSB/LSB Transfers Section, and RAM I/O Via Serial Port
Section.............................................................................................. 24
Inserted Figure 29 and Figure 30; Renumbered Sequentially .. 24
Changes to Instruction Byte Section, Register Maps and
Descriptions Section, and Table 12 .............................................. 25
Changes to Table 13 ....................................................................... 26
Changes to Table 14 ....................................................................... 28
Added Single-Tone Mode Section, Linear Sweep Mode Section,
Table 15, and RAM Mode Section ............................................... 33
Added, and Table 16 ....................................................................... 34
Inserted Figure 35 ........................................................................... 36
Inserted Figure 36 ........................................................................... 37
Inserted Figure 37 ........................................................................... 38
Updated Outline Dimensions ....................................................... 39
Changes to Ordering Guide .......................................................... 39
10/03—Revision 0: Initial Version
Rev. B | Page 2 of 40
AD9954
FUNCTIONAL BLOCK DIAGRAM
DDS CORE
M
U
X
FREQUENCY
TUNING WORD
32
DDS
CLOCK
10
14
COS(X)
14
DAC
SYSTEM
CLOCK
MUX
SYNC_IN
θ
OSK
TIMING AND CONTROL LOGIC
M
U
X
PWRDWNCTL
0
SYNC
CONTROL REGISTERS
÷4
COMPARATOR
OSCILLATOR/BUFFER
4× TO 20×
CLOCK
MULTIPLIER
REFCLK
REFCLK
M
U
X
COMP_IN
COMP_IN
SYSTEM
CLOCK
COMP_OUT
ENABLE
CRYSTAL OUT
IOUT
IOUT
Z–1
RAM DATA 14
<31:18>
I/O UPDATE
SYNC_CLK
19
14
3
32
32
CLEAR
PHASE
ACCUMULATOR
32
DAC_R SET
PHASE
OFFSET
Z–1
32
DDS CLOCK
RAM CONTROL
RAM DATA
RAM
DATA
AD9954
PHASE
ACCUMULATOR
PS<1:0>
I/O PORT
Figure 2.
Rev. B | Page 3 of 40
RESET
03374-001
32
STATIC RAM
1024 × 32
RAM ADDRESS
DELTA FREQUENCY TUNING WORD
DELTA FREQUENCY RAMP RATE
FREQUENCY
ACCUMULATOR
AD9954
ELECTRICAL SPECIFICATIONS
Unless otherwise noted, AVDD, DVDD = 1.8 V ± 5%, DVDD_I/O = 3.3 V ± 5%, RSET = 3.92 kΩ, external reference clock frequency =
400 MHz. DAC output must be referenced to AVDD, not AGND.
Table 1.
Parameter
REF CLOCK INPUT CHARACTERISTICS
Frequency Range
REFCLK Multiplier Disabled
REFCLK Multiplier Enabled at 4×
REFCLK Multiplier Enabled at 20×
Crystal Oscillator Operating Frequency
Input Capacitance
Input Impedance
Duty Cycle
Duty Cycle with REFCLK Multiplier Enabled
REFCLK Input Voltage Swing
DAC OUTPUT CHARACTERISTICS
Full-Scale Output Current
Gain Error
Output Offset
Differential Nonlinearity
Integral Nonlinearity
Output Capacitance
Residual Phase Noise @ 1 kHz Offset, 40 MHz AOUT
REFCLK Multiplier Enabled @ 20×
REFCLK Multiplier Enabled @ 4×
REFCLK Multiplier Disabled
Voltage Compliance Range
Wideband SFDR
1 MHz to 10 MHz Analog Out
10 MHz to 40 MHz Analog Out
40 MHz to 80 MHz Analog Out
80 MHz to 120 MHz Analog Out
120 MHz to 160 MHz Analog Out
Narrow-Band SFDR
40 MHz Analog Out (±1 MHz)
40 MHz Analog Out (±250 kHz)
40 MHz Analog Out (±50 kHz)
40 MHz Analog Out (±10 kHz)
80 MHz Analog Out (±1 MHz)
80 MHz Analog Out (±250 kHz)
80 MHz Analog Out (±50 kHz)
80 MHz Analog Out (±10 kHz)
120 MHz Analog Out (±1 MHz)
120 MHz Analog Out (±250 kHz)
120 MHz Analog Out (±50 kHz)
120 MHz Analog Out (±10 kHz)
160 MHz Analog Out (±1 MHz)
160 MHz Analog Out (±250 kHz)
160 MHz Analog Out (±50 kHz)
160 MHz Analog Out (±10 kHz)
Temp
Test
Level
Full
Full
Full
Full
25°C
25°C
25°C
25°C
Full
VI
VI
VI
IV
V
V
V
V
IV
25°C
25°C
25°C
25°C
25°C
25°C
I
I
V
V
V
25°C
25°C
25°C
25°C
V
V
V
I
25°C
25°C
25°C
25°C
25°C
V
V
V
V
V
73
67
62
58
52
dBc
dBc
dBc
dBc
dBc
25°C
25°C
25°C
25°C
25°C
25°C
25°C
25°C
25°C
25°C
25°C
25°C
25°C
25°C
25°C
25°C
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
87
89
91
93
85
87
89
91
83
85
87
89
81
83
85
87
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
Rev. B | Page 4 of 40
Min
Typ
1
20
4
20
Max
Unit
400
100
20
30
MHz
MHz
MHz
MHz
pF
kΩ
%
%
mV p-p
3
1.5
50
35
100
5
–10
65
1000
10
15
+10
0.6
1
2
5
–105
–115
–132
AVDD – 0.5
AVDD + 0.5
mA
%FS
μA
LSB
LSB
pF
dBc/Hz
dBc/Hz
dBc/Hz
V
AD9954
Temp
Test
Level
25°C
25°C
25°C
25°C
V
IV
I
IV
Full
Full
25°C
25°C
25°C
25°C
25°C
VI
VI
IV
IV
IV
IV
IV
25°C
25°C
25°C
25°C
V
V
V
V
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
IV
IV
IV
IV
IV
IV
IV
IV
IV
IV
Full
Full
Full
I
I
I
4
6
0
25°C
IV
24
I/O UPDATE to Phase Offset Change Prop Delay
25°C
IV
24
I/O UPDATE to Amplitude Change Prop Delay
25°C
IV
16
PS0, PS1 to RAM Driven Frequency Change Prop Delay
25°C
IV
28
PS0, PS1 to RAM Driven Phase Change Prop Delay
25°C
IV
28
PS0 to Linear Frequency Sweep Prop Delay
25°C
IV
28
Parameter
COMPARATOR INPUT CHARACTERISTICS
Input Capacitance
Input Resistance
Input Current
Hysteresis
COMPARATOR OUTPUT CHARACTERISTICS
Logic 1 Voltage, High-Z Load
Logic 0 Voltage, High-Z Load
Propagation Delay
Output Duty-Cycle Error
Rise/Fall Time, 5 pF Load
Toggle Rate, High-Z Load
Output Jitter1
COMPARATOR NARROW-BAND SFDR
10 MHz to 160 MHz FOUT
Measured over a 1 MHz BW
Measured over a 250 kHz BW
Measured over a 50 kHz BW
Measured over a 10 Hz BW
TIMING CHARACTERISTICS
Serial Control Bus
Maximum Frequency
Minimum Clock Pulse Width Low
Minimum Clock Pulse Width High
Maximum Clock Rise/Fall Time
Minimum Data Setup Time DVDD_I/O = 3.3 V
Minimum Data Setup Time DVDD_I/O = 1.8 V
Minimum Data Hold Time
Maximum Data Valid Time
Wake-Up Time2
Minimum Reset Pulse Width High
I/O UPDATE, PS0, PS1 to SYNC_CLK Setup Time, DVDD_I/O = 3.3 V
I/O UPDATE, PS0, PS1 to SYNC_CLK Setup Time, DVDD_I/O = 1.8 V
I/O UPDATE, PS0, PS1 to SYNC_CLK Hold Time
Latency
I/O UPDATE to Frequency Change Prop Delay
Rev. B | Page 5 of 40
Min
Typ
Max
Unit
45
pF
kΩ
μA
mV
3
500
±12
30
1.6
0.4
3
±5
1
200
1
80
85
90
95
dBc
dBc
dBc
dBc
25
Mbps
ns
ns
ns
ns
ns
ns
ns
ms
SYSCLK
cycles3
ns
ns
ns
7
7
2
3
5
0
25
1
5
V
V
ns
%
ns
MHz
ps rms
SYSCLK
cycles
SYSCLK
cycles
SYSCLK
cycles
SYSCLK
cycles
SYSCLK
cycles
SYSCLK
cycles
AD9954
Parameter
CMOS LOGIC INPUTS
Logic 1 Voltage @ DVDD_I/O (Pin 43) = 1.8 V
Logic 0 Voltage @ DVDD_I/O (Pin 43) = 1.8 V
Logic 1 Voltage @ DVDD_I/O (Pin 43) = 3.3 V
Logic 0 Voltage @ DVDD_I/O (Pin 43) = 3.3 V
Logic 1 Current
Logic 0 Current
Input Capacitance
CMOS LOGIC OUTPUTS (1 mA Load) DVDD_I/O = 1.8 V
Logic 1 Voltage
Logic 0 Voltage
CMOS LOGIC OUTPUTS (1 mA Load) DVDD_I/O = 3.3 V
Logic 1 Voltage
Logic 0 Voltage
POWER CONSUMPTION (AVDD = DVDD = 1.8 V)
Single-Tone Mode (Comparator Off )
With RAM or Linear Sweep Enabled
With Comparator Enabled
With RAM and Comparator Enabled
Rapid Power-Down Mode
Full-Sleep Mode
SYNCHRONIZATION FUNCTION4
Maximum Sync Clock Rate (DVDD_I/O = 1.8 V)
Maximum Sync Clock Rate (DVDD_I/O = 3.3 V)
SYNC_CLK Alignment Resolution5
Temp
Test
Level
25°C
25°C
25°C
25°C
25°C
25°C
25°C
I
I
I
I
V
V
V
1.25
25°C
25°C
I
I
1.35
25°C
25°C
I
I
2.8
25°C
25°C
25°C
25°C
25°C
25°C
I
I
I
I
I
I
25°C
25°C
25°C
VI
VI
V
1
Min
Typ
Max
0.6
2.2
3
0.8
12
12
2
162
175
180
198
150
20
62.5
100
±1
Unit
V
V
V
V
μA
μA
pF
0.4
V
V
0.4
V
V
171
190
190
220
160
27
mW
mW
mW
mW
mW
mW
MHz
MHz
SYSCLK
cycles
Represents the cycle-to-cycle residual jitter from the comparator alone.
Wake-up time refers to the recovery from analog power-down modes (see section on Power-Down Modes of Operation). The primary limiting factor is the settling time of the PLL
multiplier in the reference circuitry. The wake-up time assumes there is no capacitor on DAC BP and that the recommended PLL loop filter values are used.
3
SYSCLK cycle refers to the clock frequency used on-chip to drive the DDS core. This is equal to the frequency of the reference source times the value of the PLL-based
reference clock multiplier.
4
SYNC_CLK = ¼ SYSCLK rate. Be sure the high speed sync enable bit, CFR2<11>, is programmed appropriately.
5
This parameter indicates that the digital synchronization feature cannot compensate for phase delays (timing skew) between system clock rising edges. If the system
clock edges are aligned, the synchronization function should not increase the skew between the two edges.
2
Rev. B | Page 6 of 40
AD9954
ABSOLUTE MAXIMUM RATINGS
EXPLANATION OF TEST LEVELS
Table 2.
Parameter
Maximum Junction Temperature
DVDD_I/O (Pin 43)
AVDD, DVDD
Digital Input Voltage (DVDD_I/O = 3.3 V)
Digital Input Voltage (DVDD_I/O = 1.8 V)
Digital Output Current
Storage Temperature Range
Operating Temperature Range
Lead Temperature (10 sec Soldering)
θJA
θJC
I
II
Rating
150°C
4V
2V
–0.7 V to +5.25 V
–0.7 V to +2.2 V
5 mA
–65°C to +150°C
–40°C to +105°C
300°C
38°C/W
15°C/W
III
IV
V
VI
100% production tested.
100% production tested at 25°C and sample tested at
specified temperatures.
Sample tested only.
Parameter is guaranteed by design and characterization
testing.
Parameter is a typical value only.
Devices are 100% production tested at 25°C and
guaranteed by design and characterization testing
for industrial operating temperature range.
ESD CAUTION
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
DVDD_I/O
IOUT
IOUT
INPUT
AVOID OVERDRIVING
DIGITAL INPUTS.
FORWARD BIASING
ESD DIODES MAY
COUPLE DIGITAL NOISE
ONTO POWER PINS.
COMPARATOR
INPUTS
COMPARATOR
OUTPUT
AVDD
COMP IN
COMP IN
MUST TERMINATE
OUTPUTS TO AVDD FOR
CURRENT FLOW. DO
NOT EXCEED THE
OUTPUT VOLTAGE
COMPLIANCE RATING.
Figure 3. Equivalent Input and Output Circuits
Rev. B | Page 7 of 40
03374-032
DIGITAL
OUTPUTS
DIGITAL
INPUTS
AD9954
IOSYNC
SDO
CS
SCLK
SDIO
DGND
DVDD_I/O
SYNC_IN
SYNC_CLK
OSK
PS0
PS1
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
48 47 46 45 44 43 42 41 40 39 38 37
I/O UPDATE 1
DVDD
2
DGND
3
36
PIN 1
RESET
35
PWRDWNCTL
34
DVDD
33
DGND
32
AGND
31
COMP_IN
30
COMP_IN
8
29
AVDD
9
28
COMP_OUT
CRYSTAL OUT 10
27
AVDD
AVDD
4
AGND
5
AVDD
6
AGND
7
OSC/REFCLK
OSC/REFCLK
AD9954
TOP VIEW
(Not to Scale)
26 AGND
CLKMODESELECT 11
LOOP_FILTER 12
25 AVDD
03374-002
DAC_R SET
DACBP
AGND
IOUT
IOUT
AVDD
AVDD
AGND
AVDD
AGND
AVDD
AGND
13 14 15 16 17 18 19 20 21 22 23 24
Figure 4. Pin Configuration
Note that the exposed paddle on the bottom of the package forms an electrical connection for the DAC and must be attached to
analog ground. Note that Pin 43, DVDD_I/O, can be powered to 1.8 V or 3.3 V. The DVDD pins (Pin 2 and Pin 34) must be
powered to 1.8 V.
Table 3. Pin Function Descriptions
Pin No.
1
Mnemonic
I/O UPDATE
I/O
I
2, 34
3, 33, 42
4, 6, 13, 16,
18, 19, 25,
27, 29
5, 7, 14, 15,
17, 22, 26,
32
8
DVDD
DGND
AVDD
I
I
I
Description
The rising edge transfers the contents of the internal buffer memory to the I/O registers.
See Synchronization—Register Updates (I/O UPDATE) section for details.
Digital Power Supply Pins (1.8 V).
Digital Power Ground Pins.
Analog Power Supply Pins (1.8 V).
AGND
I
Analog Power Ground Pins.
OSC/REFCLK
I
9
10
11
OSC/REFCLK
CRYSTAL OUT
CLKMODESELECT
I
O
I
12
LOOP_FILTER
I
20
21
23
24
IOUT
IOUT
DACBP
DAC_RSET
O
O
I
I
28
30
COMP_OUT
COMP_IN
O
I
Oscillator Input/Complementary Reference Clock. When the REFCLK port is operated in
single-ended mode, REFCLK should be decoupled to AVDD with a 0.1 μF capacitor.
