MAXIM MAX4041EUA

19-1377; Rev 0; 5/98
Single/Dual/Quad, Low-Cost, SOT23,
Micropower Rail-to-Rail I/O Op Amps
____________________________Features
♦ Single-Supply Operation Down to +2.4V
These amplifiers have outputs that typically swing to
within 10mV of the rails with a 100kΩ load. Rail-to-rail
input and output characteristics allow the full powersupply voltage to be used for signal range. The combination of low input offset voltage, low input bias current,
and high open-loop gain makes them suitable for lowpower/low-voltage precision applications.
The MAX4040 is offered in a space-saving 5-pin SOT23
package. All specifications are guaranteed over the
-40°C to +85°C extended temperature range.
________________________Applications
Battery-Powered
Systems
Portable/Battery-Powered
Electronic Equipment
Digital Scales
Strain Gauges
Sensor Amplifiers
Cellular Phones
Notebook Computers
PDAs
♦ Ultra-Low Power Consumption:
10µA Supply Current per Amplifier
1µA Shutdown Mode (MAX4041/MAX4043)
♦ Rail-to-Rail Input Common-Mode Range
♦ Outputs Swing Rail-to-Rail
♦ No Phase Reversal for Overdriven Inputs
♦ 200µV Input Offset Voltage
♦ Unity-Gain Stable for Capacitive Loads up to 200pF
♦ 90kHz Gain-Bandwidth Product
♦ Available in Space-Saving 5-Pin SOT23 and
8-Pin µMAX Packages
Ordering Information
PART
TEMP. RANGE
PINSOT
PACKAGE TOP MARK
MAX4040EUK-T
-40°C to +85°C
5 SOT23-5
MAX4040EUA
MAX4040ESA
MAX4041ESA
MAX4041EUA
MAX4042EUA
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
8 µMAX
8 SO
8 SO
8 µMAX
8 µMAX
—
—
—
—
—
MAX4042ESA
-40°C to +85°C
8 SO
—
MAX4043EUB
-40°C to +85°C
10 µMAX
—
MAX4043ESD
MAX4044ESD
-40°C to +85°C
-40°C to +85°C
14 SO
14 SO
—
—
Selector Guide
PART
NO. OF
AMPS
SHUTDOWN
MAX4040
1
—
5-pin SOT23,
8-pin µMAX/SO
MAX4041
1
Yes
8-pin µMAX/SO
MAX4042
2
—
8-pin µMAX/SO
MAX4043
2
Yes
MAX4044
4
—
PIN-PACKAGE
10-pin µMAX/
14-pin SO
14-pin SO
Rail-to-Rail is a registered trademark of Nippon Motorola Ltd.
ACGF
Pin Configurations
TOP VIEW
OUT
1
VEE 2
IN+ 3
5
VCC
4
IN-
MAX4040
SOT23-5
Pin Configurations continued at end of data sheet.
________________________________________________________________ Maxim Integrated Products
1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.
For small orders, phone 408-737-7600 ext. 3468.
MAX4040–MAX4044
________________General Description
The MAX4040–MAX4044 family of micropower op amps
operates from a single +2.4V to +5.5V supply or dual
±1.2V to ±2.75V supplies and have Rail-to-Rail® input
and output capabilities. These amplifiers provide a
90kHz gain-bandwidth product while using only 10µA of
supply current per amplifier. The MAX4041/MAX4043
have a low-power shutdown mode that reduces supply
current to less than 1µA and forces the output into a
high-impedance state. The combination of low-voltage
operation, rail-to-rail inputs and outputs, and ultra-low
power consumption makes these devices ideal for any
portable/battery-powered system.
MAX4040–MAX4044
Single/Dual/Quad, Low-Cost, SOT23,
Micropower, Rail-to-Rail I/O Op Amps
ABSOLUTE MAXIMUM RATINGS
Supply Voltage (VCC to VEE)..................................................+6V
All Other Pins ...................................(VCC + 0.3V) to (VEE - 0.3V)
Output Short-Circuit Duration to VCC or VEE ..............Continuous
Continuous Power Dissipation (TA = +70°C)
5-Pin SOT23 (derate 7.1mW/°C above +70°C).............571mW
8-Pin µMAX (derate 4.1mW/°C above +70°C) ..............330mW
8-Pin SO (derate 5.88mW/°C above +70°C).................471mW
10-Pin µMAX (derate 5.6mW/°C above +70°C) ...........444mW
14-Pin SO (derate 8.33mW/°C above +70°C)..............667mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +160°C
Lead Temperature (soldering, 10sec) .............................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—TA = +25°C
(VCC = +5.0V, VEE = 0, VCM = 0, VOUT = VCC / 2, SHDN = VCC, RL = 100kΩ tied to VCC / 2, unless otherwise noted.)
