AD DAC8143

a
FEATURES
Fast, Flexible, Microprocessor Interfacing in Serially
Controlled Systems
Buffered Digital Output Pin for Daisy-Chaining
Multiple DACs
Minimizes Address-Decoding in Multiple DAC
Systems—Three-Wire Interface for Any Number of DACs
One Data Line
One CLK Line
One Load Line
Improved Resistance to ESD
–40ⴗC to +85ⴗC for the Extended Industrial Temperature
Range
APPLICATIONS
Multiple-Channel Data Acquisition Systems
Process Control and Industrial Automation
Test Equipment
Remote Microprocessor-Controlled Systems
12-Bit Serial Daisy-Chain
CMOS D/A Converter
DAC8143
FUNCTIONAL BLOCK DIAGRAM
VDD
RFB
DAC8143
IOUT1
12-BIT
D/A CONVERTER
VREF
IOUT2
CLR
AGND
LD1
DAC REGISTER
LOAD
LD2
STB1
STB4
CLK
STB3
INPUT 12-BIT
SHIFT REGISTER
STB2
IN
SRI
GENERAL INFORMATION
SRO
OUT
DGND
The DAC8143 is a 12-bit serial-input daisy-chain CMOS D/A
converter that features serial data input and buffered serial data
output. It was designed for multiple serial DAC systems, where
serially daisy-chaining one DAC after another is greatly simplified.
ADDRESS BUS
The DAC8143 also minimizes address decoding lines enabling
simpler logic interfacing. It allows three-wire interface for any
number of DACs: one data line, one CLK line and one load line.
Serial data in the input register (MSB first) is sequentially
clocked out to the SRO pin as the new data word (MSB first) is
simultaneously clocked in from the SRI pin. The strobe inputs
are used to clock in/out data on the rising or falling (user
selected) strobe edges (STB1, STB2, STB3, STB4).
When the shift register’s data has been updated, the new data
word is transferred to the DAC register with use of LD1 and
LD2 inputs.
Separate LOAD control inputs allow simultaneous output updating of multiple DACs. An asynchronous CLEAR input
resets the DAC register without altering data in the input
register.
WR
DBX
ADDRESS
DECODER
SRI
STROBE
DAC8143
SRO LOAD
mP
SRI
STROBE
DAC8143
SRO LOAD
SRI
STROBE
DAC8143
Improved linearity and gain error performance permits reduced
circuit parts count through the elimination of trimming components. Fast interface timing reduces timing design considerations
while minimizing microprocessor wait states.
SRO LOAD
The DAC8143 is available in plastic packages that are compatible with autoinsertion equipment.
Plastic packaged devices come in the extended industrial temperature range of –40°C to +85°C.
SRI
STROBE
DAC8143
SRO LOAD
Figure 1. Multiple DAC8143s with Three-Wire Interface
REV. C
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 1999
DAC8143–SPECIFICATIONS
ELECTRICAL CHARACTERISTICS
Parameter
STATIC ACCURACY
Resolution
Nonlinearity
Differential Nonlinearity1
Gain Error2
Gain Tempco (∆Gain/∆Temp)3
Power Supply Rejection Ratio
(∆Gain/∆VDD)
Output Leakage Current4
Symbol
PSRR
ILKG
IZSE
Input Resistance7
RIN
Output Noise Voltage Density3, 11
DIGITAL INPUTS/OUTPUT
Digital Input HIGH
Digital Input LOW
Input Leakage Current12
Input Capacitance
Digital Output High
Digital Output Low
ANALOG OUTPUTS
Output Capacitance3
Output Capacitance3
TIMING CHARACTERISTICS3
Serial Input to Strobe Setup Times
(tSTB = 80 ns)
Min
FT
Q
THD
en
Typ
Max
Units
±1
±1
±2
±5
Bits
LSB
LSB
LSB
ppm/°C
12
∆VDD = ± 5%
TA = +25°C
TA = Full Temperature Range
TA = +25°C
TA = Full Temperature Range
VREF Pin
7
tS
VREF = 20 V p-p @ f = 10 kHz, TA = +25°C
VREF = 0 V, IOUT Load = 100 Ω, CEXT = 13 pF
VREF = 6 V rms @ 1 kHz
DAC Register Loaded with All 1s
10 Hz to 100 kHz Between RFB and IOUT
± 0.0006 ± 0.002
±5
± 25
± 0.002 ± 0.03
± 0.01 ± 0.15
11
15
%/%
nA
nA
LSB
LSB
kΩ
0.380
1
µs
2.0
20
mV p-p
nVs
–92
13
dB
nV/√Hz
VIH
VIL
IIN
CIN
VOH
VOL
VIN = 0 V to +5 V
VIN = 0 V
IOH = –200 µA
IOL = 1.6 mA
COUT1
COUT2
COUT1
COUT2
Digital Inputs = All 1s
Digital Inputs = All 0s
Digital Inputs = All 0s
Digital Inputs = All 1s
tDS1
tDS2
tDS3
STB1 Used as the Strobe
STB2 Used as the Strobe
STB3 Used as the Strobe TA = +25°C
TA = Full Temperature Range
STB4 Used as the Strobe
STB1 Used as the Strobe TA = +25°C
TA = Full Temperature Range
STB2 Used as the Strobe TA = +25°C
TA = Full Temperature Range
50
20
10
20
20
40
50
50
60
ns
ns
ns
ns
ns
ns
ns
ns
ns
STB3 Used as the Strobe
STB4 Used as the Strobe
80
80
ns
ns
tDS4
tDH1
tDH2
Serial Input to Strobe Hold Times
(tSTB = 80 ns)
Conditions
N
INL
DNL
GFSE
TCGFS
Zero Scale Error5, 6