Oscillator Input/Reference Clock. See Table 5 for details on the OSC/REFCLK operation.
Output of the Oscillator Section.
Control Pin for the Oscillator Section (1.8 V logic only). See REFCLK Input section for detailed
instructions.
This pin provides the connection for the external zero compensation network of the REFCLK
multiplier’s PLL loop filter. The network varies based on the multiplication value in the PLL loop.
See Table 4 for details.
Complementary DAC Output. Should be biased through a resistor to AVDD, not AGND.
DAC Output. Should be biased through a resistor to AVDD, not AGND.
DAC Band Gap Decoupling Pin. A 0.1 μF capacitor to AGND is recommended.
A resistor (3.92 kΩ nominal) connected from AGND to DAC_RSET establishes the reference
current for the DAC. See equation in DAC Output section.
Comparator Output.
Comparator Input.
Rev. B | Page 8 of 40
AD9954
Pin No.
31
35
36
Mnemonic
COMP_IN
PWRDWNCTL
RESET
I/O
I
I
I
37
IOSYNC
I
38
39
40
41
43
44
SDO
CS
SCLK
SDIO
DVDD_I/O
SYNC_IN
O
I
I
I/O
I
I
45
46
SYNC_CLK
OSK
O
I
47, 48
PS0, PS1
I
<49>
AGND
I
Description
Comparator Complementary Input.
Input Pin Used as an External Power-Down Control (see Table 9 for details).
Active High Hardware Reset Pin. Assertion of the RESET pin forces the AD9954 to the default
state, as described in the right-hand column of Table 12, which is the I/O port register map.
Asynchronous Active High Reset of the Serial Port Controller. When high, the current I/O
operation is immediately terminated, enabling a new I/O operation to commence once
IOSYNC is returned low. If unused, ground this pin; do not allow this pin to float.
See Serial Interface Port Pin Description section for details.
See Serial Interface Port Pin Description section for details.
See Serial Interface Port Pin Description section for details.
See Serial Interface Port Pin Description section for details.
Digital Power Supply. This pin is for I/O cells only, 3.3 V.
Input Signal Used to Synchronize Multiple AD9954s. This input is connected to the SYNC_CLK
output of a master AD9954.
Clock Output Pin that Serves as a Synchronizer for External Hardware.
Input Pin Used to Control the Direction of the Shaped On-Off Keying Function When Programmed
for Operation. OSK is synchronous to the SYNC_CLK pin. When OSK is disabled, this pin should
be tied to DGND.
Input Pins Used to Select One of the Internal Phase/Frequency Profiles. PS1 and PS0 are
synchronous to the SYNC_CLK pin. Change on these pins triggers a transfer of the contents of
the chosen internal buffer memory to the I/O registers (sends an internal I/O UPDATE).
The Exposed Paddle on the Bottom of the Package. It is a ground connection for the DAC and
must be attached to AGND in any board layout.
Rev. B | Page 9 of 40
AD9954
TYPICAL PERFORMANCE CHARACTERISTICS
MKR1 101MHz
–70.68dB
ATTEN 10dB
REF 0dBm
0
PEAK
LOG
10dB/ –10
–20
–20
–30
–30
MARKER
101MHz
–70.68dB
–50
–40
–60
W1 S2
S3 FC –70
AA
–80
03374-016
1
–90
–100
CENTER 100MHz
#RES BW 3kHz
VBW 3kHz
–90
SPAN 200MHz
SWEEP 55.56 s (401 PTS)
CENTER 100MHz
#RES BW 3kHz
REF 0dBm
0
PEAK
LOG
10dB/ –10
–20
–20
–30
–30
MARKER
90MHz
–69.12dB
–40
–50
–40
03374-017
–90
–100
VBW 3kHz
ATTEN 10dB
CENTER 100MHz
#RES BW 3kHz
VBW 3kHz
SPAN 200MHz
SWEEP 55.56 s (401 PTS)
Figure 9 fOUT = 120 MHz, fCLK = 400 MSPS, WBSFDR
MKR1 80MHz
–68.44dB
REF 0dBm
0
PEAK
LOG
10dB/ –10
1R
ATTEN 10dB
MKR1 80MHz
–53.17dB
1R
–20
–30
–50
1
–90
SPAN 200MHz
SWEEP 55.56 s (401 PTS)
–20
–40
1R
–100
Figure 6. fOUT = 10 MHz, fCLK = 400 MSPS, WBSFDR
REF 0dBm
0
PEAK
LOG
10dB/ –10
MKR1 160MHz
–56.2dB
ATTEN 10dB
–60
W1 S2
S3 FC –70
AA
–80
1
CENTER 100MHz
#RES BW 3kHz
SPAN 200MHz
SWEEP 55.56 s (401 PTS)
MARKER
160MHz
–56.2dB
–50
–60
W1 S2
S3 FC –70
AA
–80
VBW 3kHz
Figure 8. fOUT = 80 MHz, fCLK = 400 MSPS, WBSFDR
MKR1 90MHz
–69.12dB
ATTEN 10dB
1
–100
Figure 5. fOUT = 1 MHz, fCLK = 400 MSPS, WBSFDR
REF 0dBm
0
PEAK
1R
LOG
10dB/ –10
MARKER
160MHz
–61.55dB
–50
–60
W1 S2
S3 FC –70
AA
–80
1R
03374-019
–40
MKR1 160MHz
–61.55dB
ATTEN 10dB
03374-020
REF 0dBm
0
PEAK
1R
LOG
10dB/ –10
–30
MARKER
80MHz
–68.44dB
–40
–50
MARKER
80MHz
–53.17dB
1
–60
–60
W1 S2
S3 FC –70
AA
–80
03374-018
1
–90
–100
CENTER 100MHz
#RES BW 3kHz
VBW 3kHz
SPAN 200MHz
SWEEP 55.56 s (401 PTS)
Figure 7. fOUT = 40 MHz, fCLK = 400 MSPS, WBSFDR
03374-021
W1 S2
S3 FC –70
AA
–80
–90
–100
CENTER 100MHz
#RES BW 3kHz
VBW 3kHz
SPAN 200MHz
SWEEP 55.56 s (401 PTS)
Figure 10. fOUT = 160 MHz, fCLK = 400 MSPS, WBSFDR
Rev. B | Page 10 of 40
AD9954
REF –4dBm
0
PEAK
LOG
10dB/ –10
ATTEN 10dB
1
MKR1 1.105MHz
–5.679dBm
REF –4dBm
0
PEAK
LOG
10dB/ –10
–20
–20
–30
–30
–40
–40
MARKER
1.105000MHz
–5.679dBm
–50
–50
CENTER 1.105MHz
#RES BW 30Hz
VBW 30Hz
SPAN 2MHz
SWEEP 199.2 s (401 PTS)
REF 0dBm
0
PEAK
LOG
10dB/ –10
CENTER 80.25MHz
#RES BW 30Hz
Figure 14. fOUT = 80.3 MHz, fCLK = 400 MSPS, NBSFDR, ±1 MHz
MKR1 10MHz
–93.01dB
ATTEN 10dB
–90
ST
–100
SPAN 2MHz
SWEEP 199.2 s (401 PTS)
Figure 11. fOUT = 1.1 MHz, fCLK = 400 MSPS, NBSFDR, ±1 MHz
REF –4dBm
0
PEAK
LOG
10dB/ –10
1R
–20
–20
–30
–30
–40
–40
MARKER
10MHz
–93.01dB
–50
–50
ATTEN 10dB
1
MKR1 120.205MHz
–6.825dBm
MARKER
120.205000MHz
–6.825dBm
–60
W1 S2
S3 FC –70
AA
–80
–90
03374-023
W1 S2
S3 FC –70
AA
–80
1
–100
CENTER 10MHz
#RES BW 30Hz
VBW 30Hz
ATTEN 10dB
1
–90
ST
–100
SPAN 2MHz
SWEEP 199.2 s (401 PTS)
CENTER 120.2MHz
#RES BW 30Hz
Figure 12. fOUT = 9.5 MHz, fCLK = 400 MSPS, NBSFDR, ±1 MHz
REF 0dBm
0
PEAK
LOG
10dB/ –10
03374-026
–60
VBW 30Hz
SPAN 2MHz
SWEEP 199.2 s (401 PTS)
Figure 15. fOUT = 120.2 MHz, fCLK = 400 MSPS, NBSFDR, ±1 MHz
MKR1 39.905MHz
–5.347dBm
REF –4dBm
0
PEAK
LOG
10dB/ –10
–20
ATTEN 10dB
1
MKR1 600kHz
–0.911dB
–20
–30
–30
–40
MARKER
39.905000MHz
–5.347dBm
CENTER
160.5000000MHz
–50
–60
W1 S2
S3 FC –70
AA
–80
03374-024
–60
W1 S2
S3 FC –70
AA
–80
–90
–100
CENTER 39.9MHz
#RES BW 30Hz
VBW 30Hz
SPAN 2MHz
SWEEP 199.2 s (401 PTS)
Figure 13. fOUT = 39.9 MHz, fCLK = 400 MSPS, NBSFDR, ±1 MHz
03374-027
–50
VBW 30Hz
MARKER
80.301000MHz
–6.318dBm
03374-025
–90
ST
–100
–40
MKR1 80.301MHz
–6.318dBm
–60
W1 S2
S3 FC –70
AA
–80
03374-022
–60
W1 S2
S3 FC –70
AA
–80
1
ATTEN 10dB
–90
ST
–100
CENTER 160.5MHz
#RES BW 30Hz
VBW 30Hz
SPAN 2MHz
SWEEP 199.2 s (401 PTS)
Figure 16. fOUT = 160 MHz, fCLK = 400 MSPS, NBSFDR, ±1 MHz
Rev. B | Page 11 of 40
AD9954
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
R1
R2
100
1k
10k
f (Hz)
100k
1M
10M
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
03374-029
L(f) (dBc/Hz)
0
–10
100
1k
10k
100k
REF2 200mV 500ns
M 500PS 20.0GS/S IT 10.0PS/PT –100PS
A CH1
708mV
Figure 19. Comparator Rise and Fall Time at 160 MHz
Figure 17. Residual Phase Noise with fOUT = 159.5 MHz,
fCLK = 400 MSPS; PLL Bypassed (Green), PLL Set to 4× (Red), and
PLL Set to 20× (Blue)
–120
–130
–140
–150
–160
–170
10
03374-030
–120
–130
–140
–150
–160
–170
10
FALL (R1) = 396.4PS
RISE(R2) = 464.3PS
03374-028
L(f) (dBc/Hz)
0
–10
1M
f (Hz)
Figure 18. Residual Phase Noise with fOUT = 9.5 MHz, fCLK = 400 MSPS;
PLL Bypassed (Green), PLL Set to 4× (Red), and PLL Set to 20× (Blue)
Rev. B | Page 12 of 40
AD9954
THEORY OF OPERATION
COMPONENT BLOCKS
REFCLK Input
The AD9954 supports several methods for generating the
internal system clock. An on-chip oscillator circuit is available
for initiating the low frequency reference signal by connecting a
crystal to the clock input pins. The system clock can be generated
using an internal, PLL-based reference clock multiplier, allowing
the part to operate with a low frequency clock source while still
providing a high sample rate for the DDS and DAC. For best
phase noise performance, a clean, stable clock with a high slew
rate should be used to drive the REFCLK pin and bypass the
multiplier.
The available modes are configured using the CLKMODESELECT
pin, CFR1<4> and CFR2<7:3>. Note that the CLKMODESELECT
pin is a 1.8 V logic only and does not apply to 3.3 V logic.
Pulling CLKMODESELECT high enables the on-chip crystal
oscillator circuit. With the on-chip oscillator enabled, users of
the AD9954 connect an external crystal to the REFCLK and
REFCLK inputs to produce a low frequency reference clock (see
Table 1 for the crystal frequency range supported). The signal
generated by the oscillator is buffered, and then delivered to the
rest of the chip. This buffered signal is provided on the
CRYSTAL OUT pin.
When the internal oscillator is disabled, an external oscillator
must provide the REFCLK and/or REFCLK signals. For differential
operation, these pins are driven with complementary signals. For
single-ended operation, a 0.1 μF capacitor should be connected
between the unused pin and the analog power supply. With the
capacitor in place, the clock input pin bias voltage is 1.35 V.
Table 5 summarizes the clock modes of operation. Note the PLL
multiplier is controlled via the CFR2<7:3> bits, independent of
the CFR1<4> bit.
Clock Multiplier
An on-board PLL allows multiplication of the REFCLK
frequency. The multiplication factor is set using CFR2<7:3>.
When programmed for values ranging from 0x04 to 0x14
(decimal 4 to 20), the PLL multiplies the REFCLK input
frequency by the programmed value. The user must consider the
specified maximum frequency for the PLL when programming. If
the multiplication factor is changed, the user must allocate time
to allow the PLL to lock (approximately 1 ms).
The PLL is bypassed by programming a value outside the range
of 4 to 20 (decimal). When bypassed, the PLL is shut down to
conserve power.
The VCO in the PLL has a selectable frequency range. Use the
VCO range bit (CFR2<2>) to set the appropriate range.
The PLL in the clock multiplier has a loop filter comprised
of on-chip components as well as external components.
Recommended values for the external resistor/capacitor
are provided in Table 4.
Table 4. External Loop Filter Components for Clock Multiplier
Multiply Value
4×
10×
20×
Resistor Value
0Ω
1 kΩ
243 Ω
Capacitor Value (μF)
0.1
0.1
0.01
DAC Output
Unlike many DACs, the DAC output on the AD9954 is referenced
to AVDD, not AGND.
Two complementary outputs provide a combined full-scale
output current (IOUT). Differential outputs reduce the amount of
common-mode noise that may be present at the DAC output,
resulting in a better signal-to-noise ratio. The full-scale current
is controlled by means of an external resistor (RSET) connected
between the DAC_RSET pin and the DAC ground pin (Pin 49,
the exposed paddle). The full-scale current is proportional to
the resistor value by the equation
RSET  39.19/I OUT  Ω
The maximum full-scale output current of the combined
DAC outputs is 15 mA. Limiting the output to 10 mA
maximum provides the best spurious-free dynamic range
(SFDR) performance. The DAC output compliance range is
AVDD + 0.5 V to AVDD − 0.5 V. Voltages developed beyond
this range result in excessive DAC distortion and could potentially
damage the DAC output circuitry. Proper attention should be
paid to the load termination to keep the output voltage within
this compliance range.
Table 5. Clock Input Modes of Operation
CFR1<4>
Low
Low
Low
Low
High
CLKMODESELECT
High
High
Low
Low
X
CFR2<7:3>
4 ≤ M ≤ 20
M < 4 or M > 20
4 ≤ M ≤ 20
M < 4 or M > 20
X
Oscillator Enabled?
Yes
Yes
No
No
No
Rev. B | Page 13 of 40
System Clock
fCLK = fOSC × M
fCLK = fOSC
fCLK = fOSC × M
fCLK = fOSC
fCLK = 0
Frequency Range (MHz)
80 < fCLK < 400
20 < fCLK < 30
80 < fCLK < 400
10 < fCLK < 400
N/A
AD9954
Comparator
Frequency Tuning Word Mux
Some applications (for example, clocking) prefer a square-wave
signal rather than a sine wave. In support of such applications,
the AD9954 includes an on-chip comparator. The comparator
has a bandwidth greater than 200 MHz and a common-mode
input range of 1.3 V to 1.8 V. The comparator can be turned off
to reduce power consumption using the comparator powerdown bit, CFR1<6>.