PARAMETER
SYMBOL
Supply-Voltage Range
VCC
Supply Current
per Amplifier
ICC
Shutdown Supply
Current per Amplifier
ICC(SHDN)
Input Offset Voltage
VOS
Input Bias Current
Input Offset Current
Differential Input
Resistance
Input Common-Mode
Voltage Range
CONDITIONS
MIN
Inferred from PSRR test
TYP
2.4
VCC = 2.4V
10
VCC = 5.0V
14
SHDN = VEE, MAX4041
and MAX4043 only
VEE ≤ VCM ≤ VCC
20
2.0
5.0
MAX4044ESD
±0.20
±2.0
MAX404_EU_
±0.25
±2.5
All other packages
±0.20
±1.50
mV
nA
IB
VEE ≤ VCM ≤ VCC
±2
±10
IOS
VEE ≤ VCM ≤ VCC
±0.5
±3.0
RIN(DIFF)
VCM
µA
mV
nA
VIN+ - VIN- < 1.0V
45
MΩ
VIN+ - VIN- > 2.5V
4.4
kΩ
Inferred from the CMRR test
VEE
VCC
MAX404_EU_
65
94
All other packages
70
94
75
85
Power-Supply
Rejection Ratio
PSRR
2.4V ≤ VCC ≤ 5.5V
Large-Signal
Voltage Gain
AVOL
(VEE + 0.2V) ≤ VOUT ≤ (VCC - 0.2V)
Output Voltage
Swing High
VOH
Specified as VCC - VOH
RL = 100kΩ
10
RL = 25kΩ
60
Output Voltage
Swing Low
VOL
Specified as VEE - VOL
RL = 100kΩ
10
RL = 25kΩ
40
IOUT(SC)
µA
VCC = 5.0V
VEE ≤ VCM ≤ VCC
2
V
1.0
CMRR
Channel-to-Channel
Isolation
UNITS
5.5
VCC = 2.4V
Common-Mode
Rejection Ratio
Output Short-Circuit
Current
MAX
RL = 100kΩ
RL = 25kΩ
dB
dB
94
74
dB
85
Sourcing
0.7
Sinking
2.5
Specified at DC, MAX4042/MAX4043/MAX4044 only
80
_______________________________________________________________________________________
V
90
60
mV
mV
mA
dB
Single/Dual/Quad, Low-Cost, SOT23,
Micropower, Rail-to-Rail I/O Op Amps
(VCC = +5.0V, VEE = 0, VCM = 0, VOUT = VCC / 2, SHDN = VCC, RL = 100kΩ tied to VCC / 2, unless otherwise noted.)
PARAMETER
SYMBOL
Output Leakage Current in
Shutdown
IOUT(SHDN)
CONDITIONS
MIN
SHDN = VEE = 0, MAX4041/MAX4043 only
(Note 1)
TYP
MAX
UNITS
20
100
nA
SHDN Logic Low
VIL
MAX4041/MAX4043 only
SHDN Logic High
VIH
MAX4041/MAX4043 only
SHDN Input Bias Current
IIH, IIL
MAX4041/MAX4043 only
Gain Bandwidth Product
GBW
90
kHz
Phase Margin
Φm
68
degrees
Gain Margin
Gm
18
dB
Slew Rate
SR
40
V/ms
Input Voltage Noise Density
en
f = 1kHz
70
nV/√Hz
Input Current Noise Density
in
f = 1kHz
0.05
pA/√Hz
AVCL = +1V/V, no sustained oscillations
200
pF
200
µs
Capacitive-Load Stability
0.3 x VCC
V
0.7 x VCC
V
40
120
nA
Power-Up Time
tON
Shutdown Time
tSHDN
MAX4041 and MAX4043 only
50
µs
tEN
MAX4041 and MAX4043 only
150
µs
3
pF
fIN = 1kHz, VOUT = 2Vp-p, AV = +1V/V
0.05
%
50
µs
Enable Time from Shutdown
Input Capacitance
CIN
Total Harmonic Distortion
THD
Settling Time to 0.01%
tS
AV = +1V/V, VOUT = 2VSTEP
ELECTRICAL CHARACTERISTICS—TA = TMIN to TMAX
(VCC = +5.0V, VEE = 0, VCM = 0, VOUT = VCC / 2, SHDN = VCC, RL = 100kΩ tied to VCC / 2, unless otherwise noted.) (Note 2)
PARAMETER
SYMBOL
Supply-Voltage Range
VCC
Supply Current
per Amplifier
ICC
Shutdown Supply
Current per Amplifier
ICC(SHDN)
Input Offset Voltage
VOS
CONDITIONS
Inferred from PSRR test
MIN
TYP
2.4
SHDN = VEE, MAX4041 and MAX4043 only
VEE ≤ VCM ≤ VCC
Input Bias Current