AC PERFORMANCE
Output Current Settling Time3, 8
AC Feedthrough Error
(VREF to IOUT1)3, 9
Digital-to-Analog Glitch Energy3, 10
Total Harmonic Distortion3
(@ VDD = +5 V; VREF = +10 V; VOUT1 = VOUT2 = VAGND = VDGND = 0 V; TA = Full Temperature
Range specified under Absolute Maximum Ratings, unless otherwise noted.)
tDH3
tDH4
2.4
–2–
0.4
V
V
µA
pF
V
V
90
90
60
60
pF
pF
pF
pF
0.8
±1
8
4
REV. C
DAC8143
ELECTRICAL CHARACTERISTICS
(@ VDD = +5 V; VREF = +10 V; VOUT1 = V0UT2 = VAGND = VDGND = 0 V; TA = Full
Temperature Range specified under Absolute Maximum Ratings, unless otherwise noted.)
Parameter
STB to SRO Propagation Delay
13
Symbol
Conditions
tPD
TA = +25°C
TA = Full Temperature Range
SRI Data Pulsewidth
STB1 Pulsewidth (STB1 = 80 ns)14
STB2 Pulsewidth (STB2 = 100 ns)14
STB3 Pulsewidth (STB3 = 80 ns)14
STB4 Pulsewidth (STB4 = 80 ns)14
Load Pulsewidth
tSRI
tSTB1
tSTB2
tSTB3
tSTB4
tLD1, tLD2
LSB Strobe into Input Register
to Load DAC Register Time
CLR Pulsewidth
tASB
tCLR
POWER SUPPLY
Supply Voltage
Supply Current
VDD
IDD
Power Dissipation
PD
TA = +25°C
TA = Full Temperature Range
Min
Max
Units
220
300
100
80
80
80
80
140
180
ns
ns
ns
ns
ns
ns
ns
ns
ns
0
80
ns
ns
4.75
All Digital Inputs = VIH or VIL
All Digital Inputs = 0 V or VDD
Digital Inputs = 0 V or VDD
5 V × 0.1 mA
Digital Inputs = VIH or VIL
5 V × 2 mA
DAC8143
Typ
5
5.25
2
0.1
0.5
V
mA
mA
mW
10
mW
NOTES
11
All grades are monotonic to 12 bits over temperature.
12
Using internal feedback resistor.
13
Guaranteed by design and not tested.
14
Applies to IOUT1; all digital inputs = V IL, VREF = +10 V; specification also applies for I OUT2 when all digital inputs = V IH.
15
VREF = +10 V, all digital inputs = 0 V.
16
Calculated from worst case R REF: IZSE (in LSBs) = (RREF × ILKG × 4096) /VREF.
17
Absolute temperature coefficient is less than +300 ppm/°C.
18
IOUT, Load = 100 Ω. CEXT = 13 pF, digital input = 0 V to V DD or VDD to 0 V. Extrapolated to 1/2 LSB: t S = propagation delay (t PD) +9 τ, where τ equals measured
time constant of the final RC decay.
19
All digital inputs = 0 V.
10
VREF = 0 V, all digital inputs = 0 V to V DD or VDD to 0 V.
11
Calculations from e n = √4K TRB where:
K = Boltzmann constant, J/KR = resistance Ω
T = resistor temperature, K B = bandwidth, Hz
12
Digital inputs are CMOS gates; I IN typically 1 nA at +25°C.
13
Measured from active strobe edge (STB) to new data output at SRO; C L = 50 pF.
14
Minimum low time pulsewidth for STB 1, STB2, and STB4, and minimum high time pulsewidth for STB 3.
Specifications subject to change without notice.
REV. C
–3–
DAC8143
ABSOLUTE MAXIMUM RATINGS
PIN CONNECTIONS
(TA = +25°C, unless otherwise noted.)
16-Lead Epoxy Plastic DIP
16-Lead SOIC
VDD to DGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +17 V
VREF to DGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 25 V
VRFB to DGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 25 V
AGND to DGND . . . . . . . . . . . . . . . . . . . . . . . . VDD + 0.3 V
DGND to AGND . . . . . . . . . . . . . . . . . . . . . . . . VDD + 0.3 V
Digital Input Voltage Range . . . . . . . . . . . . . . . –0.3 V to VDD
Output Voltage (Pin 1, Pin 2) . . . . . . . . . . . . . . –0.3 V to VDD
Operating Temperature Range
FP/FS Versions . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Storage Temperature . . . . . . . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (Soldering, 60 sec) . . . . . . . . . . . . +300°C
Package Type
␪JA*
␪JC
Units
16-Lead Plastic DIP
16-Lead SOIC
76
92
33
27
°C/W
°C/W
IOUT1 1
16
RFB
IOUT2 2
15
VREF
AGND 3
14
VDD
13
CLR
STB1 4
DAC8143
TOP VIEW
LD1 5 (Not to Scale) 12 DGND
SRO 6
11 STB4
SRI 7
10
STB3
STB2 8
9
LD2
*θJA is specified for worst case mounting conditions, i.e., θJA is specified for
device in socket for P-DIP package; θJA is specified for device soldered to
printed circuit board for SOIC package.
CAUTION
1. Do not apply voltage higher than VDD or less than DGND potential on any terminal except VREF (Pin 15) and RFB (Pin 16).
2. The digital control inputs are Zener-protected; however,
permanent damage may occur on unprotected units from
high energy electrostatic fields. Keep units in conductive
foam at all times until ready to use.
3. Use proper antistatic handling procedures.
4. Absolute Maximum Ratings apply to packaged devices.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device.
