19-2336; Rev 1; 8/03 Low-Power, Single/Dual-Voltage µP Reset Circuits with Capacitor-Adjustable Reset Timeout Delay Features ♦ Monitor System Voltages from 1.6V to 5V ♦ Capacitor-Adjustable Reset Timeout Period ♦ Manual Reset Input (MAX6412/MAX6413/MAX6414) ♦ Adjustable Reset Input Option (MAX6415–MAX6420) ♦ Dual-Voltage Monitoring (MAX6418/MAX6419/MAX6420) ♦ Low Quiescent Current (1.7µA, typ) ♦ 3 RESET Output Options Push-Pull RESET Push-Pull RESET Open-Drain RESET ♦ Guaranteed Reset Valid to VCC = 1V ♦ Power-Supply Transient Immunity ♦ Small SOT23-5 Packages Ordering Information PART TEMP RANGE MAX6412UK_ _-T -40°C to +125°C 5 SOT23-5 MAX6413UK_ _-T -40°C to +125°C 5 SOT23-5 Automotive MAX6414UK_ _-T -40°C to +125°C 5 SOT23-5 Medical Equipment MAX6415UK-T -40°C to +125°C 5 SOT23-5 Intelligent Instruments MAX6416UK-T -40°C to +125°C 5 SOT23-5 Portable Equipment MAX6417UK-T -40°C to +125°C 5 SOT23-5 Battery-Powered Computers/Controllers MAX6418UK_ _-T -40°C to +125°C 5 SOT23-5 Embedded Controllers MAX6419UK_ _-T -40°C to +125°C 5 SOT23-5 Critical µP Monitoring MAX6420UK_ _-T -40°C to +125°C 5 SOT23-5 Applications Set-Top Boxes Computers Pin Configuration TOP VIEW RESET/RESET 1 GND 2 5 VCC 4 SRT MAX6412– MAX6420 RESET IN (MR) 3 SOT23-5 PIN-PACKAGE Note: The MAX6412/MAX6413/MAX6414 and MAX6418/ MAX6419/MAX6420 are available with factory-set VCC reset thresholds from 1.575V to 5.0V in approximately 0.1V increments. Insert the desired nominal reset threshold suffix (from Table 1) into the blanks following the letters UK. There are 33 standard versions with a required order increment of 2500 pieces. Sample stock is generally held on standard versions only (see Standard Versions Table). Required order increment is 10,000 pieces for nonstandard versions. Contact factory for availability. All devices are available in tape-and-reel only. Typical Operating Circuit appears at end of data sheet. Selector Guide appears at end of data sheet. ( ) FOR THE MAX6412/MAX6413/MAX6414. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1 MAX6412–MAX6420 General Description The MAX6412–MAX6420 low-power microprocessor supervisor circuits monitor system voltages from 1.6V to 5V. These devices are designed to assert a reset signal whenever the VCC supply voltage or RESET IN falls below its reset threshold or the manual reset input is asserted. The reset output remains asserted for the reset timeout period after VCC and RESET IN rise above the reset threshold and the manual reset input is deasserted. The reset timeout is externally set by a capacitor to provide more flexibility. The MAX6412/MAX6413/MAX6414 feature fixed thresholds from 1.575V to 5V in approximately 100mV increments and a manual reset input. The MAX6415/MAX6416/MAX6417 are offered with an adjustable reset input that can monitor voltages down to 1.26V and the MAX6418/MAX6419/ MAX6420 are offered with one fixed input and one adjustable input to monitor dual-voltage systems. The MAX6412/MAX6415/MAX6418 have an active-low, push-pull reset output. The MAX6413/MAX6416/ MAX6419 have an active-high, push-pull reset output and the MAX6414/MAX6417/MAX6420 have an activelow, open-drain reset output. All of these devices are offered in a SOT23-5 package and are fully specified from -40°C to +125°C. MAX6412–MAX6420 Low-Power, Single/Dual-Voltage µP Reset Circuits with Capacitor-Adjustable Reset Timeout Delay ABSOLUTE MAXIMUM RATINGS All Voltages Referenced to GND VCC ........................................................................-0.3V to +6.0V SRT, MR, RESET IN ....................................-0.3V to (VCC + 0.3V) RESET, RESET (Push-Pull) .........................-0.3V to (VCC + 0.3V) RESET (Open-Drain) .............................................