As shown in Figure 2, there are three sources for the FTW
that are fed to the DDS core as the seed value for the phase
accumulator: a frequency accumulator, the static RAM, and
the registers of the control logic.
Frequency Accumulator
This block is used for linear sweep mode; transitioning from
the start frequency (F0) to the terminal frequency (F1) is not
instantaneous but instead is implemented in a swept or ramped
fashion. This frequency ramping is accomplished by stepping
through intermediate frequencies between F0 and F1.
The linear sweep block uses the falling and rising delta
frequency tuning words, the falling and rising delta frequency
ramp rates, and the frequency accumulator. The Linear Sweep
Enable Bit CFR1<21> enables the linear sweep block. The linear
sweep no dwell bit establishes the action to be performed upon
reaching the terminal frequency in a sweep. See the Modes of
Operation section for more details.
DDS Core
The output frequency (fO) of the DDS is a function of the
frequency of system clock (SYSCLK), the value of the frequency
tuning word (FTW), and the capacity of the phase accumulator
(232, in this case). The exact relationship is given below with fs
defined as the frequency of SYSCLK.
fO = (FTW)(fS)/232 with 0 ≤ FTW ≤ 231
fO = fS × (1 − (FTW/232)) with 231 < FTW < 232 − 1
Each system clock cycle, the FTW is added to the value
previously held in the phase accumulator. The value at the
output of the phase accumulator is then summed with a userdefined, 14-bit phase offset value (POW). The most significant
19 bits of that summation are then translated to an amplitude
value via the cos(x) functional block. Truncation of the LSBs is
implemented to reduce the power consumption of the DDS
core. This truncation does not reduce frequency resolution.
In certain applications, it is desirable to have the ability to force
the output signal to zero phase. Simply setting the FTW to 0
does not accomplish this; it only stalls the core at its current
phase value. A control bit is provided to force the phase
accumulator output to zero.
At power-up, the clear phase accumulator bit is set to Logic 1,
but the buffer memory for this bit is cleared (Logic 0). Therefore,
upon power-up, the phase accumulator remains clear until the
first I/O UPDATE is issued. I/O UPDATE transfers data from
the input buffers to the active control registers. See the
Functionality of the SYNC_CLK and I/O UPDATE section
for more details.
For applications where a static output frequency or more than
four predefined output frequencies need to be switched between,
in some variable or undefined order, the primary method of
setting the FTW is by programming the desired value into the
FTW0 register.
For applications where up to four specific sets of FTWs, or predefined series of FTWs are needed, the on-board RAM can be
programmed with the desired FTWs, and the profile pins can
be used to toggle between those sets/series.
For applications where a steady sweeping of frequency is
desired, a second frequency accumulator is provided. The seed
value and minimum/maximum numbers for the frequency
accumulator are user programmable, although certain rules
must be followed to avoid overflowing that accumulator.
Phase Offset Word Mux
As shown in Figure 2, there are two sources for the POW that
are fed to the DDS core as an adder to the output of the phase
accumulator: the static RAM and the registers of the control
logic. Using this feature enables synchronization of the DDS
output to other system signals as well as phase modulation.
For applications where a static output phase or more than four
predefined output phases need to be switched between, in some
variable or undefined order, the primary method of setting the
POW is by programming the desired value into the POW0
register.
For applications where up to four specific sets of POWs, or
predefined series of POWs are needed, the on-board RAM can
be programmed with the desired POWs, and the profile pins
can be used to toggle between those sets/series.
The phase offset formula is
POW
   14   360
 2 
A digital delay block exists in the phase offset programming
path to ensure matched latency with changes to the frequency
tuning word. This enables users to easily program the device to
change from one combined phase/frequency combination to
another smoothly and seamlessly.
Continuous and Clear-and-Release Frequency and Phase
Accumulator Clear Functions
The AD9954 allows for a continuous zeroing of the frequency
sweep logic and the phase accumulator as well as a clear and
release or automatic zeroing function. The auto clear bits are
CFR1<14:13>. The continuous clear bits are CFR1<11:10>.
Rev. B | Page 14 of 40
AD9954
Clear-and-Release Function
When set for auto clearing, the corresponding accumulator is
cleared and then begins to accumulate again upon receipt of an
I/O update or change on one of the profile pins. This is repeated
for every subsequent I/O update or change on one of the profile
pins until the appropriate autoclear control bit is cleared. It is
perfectly valid to have one accumulator set to autoclearing and
the other set to continuous clear.
Amplitude Control Options
Shaped On-Off Keying
The shaped on-off keying function is enabled/disabled using
the OSK enable bit (CFR1<25>). This function allows the
user to control the ramp-up and ramp-down time when turning
the DAC on or off. This function is primarily used in burst
transmissions of digital data to reduce the adverse spectral
impact of short, abrupt bursts of data.
Both auto and manual shaped on-off keying modes are
supported. CFR1<24> is used to select between auto and
manual on-off keying modes. Figure 20 shows the block
diagram of the OSK circuitry.
Note that the maximum amplitude allowed is limited by the
contents of the amplitude scale factor register, allowing the user
to ramp to a value less than full scale.
Table 6. Autoscale Factor Internal Step Size
ASF<15:14> (Binary)
00
01
10
11
Increment/Decrement Size
1
2
4
8
OSK Ramp Rate Timer
The OSK ramp rate timer is a loadable down counter, which
generates the clock signal to the 14-bit counter that generates
the internal scale factor. The ramp rate timer is loaded with
the value of the autoscale factor register (ASFR) every time
the counter reaches 1 (decimal). This load and countdown
operation continues for as long as the timer is enabled, unless
the timer is forced to load before reaching a count of 1.
If the load ARR control bit (CFR1<26>) is set, the ramp rate
timer is loaded upon an I/O update, upon a change in profile
input, or upon reaching a value of 1. The ramp timer can be
loaded before reaching a count of 1 by three methods.
Autoshaped On-Off Keying Mode Operation
When autoshaped on-off keying mode is enabled, a single-scale
factor is internally generated and applied to the multiplier input
for scaling the output of the DDS core block (see Figure 20). The
scale factor is the output of a 14-bit counter that increments/
decrements at a rate determined by the contents of the 8-bit
output ramp rate register. The scale factor increments if the
OSK pin is high and decrements if the OSK pin is low. The scale
factor is an unsigned value; all 0s multiply the DDS core output
by 0 (decimal), and 0x3FFF multiplies the DDS core output by
16,383 (decimal).
The first method is by toggling the OSK pin or sending a rising
edge to the I/O UPDATE pin (or changing the state of a profile
pin). For this method, the ASFR value is loaded into the ramp
rate timer, which then proceeds to count down as normal.
The second method is if the load ARR control bit (CFR1<26>)
is set and an I/O update (or change in profile) is issued.
The last method is by setting the sweep enable bit. This switches
from inactive autoshaped on-off keying mode to the active
autoshaped on-off keying mode.
Table 6 details the increment/decrement step size of the
internally generated scale factor per the ASF<15:14> bits.
DDS CORE
0
TO DAC
1
COS(X)
AUTO OSK
ENABLE
CFR1<24>
OSK ENABLE
CFR<25>
SYNC_CLK
1
OSK PIN
AMPLITUDE RAMP
RATE REGISTER
(ASF)
0
0
1
AMPLITUDE SCALE
FACTOR REGISTER
(ASF)
OUT
LOAD OSK TIMER
CFR1<26>
HOLD
UP/DN
LOAD
INC/DEC ENABLE
DATA
EN
CLOCK
AUTOSCALE
FACTOR GENERATOR
RAMP RATE TIMER
Figure 20. On-Off Shaped Keying, Block Diagram
Rev. B | Page 15 of 40
03374-005
0
AD9954
In single-tone mode, the DDS core uses a static tuning word.
Whatever value is stored in FTW0 is supplied to the phase
accumulator. This value can only be changed manually by
writing a new value to FTW0 and then by issuing an I/O update.
Phase adjustments are made using the phase offset register.
To perform 4-tone shift keying, the user programs each RAM
segment control word for direct switch mode and a unique
beginning address value. Program the RAM enable and RAM
destination bits (CFR1<31:30>) to enable the RAM and direct
the RAM output to be the FTW (FSK) or the POW (PSK). The
PS1 and PS0 inputs are the 4-tone FSK/PSK data inputs. When
the profile is changed, the data stored at the new profile is
loaded into either the phase accumulator (FSK) or the phase
offset adder (PSK). When set for PSK, Bits<17:0> of the RAM
output are unused when the RAM destination bit is set. Twotone shift keying only uses one profile pin.
RAM-Controlled Modes of Operation
Ramp-Up Mode
Three important points apply to the RAM-controlled modes:
Ramp-up mode, in conjunction with the segmented RAM
capability, allows up to four different sweep profiles to be
programmed into the AD9954. The AD9954 is programmed
for ramp-up mode by enabling the RAM using the RAM enable
bit (CFR1<31>) and programming the RAM mode control bits
of each profile to be used to 001(b).
Manual Shaped On-Off Keying Mode Operation
When configured for manual shaped on-off keying, the
content of the ASFR sets the scale factor for the data path.
MODES OF OPERATION
Single-Tone Mode
 The user must ensure that the beginning address is lower
than the final address.
 Changing profiles or issuing an I/O update automatically
terminates the current sweep and starts the next sweep, unless
otherwise stated.
 Setting the RAM destination bit true such that the RAM
output drives the phase offset adder is valid. While the
sections that follow describe frequency sweeps, phase
sweep operation is also available. The RAM destination bit
(CFR1<30>) controls whether the RAM output drives the
phase accumulator (frequency) or the phase offset adder
(phase).
The AD9954 offers five modes of RAM-controlled operation
(see Table 7).
Table 7. RAM Modes of Operation
RSCW<7:5> (Binary)
000
Mode
Direct Switch
001
Ramp Up
010
Bidirectional
Ramp
011
100
101, 110, 111
Continuous
Bidirectional
Ramp
Continuous
Recirculation
Invalid mode
Notes
No sweeping, profiles
valid, no dwell ignored
Sweeping, profiles valid,
no-dwell valid
Sweeping, PS0 is a
direction control pin,
no-dwell ignored
Sweeping, profiles valid,
no-dwell ignored
Sweeping, profiles valid,
no-dwell ignored
Default to direct switch
Direct Switch Mode
Direct switch mode enables frequency shift keying (FSK) or
phase shift keying (PSK) modulation. The AD9954 is
programmed for direct switch using the RAM enable bit
(CFR1<31>) and programming the RAM segment mode
control bits of each desired profile to 000(b). This mode simply
reads the RAM contents at the RAM segment beginning
address for the current profile. No address ramping occurs in
this mode.
When a sweep is initiated (via an I/O update or change in
profile bits), the RAM address generator loads the RAM
segment beginning address bits of the current RSCW, driving
the RAM output from this address, and the ramp rate timer
loads the RAM segment address ramp rate bits. When the ramp
rate timer finishes a cycle, the RAM address generator increments
to the next address, the timer reloads the ramp rate bits and
begins a new countdown cycle. This sequence continues until
the RAM address generator has incremented to an address
equal to the RAM segment final address bits of the current
RSCW. At this point, the next state is dependent upon whether
no-dwell mode is active. See the no-dwell bit (CFR1<2>) in the
register maps (see Table 12 and Table 13).
In this mode, asymmetrical FSK modulation can be implemented
by configuring the RAM for two segments, and using the PS0
pin as the data input.
Bidirectional Ramp Mode
Bidirectional ramp mode allows the AD9954 to offer a
symmetrical sweep between two frequencies using the PS0
signal as the control input. The AD9954 is programmed for
bidirectional ramp mode using the RAM enable bit (CFR1<31>)
and programming the RAM segment mode control bits of each
desired profile to 010(b). PS1 input is ignored; the PS0 input is
the ramp direction indicator. The memory is not segmented,
using only one beginning and one final address. The address
registers for controlling RAM are located in the RAM segment
control word (RSCW) associated with Profile 0.
Rev. B | Page 16 of 40
AD9954
Upon entering this mode (via an I/O update or changing the
PS0 pin), the RAM address generator loads the RAM segment
beginning address bits of RSCW0 and the ramp rate timer loads
the RAM segment address ramp rate bits. The RAM drives data
from the beginning address, and the ramp rate timer begins
counting down to 1. When the timer reaches zero, the RAM
address is incremented if PS0 is high and decrements if PS0 is
low. Toggling the PS0 pin does not cause the device to generate
an internal I/O update; transfers of data from the I/O buffers to
the internal registers are only initiated by a rising edge on the
I/O UPDATE pin.
RAM address control is now a function of the PS0 input. When
polarity of the PS0 bit is changed, the RAM address generator
increments/decrements to the next address and the ramp rate
timer is reloaded. As in the ramp-up mode, this sequence
continues until the RAM address generator has incremented/
decremented to an address equal to the final/beginning address
as long as the PS0 input remains high/low. Once the final/
beginning address is reached, the sweep stalls until the polarity
on PS0 is changed.
All data in the RAM segment control words associated with
Profile 1, Profile 2, and Profile 3 are ignored. Only the information
in the RAM segment control word for Profile 0 is used to
control the RAM.
Continuous Bidirectional Ramp Mode
Continuous bidirectional ramp mode allows the AD9954
to offer an automatic, symmetrical sweep between two
frequencies. The AD9954 is programmed for continuous
bidirectional ramp mode using the RAM enable bit (CFR1<31>)
and programming the RAM segment mode control bits of each
desired profile to 011(b). In general, this mode is identical in
control to the bidirectional ramp mode, except the ramp up and
down is automatic (no external control via the PS0 input), and
switching profiles are valid. This mode enables generation of an
automatic saw tooth sweep characteristic.
Upon entering this mode (via an I/O update or changing the
PS1 or PS0 pins), the RAM address generator loads the RAM
segment beginning address bits of the current RSCW and the
ramp rate timer loads the RAM segment address ramp rate bits.
The RAM drives data from the beginning address, and the ramp
rate timer begins counting down to 1. When the ramp rate timer
completes the countdown, the RAM address generator increments
to the next address, and the timer reloads the ramp rate bits and
continues counting down. This continues until the RAM address
generator has incremented to an address equal to the RAM
segment final address bits of the current RSCW. Upon reaching
this final address, the RAM address generator begins
decrementing each time the ramp rate timer completes a
countdown cycle until it reaches the RAM segment beginning
address. Upon reaching the beginning address, the entire
sequence repeats until a new mode is selected.
Continuous Recirculation Mode
Continuous recirculation mode allows the AD9954 to offer
an automatic, continuous unidirectional sweep between two
frequencies. The AD9954 is programmed for continuous
recirculation mode using the RAM enable bit (CFR1<31>)
and programming the RAM segment mode control bits of
each desired profile to 100(b).
Upon entering this mode (via an I/O update or changing Pin
PS1 or Pin PS0), the RAM address generator loads the RAM
segment beginning address bits of the current RSCW and the
ramp rate timer loads the RAM segment address ramp rate bits.
The RAM drives data from the beginning address, and the ramp
rate timer begins to count down to 1. When the ramp rate timer
completes a cycle, the RAM address generator increments to the
next address, and the timer reloads the ramp rate bits and
continues counting down. This sequence continues until the
RAM address generator has incremented to an address equal to
the RAM segment final address bits of the current RSCW. Upon
reaching this terminal address, the RAM address generator
reloads the RAM segment beginning address bits and the
sequence repeats until a new mode is selected.