ORDERING GUIDE
Model
Nonlinearity
Gain
Error
Temperature
Range
Package
Descriptions
Package
Options
DAC8143FP
DAC8143FS
± 1 LSB
± 1 LSB
± 2 LSB
± 2 LSB
–40°C to +85°C
–40°C to +85°C
16-Lead Plastic DIP
16-Lead SOIC
N-16
R-16W
Die Size: 99 × 107 mil, 10,543 sq. mils.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the DAC8143 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
–4–
WARNING!
ESD SENSITIVE DEVICE
REV. C
Typical Performance Characteristics– DAC8143
VIN = 5V rms
OUTPUT OP AMP: OP-42
12
60
72
THD – dB
48
ATTENUATION – dB
24
36
0.032
–70
0
84
–75
0.018
–80
0.010
–85
0.0056
–90
0.0032
THD – %
ALL BITS ON
(MSB) B11
B10
B9
B8
B7
DATA BITS "ON"
B6
(ALL OTHER
B5
DATA BITS "OFF")
B4
B3
B2
B1
(LSB) B0
96
100
1k
10k
100k
FREQUENCY – Hz
108
10M
1M
–95
10
Figure 2. Multiplying Mode Frequency
Response vs. Digital Code
3
100
1k
10k
FREQUENCY – Hz
0.0018
100k
Figure 3. Multiplying Mode Total Harmonic
Distortion vs. Frequency
0.5
0.5
IDD – mA
2
1
0.3
0.25
0.2
INL – LSB
LINEARITY ERROR – LSB
0.4
0.1
0.0
–0.1
0
–0.2
–0.25
–0.3
–0.4
0
0
1
2
3
VIN – Volts
4
–0.5
5
Figure 4. Supply Current vs. Logic
Input Voltage
0
512 1024 1536 2048 2560 3072 3584 4095
DIGITAL INPUT CODE – Decimal
Figure 5. Linearity Error vs. Digital
Code
4
–0.5
2
4
6
VREF – Volts
8
10
Figure 6. Linearity Error vs. Reference Voltage
0.5
40
OUTPUT CURRENT – mA
SOURCE
SINK
3
0.25
DNL – LSB
THRESHOLD VOLTAGE – Volts
TA = +258C
30
2.4
2
1
–0.8
0
–0.25
0
1
3
5
7
9
11
VDD – Volts
13
15
17
Figure 7. Logic Threshold Voltage
vs. Supply Voltage
REV. C
–0.5
LOGIC 0
20
10
0
–10
LOGIC 1
–20
–30
–40
2
4
6
VREF – Volts
8
10
Figure 8. DNL Error vs. Reference
Voltage
–5–
0
1
2
3
4
SRO – VOLTAGE OUT – Volts
5
Figure 9. Digital Output Voltage vs.
Output Current
DAC8143
DEFINITION OF SPECIFICATIONS
A simplified circuit of the DAC8143 is shown in Figure 10. An
inversed R-2R ladder network consisting of silicon-chrome,
thin-film resistors, and twelve pairs of NMOS current-steering
switches. These switches steer binarily weighted currents into
either IOUT1 or IOUT2. Switching current to IOUT1 or IOUT2 yields
a constant current in each ladder leg, regardless of digital input
code. This constant current results in a constant input resistance at VREF equal to R (typically 11 kΩ). The VREF input may
be driven by any reference voltage or current, ac or dc, that is
within the limits stated in the Absolute Maximum Ratings chart.
RESOLUTION
The resolution of a DAC is the number of states (2n) into which
the full-scale range (FSR) is divided (or resolved), where “n” is
equal to the number of bits.
SETTLING TIME
Time required for the analog output of the DAC to settle to
within 1/2 LSB of its final value for a given digital input stimulus; i.e., zero to full-scale.
The twelve output current-steering switches are in series with
the R-2R resistor ladder, and therefore, can introduce bit errors.
It was essential to design these switches such that the switch
“ON” resistance be binarily scaled so that the voltage drop
across each switch remains constant. If, for example, Switch 1
of Figure 10 was designed with an “ON” resistance of 10 Ω,
Switch 2 for 20 Ω, etc., a constant 5 mV drop would then be
maintained across each switch.
GAIN
Ratio of the DAC’s external operational amplifier output voltage
to the VREF input voltage when all digital inputs are HIGH.
FEEDTHROUGH ERROR
Error caused by capacitive coupling from VREF to output.
Feedthrough error limits are specified with all switches off.
To further ensure accuracy across the full temperature range,
permanently “ON” MOS switches were included in series with
the feedback resistor and the R-2R ladder’s terminating resistor.
The Simplified DAC Circuit, Figure 10, shows the location of
these switches. These series switches are equivalently scaled to
two times Switch 1 (MSB) and top Switch 12 (LSB) to maintain constant relative voltage drops with varying temperature.
During any testing of the resistor ladder or RFEEDBACK (such as
incoming inspection), VDD must be present to turn “ON” these
series switches.
OUTPUT CAPACITANCE
Capacitance from IOUT1 to ground.
OUTPUT LEAKAGE CURRENT
Current appearing at IOUT1 when all digital inputs are LOW, or
at IOUT2 terminal when all inputs are HIGH.
GENERAL CIRCUIT INFORMATION