-0.3V to +6.0V Input Current (All Pins) .....................................................±20mA Output Current (RESET, RESET) ......................................±20mA Continuous Power Dissipation (TA = +70°C) 5-Pin SOT23-5 (derate 7.1mW/°C above +70°C) ........571mW Operating Temperature Range .........................-40°C to +125°C Junction Temperature ......................................................+150°C Storage Temperature Range .............................-65°C to +150°C Lead Temperature (soldering, 10s) .................................+300°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VCC = 1V to 5.5V, TA = TMIN to TMAX, unless otherwise specified. Typical values are at VCC = 5V and TA = +25°C.) (Note 1) PARAMETER Supply Voltage Range SYMBOL CONDITIONS VCC MIN VCC ≤ 5.0V Supply Current ICC VTH VCC to Reset Delay Reset Timeout Period VSRT Ramp Current VSRT Ramp Threshold tRP IRAMP VTH-RAMP RAMP Threshold Hysteresis RESET Output Voltage LOW 2 3.5 2.5 VTH + 1.5% VTH + 2.5% VTH + 3.5% TA = 0°C to +125°C VTH 1.5% VTH 2.5% VTH 3.5% 3 ✕ VTH VCC falling at 1mV/µs CSRT = 1500pF 3.35 CSRT = 0 4.375 RESET Output Leakage Current, (Open-Drain) VOH ILKG 2 VOH ms VSRT = 0 to 0.65V; VCC = 1.6V to 5V 240 nA VCC = 1.6V to 5V (VRAMP rising) 0.65 V 33 mV VCC ≥ 1.0V, ISINK = 50µA 0.3 VCC ≥ 2.7V, ISINK = 1.2mA 0.3 V 0.4 VCC ≥ 1.8V, ISOURCE = 200µA 0.8 ✕ VCC VCC ≥ 2.25V, ISOURCE = 500µA 0.8 ✕ VCC VCC ≥ 4.5V, ISOURCE = 800µA 0.8 ✕ VCC VCC > VTH, reset not asserted VCC ≥ 1.0V, ISOURCE = 1µA RESET Output Voltage HIGH V µs 5.40 0.275 VCC ≥ 4.5V, ISINK = 3.2mA RESET Output Voltage HIGH, (Push-Pull) µA mV 100 VRAMP falling threshold VOL V 4.5 1.7 VHYST tRD UNITS 5.5 VCC ≤ 2.0V TA = -40°C to 0°C Hysteresis 2.7 MAX VCC ≤ 3.3V TA = +25°C VCC Reset Threshold Accuracy TYP 1.0 V 1.0 µA 0.8 ✕ VCC VCC ≥ 1.8V, ISOURCE = 150µA 0.8 ✕ VCC VCC ≥ 2.7V, ISOURCE = 500µA 0.8 ✕ VCC VCC ≥ 4.5V, ISOURCE = 800µA 0.8 ✕ VCC _______________________________________________________________________________________ V Low-Power, Single/Dual-Voltage µP Reset Circuits with Capacitor-Adjustable Reset Timeout Delay (VCC = 1V to 5.5V, TA = TMIN to TMAX, unless otherwise specified. Typical values are at VCC = 5V and TA = +25°C.) (Note 1) PARAMETER SYMBOL RESET Output Voltage LOW VOL CONDITIONS MIN TYP MAX VCC ≥ 1.8V, ISINK = 500µA 0.3 VCC ≥ 2.7V, ISINK = 1.2mA 0.3 VCC ≥ 4.5V, ISINK = 3.2mA 0.4 RESET IN Leakage Current UNITS V 10 RESET IN Threshold VRST VRST falling, VCC = 1.6V to 5.0V 1.212 RESET IN Hysteresis 1.263 nA 1.313 V 25 VIL 0.8 VCC > 4.0V VIH MR Input VIL 2.4 V 0.3 ✕ VCC VCC < 4.0V VIH mV 0.7 ✕ VCC MR Minimum Pulse Width 1 µs MR Glitch Rejection 75 ns MR to RESET Delay 50 µs MR Pullup Resistance Pull up to VCC 12 20 28 kΩ Note 1: Devices production tested at +25°C. Over temperature limits are guaranteed by design. Typical Operating Characteristics (VCC = 5V, CSRT = 1500pF, TA = +25°C, unless otherwise noted.) SUPPLY CURRENT vs. TEMPERATURE TA = +25°C 2 TA = -40°C 1 VCC = 5V 2.5 VCC = 3.3V 2.0 VCC = 1.8V 1.5 1.0 VCC = 1V 10,000 RESET TIMEOUT PERIOD (ms) 3 3.0 MAX6412-20 toc02 SUPPLY CURRENT (µA) TA = +125°C RESET TIMEOUT PERIOD vs. CSRT 3.5 SUPPLY CURRENT (µA) MAX6412-20 toc01 4 MAX6412-20 toc03 SUPPLY CURRENT vs. SUPPLY VOLTAGE 1000 100 10 1 0.5 0 0 0 1 2 3 4 SUPPLY VOLTAGE (V) 5 6 -50 -25 0 25 50 75 TEMPERATURE (°C) 100 125 0.1 0.001 0.01 0.1 1 10 100 1000 CSRT (nF) _______________________________________________________________________________________ 3 MAX6412–MAX6420 ELECTRICAL CHARACTERISTICS (continued) Typical Operating Characteristics (continued) (VCC = 5V, CSRT = 1500pF, TA = +25°C, unless otherwise noted.) RESET TIMEOUT PERIOD vs. TEMPERATURE 4.25 4.20 4.15 4.10 600 CSRT = 0 550 RESET TIMEOUT PERIOD (µs) CSRT = 1500pF 500 MAX6412-20 toc05 RESET TIMEOUT PERIOD vs. TEMPERATURE MAX6412-20 