Input Offset Current
TCVOS
UNITS
5.5
V
28
µA
6.0
µA
MAX4044ESA
±4.5
MAX404_EU_
±5.0
All other packages
Input Offset Voltage Drift
MAX
mV
±3.5
2
µV/°C
IB
VEE ≤ VCM ≤ VCC
±20
nA
IOS
VEE ≤ VCM ≤ VCC
±8
nA
_______________________________________________________________________________________
3
MAX4040–MAX4044
ELECTRICAL CHARACTERISTICS—TA = +25°C (continued)
ELECTRICAL CHARACTERISTICS—TA = TMIN to TMAX (continued)
(VCC = +5.0V, VEE = 0, VCM = 0, VOUT = VCC / 2, SHDN = VCC, RL = 100kΩ tied to VCC / 2, unless otherwise noted.) (Note 2)
PARAMETER
SYMBOL
Input Common-Mode
Voltage Range
CONDITIONS
VCM
MIN
Inferred from the CMRR test
TYP
VEE
MAX404_EU_
60
All other packages
65
MAX
UNITS
VCC
V
Common-Mode
Rejection Ratio
CMRR
VEE ≤ VCM ≤ VCC
Power-Supply
Rejection Ratio
PSRR
2.4V ≤ VCC ≤ 5.5V
70
dB
Large-Signal Voltage
Gain
AVOL
(VEE + 0.2V) ≤ VOUT ≤ (VCC - 0.2V), RL = 25kΩ
68
dB
Output Voltage Swing
High
VOH
Specified as VCC - VOH, RL = 25kΩ
125
mV
Output Voltage Swing
Low
VOL
Specified as VEE - VOL, RL = 25kΩ
75
mV
dB
Note 1: Tested for VEE ≤ VOUT ≤ VCC. Does not include current through external feedback network.
Note 2: All devices are 100% tested at TA = +25°C. All temperature limits are guaranteed by design.
__________________________________________Typical Operating Characteristics
(VCC = +5.0V, VEE = 0, VCM = VCC / 2, SHDN = VCC, RL = 100kΩ to VCC / 2, TA = +25°C, unless otherwise noted.)
MAX4041/MAX4043
SHUTDOWN SUPPLY CURRENT
PER AMPLIFIER vs. TEMPERATURE
SUPPLY CURRENT PER AMPLIFIER
vs. TEMPERATURE
VCC = +5.5V
14
12
10
VCC = +2.4V
8
6
4
MAX4040/44-01.5
16
5
SHUTDOWN SUPPLY CURRENT (µA)
MAX4040/44-01
20
18
SUPPLY CURRENT (µA)
MAX4040–MAX4044
Single/Dual/Quad, Low-Cost, SOT23,
Micropower, Rail-to-Rail I/O Op Amps
SHDN = 0
4
3
VCC = +5.5V
2
VCC = +2.4V
1
2
0
0
-60
-40
-20
0
20
40
TEMPERATURE (°C)
4
60
80
100
-60 -40
-20
0
20
40
60
TEMPERATURE (°C)
_______________________________________________________________________________________
80
100
Single/Dual/Quad, Low-Cost, SOT23,
Micropower, Rail-to-Rail I/O Op Amps
VCM = 0
VCC = +2.4V
100
0
VCC = +5.5V
-2
0
-2.5
-3
-5.0
-4
-40
-20
40
20
0
60
80
100
-60
TEMPERATURE (°C)
-40
-20
0
20
40
60
120
RL TO VEE
100
VOLTAGE FROM VCC (mV)
IBIAS (nA)
2.5
0
-2.5
-5.0
60
3.5
40
5.5
4.5
VCC = +5.5V, RL = 100kΩ
VCC = +2.4V, RL = 100kΩ
0
20
40
60
80
60
VCC = +5.5V, RL = 20kΩ
40
VCC = +2.4V, RL = 10kΩ
VCC = +5.5V, RL = 100kΩ
20
VCC = +2.4V, RL = 100kΩ
-20
0
20
40
TEMPERATURE (°C)
100
MAX4040/44-09
-80
COMMON-MODE REJECTION (dB)
MAX4040/44-08
COMMON-MODE REJECTION
vs. TEMPERATURE
80
-40
-20
OUTPUT SWING LOW
vs. TEMPERATURE
100
-60
-40
TEMPERATURE (°C)
RL TO VCC
0
-60
VCM (V)
120
2.2
VCC = +5.5V, RL = 20kΩ
0
2.5
1.8
VCC = +2.4V, RL = 10kΩ
80
20
1.5
1.4
OUTPUT SWING HIGH
vs. TEMPERATURE
MAX4040/44-06
VCC = +5.5V
1.0
VCM (V)
TEMPERATURE (°C)
5.0
0 0.5
0.6
0 0.2
100
80
INPUT BIAS CURRENT vs.