The DAC8143 is a 12-bit serial-input, buffered serial-output,
multiplying CMOS D/A converter. It has an R-2R resistor ladder network, a 12-bit input shift register, 12-bit DAC register,
control logic circuitry, and a buffered digital output stage.
VREF
The control logic forms an interface in which serial data is
loaded, under microprocessor control, into the input shift register and then transferred, in parallel, to the DAC register. In
addition, buffered serial output data is present at the SRO pin
when input data is loaded into the input register. This buffered
data follows the digital input data (SRI) by 12 clock cycles and
is available for daisy-chaining additional DACs.
10kV
10kV
10kV
20kV
20kV
20kV
20kV
S1
S2
S3
S12
20kV
*
IOUT2
10kV
*
BIT 1 (MSB) BIT 2
An asynchronous CLEAR function allows resetting the DAC
register to a zero code (0000 0000 0000) without altering data
stored in the registers.
BIT 3
BIT 12 (LSB)
DIGITAL INPUTS
(SWITCHES SHOWN FOR DIGITAL INPUTS "HIGH")
IOUT1
RFEEDBACK
*THESE SWITCHES
PERMANENTLY "ON"
Figure 10. Simplified DAC Circuit
–6–
REV. C
DAC8143
ESD PROTECTION
DYNAMIC PERFORMANCE
The DAC8143 digital inputs have been designed with ESD
resistance incorporated through careful layout and the inclusion
of input protection circuitry.
ANALOG OUTPUT IMPEDANCE
Figure 11 shows the input protection diodes. High voltage static
charges applied to the digital inputs are shunted to the supply
and ground rails through forward biased diodes.
These protection diodes were designed to clamp the inputs well
below dangerous levels during static discharge conditions.
The output resistance, as in the case of the output capacitance,
varies with the digital input code. This resistance, looking back
into the IOUT1 terminal, varies between 11 kΩ (the feedback
resistor alone when all digital input are LOW) and 7.5 kΩ (the
feedback resistor in parallel with approximately 30 kΩ of the
R-2R ladder network resistance when any single bit logic is
HIGH). Static accuracy and dynamic performance will be affected by these variations.
The gain and phase stability of the output amplifier, board
layout, and power supply decoupling will all affect the dynamic
performance of the DAC8143. The use of a small compensation
capacitor may be required when high speed operational amplifiers are used. It may be connected across the amplifier’s feedback resistor to provide the necessary phase compensation to
critically damp the output.
VDD
DTL/TTL/CMOS
INPUTS
The considerations when using high speed amplifiers are:
1. Phase compensation (see Figures 16 and 17).
2. Power supply decoupling at the device socket and use of
proper grounding techniques.
Figure 11. Digital Input Protection
EQUIVALENT CIRCUIT ANALYSIS
OUTPUT AMPLIFIER CONSIDERATIONS
Figures 12 and 13 show equivalent circuits for the DAC8143’s
internal DAC with all bits LOW and HIGH, respectively. The
reference current is switched to IOUT2 when all data bits are LOW,
and to IOUT1 when all bits are HIGH. The ILEAKAGE current
source is the combination of surface and junction leakages to the
substrate. The 1/4096 current source represents the constant
1-bit current drain through the ladder’s terminating resistor.
When using high speed op amps, a small feedback capacitor
(typically 5 pF–30 pF) should be used across the amplifiers to
minimize overshoot and ringing. For low speed or static
applications, ac specifications of the amplifier are not very critical. In high speed applications, slew rate, settling time, openloop gain and gain/phase margin specifications of the amplifier
should be selected for the desired performance. It has already
been noted that an offset can be caused by including the usual
bias current compensation resistor in the amplifier’s noninverting input terminal. This resistor should not be used. Instead, the
amplifier should have a bias current that is low over the temperature range of interest.
Output capacitance is dependent upon the digital input code.
This is because the capacitance of a MOS transistor changes
with applied gate voltage. This output capacitance varies between the low and high values.
IOUT1
Static accuracy is affected by the variation in the DAC’s output
resistance. This variation is best illustrated by using the circuit
of Figure 14 and the equation:
IOUT2
VERROR = VOS 1+ R 