toc04 RESET TIMEOUT PERIOD (ms) 4.30 450 400 350 300 250 200 4.05 -50 -25 0 25 50 75 100 -50 125 -25 TEMPERATURE (°C) RESET IN THRESHOLD VOLTAGE vs. TEMPERATURE 25 75 50 TEMPERATURE (°C) 100 1.270 1.265 1.260 125 MAX6412-20 toc07 175 150 TRANSIENT DURATION (µs) 1.275 0 MAXIMUM TRANSIENT DURATION vs. RESET THRESHOLD OVERDRIVE MAX6412-20 toc06 1.280 RESET IN THRESHOLD VOLTAGE (V) MAX6412–MAX6420 Low-Power, Single/Dual-Voltage µP Reset Circuits with Capacitor-Adjustable Reset Timeout Delay 125 100 RESET OCCURS ABOVE THE CURVE 75 50 1.255 25 1.250 0 VTH = 3.0V -50 -25 0 25 50 75 TEMPERATURE (°C) 4 100 125 0 200 400 600 800 RESET THRESHOLD OVERDRIVE (mV) _______________________________________________________________________________________ 1000 Low-Power, Single/Dual-Voltage µP Reset Circuits with Capacitor-Adjustable Reset Timeout Delay PIN MAX6412/ MAX6413/ MAX6414 1 2 MAX6415/ MAX6416/ MAX6417 1 2 MAX6418/ MAX6419/ MAX6420 NAME RESET RESET changes from high to low whenever VCC or RESET IN drops below the selected reset threshold voltage (VTH or VRESET IN, respectively) or manual reset is pulled low. RESET remains low for the reset timeout period after all reset conditions are deasserted and then goes high. RESET RESET changes from low to high whenever the VCC or RESET IN drops below the selected reset threshold voltage (VTH or VRESET IN) or manual reset is pulled low. RESET remains high for the reset timeout period after all reset conditions are deasserted and then goes low. 1 2 FUNCTION GND Ground Reset Input. High-impedance input to the adjustable reset comparator. Connect RESET IN to the center point of an external resistor-divider network to set the threshold of the externally monitored voltage. See Reset Threshold section. — 3 3 RESET IN 3 — — MR Manual Reset Input. Pull this pin low to manually reset the device. Reset remains asserted for the reset timeout period after MR is released. 4 4 4 SRT Set Reset Timeout Input. Connect a capacitor between SRT and ground to set the timeout period. Determine the period as follows: tRP = (2.73 x 106) ✕ CSRT + 275µs with tRP in seconds and CSRT in Farads. 5 5 5 VCC Supply Voltage and Input for Fixed-Threshold VCC Monitor Detailed Description The MAX6412–MAX6420 low-power microprocessor (µP) supervisory circuits provide maximum adjustability for supply-voltage monitoring and reset functionality. In addition, the MAX6412–MAX6420 reset timeout period is adjustable using an external capacitor. The MAX6412/MAX6413/MAX6414 have factorytrimmed reset threshold voltages in approximately 100mV increments from 1.575V to 5.0V with a manual reset input. The MAX6415/MAX6416/MAX6417 contain a reset threshold that can be adjusted to any voltage above 1.26V using external resistors. The MAX6418/ MAX6419/MAX6420 offer both a factory-trimmed reset threshold and an adjustable reset threshold input for dual-voltage monitoring. A reset signal is asserted when VCC and/or RESET IN falls below the preset values or when MR is asserted. The reset remains asserted for an externally programmed interval after VCC and/or RESET IN has risen above the reset threshold or MR is deasserted. Reset Output in a known state. The MAX6412–MAX6420 µP supervisory circuits provide the reset logic to prevent codeexecution errors during power-up, power-down, and brownout conditions (see Typical Operating Circuit). For the MAX6413, MAX6416, and MAX6419, RESET changes from low to high whenever VCC or RESET IN drops below the reset threshold voltages. Once RESET IN and VCC exceed their respective reset threshold voltage(s), RESET remains high for the reset timeout period, then goes low. On power-up, once VCC reaches 1V, RESET is guaranteed to be a logic high. For applications requiring valid reset logic when VCC is less than 1V, see