COMMON-MODE VOLTAGE (VCC = 5.5V)
VOLTAGE FROM VEE (mV)
-60
MAX4040/44-07
200
VCC = +2.4V
2.5
-1
IBIAS (nA)
INPUT BIAS CURRENT (nA)
300
5.0
MAX4040/44-04
0
MAX4040/44-03
400
INPUT OFFSET VOLTAGE (µV)
INPUT BIAS CURRENT vs.
COMMON-MODE VOLTAGE (VCC = 2.4V)
INPUT BIAS CURRENT
vs. TEMPERATURE
MAX4040/44-5
INPUT OFFSET VOLTAGE
vs. TEMPERATURE
-85
VCC = +2.4V
-90
VCC = +5.5V
-95
-100
60
80
100
-60
-40
-20
0
20
40
60
80
100
TEMPERATURE (°C)
_______________________________________________________________________________________
5
MAX4040–MAX4044
Typical Operating Characteristics (continued)
(VCC = +5.0V, VEE = 0, VCM = VCC / 2, SHDN = VCC, RL = 100kΩ to VCC / 2, TA = +25°C, unless otherwise noted.)
____________________________________Typical Operating Characteristics (continued)
(VCC = +5.0V, VEE = 0, VCM = VCC / 2, SHDN = VCC, RL = 100kΩ to VCC / 2, TA = +25°C, unless otherwise noted.)
RL = 100kΩ
80
80
70
60
100
RL = 10kΩ
70
60
60
40
40
50
30
100
300
200
40
500
400
0
100
300
200
500
400
0
100
200
300
∆VOUT (mV)
∆VOUT (mV)
∆VOUT (mV)
OPEN-LOOP GAIN vs. OUTPUT SWING HIGH
(VCC = +5.5V, RL TIED TO VEE)
OPEN-LOOP GAIN
vs. TEMPERATURE
OPEN-LOOP GAIN
vs. TEMPERATURE
105
VCC = +5.5V, RL = 20kΩ TO VEE
100
70
95
90
VCC = +5.5V, RL = 20kΩ TO VCC
VCC = +2.4V, RL = 10kΩ TO VEE
80
50
75
40
100
200
300
VCC = +2.4V, RL TO VCC
70
-40
∆VOUT (mV)
-20
0
20
40
60
80
-60
100
-40
-20
MAX4040/44-16
60
AV = +1000V/V
50
20
0
40
GAIN AND PHASE vs. FREQUENCY
(CL = 100pF)
180
MAX4040/44-17
60
AV = +1000V/V
180
40
108
30
72
30
72
20
36
10
0
0
-36
-10
-72
GAIN (dB)
50
108
PHASE (DEGREES)
144
40
144
20
36
10
0
0
-36
-10
-72
-20
-108
-20
-108
-30
-144
-30
-144
-180
-40
-40
10
100
1k
10k
FREQUENCY (Hz)
100k
60
TEMPERATURE (°C)
TEMPERATURE (°C)
GAIN AND PHASE vs. FREQUENCY
(NO LOAD)
GAIN (dB)
VCC = +2.4V, RL TO VEE
75
VCC = +2.4V, RL = 10kΩ TO VCC
-60
400
90
80
70
0
VCC = +5.5V, RL TO VCC
95
85
85
60
VCC = +5.5V, RL TO VEE
100
-180
10
100
1k
10k
100k
FREQUENCY (Hz)
_______________________________________________________________________________________
PHASE (DEGREES)
RL = 20kΩ
80
105
GAIN (dB)
GAIN (dB)
90
400
110
MAX4040/44-14
RL = 100kΩ
100
110
MAX4040/44-13
110
6
70
50
0
RL = 20kΩ
80
50
30
RL = 100kΩ
90
GAIN (dB)
RL = 10kΩ
GAIN (dB)
GAIN (dB)
RL = 100kΩ
90
110
MAX4040/44-12
90
OPEN-LOOP GAIN vs. OUTPUT SWING LOW
(VCC = +5.5V, RL TIED TO VCC)
MAX4040/44-11
100
MAX4040/44-10
100
OPEN-LOOP GAIN vs. OUTPUT SWING HIGH
(VCC = +2.4V, RL TIED TO VEE)
MAX4040/44-15
OPEN-LOOP GAIN vs. OUTPUT SWING LOW
(VCC = +2.4V, RL TIED TO VCC)
GAIN (dB)
MAX4040–MAX4044
Single/Dual/Quad, Low-Cost, SOT23,
Micropower, Rail-to-Rail I/O Op Amps
80
100
Single/Dual/Quad, Low-Cost, SOT23,
Micropower, Rail-to-Rail I/O Op Amps
MAX4042/MAX4043/MAX4044
CROSSTALK vs. FREQUENCY
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. FREQUENCY
THD + NOISE (%)
-70
-80
-90
MAX4040/44-19
RL = 10kΩ
GAIN (dB)
1
MAX4040/44-18
-60
0.1
-100
RL = 100kΩ
RL = 10kΩ
-110
0.01
100
10
1k
10k
1
100
1000
FREQUENCY (Hz)
LOAD RESISTOR vs.