Internal Profile Control
The AD9954 offers a mode in which a composite frequency sweep
can be built with software-programmable timing control. Internal
profile control capability disengages the PS1 pin and the PS0 pin
and enables the AD9954 to take control of switching between
profiles. Modes are defined that allow continuous or single-burst
profile switches for three combinations of profile selection bits
(see Table 8). Internal profile control mode is engaged using Bits
CFR1<29:27> per Table 8. Internal profile control is only valid
when the device is operating in RAM mode. There is no internal
profile control for linear sweeping operations.
When the internal profile control mode is engaged, the RAM
segment mode control bits are ignored; the device operates all
profiles in ramp-up mode. Switching between profiles occurs
when the RAM address generator has exhausted the memory
contents for the current profile.
Rev. B | Page 17 of 40
AD9954
Table 8. Internal Profile Control
CFR1<29:27>
(Binary)
000
001
010
011
100
101
110
111
Mode Description
Internal control inactive
Internal control active, single-burst, activate
Profile 0, then Profile 1, then stop
Internal control active, single-burst, activate
Profile 0, then Profile 1, then Profile 2, then stop
Internal control active, single-burst, activate
Profile 0, then Profile 1, then Profile 2, then
Profile 3, then stop
Internal control active, continuous, activate
Profile 0, then Profile 1, then Loop Starting 0
Internal control active, continuous, activate
Profile 0, then Profile 1, then Profile 2, then
Loop Starting 0
Internal control active, continuous, activate
Profile 0, then Profile 1, then Profile 2, then
Profile 3, and then Loop Starting 0
Invalid
A single-burst mode is one in which the composite sweep is
executed once. For example, assume the device is programmed
for ramp-up mode and the CFR1<29:27> bits are written to
Logic 010(b). Upon receiving an I/O update, the internal
control logic signals the device to begin executing the ramp-up
mode sequence for Profile 0. Upon reaching the RAM segment
final address value for Profile 0, the device jumps to the beginning
address of Profile 1 and begins executing that ramp-up sequence.
Upon reaching the RAM segment final address value for
Profile 1, the device jumps to the beginning address of Profile 2
and begins executing that ramp-up sequence. When the RAM
segment final address value for Profile 2 is reached, the
sequence is over and the composite sweep has completed.
Issuing another I/O update restarts the burst process.
A continuous internal profile control mode is one in which the
composite sweep is continuously executed for as long as the
device is programmed into that mode. Using the previous
example, except programming the CFR1<29:27> bits to
Logic 101(b), the operation would be identical until the RAM
segment final address value for Profile 2 is reached. At this
point, instead of stopping the sequence, the device jumps back
to the beginning address of Profile 0 and continues sweeping.
ramps from FTW0 to FTW1 and the RSRR register is loaded
into the sweep rate timer. When the timer counts down to one,
the frequency accumulator cycles once, increasing by the seed
value. This accumulation of the RDFTW at the rate given by the
ramp rate (RSRR) continues until the output of the frequency
adder is equal to the FTW1 register value, or PS0 is pulled low.
When PS0 is low, the 32-bit falling delta frequency tuning word
(FDFTW) is the seed value for the frequency accumulator, it
ramps down from FTW1 to FTW0 and the FSRR register is
loaded into the sweep rate timer. When the timer counts down
to one, the frequency accumulator cycles once, decreasing by
the seed value. This accumulation of the FDFTW at the rate
given by the ramp rate (FSRR) continues until the output of the
frequency adder is equal to the FTW0 register value, or PS0 is
pulled high.
Pin PS0 controls the direction of the sweep, rising to FTW1 or
falling to FTW0. Upon reaching the destination frequency, the
AD9954 linear sweep function either holds at the destination
frequency until the state on PS0 is changed or immediately
returns to the initial frequency, FTW0, depending on the state
of the Linear Sweep No-Dwell Bit CFR1<02>. While operating
in linear sweep mode, toggling PS0 does not cause the device to
generate an internal I/O update. When PS0 is acting as the
sweep direction indicator, any transfer of data from the I/O
buffers to the internal registers can only be initiated by a rising
edge on the I/O UPDATE pin.
The linear sweep function of the AD9954 requires the lowest
frequency to be loaded into the FTW0 register and the highest
frequency into the FTW1 register. For piece-wise, nonlinear
frequency transitions, it is necessary to reprogram the registers
while the frequency transition is in process.
After a reset, the device is initially in single-tone mode. The
programming steps to operate in linear sweep mode are:
0)
1)
2)
3)
Linear Sweep Mode
The AD9954 is placed in linear sweep mode using the Linear
Sweep Enable Bit CR1<21>. PS1 must be tied low. When in
linear sweep mode, the AD9954 output frequency ramps up
from a starting frequency, programmed by FTW0 to a finishing
frequency FTW1, or down from FTW1 to FTW0. The delta
frequency tuning words and the ramp rate word determine the
rate of this ramping. The Linear Sweep No-Dwell Bit CFR1<2>
controls the behavior of the device upon reaching the final
frequency.
When PS0 is high, the 32-bit rising delta frequency tuning word
(RDFTW) is the seed value for the frequency accumulator, it
4)
5)
PS1:0 = 00.
Set the linear sweep enable bit (CFR1<21>) and set or clear
the linear sweep no-dwell bit (CFR1<2>) as desired.
Program the rising and falling delta frequency tuning
words and ramp rate values.
Program the lower and higher output frequencies into the
FTW0 and FTW1 registers, respectively.
Apply an I/O update to move this data into the registers
(the instantaneous output frequency is FTW0).
Change the PS0 input as desired to sweep between the
lower to higher frequency and back.
Figure 21 depicts a typical frequency ramping operation. The
device initially powers up in single-tone mode. The profile
inputs are low, setting FTW0 as the seed value for the phase
accumulator. The user then writes to the linear sweep enable bit,
the rising and falling delta frequency tuning words, and ramp
rates via the serial port (Point A in Figure 21. In this example, the
linear sweep no-dwell bit is cleared (CFR1<2>).
Rev. B | Page 18 of 40
AD9954
fOUT
B
FTW1
A
FTW0
TIME
SINGLE-TONE
MODE
LINEAR SWEEP MODE
PS<0> = 1
PS<0> = 0
03374-003
PS<0> = 0
AT POINT A: LOAD RISING RAMP RATE REGISTER, APPLY RISING DFTW.
AT POINT B: LOAD FALLING RAMP RATE REGISTER, APPLY FALLING DFTW.
Figure 21. Linear Sweep Frequency Plan
fOUT
B
FTW1
A
FTW0
B
B
A
A
TIME
PS<0> = 0
PS<0> = 1 PS<0> = 0 PS<0> = 1
PS<0> = 0
PS<0> = 1
LINEAR SWEEP MODE ENABLE–NO DWELL BIT SET
03374-004
SINGLE-TONE
MODE
Figure 22. Linear Sweep Using No-Dwell Frequency Plan
Linear Sweep No-Dwell Feature
Resetting the Ramp Rate Timer
See CFR1<2> in the register maps (see Table 12 and Table 13)
for general details of the no-dwell mode. Figure 22 depicts the
linear sweep mode operation when the linear sweep no-dwell
bit is set. The Label A points indicate where a rising edge on
PS0 is detected; the Label B points indicate where the AD9954
has determined fOUT has reached the terminal frequency and
automatically returns to the starting frequency. Note that in this
mode, only sweeps from FTW0 to FTW1 using the positive
linear sweep control word are supported. Toggling PS0 from 1
to 0 neither initiates a falling sweep when the no-dwell bit is set,
nor interrupts a positive sweep already underway.
The ramp timer can be reset before reaching a count of 1 by
three methods.
Method one is by changing the PS0 input pin. When the PS0
input pin toggles from 0 to 1, the RSRRW value is loaded into
the ramp rate timer, which then proceeds to countdown as
normal. When the PS0 input pin toggles from 0 to 1, the falling
sweep ramp rate word (FSRRW) value is loaded into the ramp
rate timer, which then proceeds to countdown as normal.
The second method uses the LOAD SRR @ I/O UD bit
(CFR1<15>), see Table 12 for details.
Rev. B | Page 19 of 40
AD9954
The last method in which the sweep ramp rate timer can be
reset is changing from inactive linear sweep mode to active
linear sweep mode using the linear sweep enable bit (CFR1<21>).
For methods two and three, the ramp rate timer loads a value
determined by the state of PS0 (0 = FSRRW, 1 = RSRRW).
Power-Down Functions of the AD9954
The AD9954 supports an externally controlled (or hardware)
power-down feature as well as software-programmable powerdown bits capable of individually powering down specific unused
circuit blocks.
Software-controlled power-down enables individual powering
down of the DAC, comparator, PLL, input clock circuitry, and
the digital logic (CFR1<7:4>). With the exception of CFR1<6>,
these bits are superseded when the externally controlled powerdown pin (PWRDWNCTL) is high. External power-down
control is supported on the AD9954 via the PWRDWNCTL
input pin. When the PWRDWNCTL input pin is high, the
AD9954 enters a power-down mode based on the CFR1<3> bit.
When the PWRDWNCTL input pin is low, it operates normally.
See CFR1<3> in Table 12 for details.
Table 9 details the logic level for each power-down bit that
drives out of the AD9954 core logic to the analog section and
the digital clock generation section of the chip for the external
power-down operation.
Table 9. Power-Down Control Functions
Control
PWRDWNCTL = 0, CFR1<3> don’t care
Mode Active
Software control
PWRDWNCTL = 1, CFR1<3> = 0
External control, fast recovery
power-down mode
PWRDWNCTL = 1, CFR1<3> = 1
External control, full power-down
mode
Rev. B | Page 20 of 40
Description
Digital power-down = CFR1<7>
Comparator power-down = CFR1<6>
DAC power-down = CFR1<5>
Clock input power-down = CFR1<4>
Digital power-down = 1’b1
Comparator power-down = 1’b0 or CFR1<6>
DAC power-down = 1’b0
Clock input power-down = 1’b0
Digital power-down = 1’b1
Comparator power-down = 1’b1
DAC power-down = 1’b1
Clock input power-down = 1’b1
AD9954
The I/O update signal coupled with SYNC_CLK is used to
transfer internal buffer contents into the control registers. The
combination of the SYNC_CLK pin and the I/O UPDATE pin
provides the user with constant latency relative to SYSCLK and
ensures phase continuity of the analog output signal when a
new tuning word or phase offset value is asserted.
SYNCHRONIZATION—REGISTER UPDATES (I/O
UPDATE)
Functionality of the SYNC_CLK and I/O UPDATE
Data into the AD9954 is synchronous to the SYNC_CLK
signal (supplied externally to the user on the SYNC_CLK pin).
The I/O UPDATE pin is sampled on the rising edge of the
SYNC_CLK.
Figure 23 and Figure 24 demonstrate an I/O update timing
cycle and synchronization.
Internally, SYSCLK is fed to a divide-by-four frequency divider
to produce the SYNC_CLK signal. The SYNC_CLK signal is
made available to the system on the SYNC_CLK pin. This
enables synchronization of external hardware with the device’s
internal clocks. This is accomplished by providing the SYNC_CLK
signal as an output that external hardware can then use to
synchronize against.
Synchronization logic notes include the following:
 The I/O update signal is edge detected to generate a singlecycle clock signal that drives the register bank flops. The I/O
update signal has no constraints on duty cycle. The minimum
low time on I/O update is one SYNC_CLK clock cycle.
 The I/O UPDATE pin is set up and held around the rising
edge of SYNC_CLK. Setup and hold time specifications can
be found in Table 2.
SYNC_CLK
DISABLE
1
0
SYSCLK
0
÷4
OSK
PS<1:0>
D
I/O UPDATE
D
Q
D
Q
Q
EDGE
DETECTION
LOGIC
TO CORE LOGIC
REGISTER
MEMORY
SCLK
SDIO
CS
I/O BUFFER
LATCHES
03374-006
SYNC_CLK
GATING
Figure 23. I/O Synchronization Block Diagram
SYSCLK
A
B
SYNC_CLK
I/O UPDATE
DATA IN
I/O BUFFERS
N
N–1
N
N+1
THE DEVICE REGISTERS AN I/O UPDATE AT POINT A. THE DATA IS TRANSFERRED FROM
THE ASYNCHRONOUSLY LOADED I/O BUFFERS AT POINT B.
Figure 24. I/O Synchronization Timing Diagram
Rev. B | Page 21 of 40
N+1
N+2
03374-007
DATA IN
REGISTERS
AD9954
Synchronizing Multiple AD9954s
RAM
There are three modes of synchronization available to the user:
an automatic synchronization mode, a software-controlled
manual synchronization mode, and a hardware-controlled
manual synchronization mode. The following requirements
apply to all modes. First, all units must share a common clock
source. Trace lengths and path impedance of the clock tree must
be designed to keep the phase delay of the different clock branches
as closely matched as possible. Second, the I/O update signal’s
rising edge must be provided synchronously to all devices being
synchronized. Finally, the DVDD_I/O supply should be set to
3.3 V for all devices that are to be synchronized. AVDD and
DVDD should be left at 1.8 V.
The AD9954 incorporates a block of SRAM. The RAM is a
bidirectional single port. Read and write operations cannot
occur simultaneously. Write operations to the serial I/O port
take precedence; therefore, if an attempt to write to RAM is
made during a read operation, the read operation is halted. The
RAM is configurable using the RAM Segment Control Word<7:5>
and data in the control function register.
In automatic synchronization mode, one device is chosen as a
master, the other device(s) is slaved to this master. All slaves
automatically synchronize their internal clocks to the SYNC_CLK
output signal of the master device. Use the automatic
synchronization bit (CFR1<23>) to configure each slave.
Connect the SYNC_IN input(s) to the master SYNC_CLK
output. Slave devices continuously update the phase relationship of
their SYNC_CLK until it is in phase with the SYNC_IN input.
The high speed sync enhancement enable bit (CFR2<11>) must
be programmed correctly.
In software manual synchronization mode, the user can force
the device to advance the SYNC_CLK rising edge one SYSCLK
cycle (¼ SYNC_CLK period). Manual synchronization mode
is established using the slave device’s software manual
synchronization bit (CFR1<22>). See the bit description in
Table 12 for more details.
In hardware manual synchronization mode, the SYNC_IN
input pin is configured such that it now advances the rising edge
of the SYNC_CLK signal each time the device detects a rising edge
on the SYNC_IN pin. Hardware manual synchronization mode is
established using the hardware manual synchronization bit
(CFR2<10>). See the bit description in Table 12 for more details.
Using a Single Crystal to Drive Multiple AD9954 Clock
Inputs
The AD9954 crystal oscillator output signal is available on the
CRYSTAL OUT pin, enabling one crystal to drive multiple
AD9954s. To drive multiple AD9954s with one crystal, the
CRYSTAL OUT pin of the AD9954 using the external crystal
should be connected to the REFCLK input of the other AD9954.
The CRYSTAL OUT pin must be enabled using the CRYSTAL
OUT Pin Active Bit CFR2<9>. The drive strength of the
CRYSTAL OUT pin is fairly low; therefore, the signal
should be buffered if multiple loads are being driven.
Using the RAM enable bit (CFR1<31>), the RAM output can be
enabled to drive the input to either the phase accumulator or
the phase offset adder; the RAM destination bit (CFR1<30>)
sets the routing. When the RAM output drives the phase
accumulator, the phase offset word (POW, Address 0x05) drives
the phase-offset adder. Conversely, when the RAM output
drives the phase-offset adder, the frequency tuning word (FTW,
Address 0x04) drives the phase accumulator. When CFR1<31>
disables the RAM, it is inactive unless being written to via the
serial port. The RAM is mapped into one of four profiles
determined by the PS1 and PS0 input pins. Note that these
profiles may overlap. For example, Profile 0 may use RAM
Address Location 0 to Address Location 12, and Profile 1 may use
RAM Address Location 5 to Address Location 20, and so forth.