O 
RFEEDBACK
R = 10kV
I LEAKAGE
I REF
60pF

R = 10kV
V REF
1/4096
I LEAKAGE
RFB 
90pF
R
R
R
VREF
Figure 12. Equivalent Circuit (All Inputs LOW)
ETC
R2
R2
RFB
R2
RFEEDBACK
I REF
R = 10kV
R = 10kV
OP-77
IOUT1
1/4096
V REF
I LEAKAGE
90pF
I LEAKAGE
60pF
VOS
IOUT2
Figure 14. Simplified Circuit
Figure 13. Equivalent Circuit (All Inputs HIGH)
REV. C
–7–
DAC8143
Where RO is a function of the digital code, and:
Serial data output (SRO) follows the serial data input (SRI) by
12 clocked bits.
RO = 10 kΩ for more than four bits of Logic 1,
RO = 30 kΩ for any single bit of Logic 1.
Holding any STROBE input at its selected state (i.e., STB1,
STB2 or STB4 at logic HIGH or STB3 at logic LOW) will act to
prevent any further data input.
Therefore, the offset gain varies as follows:
at code 0011 1111 1111,
VERROR1 = VOS
When a new data word has been entered into the input register,
it is transferred to the DAC register by asserting both LOAD
inputs.
 10 kΩ
1+ 10 kΩ = 2 VOS


The CLR input allows asynchronous resetting of the DAC register to 0000 0000 0000. This reset does not affect data held in
the input registers. While in unipolar mode, a CLEAR will
result in the analog output going to 0 V. In bipolar mode, the
output will go to –VREF.
at code 0100 0000 0000,
 10 kΩ 
VERROR2 = VOS 1+ 30 kΩ = 4/3 VOS