CAPACITIVE LOAD
SMALL-SIGNAL TRANSIENT RESPONSE
(NONINVERTING)
MAX4040/44-21
MAX4040/44-20
1000
10%
OVERSHOOT
RLOAD (kΩ)
10
FREQUENCY (Hz)
100mV
IN
REGION OF
MARGINAL STABILITY
0V
50mV/div
100
100mV
OUT
REGION OF
STABLE OPERATION
0V
10
0
250
500
750
10µs/div
1000
CLOAD (pF)
SMALL-SIGNAL TRANSIENT RESPONSE
(INVERTING)
LARGE-SIGNAL TRANSIENT RESPONSE
(NONINVERTING)
LARGE-SIGNAL TRANSIENT RESPONSE
(INVERTING)
MAX4040/44-22
MAX4040/42/44-23
MAX4040/42/44-24
4.5V
100mV
IN
IN
IN
0.5V
0V
50mV/div
4.5V
100mV
OUT
+2V
OUT
0.5V
0V
10µs/div
-2V
2V/div
2V/div
OUT
+2V
100µs/div
-2V
100µs/div
_______________________________________________________________________________________
7
MAX4040–MAX4044
____________________________________Typical Operating Characteristics (continued)
(VCC = +5.0V, VEE = 0, VCM = VCC / 2, SHDN = VCC, RL = 100kΩ to VCC / 2, TA = +25°C, unless otherwise noted.)
MAX4040–MAX4044
Single/Dual/Quad, Low-Cost, SOT23,
Micropower, Rail-to-Rail I/O Op Amps
______________________________________________________________Pin Description
PIN
MAX4040
SOT23-5 SO/µMAX
MAX4041
MAX4042
MAX4043
µMAX
SO
NAME
FUNCTION
1
6
6
—
—
—
—
OUT
Amplifier Output. High impedance
when in shutdown mode.
2
4
4
4
4
4
11
VEE
Negative Supply. Tie to ground for
single-supply operation.
3
3
3
—
—
—
—
IN+
Noninverting Input
4
2
2
—
—
—
—
IN-
Inverting Input
5
7
7
8
10
14
4
VCC
Positive Supply
—
N.C.
No Connection. Not internally connected.
—
1, 5, 8
1, 5
—
—
5, 7,
8, 10
—
—
8
—
—
—
—
SHDN
Shutdown Input. Drive high, or tie to
VCC for normal operation. Drive to VEE
to place device in shutdown mode.
—
—
—
1, 7
1, 9
1, 13
1, 7
OUTA,
OUTB
Outputs for Amplifiers A and B. High
impedance when in shutdown mode.
—
—
—
2, 6
2, 8
2, 12
2, 6
INA-,
INB-
Inverting Inputs to Amplifiers A and B
—
—
—
3, 5
3, 7
3, 11
3, 5
INA+,
INB+
Noninverting Inputs to Amplifiers A
and B
—
—
—
—
5, 6
6, 9
—
SHDNA,
SHDNB
Shutdown Inputs for Amplifiers A
and B. Drive high, or tie to VCC for
normal operation. Drive to VEE to
place device in shutdown mode.
—
—
—
—
—
—
8, 14
OUTC,
OUTD
Outputs for Amplifiers C and D
—
—
—
—
—
—
9, 13
INC-,
IND-
Inverting Inputs to Amplifiers C and D
—
—
—
—
—
—
10, 12
INC+,
IND+
Noninverting Inputs to Amplifiers C
and D
_______________Detailed Description
Rail-to-Rail Input Stage
The MAX4040–MAX4044 have rail-to-rail inputs and
rail-to-rail output stages that are specifically designed
for low-voltage, single-supply operation. The input
stage consists of separate NPN and PNP differential
stages, which operate together to provide a commonmode range extending to both supply rails. The
crossover region of these two pairs occurs halfway
between VCC and VEE. The input offset voltage is typically 200µV. Low operating supply voltage, low supply
current, rail-to-rail common-mode input range, and railto-rail outputs make this family of operational amplifiers
8
MAX4044
an excellent choice for precision or general-purpose,
low-voltage battery-powered systems.
