RS2A THRU RS2K SURFACE MOUNT FAST SWITCHING RECTIFIER Reverse Voltage - 50 to 800 Volts DO-214AA MODIFIED J-BEND 0.086 (2.20) FEATURES 0.155 (3.94) 0.130 (3.30) 0.077 (1.95) Forward Current - 1.5 Amperes 0.180 (4.57) 0.160 (4.06) 0.012 (0.305) ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ For surface mount applications ♦ Low profile package ♦ Built-in strain relief, ideal for automated placement ♦ Glass passivated chip junction ♦ Fast switching for high efficiency ♦ High temperature soldering: 250°C/10 seconds at terminals 0.006 (0.152) 0.096 (2.44) 0.084 (2.13) MECHANICAL DATA 0.008 (0.203) MAX. 0.060 (1.52) 0.030 (0.76) 0.220 (5.59) 0.205 (5.21) Case: JEDEC DO-214AA molded plastic over passivated chip Terminals: Solder plated solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode band end Weight: 0.003 ounce, 0.093 gram Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS Device marking code RS2A RS2B RS2D RS2G RS2J RS2K RA RB RD RG RJ RK UNITS Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 Volts Maximum average forward rectified current at TL=100°C I(AV) 1.5 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 50.0 Amps VF 1.30 Volts IR 5.0 200.0 µA Maximum instantaneous forward voltage at 1.5A Maximum DC reverse current at rated DC blocking voltage TA=25°C TA=125°C Maximum reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Typical thermal resistance (NOTE 3) Operating junction and storage temperature range NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25 (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient and junction to lead P.C.B. mounted on 0.27 x 0.27” (7.0 x 7.0mm) copper pad areas 4/98 trr 150 250 500 ns CJ 50.0 pF RΘJA RΘJL 55.0 18.0 °C/W TJ, TSTG -55 to 150 °C RATINGS AND CHARACTERISTIC CURVES RS2A THRU RS2K FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT RESISTIVE OR INDUCTIVE LOAD 1.5 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD CURRENT, AMPERES FIG. 1 - FORWARD CURRENT DERATING CURVE 1.0 0.5 P.C.B. MOUNTED 0.27 x 0.27” (7.0 x 7.0mm) COPPER PAD AREAS 0 50 60 70 80 90 100110120130140150 160 50 TL=100°C 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 40 30 20 10 0 1 10 LEAD TEMPERATURE, °C 100 NUMBER OF CYCLES AT 60 HZ FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 100 20 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT AMPERES 10 PULSE WIDTH=300µs 1% DUTY CYCLE TJ=25°C 1 0.1 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 1 TJ=25°C 100 TJ=25°C f=1.0 MHZ Vsig=50mVp-p 10 REVERSE VOLTAGE, VOLTS 0 20 40 60 80 PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 5 - TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, pF 10 0.1 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 10 1 TJ=125°C 100 100