The error difference is 2/3 VOS.
INTERFACE INPUT DESCRIPTION
Since one LSB has a weight (for VREF = +10 V) of 2.4 mV for
the DAC8143, it is clearly important that VOS be minimized,
using either the amplifier’s pulling pins, an external pulling
network, or by selection of an amplifier with inherently low VOS.
Amplifiers with sufficiently low VOS include OP77, OP97, OP07,
OP27, and OP42.
STB1 (Pin 4), STB2 (Pin 8), STB4 (Pin 11)—Input Register
and Buffered Output Strobe. Inputs Active on Rising
Edge. Selected to load serial data into input register and buffered output stage. See Table I for details.
STB3 (Pin 10)—Input Register and Buffered Output
Strobe Input. Active on Falling Edge. Selected to load serial
data into input register and buffered output stage. See Table I
for details.
INTERFACE LOGIC OPERATION
The microprocessor interface of the DAC8143 has been designed with multiple STROBE and LOAD inputs to maximize interfacing options. Control signals decoding may be done on chip or
with the use of external decoding circuitry (see Figure 21).
LD1 (Pin 5), LD2 (Pin 9)—Load DAC Register Inputs.
Active Low. Selected together to load contents of input register
into DAC register.
CLR (Pin 13)—Clear Input. Active Low. Asynchronous.
When LOW, 12-bit DAC register is forced to a zero code (0000
0000 0000) regardless of other interface inputs.
Serial data is clocked into the input register and buffered output
stage with STB1, STB2, or STB4. The strobe inputs are active
on the rising edge. STB3 may be used with a falling edge clock
data.
WORD N –1
BIT 1
MSB
SRI
WORD N
BIT 2
BIT 12
LSB
BIT 1
MSB
tDH1, tDH2, tDH3, tDH4
tDS1, tDS2, tDS3, tDS4
SRO
BIT 11
BIT 12
LSB
tSR1
WORD N –2
BIT 1
MSB
BIT 2
WORD N –1
BIT 2
BIT 1
MSB
WORD N
BIT 2
BIT 12
LSB
BIT 1
LSB
tPD
* STROBE
(STB1, STB2, STB4)
1
tSTB1
tSTB2
tSTB3
tSTB4
2
12
tSTB1
tSTB2
tSTB3
tSTB4
1
tASB
2
11
12
tLD1
tLD2
LD1 AND LD2
LOAD INPUT REGISTER'S
DATA INTO DAC REGISTER
LOAD NEW 12-BIT WORD INTO
INPUT REGISTER AND SHIFT
OUT PREVIOUS WORD
NOTES:
* STROBE WAVEFORM IS INVERTED IF
STB3 IS USED TO STROBE SERIAL DATA
BITS INTO INPUT REGISTER.
** DATA IS STROBED INTO AND OUT OF
THE INPUT SHIFT REGISTER MSB FIRST.
Figure 15. Timing Diagram
–8–
REV. C
DAC8143
Table I. Truth Table
DAC8143 Logic Inputs
Input Register/
Digital Output
Control Inputs
STB4
STB3
STB2
STB1
0
0
0
g
1
1
f
1
0
g
0
0
g
0
0
0
1
X
X
X
X
0
X
X
X
X
1
X
X
X
X
1
DAC Register
CLR
Control Inputs
LD2
LD1
DAC8143 Operation
Notes
X
X
X
X
X
X
X
X
Serial Data Bit Loaded from SRI
into Input Register and Digital Output
(SRO Pin) after 12 Clocked Bits.
2, 3
No Operation (Input Register and SRO)
3
Reset DAC Register to Zero Code
(Code: 0000 0000 0000)
(Asynchronous Operation)
1, 3
X
X
X
X
0
X
X
1
1
1
X
X
1
No Operation (DAC Register and SRO)
3
1
0
0
Load DAC Register with the Contents
of Input Register
3
NOTES
1
CLR = 0 asynchronously resets DAC Register to 0000 0000 0000, but has no effect on Input Register.
2
Serial data is loaded into Input Register MSB first, on edges shown. g is positive edge, f is negative edge.
3
0 = Logic LOW, 1 = Logic HIGH, X = Don’t Care.
APPLICATIONS INFORMATION
The circuit shown in Figures 16 and 17 may be used with an ac
or dc reference voltage. The circuit’s output will range between
0 V and +10(4095/4096) V depending upon the digital input
code. The relationship between the digital input and the analog
output is shown in Table II. The VREF voltage range is the maximum input voltage range of the op amp or ± 25 V, whichever is
lowest.
CLR
MSB
LSB
1111 1111 1111
–VREF
1000 0000 0000
–VREF
0111 1111 1111
0000 0000 0001
0000 0000 0000
–VREF
–VREF
–VREF
2
SRI
(SERIAL
DATA IN)
VREF
–10V
 2049 
 4096 
VREF
 2048 
 4096  = – 2
 2047 
 4096 
 1 
 4096 
 0 
 4096  = 0
2
3
7
+15V
2
I OUT2
3
AGND
7
6
OP-77
VOUT
4
6
12
R1
100V
–15V
SRO
(BUFFERED
DIGITAL
DATA OUT)
+5V
VREF
CLR
VDD
15
13
1
DAC8143
8–11
SRI
(SERIAL
DATA IN)
7
RFEEDBACK
14
4, 5
CONTROL
INPUTS
2
3
12
DGND
6
I OUT1
R2
50V
+15V
15pF
2
I OUT2
AGND
SRO
(BUFFERED
DIGITAL
DATA OUT)
3
7
6
OP-42
VOUT
4
–15V
Figure 17. Unipolar Operation with Fast Op Amp and
Gain Error Trimming (2-Quadrant)

LSB = VREF  4096  or VREF(2–n).


REV. C
1
DAC8143
I OUT1
Figure 16. Unipolar Operation with High Accuracy Op
Amp (2-Quadrant)
Nominal LSB magnitude for the circuits of Figures 16 and 17 is given by
1
RFEEDBACK
15pF
DGND
 4095
 4096  .



14
8–11
NOTES
1
Nominal full scale for the circuits of Figures 16 and 17 is given by
FS = –VREF
15
13
4, 5
Nominal Analog Output
(VOUT as Shown
in Figures 16 and 17)
 4095
–VREF  4096