All RAM write or read operations to/from the RAM are
controlled by the PS1 and PS0 input pins and the respective
RAM segment control word. To write to the RAM, a RAM
segment must be defined in a RAM segment control word. The
RAM segment that was defined must then be selected by use of
the profile select pins, PS0 and PS1. With the correct RAM
segment selected, the special instruction byte of 0xB0 should
be sent. When the instruction byte to write to the RAM is sent
to the part, the serial port controller immediately polls the
corresponding RAM segment control word. From this register,
the serial port controller makes note of the start address and the
stop address. It then calculates how many entries there are in
the segment, and how many bytes of data to expect. After
sending the special instruction byte of 0xB0, the user must send
all RAM entries for the currently selected profile to the part.
For example, consider a case where RAM Segment 2 begins at
Address 21 and ends at Address 120. First, write to RAM Segment
Control Word 2 with a starting address of 21, with a stop address
of 120, and specify a ramp rate and a mode of operation. Next, set
PS1 to 1 and PS0 to 0 to select RAM Segment 2 and then send
the instruction byte of 0xB0. The part is now ready to put the first
32-bit word into the RAM at Address 21, to expect 100 32-bit
words, and to store the last one at Address 120. It automatically
controls sending the data from the serial port to the correct RAM
address. Therefore, precede sending 100 32-bit words of data to
the part. After the 3200th SCLK cycle, the write operation is
complete, and all 100 words are stored in the RAM, from
Address 21 to Address 120.
Rev. B | Page 22 of 40
AD9954
Serial I/O Port
There are two phases to a communication cycle with the
AD9954. Phase 1 is the instruction cycle, which is the writing of
an instruction byte into the AD9954, coincident with the first
eight SCLK rising edges. The instruction byte provides the
AD9954 serial port controller with information regarding
Phase 2, the data transfer cycle. The instruction byte defines
whether the upcoming data transfer is a read or a write and the
serial address of the register being accessed.
The AD9954 serial port is a flexible, synchronous, serial
communications port that easily interfaces to many industrystandard microcontrollers and microprocessors. The serial I/O port
is compatible with most synchronous transfer formats, including
both the Motorola 6905/11 SPI® and Intel® 8051 SSR protocols.
The interface accesses all registers that configure the AD9954. MSB
first and LSB first transfer formats are supported. In addition, the
AD9954’s serial interface port can be configured as a single pin I/O
(SDIO), which allows a 2-wire interface, or two unidirectional pins
for in/out (SDIO/SDO), which enables a 3-wire interface. Two
optional pins, IOSYNC and CS, provide further flexibility for
system design with the AD9954.
The first eight SCLK rising edges of each communication cycle
are used to write the instruction byte into the AD9954. The
remaining SCLK edges are for Phase 2 of the communication
cycle. Phase 2 is the actual data transfer between the AD9954
and the system controller. The number of bytes transferred
during Phase 2 of the communication cycle is a function of the
register being accessed. For example, when accessing the Control
Function Register 2, which is three bytes wide, Phase 2 requires that
three bytes be transferred. If accessing the frequency tuning word,
which is four bytes wide, four bytes must be transferred. After
transferring all data bytes per the instruction byte, the
communication cycle is complete.
SERIAL PORT OPERATION
With the AD9954, the instruction byte specifies read/write
operation and register address. Serial operations on the AD9954
only occur at the register level, they do not occur on the byte
level. For the AD9954, the serial port controller recognizes the
instruction byte register address and automatically generates the
proper register byte address. In addition, the controller expects
to access all bytes of that register. It is a requirement that all
bytes of a register be accessed during serial I/O operations, with
one exception; the IOSYNC function can be used to abort an
I/O operation, thereby allowing less than all bytes to be
accessed.
At the completion of any communication cycle, the AD9954
serial port controller expects the next eight rising SCLK edges
to be the instruction byte of the next communication cycle. All
data input to the AD9954 is registered on the rising edge of
SCLK. All data is driven out of the AD9954 on the falling edge
of SCLK. Figure 25 through Figure 28 are provided to aid in
understanding the general operation of the AD9954 serial port.
INSTRUCTION CYCLE
DATA TRANSFER CYCLE
CS
SDIO
I7
I6
I5
I4
I3
I2
I1
I0
D7
D6
D5
D4
D3
D2
D1
03374-008
SCLK
D0
Figure 25. Serial Port Write Timing–Clock Stall Low
INSTRUCTION CYCLE
DATA TRANSFER CYCLE
CS
SCLK
I7
I6
I5
I4
I3
I2
I1
I0
DON'T CARE
DO 7
SDO
DO 6 DO 5 DO 4 DO 3 DO 2 DO 1
DO 0
03374-009
SDIO
Figure 26. 3-Wire Serial Port Read Timing–Clock Stall Low
INSTRUCTION CYCLE
DATA TRANSFER CYCLE
CS
SDIO
I7
I6
I5
I4
I3
I2
I1
I0
D7
D6
D5
D4
Figure 27. Serial Port Write Timing–Clock Stall High
Rev. B | Page 23 of 40
D3
D2
D1
D0
03374-010
SCLK
AD9954
INSTRUCTION CYCLE
DATA TRANSFER CYCLE
CS
SDIO
I7
I6
I5
I4
I3
I2
I1
I0
DO 7 DO 6 DO 5 DO 4 DO 3 DO 2 DO 1 DO 0
03374-011
SCLK
Figure 28. 2-Wire Serial Port Read Timing—Clock Stall High
SCLK—Serial Clock. The serial clock pin is used to synchronize
data to and from the AD9954 and to run internal state machines.
SCLK maximum frequency is 25 MHz.
CS—Chip Select. CS is an active low input that enables
devices sharing a serial communications line to be individually
programmed. The SDO and SDIO pins go to a high impedance
state when this input is high. If driven high during any
communications cycle, that cycle is suspended until CS is
reactivated low. Chip select can be tied low if it is not needed.
SDIO —Serial Data I/O. Data written to the AD9954 must be
sent to this pin. However, this pin can be used as a bidirectional
data line. CFR1<9> controls the configuration of this pin.
SDO—Serial Data Out. Data is read from this pin for protocols
that use separate lines for transmitting and receiving data.
When in 2-wire serial programming mode, this pin is set to a
high impedance state.
the register at this memory location and notes that the ASF is
2 bytes wide. The serial port controller’s state machines sets to
16 and awaits 16 rising edges on the SCLK and 16 bits of data
on the SDIO line. Send 16 rising edges on SCLK, and the binary
data 10000000 00000000 on the SDIO line.
To write the amplitude scale factor register in LSB first format,
the process is the same as in MSB first; however, the data is bit
wise inverted on a word-by-word basis. The instruction byte is
0x40. The binary data for the ASF is 00000000 00000001.
CS
●●●
SCLK
●●●
●●●
SDIO
TCSU
IOSYNC—synchronizes the I/O port state machines without
affecting the addressable registers contents. An active high input
on the IOSYNC pin aborts the current communication cycle. After
IOSYNC returns low (Logic 0), another communication cycle may
begin, starting with the instruction byte write.
TDSU
TDH
DVDD I/O = 3.3V
DVDD I/O = 1.8V
TCSU = 3ns
TDSU = 3ns
TDH = 0ns
TCSU = 5ns
TDSU = 5ns
TDH = 0ns
TDH
03374-036
SERIAL INTERFACE PORT PIN DESCRIPTIONS
Figure 29. Timing Diagram for Data Write to AD9954
SCLK
MSB/LSB TRANSFERS
The AD9954 serial port can support either MSB first or LSB
first data formats. This functionality is controlled by the LSB
First Bit CFR1<8>.
If the LSB mode is active, the serial port controller generates the
least significant byte address first followed by the next greater
significant byte addresses until the I/O operation is complete.
All data written to (read from) the AD9954 must be in LSB
first order.
Example Operation
As an example, consider the case of writing the amplitude scale
factor (ASF) register to a value of 0.5 full scale. First, calculate
the binary equivalent of 0.5. As the ASF is 16 bits wide, the
hexadecimal equivalent is 0x80. Next, for MSB first format,
transmit an instruction byte of 0x02 (serial address of ASF is
00010(b)). From this instruction, the internal controller polls
TDV = 25ns
03374-037
For MSB first operation, the serial port controller generates the
most significant byte (of the specified register) address first
followed by the next lesser significant byte addresses until the
I/O operation is complete. All data written to (read from) the
AD9954 must be in MSB first order.
SDIO
SDO
Figure 30. Timing Diagram for Data Read to AD9954
RAM I/O VIA SERIAL PORT
Accessing the RAM via the serial port is identical to any other
serial I/O operation except that the number of bytes transferred
is determined by the address space between the beginning
address and the final address as specified in the current RAM
segment control word (RSCW). The final address describes the
most significant word address for all I/O transfers and the
beginning address specifies the least significant address.
RAM I/O supports MSB/LSB first operation as set using the
LSB First Bit CFR1<8>. When in MSB first mode, the first data
byte is for the most significant byte of the memory address
described by the final address with the remaining three bytes
making up the lesser significant bytes of that address. The
remaining bytes come in most significant to least significant,
destined for RAM addresses generated in descending order
Rev. B | Page 24 of 40
AD9954
until the final four bytes are written into the address specified as
the beginning address. When in LSB first mode, the first data
byte is for the least significant byte of the memory (specified by
the beginning address) with the remaining three bytes making
up the greater significant bytes of that address. The remaining
bytes come in least significant to most significant, destined for
RAM addresses generated in ascending order until the final
four bytes are written into the memory address described by the
final address.
The RAM uses Serial Address 01011(b); therefore, the
instruction byte to write the RAM is 0x0B, in MSB first notation.
As previously mentioned, the RAM addresses generated are
specified by the beginning and final address of the RSCW
currently selected by Pin PS1 and Pin PS0.
Notes on serial port operation
 The configuration changes made using CFR1<9:8> are
implemented immediately upon writing to this register. For
multibyte transfers, writing to this register may occur during
the middle of a communication cycle. Care must be taken to
compensate for this new configuration for the remainder of
the current communication cycle.
 The system must maintain synchronization with the AD9954
or the internal control logic cannot recognize further
instructions. For example, if the system sends an instruction
byte that describes writing a 2-byte register, and then pulses
the SCLK pin for a 3-byte write (24 additional SCLK rising
edges), communication synchronization is lost. In this case,
the first 16 SCLK rising edges after the instruction cycle
properly write the first two data bytes into the AD9954, but
the next eight rising SCLK edges are interpreted as the next
instruction byte. In the case where synchronization is lost
between the system and the AD9954, the IOSYNC pin
enables the user to reset the AD9954 serial port controller
state machine. Any information that is written to the AD9954
registers during a valid communication cycle prior to loss of
synchronization and assertion of the IOSYNC pin remain intact.
 Reading a RAM profile requires that the profile select pins,
Pin PS1 and Pin PS0, be configured to select the desired profile.
When reading a register that resides in one of the profiles, the
register address acts as an offset to select one of the registers
among the group of registers defined by the profile, while the
profile select pins select the appropriate register group.
INSTRUCTION BYTE
The instruction byte contains the following information.
Table 10.
MSB
R/W
D6
X
D5
X
D4
A4
D3
A3
D2
A2
D1
A1
LSB
A0
R/W—Bit 7 of the instruction byte defines whether a read or
write data transfer occurs after the instruction byte write. Logic
High indicates read operation. Logic 0 indicates a write
operation.
X, X—Bit 6 and Bit 5 of the instruction byte are don’t care.
A4, A3, A2, A1, A0—Bit 4, Bit 3, Bit 2, Bit 1, Bit 0 of the
instruction byte determine which register is accessed during the
data transfer portion of the communications cycle. Addresses for
registers can be found in the first column of the register maps (see
Table 12 and Table 13).
REGISTER MAPS AND DESCRIPTIONS
The register maps are listed in Table 12 and Table 13. The active
register map depends on the state of the linear sweep enable bit;
certain registers are remapped depending on which mode the
part is operating in. Specifically, Register 0x07, Register 0x08,
Register 0x09, and Register 0x0A are affected. Because the
linear sweep operation takes precedence over RAM operations,
Analog Devices, Inc. recommends that the RAM be disabled
using Bit CFR1<31> when linear sweep is enabled by Bit
CFR1<21> to conserve power. The serial address numbers
associated with each of the registers are in hexadecimal format.
Angle brackets <> are used to reference specific bits or ranges of
bits. For example, <3> designates Bit 3 and <7:3> designates the
range of bits from Bit 7 to Bit 3, inclusive.
Table 11. Register Mapping Based on Linear Sweep Enable Bit
Linear Sweep Enable Bit
(CFR1<21>)
Cleared (= 0)
Set (= 1)
Rev. B | Page 25 of 40
Register Map
RAM Segment Control Words Active
Linear Sweep Control Words Active
AD9954
Table 12. Register Map—When Linear Sweep Enable Bit Is False (CFR1<21> = 0)
Note that the RAM Enable Bit CFR1<31> only activates the RAM itself, not the RAM segment control words.
