ES2A THRU ES2D SURFACE MOUNT FAST EFFICIENT PLASTIC RECTIFIER Reverse Voltage - 50 to 200 Volts Forward Current - 2.0 Amperes DO-214AA FEATURES 0.086 (2.20) 0.155 (3.94) 0.130 (3.30) 0.077 (1.95) 0.180 (4.57) 0.160 (4.06) 0.012 (0.305) 0.006 (0.152) 0.096 (2.44) 0.084 (2.13) ¨ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ¨ For surface mount applications ¨ Low profile package ¨ Built-in strain relief ¨ Ideal for automated placement ¨ Easy pick and place ¨ Glass passivated chip junction ¨ Superfast recovery times for high efficiency ¨ Low power loss, high efficiency ¨ High temperature soldering: 250¡C/10 seconds at terminals MECHANICAL DATA 0.008 (0.203) MAX. 0.060 (1.52) 0.030 (0.76) 0.220 (5.59) 0.205 (5.21) Dimensions in inches and (millimeters) Case: JEDEC DO-214AA molded plastic body over passivated chip Terminals: Solder plated solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Weight: 0.003 ounces, 0.093 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25¡C ambient temperature unless otherwise specified. SYMBOLS Device marking code ES2A ES2B ES2C ES2D EA EB EC ED UNITS Maximum repetitive peak reverse voltage VRRM 50 100 150 200 Volts Maximum RMS voltage VRMS 35 70 105 140 Volts VDC 50 100 150 200 Volts Maximum DC blocking voltage Maximum average forward rectified current at TL=110¡C I(AV) 2.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) at TL=110¡C IFSM 50.0 Amps VF 0.90 Volts IR 10.0 350 mA trr 20.0 ns TJ=25¡C TJ=100¡C trr 30.0 50.0 ns TJ=25¡C TJ=100¡C Qrr 10.0 25.0 nC Typical junction capacitance (NOTE 3) CJ 18.0 pF Maximum thermal resistance (NOTE 4) RQJA RQJL 75.0 20.0 ¡C/W TJ, TSTG -55 to +150 ¡C Maximum instantaneous forward voltage at 2.0A Maximum DC reverse current at rated DC blocking voltage TA=25¡C TA=100¡C Maximum reverse recovery time (NOTE 1) Maximum reverse recovery time (NOTE 2) Maximum stored charge (NOTE 2) Operating junction and storage temperature range NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR= I.0A, lrr=0.25A (2) Trr and Qrr measured at: IF=2.0A, VR=30V, di/dt=50A/ms, Irr=10% IR (3) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts (4) Units mounted on P.C.B. 5.0 x 5.0mm (0.013mm thick) land areas 2/10/99 RATING AND CHARACTERISTIC CURVES ES2A THRU ES2D FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT AVERAGE FORWARD RECTIFIED CURRENT, AMPERES RESISTIVE OR INDUCTIVE LOAD P.C.B. MOUNTED ON 0.2 x 0.2Ó (5.0 x 5.0mm) COPPER PAD AREAS 0 80 90 100 110 120 130 140 150 PEAK FORWARD SURGE CURRENT, AMPERES FIG. 1 - MAXIMUM FORWARD CURRENT DERATING CURVE 30 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) at TL=110¡C 25 20 15 10 5.0 0 1 100 10 LEAD TEMPERATURE, ¡C NUMBER OF CYCLES AT 60 HZ FIG. 4 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 1,000 100 TJ=125¡C 10 TJ=25¡C PULSE WIDTH=300ms 1% DUTY CYCLE 1 0.1 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 50 1 TJ=25¡C 0.1 0.01 0 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 40 20 80 60 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 5 - TYPICAL JUNCTION CAPACITANCE 100 14 JUNCTION CAPACITANCE, pF TJ=85¡C 10 TJ=25¡C f=1.0 MHZ Vsig=50mVp-p 12 10 8.0 10 6.0 4.0 2.0 0 0.1 1 10 100 REVERSE VOLTAGE, VOLTS 1 0.1 1 10 100