1000 0000 0001
VDD
VREF
CONTROL
INPUTS
Table II. Unipolar Code Table
Digital Input
+5V
VREF
–10V
UNIPOLAR OPERATION (2-QUADRANT)
–9–
DAC8143
Table III. Bipolar (Offset Binary) Code Table
In many applications, the DAC8143’s zero scale error and low
gain error, permit the elimination of external trimming components without adverse effects on circuit performance.
For applications requiring a tighter gain error than 0.024% at
25°C for the top grade part, or 0.048% for the lower grade part,
the circuit in Figure 17 may be used. Gain error may be trimmed
by adjusting R1.
Digital Input
MSB
Nominal Analog Output
(VOUT as Shown in Figure 18)
LSB
 2047 
1111 1111 1111
+VREF  2048 
1000 0000 0001
The DAC register must first be loaded with all 1s. R1 is then
adjusted until VOUT = –VREF (4095/4096). In the case of an
adjustable VREF, R1 and RFEEDBACK may be omitted, with VREF
adjusted to yield the desired full-scale output.
+VREF 
2048 
1000 0000 0000
0
0111 1111 1111
–VREF  2048 
BIPOLAR OPERATION (4-QUADRANT)
0000 0000 0001
–VREF 
2048 
0000 0000 0000
–VREF  2048 
Figure 18 details a suggested circuit for bipolar, or offset binary,
operation. Table III shows the digital input-to-analog output
relationship. The circuit uses offset binary coding. Twos complement code can be converted to offset binary by software inversion of the MSB or by the addition of an external inverter to the
MSB input.
Resistor R3, R4 and R5 must be selected to match within 0.01%
and must all be of the same (preferably metal foil) type to assure
temperature coefficient match. Mismatching between R3 and
R4 causes offset and full-scale error.
Calibration is performed by loading the DAC register with
1000 0000 0000 and adjusting R1 until VOUT = 0 V. R1 and
R2 may be omitted by adjusting the ratio of R3 to R4 to yield
VOUT = 0 V. Full scale can be adjusted by loading the DAC
register with 1111 1111 1111 and adjusting either the amplitude
of VREF or the value of R5 until the desired VOUT is achieved.
14
12
15
VIN
R1
100V
SERIAL
DATA INPUT
7
DGND
VREF
VDD
IOUT1
DAC8143
CONTROL
SRI BITS
8-11
RFB
4, 5
IOUT2
CLR SRO
13
AGND

1 
 2047 
 2048 
2
Nominal LSB magnitude for the circuits of Figure 18 is given by
 1 
LSB = VREF 
.
2048 
DAISY-CHAINING DAC8143s
Many applications use multiple serial input DACs that use
numerous interconnecting lines for address decoding and data
lines. In addition, they use some type of buffering to reduce
loading on the bus. The DAC8143 is ideal for just such an
application. It not only reduces the number of interconnecting
lines, but also reduces bus loading. The DAC8143 can be daisychained with only three lines: one data line, one CLK line and
one load line, see Figure 19.
R4
20kV
C1
10-33pF
15
1 
NOTES
1
Nominal full scale for the circuits of Figure 18 is given by
 2047 
FS = VREF 
.
2048 
R2
50V
+5V

1
A1
1/2 OP200
2
3
R5
20kV
R3
10kV
A2
1/2 OP200
VOUT
6
COMMON GROUND
BUFFERED SERIAL
DATA OUT
FROM
SYSTEM
RESET
CONTROL
INPUTS
Figure 18. Bipolar Operation (4-Quadrant, Offset Binary)
–10–
REV. C
DAC8143
APPLICATION TIPS
In most applications, linearity depends on the potential of IOUT1,
IOUT2, and AGND (Pins 1, 2 and 3) being exactly equal to each
other. In most applications, the DAC is connected to an external op amp with its noninverting input tied to ground (see Figures 16 and 17). The amplifier selected should have a low input
bias current and low drift over temperature. The amplifier’s
input offset voltage should be nulled to less than ± 200 µV (less
than 10% of 1 LSB).
ADDRESS BUS
ADDRESS
DECODER
WR
DBX
SRI
STROBE
SRO
DAC8143
LOAD
mP
SRI
The operational amplifier’s noninverting input should have a
minimum resistance connection to ground; the usual bias current compensation resistor should not be used. This resistor can
cause a variable offset voltage appearing as a varying output
error. All grounded pins should tie to a single common ground
point, avoiding ground loops. The VDD power supply should
have a low noise level with no transients greater than +17 V.
STROBE
DAC8143
SRO LOAD
SRI
STROBE
SRO
SRI
DAC8143
LOAD
It is recommended that the digital inputs be taken to ground or
VDD via a high value (1 MΩ) resistor; this will prevent the accumulation of static charge if the PC card is disconnected from the
system.
STROBE
DAC8143
SRO LOAD
Peak supply current flows as the digital input pass through the
transition region (see Figure 4). The supply current decreases as
the input voltage approaches the supply rails (VDD or DGND),
i.e., rapidly slewing logic signals that settle very near the supply
rails will minimize supply current.
Figure 19. Multiple DAC8143s with Three-Wire Interface
ANALOG/DIGITAL DIVISION
The transfer function for the DAC8143 connect in the multiplying mode as shown in Figures 16 and 17 is:
VO = –VIN
INTERFACING TO THE MC6800
 A1 A2 A3
A12 
 21 + 2 2 + 2 3 + ... 2 12 


As shown in Figure 21, the DAC8143 may be interfaced to the
6800 by successively executing memory WRITE instruction
while manipulating the data between WRITEs, so that each
WRITE presents the next bit.
where AX assumes a value of 1 for an “ON” bit and 0 for an
“OFF” bit.
The transfer function is modified when the DAC is connected in
the feedback of an operational amplifier as shown in Figure 20
and is:
In this example, the most significant bits are found in memory
locations 0000 and 0001. The four MSBs are found in the lower
half of 0000, the eight LSBs in 0001. The data is taken from the
DB7 line.