Register
Name
(Serial
Address)
Control
Function
Register
No.1
(CFR1)
(0x00)
Bit
Range
<7:0>
(MSB)
Bit 7
Digital
PowerDown
<15:8>
SRR Load
Enable
<23:16>
Automatic
Sync
Enable
RAM
Enable
<31:24>
Control
Function
Register
No. 2
(CFR2)
(0x01)
Amplitude
Scale
Factor (ASF)
(0x02)
Amplitude
Ramp Rate
(ARR)
(0x03)
Frequency
Tuning
Word
(FTW0)
(0x04)
Phase
Offset Word
(POW0)
(0x05)
Frequency
Tuning
Word
(FTW1)
(0x06)
Profile 0
RAM
Segment
Control
Word No. 0
(RSCW0)
(0x07)
Bit 6
Comp
PowerDown
Bit 5
DAC
PowerDown
AutoClr
Freq
Accum
Software
Manual
Sync
RAM
Destination
AutoClr
Phase
Accum
Linear
Sweep
Enable
Internal Profile Control<2:0>
<7:0>
Bit 4
Clock
Input
PowerDown
Sine/
Cosine
Select
Not Used
REFCLK Multiplier
<15:8>
Not Used
Bit 3
External
PowerDown
Mode
Clear
Freq
Accum
Not
Used
Bit 2
Linear
Sweep
NoDwell
Clear
Phase
Accum
Not Used
Bit 1
SYNC_CLK
Disable
Load ARR
Control
OSK
Enable
VCO
Range
Hardware
Manual
Sync
Enable
SDIO
Input
Only
Not Used
(LSB)
Bit 0
Not
Used
Default
Value Or
Profile
0x00
LSB First
0x00
Not
Used
0x00
Auto
OSK
Enable
Charge Pump
Current<1:0>
XTAL
Not
OUT
Used
Enable
0x00
0x00
0x00
High
Speed
Sync
Enable
Not Used
Amplitude Scale Factor Register<7:0>
Amplitude Scale Factor Register<13:8>
0x18
0x00
0x00
<7:0>
Amplitude Ramp Rate Register<7:0>
0x00
<7:0>
<15:8>
<23:16>
<31:24>
Frequency Tuning Word No. 0<7:0>
Frequency Tuning Word No. 0<15:8>
Frequency Tuning Word No. 0<23:16>
Frequency Tuning Word No. 0<31:24>
0x00
0x00
0x00
0x00
<23:16>
<7:0>
<15:8>
<7:0>
<15:8>
<7:0>
<15:8>
<23:16>
<31:24>
<7:0>
<15:8>
<23:16>
Auto Ramp Rate
Speed Control<1:0>
Not Used<1:0>
Phase Offset Word No. 0<7:0>
Phase Offset Word No. 0<13:8>
Frequency Tuning Word No. 1<7:0>
Frequency Tuning Word No. 1<15:8>
Frequency Tuning Word No. 1<23:16>
Frequency Tuning Word No. 1<31:24>
RAM Segment 0 Beginning Address<9:6>
RAM Segment 0 Mode
No-Dwell
Control<2:0>
Active
RAM Segment 0 Beginning Address<5:0>
RAM Segment 0
Final Address<9:8>
RAM Segment 0 Final Address<7:0>
<31:24>
RAM Segment 0 Address Ramp Rate<15:8>
<39:32>
RAM Segment 0 Address Ramp Rate<7:0>
Rev. B | Page 26 of 40
0x00
0x00
0x00
0x00
0x00
0x00
PS0 = 0
PS1 = 0
PS0 = 0
PS1 = 0
PS0 = 0
PS1 = 0
PS0 = 0
PS1 = 0
PS0 = 0
PS1 = 0
AD9954
Register
Name
(Serial
Address)
Profile 1
RAM
Segment
Control
Word No. 1
(RSCW1)
(0x08)
Profile 2
RAM
Segment
Control
Word No. 2
(RSCW2)
(0x09)
Profile 3
RAM
Segment
Control
Word No. 3
(RSCW3)
(0x0A)
RAM (0x0B)
Bit
Range
<7:0>
<15:8>
(MSB)
Bit 7
(LSB)
Bit 3
Bit 2
Bit 1
Bit 0
RAM Segment 1 Beginning Address<9:6>
Bit 6
Bit 5
Bit 4
RAM Segment 1 Mode
No-Dwell
Control<2:0>
Active
RAM Segment 1 Beginning Address<5:0>
<23:16>
RAM Segment 1 Final Address<7:0>
<31:24>
RAM Segment 1 Address Ramp Rate<15:8>
<39:32>
RAM Segment 1 Address Ramp Rate<7:0>
<7:0>
<15:8>
RAM Segment 2 Mode
No-Dwell
Control<2:0>
Active
RAM Segment 2 Beginning Address <5:0>
RAM Segment 2 Beginning Address<9:6>
<23:16>
RAM Segment 2 Final Address<7:0>
<31:24>
RAM Segment 2 Address Ramp Rate<15:8>
<39:32>
RAM Segment 2 Address Ramp Rate<7:0>
<7:0>
<15:8>
<23:16>
RAM Segment 1
Final Address<9:8>
RAM Segment 2
Final Address<9:8>
RAM Segment 3 Beginning Address<9:6>
RAM Segment 3 Mode
No-Dwell
Control<2:0>
Active
RAM Segment 3 Beginning Address<5:0>
RAM Segment 3
Final Address <9:8>
RAM Segment 3 Final Address<7:0>
<31:24>
RAM Segment 3 Address Ramp Rate<15:8>
<39:32>
RAM Segment 3 Address Ramp Rate<7:0>
RAM [1023:0]<31:0> (Read Instructions Write Out RAM Signature Register Data)
Rev. B | Page 27 of 40
Default
Value Or
Profile
PS0 = 1
PS1 = 0
PS0 = 1
PS1 = 0
PS0 = 1
PS1 = 0
PS0 = 1
PS1 = 0
PS0 = 1
PS1 = 0
PS0 = 0
PS1 = 1
PS0 = 0
PS1 = 1
PS0 = 0
PS1 = 1
PS0 = 0
PS1 = 1
PS0 = 0
PS1 = 1
PS0 = 1
PS1 = 1
PS0 = 1
PS1 = 1
PS0 = 1
PS1 = 1
PS0 = 1
PS1 = 1
PS0 = 1
PS1 = 1
AD9954
Table 13. Register Map—When Linear Sweep Enable Bit Is True (CFR1<21> = 1)
Note that the RAM Enable Bit CFR1<31> only activates the RAM itself, not the RAM segment control words.
Register Name
(Serial Address)
Control
Function
Register No. 1
(CFR1)
(0x00)
Bit
Range
<7:0>
(MSB)
Bit 7
Digital
PowerDown
<15:8>
SRR Load
Enable
<23:16>
Automatic
Sync
Enable
RAM
Enable
<31:24>
Control
Function
Register
No. 2 (CFR2)
(0x01)
Amplitude
Scale Factor
(ASF) (0x02)
Amplitude
Ramp Rate
(ARR) (0x03)
Frequency
Tuning
Word
(FTW0)
(0x04)
Phase Offset
Word (POW0)
(0x05)
Frequency
Tuning
Word (FTW1)
(0x06)
Negative
Linear
Sweep
Control
Word (NLSCW)
(0x07)
Positive
Linear
Sweep
Control
Word (PLSCW)
(0x08)
Bit 6
Comp
PowerDown
Bit 5
DAC
PowerDown
AutoClr
Freq
Accum
Software
Manual
Sync
RAM
Destination
AutoClr
Phase
Accum
Linear
Sweep
Enable
Internal Profile Control<2:0>
<7:0>
REFCLK Multiplier
<15:8>
<23:16>
<7:0>
(0x07)
<15:8>
Bit 4
Clock
Input
Power
Down
Sine/
Cosine
Select
Not
Used
Not Used
Auto Ramp Rate
Speed Control<1:0>
Bit 3
External
PowerDown
Mode
Clear
Freq
Accum
Not
Used
Bit 2
Linear
Sweep
No Dwell
Bit 1
SYNC_CLK
Disable
Clear
Phase
Accum
Not Used
SDIO
Input
Only
Not Used
Load ARR
Control
OSK
Enable
VCO
Range
Hardware
Manual
Sync
Enable
High
Speed
Sync
Enable
Not Used
Amplitude Scale Factor Register<7:0>
Amplitude Ramp Rate Register<7:0>
<7:0>
<15:8>
<23:16>
<31:24>
Frequency Tuning Word No. 0<7:0>
Frequency Tuning Word No. 0<15:8>
Frequency Tuning Word No. 0<23:16>
Frequency Tuning Word No. 0<31:24>
<7:0>
<15:8>
<23:16>
<31:24>
<7:0>
<15:8>
<23:16>
<31:24>
<39:32>
<7:0>
<15:8>
<23:16>
<31:24>
<39:32>
Open<1:0>
Default
Value Or
Profile
0x00
LSB
First
0x00
Not
Used
0x00
Auto
OSK
Enable
Charge Pump
Current<1:0>
XTAL
Not
OUT
Used
Enable
0x00
0x00
0x00
0x18
Amplitude Scale Factor Register<13:8>
<7:0>
<7:0>
<15:8>
(LSB)
Bit 0
Not
Used
Phase Offset Word No. 0<7:0>
Phase Offset Word No. 0<13:8>
Frequency Tuning Word No. 1<7:0>
Frequency Tuning Word No. 1<15:8>
Frequency Tuning Word No. 1<23:16>
Frequency Tuning Word No. 1<31:24>
Falling Delta Frequency Tuning Word<7:0>
Falling Delta Frequency Tuning Word<15:8>
Falling Delta Frequency Tuning Word<23:16>
Falling Delta Frequency Tuning Word<31:24>
Falling Sweep Ramp Rate Word<7:0>
Rising Delta Frequency Tuning Word<7:0>
Rising Delta Frequency Tuning Word<15:8>
Rising Delta Frequency Tuning Word<23:16>
Rising Delta Frequency Tuning Word <31:24>
Rising Sweep Ramp Rate Word<7:0>
Rev. B | Page 28 of 40
0x00
0x00
0x00
0x00
0x00
0x00
PS0 = 0
PS0 = 0
PS0 = 0
PS0 = 0
PS0 = 0
PS0 = 1
PS0 = 1
PS0 = 1
PS0 = 1
PS0 = 1
AD9954
CONTROL REGISTER BIT DESCRIPTIONS
Control Function Register No. 1 (CFR1)
The CFR1 is used to control the various functions, features,
and modes of the AD9954. The functionality of each bit follows.
CFR1<31>: RAM Enable Bit
CFR1<31> = 0 (default). The RAM is disabled for operation.
Either single-tone mode of operation or linear sweep mode of
operation is enabled.
CFR1<31> = 1. The RAM is enabled for operation. Access
control for normal operation is controlled via the mode control
bits of the RSCW for the current profile.
CFR1<22>: Software Manual Synchronization of Multiple
AD9954s
CFR1<22> = 0 (default). The manual synchronization feature is
inactive.
CFR1<22> = 1. The software-controlled manual synchronization
feature is executed. The SYNC_CLK rising edge is advanced by
one SYNC_CLK cycle, and this bit is autocleared. To advance
the rising edge multiple times, this bit needs to be set once for
each advance.
CFR1<21>: Linear Frequency Sweep Enable
CFR1<21> = 0 (default). The linear frequency sweep capability
of the AD9954 is inactive.
CFR1<30>: RAM Destination Bit
If CFR1<31> is cleared, CFR1<30> is ignored.
CFR1<30> = 0 (default). If CFR1<31> is set, the RAM output
drives the phase accumulator (provides the FTW).
CFR1<30> = 1. If CFR1<31> is set, the RAM output drives the
phase-offset adder (POW).
CFR1<29:27>: Internal Profile Control Bits
These bits cause the profile bits to be ignored when the RAM is
being used and puts the AD9954 into an automatic profile loop
sequence that allows the user to implement a frequency/phase
composite sweep that runs without external inputs. See the
Internal Profile Control section for more details.
CFR1<21> = 1. The linear frequency sweep capability of the
AD9954 is enabled. See the Linear Sweep Mode section for details.
CFR1<20:16>: Not Used, Leave Clear
CFR1<15>: Linear Sweep Ramp Rate Load Control Bit
CFR1<15> = 0 (default). The linear sweep ramp rate timer is
loaded only upon timeout (timer == 1); it is not loaded due to
an I/O update input signal.
CFR1<15> = 1. The linear sweep ramp rate timer is loaded
either upon timeout (timer == 1) or at the time of an I/O
update input signal.
CFR1<26>: Load Amplitude Ramp Rate Control Bit
CFR1<14>: Autoclear Frequency Accumulator Bit
CFR1<26> = 0 (default). The amplitude ramp rate timer is
loaded only upon timeout (timer == 1); it is not loaded due to
an I/O update input signal.
CFR1<14> = 0 (default). The current state of the frequency
accumulator is not impacted by receipt of an I/O update signal.
CFR1<26> = 1. The amplitude ramp rate timer is loaded upon
either timeout (timer == 1) or at the time of an I/O update
input signal.
CFR1<13>: Autoclear Phase Accumulator Bit
CFR1<25>: Shaped On-Off Keying Enable Bit
CFR1<13> = 0 (default). The current state of the phase
accumulator is not impacted by receipt of an I/O update signal.
CFR1<25> = 0 (default). Shaped on-off keying is bypassed.
CFR1<13> = 1. The phase accumulator is automatically and
synchronously cleared for one cycle upon receipt of an I/O
update signal.
CFR1<25> = 1. Shaped on-off keying is enabled. See also
CFR1<24>.
CFR1<24>: Autoshaped On-Off Keying Enable Bit
CFR1<12>: Sine/Cosine Select Bit
If CFR1<25> is cleared, CFR1<24> is ignored.
CFR1<24> = 0 (default). Manual shaped on-off keying
operation. See the Shaped On-Off Keying section for details.
CFR1<24> = 1. Autoshaped on-off keying operation. See the
Shaped On-Off Keying section for details.
CFR1<12> = 0 (default). The angle-to-amplitude conversion
logic employs a cosine function.
CFR1<12> = 1. The angle-to-amplitude conversion logic
employs a sine function.
CFR1<11>: Clear Frequency Accumulator
CFR1<23>: Automatic Synchronization Enable Bit
CFR1<23> = 0 (default). The automatic synchronization feature
of multiple AD9954s is inactive.
CFR1<23> = 1. The automatic synchronization feature of
multiple AD9954s is active. See the Synchronizing Multiple
AD9954s section for details.
CFR1<14> = 1. The frequency accumulator is automatically and
synchronously cleared for one cycle upon receipt of an I/O
UPDATE signal.
CFR1<11> = 0 (default). The frequency accumulator functions
as normal.
CFR1<11> = 1. The frequency accumulator memory elements
are cleared and held clear until this bit is cleared.
Rev. B | Page 29 of 40
AD9954
CFR1<10>: Clear Phase Accumulator
CFR1<2>: Linear Sweep No-Dwell Bit
CFR1<10> = 0 (default). The phase accumulator functions as
normal.
If CFR1<21> is clear, this bit is a don’t care (ignored).
CFR1<10> = 1. The phase accumulator memory elements are
cleared and held clear until this bit is cleared.
CFR1<9>: SDIO Input Only
CFR1<9> = 0 (default). The SDIO pin is bidirectional (2-wire
serial programming mode).
CFR1<2> = 0 (default). The linear sweep no-dwell function is
inactive. If the no-dwell mode is inactive when the sweep
completes, sweeping does not restart until an I/O update or
change in profile initiates another sweep as previously described.
The output frequency holds at the final value in the sweep.
CFR1<8>: LSB First
CFR1<2> = 1. The linear sweep no-dwell function is active. If
the no-dwell mode is active when the sweep completes, the
phase accumulator is cleared. The phase accumulator remains
cleared until another sweep is initiated via an I/O update input
or change in profile.
CFR1<8> = 0 (default). MSB first format is active.
CFR1<1>: SYNC_CLK Disable Bit
CFR1<8> = 1. LSB first format is active.
CFR1<1> = 0 (default). The SYNC_CLK pin is active.
CFR1<7>: Digital Power-Down Bit
CFR1<1> = 1. The SYNC_CLK pin assumes a static Logic 0
state to minimize noise generated by the digital circuitry. The
synchronization circuitry remains active internally to maintain
normal device timing.
CFR1<9> = 1. The SDIO is configured as an input-only pin
(3-wire serial programming mode).
CFR1<7> = 0 (default). All digital functions and clocks are active.
CFR1<7> = 1. All non-I/O digital functionality is suspended,
lowering the power significantly.
CFR1<6>: Comparator Power-Down Bit
CFR1<0>: Not Used, Leave Clear
Control Function Register No. 2 (CFR2)
CFR1<6> = 0 (default). The comparator is enabled for operation.
CFR1<6> = 1. The comparator is disabled and is in its lowest
power dissipation state.
The CFR2 is used to control the various functions, features, and
modes of the AD9954, primarily related to the analog sections
of the chip.
CFR1<5>: DAC Power-Down Bit
CFR2<23:12>: Not Used, Leave Clear
CFR1<5> = 0 (default). The DAC is enabled for operation.
CFR2<11>: High Speed Sync Enable Bit
CFR1<5> = 1. The DAC is disabled and is in its lowest power
dissipation state.
CFR2<11> = 0 (default). The high speed sync enhancement is off.
CFR1<4>: Clock Input Power-Down Bit
CFR1<4> = 0 (default). The clock input circuitry is enabled for
operation.
CFR1<4> = 1. The clock input circuitry is disabled and the
device is in its lowest power dissipation state.
CFR2<11> = 1. The high speed sync enhancement is on. This
bit should be set when using the autosynchronization feature
for SYNC_CLK > 50 MHz (SYSCLK > 200 MSPS).
CFR2<10>: Hardware Manual Sync Enable Bit
CFR2<10> = 0 (default). The hardware manual sync function is off.