the section Ensuring a Valid RESET/RESET Output Down to VCC = 0. The active-low RESET output of the remaining supervisors is the inverse of the MAX6413, MAX6416, and MAX6419 active-high RESET output and is guaranteed valid for VCC ≥ 1V. Reset Threshold The MAX6415–MAX6420 monitor the voltage on RESET IN with an external resistor voltage-divider (Figure 1). The reset output is typically connected to the reset input of a µP. A µP’s reset input starts or restarts the µP _______________________________________________________________________________________ 5 MAX6412–MAX6420 Pin Description MAX6412–MAX6420 Low-Power, Single/Dual-Voltage µP Reset Circuits with Capacitor-Adjustable Reset Timeout Delay Use the following formula to calculate the externally monitored voltage (VMON_TH): VMON_TH = VRST ✕ (R1 + R2)/R2 where VMON_TH is the desired reset threshold voltage and VRST is the reset input threshold (1.26V). Resistors R1 and R2 can have very high values to minimize current consumption due to low leakage currents. Set R2 to some conveniently high value (1MΩ, for example) and calculate R1 based on the desired monitored voltage, using the following formula: R1 = R2 x (VMON_TH/VRST - 1) (Ω) VCC R1 RESET IN VCC R2 GND MAX6415– MAX6420 Manual Reset Input (MAX6412/MAX6413/MAX6414) Many µP based products require manual reset capability, allowing the operator, a technician, or external logic circuitry to initiate a reset. A logic low on MR asserts reset. Reset remains asserted while MR is low and for the reset timeout period after MR returns high. The MR has an internal 20kΩ pullup resistor so it can be left open if not used. Connect a normally open momentary switch from MR to ground to create a manual reset function (external debounce circuitry is not required for long reset timeout periods). A manual reset option can easily be implemented with the MAX6415–MAX6420 by connecting a normally open momentary switch in parallel with R2 (Figure 2). When the switch is closed, the voltage on RESET IN goes to zero, initiating a reset. Similar to the MAX6412/MAX6413/ MAX6414 manual reset, reset remains asserted while the switch is closed and for the reset timeout period after the switch is opened. VMON_TH SRT Figure 2. Adding an External Manual Reset Function to the MAX6415–MAX6420 Monitoring Voltages Other than VCC (MAX6415/MAX6416/MAX6417) The MAX6415/MAX6416/MAX6417 contain an adjustable reset threshold input. These devices can be used to monitor voltages other than VCC. Calculate VMON_TH as shown in the Reset Threshold section. (See Figure 3.) VMON_TH VCC R1 R1 RESET IN RESET IN VCC VCC R2 R2 GND MAX6415 MAX6416 MAX6417 GND MAX6415 MAX6416 MAX6417 SRT SRT VMON_TH = 1.26 x (R1 + R2) / R2 Figure 1. Calculating the Monitored Threshold Voltage (VMON_TH) 6 Figure 3. Monitoring External Voltages _______________________________________________________________________________________ Low-Power, Single/Dual-Voltage µP Reset Circuits with Capacitor-Adjustable Reset Timeout Delay MAX6412–MAX6420 VMON_TH VCC MAX6420 ONLY VCC LASER-TRIMMED RESISTORS RL RESET CIRCUITRY 1.26V (RESET) RESET µP R1 R2 RESET IN GND SRT MAX6418 MAX6419 MAX6420 CSRT Figure 4. MAX6418/MAX6419/MAX6420 Monitoring Two Voltages Dual-Voltage Monitoring (MAX6418/MAX6419/MAX6420) The MAX6418/MAX6419/MAX6420 contain both factory-trimmed threshold voltages and an adjustable reset threshold input, allowing the monitoring of two voltages, VCC and VMON_TH (see Figure 4). Reset is asserted when either of the voltages falls below its respective threshold voltage. Application Information Selecting a Reset Capacitor The reset timeout period is adjustable to accommodate a variety of µP applications. Adjust the reset timeout period (tRP) by connecting a capacitor (CSRT) between SRT and ground. Calculate