Since the input stage consists of NPN and PNP pairs,
the input bias current changes polarity as the commonmode voltage passes through the crossover region.
Match the effective impedance seen by each input to
reduce the offset error caused by input bias currents
flowing through external source impedances (Figures
1a and 1b). The combination of high source impedance
plus input capacitance (amplifier input capacitance
plus stray capacitance) creates a parasitic pole that
produces an underdamped signal response. Reducing
input capacitance or placing a small capacitor across
the feedback resistor improves response in this case.
_______________________________________________________________________________________
Single/Dual/Quad, Low-Cost, SOT23,
Micropower, Rail-to-Rail I/O Op Amps
R3
R3 = R1
R2
R1
R2
Rail-to-Rail Output Stage
Figure 1a. Minimizing Offset Error Due to Input Bias Current
(Noninverting)
MAX4040–
MAX4044
The MAX4040–MAX4044 output stage can drive up to a
25kΩ load and still swing to within 60mV of the rails.
Figure 3 shows the output voltage swing of a MAX4040
configured as a unity-gain buffer, powered from a single
+4.0V supply voltage. The output for this setup typically
swings from (VEE + 10mV) to (VCC - 10mV) with a 100kΩ
load.
Applications Information
R3
Power-Supply Considerations
R3 = R1
R2
VIN
R1
R2
The MAX4040–MAX4044 operate from a single +2.4V to
+5.5V supply (or dual ±1.2V to ±2.75V supplies) and
consume only 10µA of supply current per amplifier. A
high power-supply rejection ratio of 85dB allows the
amplifiers to be powered directly off a decaying battery
voltage, simplifying design and extending battery life.
Power-Up Settling Time
Figure 1b. Minimizing Offset Error Due to Input Bias Current
(Inverting)
The MAX4040–MAX4044 typically require 200µs to
power up after VCC is stable. During this start-up time,
the output is indeterminant. The application circuit
should allow for this initial delay.
IN+
2.2k
IN2.2k
Figure 2. Input Protection Circuit
_______________________________________________________________________________________
9
MAX4040–MAX4044
MAX4040–
MAX4044
VIN
The MAX4040–MAX4044 family’s inputs are protected
from large differential input voltages by internal 2.2kΩ
series resistors and back-to-back triple-diode stacks
across the inputs (Figure 2). For differential input voltages (much less than 1.8V), input resistance is typically
45MΩ. For differential input voltages greater than 1.8V,
input resistance is around 4.4kΩ, and the input bias
current can be approximated by the following equation:
IBIAS = (VDIFF - 1.8V) / 4.4kΩ
In the region where the differential input voltage
approaches 1.8V, the input resistance decreases exponentially from 45MΩ to 4.4kΩ as the diode block begins
conducting. Conversely, the bias current increases with
the same curve.
MAX4040-44 fig04
MAX4040-44 fig03
1V/div
VIN = 2V
RL = 100kΩ TIED TO VEE
RL = 100kΩ TIED TO VEE
VIN = 4.0V
fIN = 1kHz
OUT
SHDN
5V/div
1V/div
IN
1V/div
OUT
200µs/div
200µs/div
Figure 4. Shutdown Enable/Disable Output Voltage
Shutdown Mode
VCC = 5.5V, VOH = 200mV
1000
800
VCC = 2.4V,
VOH = 200mV
VCC = 5.5V, VOH = 100mV
600
VCC = 2.4V,
VOH = 100mV
400
200
VCC = 5.5V, VOH = 50mV
VCC = 2.4V, VOH = 50mV
0
-60 -40
-20
0
20
40
60
80
Figure 5a. Output Source Current vs. Temperature
3000
VCC = 5.5V, VOL = 200mV
2500
2000
VCC = 2.4V, VOL = 200mV
VCC = 5.5V,
VOL = 100mV
1500
1000
500
VCC = 2.4V, VOL = 100mV
VCC = 5.5V, VOL = 50mV
VCC = 2.4V, VOL = 50mV
0
-60 -40
-20
0
20
40
60
80
TEMPERATURE (°C)
Figure 5b. Output Sink Current vs. Temperature
10
100
TEMPERATURE (°C)
Load-Driving Capability
The MAX4040–MAX4044 are fully guaranteed over temperature and supply voltage to drive a maximum resistive load of 25kΩ to VCC / 2, although heavier loads can
be driven in many applications. The rail-to-rail output
stage of the amplifier can be modeled as a current
source when driving the load toward VCC, and as a current sink when driving the load toward VEE. The magnitude of this current source/sink varies with supply
voltage, ambient temperature, and lot-to-lot variations
of the units.