CFR1<3>: External Power-Down Mode
CFR1<3> = 0 (default). The external power-down mode
selected is the rapid recovery power-down mode. In this mode,
when the PWRDWNCTL input pin is high, the digital logic
and the DAC digital logic are powered down. The DAC bias
circuitry, PLL, oscillator, and clock input circuitry are not
powered down. CFR1<6> determines whether the comparator
is powered down. CFR1<7>, and CFR1<5:4> are ignored.
CFR1<3> = 1. The external power-down mode selected is the
full power-down mode. In this mode, when the PWRDWNCTL
input pin is high, all functions are powered down. This includes
the DAC and PLL, which take a significant amount of time to
power up. CFR1<7:4> are all ignored.
CFR2<10> = 1. The hardware manual sync function is enabled.
While this bit is set, a rising edge on the SYNC_IN pin causes
the device to advance the SYNC_CLK rising edge by one
REFCLK cycle. This bit does not self-clear.
CFR2<9>: CRYSTAL OUT Enable Bit
CFR2<9> = 0 (default). The CRYSTAL OUT pin is inactive.
CFR2<9> = 1. The CRYSTAL OUT pin is active. The crystal
oscillator circuitry output drives the CRYSTAL OUT pin, which
can be used as a reference frequency for additional devices.
CFR2<8>: Not Used, Leave Clear
CFR2<7:3>: Reference Clock Multiplier Control Bits
This 5-bit word controls the multiplier value out of the clockmultiplier (PLL) block. See the Clock Multiplier section for
more details.
Rev. B | Page 30 of 40
AD9954
CFR2<2>: VCO Range Control Bit
CFR2<2> = 0 (default), VCO operates between 100 MHz and
250 MHz.
CFR2<2> = 1, VCO operates between 250 MHz and 400 MHz.
CFR2<1:0>: Charge Pump Current Control Bits
These bits are used to control the current setting on the charge
pump. The default setting, CFR2<1:0>, sets the charge pump
current to the default value of 75 μA. For each bit added, 25 μA
of current is added to the charge pump current:
01 = 100 μA, 10 = 125 μA, and 11 = 150 μA.
OTHER REGISTER DESCRIPTIONS
Amplitude Scale Factor (ASF)
The ASF register stores the 2-bit auto ramp rate speed value and
the 14-bit amplitude scale factor used in the output shaped
keying (OSK) operation. In auto-OSK operation, ASF<15:14>
tells the OSK block how many amplitude steps to take for each
increment or decrement. ASF<13:0> sets the maximum value
achievable by the OSK internal multiplier. In manual OSK
mode, ASF<15:14> has no effect. ASF<13:0> provide the output
scale factor directly. If the OSK is disabled using CFR1<25>,
this register has no effect on device operation.
Amplitude Ramp Rate (ARR)
The ARR register stores the 8-bit amplitude ramp rate used in
the auto-OSK mode. See the Amplitude Control Options
section for details.
Frequency Tuning Word 0 (FTW0)
The frequency tuning word is a 32-bit register that controls the
rate of accumulation in the phase accumulator of the DDS core.
Its specific role is dependent on the device mode of operation.
Phase Offset Word (POW)
The phase offset word is a 14-bit register that stores a phase
offset value. See the Phase Offset Word Mux section for
additional details.
RAM Segment Control Words (RSCW0, RSCW1, RSCW2,
and RSCW3)
When linear sweep is disabled, Register 0x07, Register 0x08,
Register 0x09, and Register 0x0A act as the RAM segment
control words for each of the RAM segments. Each of the RAM
segment control words is comprised of a RAM segment address
ramp rate, a final address value, a beginning address value, a
RAM segment mode control, and a no-dwell bit. Note the
discontinuities of the address registers, since they may make
programming a little more challenging.
RAM Segment Address Ramp Rate, RSCW<39:24>
For RAM modes that step through address values, such as
ramping, this 16-bit word defines the number of SYNC_CLK
cycles the RAM controller dwells at each address. A value of 0 is
invalid. Any other value from 1 to 65,535 can be used.
RAM Segment Final Address RSCW<9:8>, RSCW<23:16>
This discontinuous 10-bit sequence defines the final address
value for the given RAM segment. The order in which the bits
are previously listed is MSB first: RSCW<9> is the MSB and
RSCW<16> is the LSB of the final address value.
RAM Segment Beginning Address RSCW<3:0>,
RSCW <15:10>
This discontinuous 10-bit sequence defines the final address
value for the given RAM segment. The order in which the bits
are previously listed is MSB first: RSCW<3> is the MSB and
RSCW<10> is the LSB of the final address value.
RAM Segment No-Dwell Bit RSCW<4>
This bit sets the no-dwell feature of sweeping profiles. In
profiles that sweep from a defined beginning to a defined end,
the RAM controller can either dwell at the final address until
the next profile is selected or, when this bit is set, the RAM
controller returns to the beginning address and dwells there
until the next profile is selected.
RAM Segment Mode Control RSCW<7:5>
Frequency Tuning Word 1 (FTW1)
This 3-bit sequence determines the RAM segment’s mode of
operation. There are only five possible RAM modes, so only
values of 0 to 4 are valid (see Table 7).
The frequency tuning word is a 32-bit register that sets the
upper frequency in a linear sweep operation.
Register 0x07 and Register 0x08 are multifunctional registers.
Negative and Positive Linear Sweep Control Word
(NLSCW and PLSCW)
When linear sweep bit is enabled, Register 0x07 provides the
negative linear sweep control word (NLSCW) and Register 0x08
provides the positive linear sweep control word (PLSCW). Each
of the linear sweep control words contains a 32-bit delta frequency
tuning word (FDFTW and RDFTW) and an 8-bit sweep ramp
rate word (FSRRW and RSRRW). See the Modes of Operation
section for more details.
Rev. B | Page 31 of 40
AD9954
LAYOUT CONSIDERATIONS
For the best performance, the following layout guidelines
should be observed. Always separate the analog power supply
(AVDD) and the digital power supply (DVDD), even if just
from two different voltage regulators driven by a common
supply. Likewise, the ground connections (AGND and DGND)
should be kept separate as far back to the source as possible (for
example, separate the ground planes on a localized board, even
if the grounds connect to a common point in the system).
Bypass capacitors should be placed as close to device pins as
possible. Usually a multitiered bypassing scheme consisting of a
small high frequency capacitor (100 pF) placed close to the
supply pin and progressively larger capacitors (0.1 μF and 10 μF)
further back to the actual supply source works best.
Rev. B | Page 32 of 40
AD9954
DETAILED PROGRAMMING EXAMPLES
SINGLE-TONE MODE
In this example, the part is programmed to output a 122 MHz
single-tone carrier, the device is clocked with a 20 MHz crystal
oscillator, and the clock multiplier is used to push the internal
system clock up to 400 MHz. Phase offsets are then added to
the carrier.
The programming steps include the following:
1. Write to Control Register 1 instructing the part to autoclear
the phase accumulator whenever the phase offset word
changes and issues an I/O update. Set Bit 13 in the CFR1
register. The address for CFR1 is 0; therefore, an instruction
byte of 0x00 is sent and 0x00 00 00 20 for data. Note that
users must write to all four bytes of the register.
2. Write to Control Register 2 setting the clock multiplier value
to 20, and the VCO range bit to its upper value. In CFR2,
Bit 7 to Bit 3 control the multiply value. To get a multiplied
value of 20 from 5 bits, the binary value is 10100. As
previously mentioned, also send Bit 2 to put the VCO into its
upper range (to get 400 MHz). Therefore, the instruction byte
is 0x01 and 0x00 00 A4 for data.
3. Calculate the tuning word to generate a 122 MHz output
from a 400 MSPS clock, load it into FTW0, and latch the
data written to the I/O buffers into their respective registers.
The frequency tuning word equation becomes (122 MHz/
400 MHz) × 232, which yields 0x4E 14 7A E1. Send the
Instruction Byte 0x04 and four data bytes of 0x4E 14 7A E1.
Issue an I/O update, which transfers the data into the part.
Whenever a phase change is desired, calculate and write the
phase offset word to the part and issue an I/O update. For
example, if the first value is 45°, the phase offset word is
(45/360) × 214, or in decimal, 2048. Therefore, write an
instruction byte of 0x05 and Data Byte 0x0800. When an
I/O update is issued, the phase accumulator clears, which
starts it from a known phase of 0°. It again accumulates at a
122 MHz rate, except now phase shifting each and every
sample by 45°.
LINEAR SWEEP MODE
In this example, the part is programmed to generate a chirp
from 61.53 MHz to 62.73 MHz. The chirp up is in 1.20 μs,
the chirp down is in 1.8 μs, and the chirp is made as finely
linearized as possible. Therefore, users must calculate and
program:
The last example programmed the clock multiplier; therefore,
start with a 400 MSPS clock. FTW0 is (61.53/400) × 232 or
0x27611340, and FTW1 is (62.73/400) × 232 or 0x2825AEE6.
To turn the linear sweep on, set CFR1<21>.
The PLSCW and NLSCW are five bytes wide: one byte for the
ramp rate and four bytes for the incremental frequency value.
To begin, calculate the ramp rate, and cover 1.2 MHz on both
sweeps. The ramp rate tells the part how many SYNC_CLK
cycles (for SYSCLK cycles) to send at each incremental value.
When the shortest time possible is spent at each incremental
frequency, the most linearized sweep is achieved; therefore, the part
should only spend one SYNC_CLK period at each incremental
frequency, which ensures that the smallest frequency steps possible
are taken. For a 400 MSPS SYSCLK, the result is a 100 MHz
SYNC_CLK rate or a 10 ns SYNC_CLK period. This means on the
finest resolution, 120 incremental steps squeeze into the rising
sweep (1.2 μs/10 ns) and 180 on the falling sweep (1.8 μs/10 ns).
For the rising delta frequency, a 1.2 MHz/120 steps is calculated,
which means each step is approximately 10 kHz for the rising
delta frequency and approximately 666.6666 Hz for the falling
delta frequency. The logic in the linear sweep block ensures that
FTW1 on a rising sweep or FTW0 on a falling sweep is not
exceeded. If the exact incremental tuning word is not achieved
using the 32-bit resolution, round up, not down, to ensure the
entire range during the sweep is covered. To calculate the rising
delta frequency word, simply calculate (10 K/400 M) × 232 =
0x0001A36F. Combining the rising ramp rate, first byte, and the
rising delta frequency, the second byte to fifth byte yields the
PLSCW: 0x010001A36F. Likewise, the NLSCW works out to
0x0100001BF4. Table 14 is a summary table of instruction and
data bytes to write to.
Table 14. Linear Sweep Example Write Instructions
Register
CFR1
FTW0
FTW1
NLSCW
RLSCW
Instruction Byte
0x00
0x04
0x06
0x07
0x08
Data Byte
0x00200000
0x27611340
0x2825AEE6
0x0100001BF4
0x010001A36F
RAM MODE
 FTW0 for 61.53 MHz (the start frequency)
 FTW1 for 62.73 MHz (the stop frequency)
 CFR1 to put the part into linear sweep mode
 The positive linear sweep control word (PLSCW), to make as
linearized a chirp in 1.20 μs
 The negative linear sweep control word (NLSCW), to make
as linearized a chirp in 1.80 μs
This example programs the RAM. Use the RAM on the AD9954
to simulate the nonlinear filter shape of a Gaussian filter response
on the FSK data. Begin by plotting the filter response from F0 to
F1 and from F1 to F0. The transition time specification (see
Table 1) tells how long it takes to transition from F0 to F1 and
from F1 to F0, either as an actual time value or as a fraction of
the symbol rate. Both ways show how long it can take to change
symbols, and for this application, it is 100 ns. To program the
RAM, decide how many RAM segments to use, program the
RAM segment control word for each of those segments, and
load the RAM data for each of those segments.
Rev. B | Page 33 of 40
AD9954
Because there is a ramp-up, but no ramp-down, RAM mode,
two RAM segments are generated; one for the transition from
F0 to F1, and one for the transition from F1 to F0. Step through
the intermediary frequencies as quickly as possible, because the
faster the steps, the less the output frequency deviates from the
ideal frequency response of the filter. The fastest the AD9954
can step through the values in the RAM is at the SYNC_CLK
rate, or ¼ of the SYSCLK rate, which works out to 10 ns,
assuming the maximum SYSCLK rate of 400 MSPS. Dividing
the total transition time of 100 ns by the time for each transition,
100 steps can be taken. The intermediary frequencies are solved
by looking at the instantaneous frequency on the curve every
10 ns and by recording that value. This gives 200 frequency
values, 100 representing the change from F0 to F1 and 100
representing the change from F1 to F0. This is the information
needed to program the RAM.
Begin by programming CFR1 to set the RAM enable bit.
Calculate and program RSCW0 and RSCW1. Each of the RAM
segment control words has an address ramp rate (16 bits), a
final address (10 bits), a beginning address (10 bits), a mode
control value (3 bits), and a no-dwell flag. Stepping through the
intermediary frequencies as quickly as possible was previously
discussed; therefore, the ramp rate for each word is 0x0000.
Define RAM Segment 0 to occupy the RAM space from
Address 0 to Address 99, which gives 100 values. Define RAM
Segment 1 to occupy Address 100 to Address 199 (also 100
values). Look at the modes of operation choice and recognize
that the ramp-up mode is used to step through each of the
addresses and then holds the final value in the profile.
Therefore, for each RSCW, the mode control bits are b’001.
Because staying at the last value is recommended, the no-dwell
bit is 0. To form the data for each RSCW, combine these values.
For RSCW0, it is 0x0100630020. For RSCW1, it is
0x0100C79021. Because the words that comprise the RSCW are
not contiguous, care must be taken in calculating the RSCW.
Make a chart of each of the subwords in order: address ramp
rate, final address, beginning address, mode, and no dwell.
Write the binary values for each subword, and then, with a copy
of the register map printed out, write each of the binary bits into the
map. When this is completed, the individual bytes can be read from
the map. For example, Table 15 shows how RSCW1 would appear.
Table 15. RAM Mode Register Table Settings
RAM
Segment
Control
Word
No. 1
(RSCW1)
(0x08)
<7:0>
<15:8>
<23:16>
<31:24>
<39:32>
NoRAM Segment 1
RAM
Dwell
Beginning
Segment 1
Mode Control Active Address <9:6>
0
0001
<2:0>
001
RAM Segment 1
RAM Segment 1
Beginning
Final Address <9:8>
Address <5:0>
00
100100
RAM Segment 1 Final Address <7:0>
11000111
RAM Segment 1 Address Ramp Rate
<15:8> 00000000
RAM Segment 1 Address Ramp Rate
<7:0> 00010000
The RSCW0 and RSCW1 values must be loaded into their
registers before attempting to write data to RSCW0 and
RSCW1; therefore, issue an I/O update.
The next step is to convert each of the intermediary frequencies
into a frequency tuning word according to
ftw 
fi
 2 32
SYSCLK
where:
fi is the desired intermediary frequency.
SYSCLK is the system clock rate.
Once this is complete, the result for each profile should be a
vector of 100 32-bit words. To write RAM Segment 0, select
Profile 0 (PS0 = 0, PS1 = 0), and then write the instruction byte
b’00001011, which indicates a RAM write operation is going to
be performed. The serial port I/O controller recognizes this and
polls the profile select pins, thus determining that Profile 0 is
the target storage location for the data out of RSCW0 previously
entered. It now knows to put the first word at Address 0, the last
word at Address 99, and that there are 100 words in total.