–VIN


VO =  A1 A2 A3
A12 
 + + 3 + ...

 21 22 2
212 
The serial data loading is triggered by STB4 which is asserted by
a decoded memory WRITE to a memory location, R/W, and
Φ2. A WRITE to another address location transfers data from
input register to DAC register.
The above transfer function is the division of an analog voltage
(VREF) by a digital word. The amplifier goes to the rails with all
bits “OFF” since division by zero is infinity. With all bits “ON”
the gain is 1 (± 1 LSB). The gain becomes 4096 with the LSB,
Bit 12, “ON”.
A0
A15
MC6800
DIGITAL
INPUTS
4
VIN
16
VDD
SRO
DAC8143
1
IOUT1
AGND 3
R/W
E1
φ2
E3
E2
13
RFB
16-BIT ADDRESS BUS
VREF
A0 A2
74LS138
ADDRESS
DECODER
DB0
14
6
15
DB7
+5V
BUFFERED DIGITAL
DATA OUT
+5V
8-BIT DATA BUS
SRI
LD2 STB1
STB3
DAC8143*
LD1
SRO
STB2
STB4
CLR
2 12 DGND
FROM SYSTEM RESET
2
*ANALOG CIRCUITRY OMITTED FOR SIMPLICITY
–
OP-42
6
Figure 21. DAC8143—MC6800 Interface
VOUT
3 +
Figure 20. Analog/Digital Divider
REV. C
–11–
DAC8143
DAC8143 INTERFACE TO THE 8085
DAC8143 INTERFACE TO THE 68000
The DAC8143’s interface to the 8085 microprocessor is shown
in Figure 22. Note that the microprocessor’s SOD line is used
to present data serially to the DAC.
Figure 23 shows the DAC8143 configured to the 68000 microprocessor. Serial data input is similar to that of the 6800 in
Figure 21.
Data is strobed into the DAC8143 by executing memory write
instructions. The strobe 2 input is generated by decoding an
address location and WR. Data is loaded into the DAC register
with a memory write instruction to another address location.
A1
Serial data supplied to the DAC8143 must be present in the
right-justified format in registers H and L of the microprocessor.
CS
AS
C3114c–2–3/99
ADDRESS BUS
A23
ADDRESS
DECODER
68000mP
+
VMA
ADDRESS BUS (16)
A0–A15
(8)
8085
VPA
ALE
E1
8212
E3
+5V
WR
E2
(8) AD0–7
UDS
SRI
+5V
STB3 STB1 LD2
LD1
STB2 DAC8143
STB4
SRI
CLR
FROM SYSTEM RESET
DATA
SOD
+5V
1/4 74HC125
A0
A2
74LS138
ADDRESS
DECODER
DB15
DATA BUS
DB0
LD2
STB2
STB3
STB1 DAC8143*
SRO
STB4
LD1
CLR
Figure 23. DAC8143 to 68000 µ P Interface
FROM SYSTEM RESET
*ANALOG CIRCUITRY OMITTED FOR SIMPLICITY
Figure 22. DAC8143—8085 Interface
OUTLINE DIMENSIONS
Dimensions are shown in inches and (mm).
16-Lead Plastic DIP
(N-16)
16-Lead SOIC
(R-16W)
0.4133 (10.50)
0.3977 (10.00)
0.840 (21.34)
0.745 (18.92)
9
1
8
0.280 (7.11)
0.240 (6.10)
PIN 1
0.060 (1.52)
0.015 (0.38)
0.210 (5.33)
MAX
0.130
(3.30)
0.160 (4.06)
MIN
0.115 (2.93)
0.022 (0.558) 0.100 0.070 (1.77) SEATING
PLANE
(2.54)
0.014 (0.356)
BSC 0.045 (1.15)
16
9
0.2992 (7.60)
0.2914 (7.40)
0.325 (8.25)
0.300 (7.62)
1
8
0.195 (4.95)
0.115 (2.93)
PIN 1
0.015 (0.381)
0.008 (0.204)
0.050 (1.27)
BSC
0.0118 (0.30)
0.0040 (0.10)
–12–
0.4193 (10.65)
0.3937 (10.00)
0.1043 (2.65)
0.0926 (2.35)
88
0.0192 (0.49) SEATING
08
0.0125 (0.32)
PLANE
0.0138 (0.35)
0.0091 (0.23)
0.0291 (0.74)
3 458
0.0098 (0.25)
0.0500 (1.27)
0.0157 (0.40)
REV. C
PRINTED IN U.S.A.
16