the reset timeout capacitor as follows: CSRT = (tRP - 275µs) / (2.73 ✕ 106) The reset delay time is set by a current/capacitor-controlled ramp compared to an internal 0.65V reference. An internal 240nA ramp current source charges the external capacitor. The charge to the capacitor is cleared when a reset condition is detected. Once the reset condition is removed, the voltage on the capacitor ramps according to the formula: dV/dt = I/C. The CSRT capacitor must ramp to 0.65V to deassert the reset. CSRT must be a low-leakage (<10nA) type capacitor, ceramic is recommended. Operating as a Voltage Detector The MAX6412–MAX6420 can be operated in a voltage detector mode by floating the SRT pin. The reset delay times for VCC rising above or falling below the threshold are not significantly different. The reset output is deasserted smoothly without false pulses. where tRP is in seconds and CSRT is in Farads _______________________________________________________________________________________ 7 MAX6412–MAX6420 Low-Power, Single/Dual-Voltage µP Reset Circuits with Capacitor-Adjustable Reset Timeout Delay 5.0V 3.3V VCC 10kΩ RESET 5V SYSTEM MAX6414 MAX6417 MAX6420 GND impedance CMOS-logic inputs connected to RESET can drift to undetermined voltages. This presents no problems in most applications, since most µPs and other circuitry do not operate with VCC below 1V. In those applications where RESET must be valid down to 0, adding a pulldown resistor between RESET and ground sinks any stray leakage currents, holding RESET low (Figure 6). The value of the pulldown resistor is not critical; 100kΩ is large enough not to load RESET and small enough to pull RESET to ground. For applications using the MAX6413, MAX6416, and MAX6419, a 100kΩ pullup resistor between RESET and VCC will hold RESET high when VCC falls below 1V (Figure 7). Open-drain RESET versions are not recommended for applications requiring valid logic for VCC down to 0. Figure 5. MAX6414/MAX6417/MAX6420 Open-Drain RESET Output Allows use with Multiple Supplies Interfacing to Other Voltages for Logic Compatibility The open-drain outputs of the MAX6414/MAX6417/ MAX6420 can be used to interface to µPs with other logic levels. As shown in Figure 5, the open-drain output can be connected to voltages from 0 to 5.5V. This allows for easy logic compatibility to various microprocessors. Negative-Going VCC Transients In addition to issuing a reset to the µP during power-up, power-down, and brownout conditions, these supervisors are relatively immune to short-duration negative-going transients (glitches). The Maximum Transient Duration vs. Reset Threshold Overdrive graph in the Typical Operating Characteristics shows this relationship. The area below the curve of the graph is the region in which these devices typically do not generate a reset pulse. This graph was generated using a negativegoing pulse applied to VCC, starting above the actual reset threshold (VTH) and ending below it by the magnitude indicated (reset-threshold overdrive). As the magnitude of the transient decreases (farther below the reset threshold), the maximum allowable pulse width decreases. Typically, a VCC transient that goes 100mV below the reset threshold and lasts 50µs or less will not cause a reset pulse to be issued. Ensuring a Valid RESET or RESET Down to VCC = 0 When VCC falls below 1V, RESET/RESET current sinking (sourcing) capabilities decline drastically. In the case of the MAX6412, MAX6415, and MAX6418, high8 VCC MAX6412 MAX6415 MAX6418 VCC RESET 100kΩ GND Figure 6. Ensuring RESET Valid to VCC = 0 VCC 100kΩ MAX6413 MAX6416 MAX6419 VCC RESET GND Figure 7. Ensuring RESET Valid to VCC = 0 _______________________________________________________________________________________ Low-Power, Single/Dual-Voltage µP Reset