Figures 5a and 5b show the typical current source and
sink capability of the MAX4040–MAX4044 family as a
function of supply voltage and ambient temperature.
The contours on the graph depict the output current
value, based on driving the output voltage to within
50mV, 100mV, and 200mV of either power-supply rail.
MAX4040-44 fig05a
1200
OUTPUT SOURCE CURRENT (µA)
The MAX4041 (single) and MAX4043 (dual) feature a
low-power shutdown mode. When the shutdown pin
(SHDN) is pulled low, the supply current drops to 1µA
per amplifier, the amplifier is disabled, and the outputs
enter a high-impedance state. Pulling SHDN high or
leaving it floating enables the amplifier. Take care to
ensure that parasitic leakage current at the SHDN pin
does not inadvertently place the part into shutdown
mode when SHDN is left floating. Figure 4 shows the
output voltage response to a shutdown pulse. The logic
threshold for SHDN is always referred to VCC / 2 (not to
GND). When using dual supplies, pull SHDN to VEE to
enter shutdown mode.
MAX4040-44 fig05b
Figure 3. Rail-to-Rail Input/Output Voltage Range
OUTPUT SINK CURRENT (µA)
MAX4040–MAX4044
Single/Dual/Quad, Low-Cost, SOT23,
Micropower, Rail-to-Rail I/O Op Amps
______________________________________________________________________________________
100
Single/Dual/Quad, Low-Cost, SOT23,
Micropower, Rail-to-Rail I/O Op Amps
RL =
RISO
2.4V - 0.1V
= 9.6kΩ to VEE
240µA
The same application can drive a 4.6kΩ load resistor
when terminated in VCC / 2 (+1.2V in this case).
MAX4040–
MAX4044
RL
CL
Driving Capacitive Loads
The MAX4040–MAX4044 are unity-gain stable for loads
up to 200pF (see Load Resistor vs. Capacitive Load
graph in Typical Operating Characteristics ).
Applications that require greater capacitive drive capability should use an isolation resistor between the output
and the capacitive load (Figures 6a–6c). Note that this
alternative results in a loss of gain accuracy because
RISO forms a voltage divider with the load resistor.
Power-Supply Bypassing and Layout
The MAX4040–MAX4044 family operates from either a
single +2.4V to +5.5V supply or dual ±1.2V to ±2.75V
supplies. For single-supply operation, bypass the
power supply with a 100nF capacitor to VEE (in this
case GND). For dual-supply operation, both the V CC
and VEE supplies should be bypassed to ground with
separate 100nF capacitors.
Good PC board layout techniques optimize performance by decreasing the amount of stray capacitance
at the op amp’s inputs and output. To decrease stray
capacitance, minimize trace lengths by placing external components as close as possible to the op amp.
Surface-mount components are an excellent choice.
AV =
Figure 6a. Using a Resistor to Isolate a Capacitive Load from
the Op Amp
MAX4040/42/44 fig06b
50mV/div
IN
50mV/div
OUT
100µs/div
RISO = NONE, RL = 100kΩ, CL = 700pF
Figure 6b. Pulse Response without Isolating Resistor
Using the MAX4040–MAX4044
as Comparators
Although optimized for use as operational amplifiers,
the MAX4040–MAX4044 can also be used as rail-to-rail
I/O comparators. Typical propagation delay depends
on the input overdrive voltage, as shown in Figure 7.
External hysteresis can be used to minimize the risk of
output oscillation. The positive feedback circuit, shown
in Figure 8, causes the input threshold to change when
the output voltage changes state. The two thresholds
create a hysteresis band that can be calculated by the
following equations:
VHYST = VHI - VLO
VLO = VIN x R2 / (R1 + (R1 x R2 / RHYST) + R2)
V HI = [(R2 / R1 x V IN ) + (R2 / R HYST ) x V CC ] /
(1 + R1 / R2 + R2 / RHYST)
RL
≈1
RL + RISO
MAX4040/42/44 fig06c
50mV/div
IN
50mV/div
OUT
100µs/div
RISO = 1kΩ, RL = 100kΩ, CL = 700pF
Figure 6c. Pulse Response with Isolating Resistor
______________________________________________________________________________________
11
MAX4040–MAX4044
For example, a MAX4040 running from a single +2.4V
supply, operating at TA = +25°C, can source 240µA to
within 100mV of VCC and is capable of driving a 9.6kΩ
load resistor to VEE:
MAX4040-44 fig07
10,000
HYSTERESIS
VHI
INPUT
VOH
VLO
tPD+; VCC = +5V
1000
tPD (µs)
MAX4040–MAX4044
Single/Dual/Quad, Low-Cost, SOT23,
Micropower, Rail-to-Rail I/O Op Amps
VOH
tPD-; VCC = +5V
OUTPUT
VOL
100
tPD+; VCC = +2.4V
VIN
RHYST
tPD-; VCC = +2.4V
R1
VCC
10
0
10 20 30 40 50 60 70 80
90 100
VOUT
VOD (mV)
R2
Figure 7. Propagation Delay vs. Input Overdrive
The MAX4040–MAX4044 contain special circuitry to
boost internal drive currents to the amplifier output
stage. This maximizes the output voltage range over
which the amplifiers are linear. In an open-loop comparator application, the excursion of the output voltage
is so close to the supply rails that the output stage transistors will saturate, causing the quiescent current to
increase from the normal 10µA. Typical quiescent currents increase to 35µA for the output saturating at VCC
and 28µA for the output at VEE.