Proceed to load all 100 32-bit frequency words into the RAM.
When this is done, write the data to RAM Segment 1. First,
change to Profile 1 (PS0 = 1, PS1 = 0), and then write the RAM
instruction byte again. The device now knows to write the first
word at Address 100, the last word at Address 199, and again
that there are 100 words in total. Write all 100 32-bit words of
RAM Segment 1 and issue an I/O update. Whenever the PS0
pin is toggled (from 0 to 1), the part steps through the RAM
segment, which is the Gaussian-shaped pattern programmed
into the RAM.
Rev. B | Page 34 of 40
AD9954
SUGGESTED APPLICATION CIRCUITS
03374-012
AD9954
FREQUENCY
TUNING
WORD
MODULATED/
DEMODULATED
SIGNAL
RF/IF INPUT
LPF
REFCLK
PHASE
OFFSET
WORD 1
I/I-BAR
BASEBAND
REFCLK
CRYSTAL
Figure 31. Synchronized LO for Upconversion/Downconversion
AD9954 DDS
IOUT
IOUT
LPF
REFCLK
CRYSTAL OUT
SYNC_OUT
RF OUT
LOOP
FILTER
SYNC_IN
VCO
AD9954 DDS
AD9954
IOUT
LPF
REFCLK
03374-013
FILTER
IOUT
TUNING
WORD
FREQUENCY
TUNING
WORD
Figure 32. Digitally Programmable Divide-by-N Function in PLL
LPF
IOUT
LPF
AD9954 DDS
AD9954
03374-014
ON-CHIP
COMPARATOR
CMOS LEVEL CLOCK
Q/Q-BAR
BASEBAND
Figure 34. Two AD9954s Synchronized to Provide I and
Q Carriers with Independent Phase Offsets for Nulling
TUNING WORD
IOUT
PHASE
OFFSET
WORD 2
Figure 33. Frequency Agile Clock Generator
Rev. B | Page 35 of 40
03374-015
REF
SIGNAL
PHASE
COMPARATOR
Figure 35. Evaluation Board Channel 1
Rev. B | Page 36 of 40
C30
13pF
L1
39nH
C50
13pF
C31
27pF
L2
56nH
C52
6.8pF
R3
243Ω
C29
33pF
L3
68nH
C51
2.2pF
C35
39pF
3
C32
22pF
2
AVDD
7
AGND
8
OSC/REFCLK
9
OSC/REFCLK
10
CRYSTAL OUT
11
CLKMODESELECT
12
LOOP_FILTER
DVDD
DGND
AVDD
AGND
I/O UPDATE
GND
1
4
6
5
4
J2
FILTER_IN_DUT1
W1
PS1_DUT1
1
2
3
AVDD
R8
25Ω
AVDD
NOTES
1. THE FULL-SCALE DAC OUTPUT CURRENT IS CONTROLLED BY MEANS OF AN EXTERNAL
RESISTANCE (RSET ) CONNECTED BETWEEN THE DAC_R SET PIN AND GROUND. RESISTOR
VALUES FOR FULL-SCALE CURRENTS ARE: 3.92kΩ = 10mA, 5.23kΩ = 7.5mA, 7.87kΩ = 5.0mA,
15.8kΩ = 2.5mA.
2. C33 IS USED FOR A SIMULATED CAPACITANCE LOAD FOR THE COMPARATOR OUT. THE
CAPACITANCE VALUE SHOULD NOT EXCEED 10pF.
3. CAPACITORS C48 AND C49 SHOULD BE SOLDERED IN PLACE WHEN THE REF_CLK_DUT1
INPUT IS USED. CAPACITORS C35 AND C36 SHOULD BE SOLDERED IN PLACE WHEN
CRYSTAL ×1 IS USED IN CONJUNCTION WITH THE INTERNAL OSCILLATOR.
4. USE EITHER RESISTORS R4 AND R5 (COMPARATOR INPUTS) OR R6 AND R7 (FILTERED
OUTPUT) FOR THE IOUT AND IOUT. DO NOT USE BOTH SETS AT THE SAME TIME.
J1
AVDD
AVDD
GND
XTAL_DUT2
CLKMODESEL_DUT1
C36
39pF
GND
C34
0.01µF
C49
0.1µF
R1
50Ω
C48
0.1µF
×1 25MHz
XTAL_DUT2
J3
FILTER_OUT_DUT1
CRYSTAL OUT
DUT2
J4
REF_CLK_DUT1
4
1
T1
5
3
BALUN
NOTE 3
1
2
3
4
5
6
PS0_DUT1
OSK_DUT1
SYNCMULTI_DUT2
SYNCMULTI_DUT1
R6
0Ω
U7
AD9954
AGND
AGND
AVDD
AGND
DVDD
GND
AVDD
GND
DVDD_I/O
AVDD
NOTE 4
R4
0Ω
AVDD
FUD_DUT1
AVDD
AVDD
AVDD
GND
SDIO
SCLK
CSB_DUT1
SDO
GND
PS1 48
47
PS0
46
OSK
45
SYNC_CLK
44
SYNC_IN
43
DVDD_I/O
AVDD
13
14
15
16
17
18
GND
GND
AVDD
GND
I/O_SYNC_DUT1
42
41
40
39
38
37
DGND
SDIO
SCLK
CS
SDO
AVDD
IOUT
IOUT
AGND
DACBP
R9
25Ω
R5
0Ω
AVDD
AVDD
GND
AVDD
GND
AVDD
R10
3.92kΩ
GND
C7
0.1µF
GND
DVDD
C47
1µF
C6
0.1µF
C12
0.1µF
L4
18nH
C37
22pF
L8
20nH
C46
7.5pF
C11
0.1µF
GND
C4
0.1µF
L6
20nH
C39
7.5pF
C42
39pF
DVDD_I/O
C45
22pF
L7
18nH
C38
33pF
C5
0.1µF
C10
0.1µF
C44
39pF
L9
12nH
C41
22pF
L5
12nH
C40
39pF
J5
COMP_OUT_DUT1
C33
SEE
NOTE 2
R14
50Ω
PWRDWNCTRL_DUT1
DVDD
GND
GND
RESET_DUT1
NOTE 2
NOTE 1
R7
0Ω
RESET 36
35
PWRDWNCTL
34
DVDD
33
DGND
32
AGND
31
COMP_IN
30
COMP_IN
29
AVDD
28
COMP_OUT
27
AVDD
26
AGND
25
AVDD
IOSYNC
DAC_R SET
19
20
21
22
23
24
GND
C8
0.1µF
C9
0.1µF
C43
33pF
C3
0.1µF
C2
0.1µF
C1
0.1µF
03374-033
DUT 1
AD9954
EVALUATION BOARD SCHEMATICS
Rev. B | Page 37 of 40
Figure 36. Evaluation Board Channel 2
J6
C59
13pF
L10
39nH
C53
13pF
C61
0.01µF
C64
0.1µF
C57
27pF
L12
56nH
C60
6.8pF
CRYSTAL OUT
DUT2
J7
XTAL_DUT2
AVDD
R21
0Ω
R18
50Ω
C63
0.1µF
C56
33pF
L11
68nH
C54
2.2pF
3
C55
22pF
2
AVDD
7
AGND
8
OSC/REFCLK
9
OSC/REFCLK
10
CRYSTAL OUT
11
CLKMODESELECT
12
LOOP_FILTER
4
GND
1
6
5
4
J14
FILTER_IN_DUT2
W3
XTAL_OUT
R16
243Ω
XTAL_OUT
CLKMODESEL_DUT2
AVDD
GND
1
2
3
AVDD
AVDD
NOTES
1. THE FULL-SCALE DAC OUTPUT CURRENT IS CONTROLLED BY MEANS OF AN EXTERNAL
RESISTANCE (RSET ) CONNECTED BETWEEN THE DAC_R SET PIN AND GROUND. RESISTOR
VALUES FOR FULL-SCALE CURRENTS ARE: 3.92kΩ = 10mA, 5.23kΩ = 7.5mA, 7.87kΩ = 5.0mA,
15.8kΩ = 2.5mA.
2. C58 IS USED FOR A SIMULATED CAPACITANCE LOAD FOR THE COMPARATOR OUT. THE
CAPACITANCE VALUE SHOULD NOT EXCEED 10pF.
3. FOR CRYSTAL OUT CLOCK OPERATION REMOVE T4, TERMINATE THE OSC/REFCLK TO
EITHER AVDD (R30) OR GND (R31) AND SOLDER R21 IN PLACE. DO NOT USE R30 OR R31
SIMULTANEOUSLY.
J12
FILTER_IOUT_DUT2
REF_CLK_DUT2
4
1
T4
5
3
BALUN
GND
AVDD
AVDD
NOTE 3
PS1_DUT2
I/O UPDATE
DVDD
DGND
AVDD
AGND
PS0_DUT2
OSK_DUT2
SYNCMULTI_DUT1
SYNCMULTI_DUT2
U8
AD9954
AGND
AGND
AVDD
AGND
R22
25Ω
GND
GND
AVDD
GND
R31
0Ω
1
2
3
4
5
6
DVDD_I/O
AVDD
13
14
15
16
17
18
AVDD
DVDD
GND
AVDD
GND
AVDD
FUD_DUT2
CSB_DUT2
SDO
GND
R30
0Ω
GND
SDIO
SCLK
AVDD
IOUT
IOUT
R9
25Ω
NOTE 1
AVDD
GND
J9
AVDD
R2
3.3kΩ
R25
10kΩ
C13
0.1µF
GND
DVDD
C14
0.1µF
J11
C15
0.1µF
C24
0.1µF
J10
COMP_IN
C65
0.1µF
C16
0.1µF
C18
0.1µF
C17
0.1µF
C19
0.1µF
RB_ENABLE
SDIO
SDO
SCLK
CS_DUT2
RESET_DUT2
CLKMODESEL_DUT2
PWRDWNCTRL_DUT2
I/O_SYNC_DUT2
FUD_DUT2
OSK_DUT2
PS1_DUT2
PS0_DUT2
C23
0.1µF
GND
DVDD_I/O
COMP_OUT_DUT2
C66
0.1µF
AVDD
R11
3.3kΩ
R24
10kΩ
GND
C22
0.1µF
C58
SEE NOTE 2
GND
AVDD
C62
1µF
NOTE 2
AVDD
AVDD
GND
AVDD
PWRDWNCTRL_DUT2
DVDD
GND
GND
GND
RESET_DUT2
R15
3.92kΩ
RESET 36
35
PWRDWNCTL
34
DVDD
33
DGND
32
AGND
31
COMP_IN
30
COMP_IN
29
AVDD
28
COMP_OUT
27
AVDD
26
AGND
25
AVDD
IOSYNC
DAC_R SET
AVDD
I/O_SYNC_DUT2
PS1 48
47
PS0
46
OSK
45
SYNC_CLK
44
SYNC_IN
43
DVDD_I/O
42
DGND
41
SDIO
40
SCLK
39
CS
38
SDO
37
AGND
DACBP
19
20
21
22
23
24
CS_DUT1
RESET_DUT1
CLKMODESEL_DUT1
PWRDWNCTRL_DUT1
I/O_SYNC_DUT1
FUD_DUT1
OSK_DUT1
PS1_DUT1
PS0_DUT1
COMP_IN
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P25
C20
0.1µF
U13
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
C21
0.1µF
P50
P49
P48
P47
P46
P45
P44
P43
P42
P41
P40
P39
P38
P37
P36
P35
P34
P33
P32
P31
P30
P29
P28
P27
P26
GND
03374-034
DUT 2
AD9954
Figure 37. Evaluation Board Interface Logic
Rev. B | Page 38 of 40
U4
C36CRPX
CLOCK F C3
B7
B5
B4
CLOCK A C1
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
C2
B3
33
34
35
CLOCK D C0
A0
A1
A2
A3
A4
A5
A6
A7
B6
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
1
2
3
4
5
6
7
8
9
1
U12
2
R36
10kΩ
11
U12
4
10
8
74LVC14A
9
U12
SDI
U12
6
5
9
U6
74LVC125A
8
10
74LVC125A
6
4
U6
U6 1
74LVC125A
2
3
PS0_DUT1
PS1_DUT1
PS0_DUT2
PS1_DUT2
OSK_DUT1
OSK_DUT2
FUD_DUT1
FUD_DUT2
GND : 10
VCC : 20
12
13
14
15
16
17
18
19
74LVC14A
5
9
8D
8
7
6
5
4
3
2
1D
74LVC574A
U11
1 EN
11 C1
74LVC14A
3
74LVC14A
U12
VCC
RB_ENABLE
R37
10kΩ
VCC
GND
R35
10kΩ
VCC
SCLK1
74LVC14A
VCC
R34
10kΩ
SDO
SDIO
9
8D
8
7
6
5
4
3
2
1D
74LVC574A
U10
1 EN
11 C1
12
13
14
15
16
17
18
19
I/O_SYNC_DUT1
I/O_SYNC_DUT2
PWRDWNCTRL_DUT1
PWRDWNCTRL_DUT2
CLKMODESEL_DUT1
CLKMODESEL_DUT2
RESET_DUT1
RESET_DUT2
GND : 10
VCC : 20
GND
VCC
C72
0.1µF
GND
DVDD_I/O
GND
AVDD
C71
0.1µF
C26
10µF
C25
10µF
9
8D
8
7
6
5
4
3
2
1D
74LVC574A
U9
1 EN
11 C1
C70
0.1µF
C69
0.1µF
GND
VCC
GND
DVDD
SDI
SCLK
CSB_DUT1
CSB_DUT2
REF_CLK
GND : 10
VCC : 20
12
13
14
15
16
17
18
19
GND
VCC
C68
0.1µF
C28
10µF
C27
10µF
J15
R32
0Ω
DVDD
AVDD
DVDD_I/O
GND
VCC
DIGITAL LOGIC
REF CLK
SCLK1
TB5
U3
5
4
3
2
1
03374-035
W2
AD9954
AD9954
OUTLINE DIMENSIONS
9.00
BSC SQ
1.20
MAX
BOTTOM VIEW
(PINS UP)
37
36
48
1
37
36
48
1
7.00
BSC SQ
PIN 1
3.50
SQ
TOP VIEW
(PINS DOWN)
0° MIN
1.05
1.00
0.95
0.15
0.05
SEATING
PLANE
0.20
0.09
7°
3.5°
0°
0.08 MAX
COPLANARITY
EXPOSED
PAD
12
13
VIEW A
25
24
25
24
0.50 BSC
LEAD PITCH
VIEW A
ROTATED 90° CCW
12
13
0.27
0.22
0.17 FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MS-026-ABC
011708-A
0.75
0.60
0.45
Figure 38. 48-Lead Thin Quad Flat Package, Exposed Pad [TQFP_EP]
(SV-48-4)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD9954YSV
AD9954YSV-REEL7
AD9954YSVZ1
AD9954YSVZ-REEL71
AD9954/PCBZ1
1
Temperature
Range
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
Package Description
48-Lead Thin Quad Flat Package, Exposed Pad [TQFP_EP]
48-Lead Thin Quad Flat Package, Exposed Pad [TQFP_EP]
48-Lead Thin Quad Flat Package, Exposed Pad [TQFP_EP]
48-Lead Thin Quad Flat Package, Exposed Pad [TQFP_EP]
Evaluation Board
Z = RoHS Compliant Part.
Rev. B | Page 39 of 40
Ordering
Quantity
500
500
Package
Option
SV-48-4
SV-48-4
SV-48-4
SV-48-4
AD9954
NOTES
©2003–2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D03374-0-5/09(B)
Rev. B | Page 40 of 40