Circuits with Capacitor-Adjustable Reset Timeout Delay Chip Information TRANSISTOR COUNT: 325 PROCESS: BiCMOS MAX6412–MAX6420 Layout Consideration SRT is a precise current source. When developing the layout for the application, be careful to minimize board capacitance and leakage currents around this pin. Traces connected to SRT should be kept as short as possible. Traces carrying high-speed digital signals and traces with large voltage potentials should be routed as far from SRT as possible. Leakage current and stray capacitance (e.g., a scope probe) at this pin could cause errors in the reset timeout period. When evaluating these parts, use clean prototype boards to ensure accurate reset periods. RESET IN is a high-impedance input, which is typically driven by a high-impedance resistor-divider network (e.g., 1MΩ to 10MΩ). Minimize coupling to transient signals by keeping the connections to this input short. Any DC leakage current at RESET IN (e.g., a scope probe) causes errors in the programmed reset threshold. Table 1. Reset Voltages Suffix Table SUFFIX MIN TYP MAX 16 1.536 1.575 1.614 17 1.623 1.665 1.707 18 1.755 1.800 1.845 19 1.853 1.900 1.948 20 1.950 2.000 2.050 21 2.048 2.100 2.153 22 2.133 2.188 2.243 23 2.313 2.313 2.371 24 2.340 2.400 2.460 25 2.438 2.500 2.563 26 2.559 2.625 2.691 27 2.633 2.700 2.768 28 2.730 2.800 2.870 29 2.852 2.925 2.998 30 2.925 3.000 3.075 31 2.998 3.075 3.152 32 3.120 3.200 3.280 33 3.218 3.300 3.383 34 3.315 3.400 3.485 35 3.413 3.500 3.558 36 3.510 3.600 3.690 37 3.608 3.700 3.793 38 3.705 3.800 3.895 39 3.803 3.900 3.998 40 3.900 4.000 4.100 41 3.998 4.100 4.203 42 4.095 4.200 4.305 43 4.193 4.300 4.408 44 4.266 4.375 4.484 45 4.388 4.500 4.613 46 4.509 4.625 4.741 47 4.583 4.700 4.818 48 4.680 4.800 4.920 49 4.778 4.900 5.023 50 4.875 5.000 5.125 _______________________________________________________________________________________ 9 Low-Power, Single/Dual-Voltage µP Reset Circuits with Capacitor-Adjustable Reset Timeout Delay MAX6412–MAX6420 Standard Versions Table PART* TOP MARK MAX6412UK16-T ADVY MAX6412UK22-T ADWA MAX6412UK26-T ADWC MAX6412UK29-T ADWD MAX6412UK46-T ADWG MAX6413UK16-T ADWI MAX6413UK22-T ADWK MAX6413UK26-T ADWM MAX6413UK29-T ADWN MAX6413UK46-T ADWQ MAX6414UK16-T ADWS MAX6414UK22-T ADWU MAX6414UK26-T ADWW MAX6414UK29-T ADWX MAX6414UK46-T ADXA MAX6415UK-T ADZO MAX6416UK-T ADZP MAX6417UK-T ADZQ MAX6418UK16-T ADYG MAX6418UK22-T ADYI MAX6418UK26-T ADYK MAX6418UK29-T ADYL MAX6418UK46-T ADYO MAX6419UK16-T ADYQ MAX6419UK22-T ADYS MAX6419UK26-T ADYU MAX6419UK29-T ADYV MAX6419UK46-T ADYY MAX6420UK16-T ADZA MAX6420UK22-T ADZC MAX6420UK26-T ADZE MAX6420UK29-T ADZF MAX6420UK46-T ADZI *Sample Stock is generally held on all standard versions. Contact factory for availability of nonstandard versions. 10 ______________________________________________________________________________________ Low-Power, Single/Dual-Voltage µP Reset Circuits with Capacitor-Adjustable Reset Timeout Delay PART FIXED VTH MANUAL RESET RESET IN MAX6412 ✔ ✔ MAX6413 ✔ ✔ PUSH-PULL RESET PUSH-PULL RESET OPEN-DRAIN RESET — ✔ — — — — ✔ — MAX6414 ✔ ✔ — — — ✔ MAX6415 — — ✔ ✔ — — MAX6416 — — ✔ — ✔ — MAX6417 — — ✔ — — ✔ MAX6418 ✔ — ✔ ✔ — — MAX6419 ✔ — ✔ — ✔ — MAX6420 ✔ — ✔ — — ✔ Typical Operating Circuit VCC VCC RESET/RESET MR GND RESET/RESET µP MAX6412 MAX6413 MAX6414 SRT ______________________________________________________________________________________ 11 MAX6412–MAX6420 Selector Guide Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) SOT-23 5L .EPS MAX6412–MAX6420 Low-Power, Single/Dual-Voltage µP Reset Circuits with Capacitor-Adjustable Reset Timeout Delay PACKAGE OUTLINE, SOT-23, 5L 21-0057 E 1 1 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2003 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.