Using the MAX4040–MAX4044
as Ultra-Low-Power Current Monitors
The MAX4040–MAX4044 are ideal for applications powered from a battery stack. Figure 9 shows an application
circuit in which the MAX4040 is used for monitoring the
current of a battery stack. In this circuit, a current load is
applied, and the voltage drop at the battery terminal is
sensed.
The voltage on the load side of the battery stack is
equal to the voltage at the emitter of Q1, due to the
feedback loop containing the op amp. As the load current increases, the voltage drop across R1 and R2
increases. Thus, R2 provides a fraction of the load current (set by the ratio of R1 and R2) that flows into the
emitter of the PNP transistor. Neglecting PNP base current, this current flows into R3, producing a ground-referenced voltage proportional to the load current. Scale
R1 to give a voltage drop large enough in comparison
to VOS of the op amp, in order to minimize errors.
The output voltage of the application can be calculated
using the following equation:
VOUT = [ILOAD x (R1 / R2)] x R3
12
MAX4040–
MAX4044
VEE
VEE
Figure 8. Hysteresis Comparator Circuit
ILOAD
R1
VCC
R2
Q1
VOUT
R3
MAX4040
VEE
Figure 9. Current Monitor for a Battery Stack
For a 1V output and a current load of 50mA, the choice
of resistors can be R1 = 2Ω, R2 = 100kΩ, R3 = 1MΩ.
The circuit consumes less power (but is more susceptible to noise) with higher values of R1, R2, and R3.
______________________________________________________________________________________
Single/Dual/Quad, Low-Cost, SOT23,
Micropower, Rail-to-Rail I/O Op Amps
TOP VIEW
N.C. 1
IN- 2
8
N.C.
N.C.
1
7
VCC
IN-
2
MAX4040
8
SHDN
OUTA 1
7
VCC
INA- 2
OUT
IN+
3
6
OUT
VEE 4
5
N.C.
VEE 4
5
N.C.
SO/µMAX
INAINA+
3
VEE
4
SHDNA
5
6
INB-
VEE 4
5
INB+
SO/µMAX
14 VCC
OUTA 1
14 OUTD
OUTA 1
INA-
2
13 OUTB
INA-
2
13 IND-
8
INB-
INA+
3
12 INB-
INA+
3
12 IND+
7
INB+
11 INB+
VCC 4
10 N.C.
INB+ 5
10 INC+
SHDNA 6
9
SHDNB
INB- 6
9
INC-
N.C. 7
8
N.C.
OUTB 7
8
OUTC
6
µMAX
3
INA+
OUTB
9
MAX4043
OUTB
SO/µMAX
10 VCC
2
7
MAX4042
6
OUTA 1
VCC
MAX4041
3
IN+
8
SHDNB
VEE 4
MAX4043
N.C. 5
MAX4044
SO
11 VEE
SO
___________________Chip Information
MAX4040/MAX4041
TRANSISTOR COUNT: 234
MAX4042/MAX4043
TRANSISTOR COUNT: 466
MAX4044
TRANSISTOR COUNT: 932
SUBSTRATE CONNECTED TO VEE
______________________________________________________________________________________
13
MAX4040–MAX4044
_____________________________________________Pin Configurations (continued)
________________________________________________________Package Information
SOT5L.EPS
MAX4040–MAX4044
Single/Dual/Quad, Low-Cost, SOT23,
Micropower, Rail-to-Rail I/O Op Amps
14
______________________________________________________________________________________
Single/Dual/Quad, Low-Cost, SOT23,
Micropower, Rail-to-Rail I/O Op Amps
8LUMAXD.EPS
______________________________________________________________________________________
15
MAX4040–MAX4044
___________________________________________Package Information (continued)
Single/Dual/Quad, Low-Cost, SOT23,
Micropower, Rail-to-Rail I/O Op Amps
10LUMAXB.EPS
MAX4040–MAX4044
Package Information (continued)
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
16 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 1998 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.