30 MHz to 1000 MHz 75 Ω Gain Block ADL5533 Preliminary Technical Data FEATURES Fixed gain of 20 dB Operation up to 1000 MHz +37.3 dBm OIP3 at 70 MHz Noise Figure 2.9 dB at 70 MHz Input/output internally matched to 75 Ω Temperature and power supply stable Power supply: 5 V Power supply current: 66 mA 1000 V ESD (Class 1C) FUNCTIONAL BLOCK DIAGRAM 8 NC NC 1 RFIN 2 7 RFOUT NC 3 NC 4 6 NC ADL5533 5 CLIN Figure 1. Block Diagram GENERAL DESCRIPTION The ADL5533 is a fixed-gain, linear amplifier that operates at frequencies up to 1000 MHz. Intended for use in a wide variety of applications, including broadband, CATV, cable modem and FTTH. coupling capacitors, a power supply decoupling capacitor and external inductor are required for operation. The fixed gain of 20 dB is stable over frequency, temperature, power supply and from device to device. OIP3 is +37.3 dBm with an output compression point of +18.8 dBm and a noise figure of 2.9 dB. The ADL5533, fabricated on a GaAs HBT process, and has an ESD rating of 1000 V (Class 1C).The device is packaged in a 3mm x 3mm LFCSP that uses an exposed paddle for excellent thermal impedance and operates from −40°C to +85°C. A fully populated evaluation board is available. The ADL5533 is single-ended and internally matched to 75 Ω with an input return loss of 10 dB. Only input/output ac- This amplifier operates with a supply voltage of +5V, consuming 66 mA of supply current. Rev. PrC 5/07 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2007 Analog Devices, Inc. All rights reserved. ADL5533 Preliminary Technical Data TABLE OF CONTENTS Features .............................................................................................. 1 ESD Caution...................................................................................4 Functional Block Diagram .............................................................. 1 Pin Configuration and Function Descriptions..............................5 General Description ......................................................................... 1 Typical Performance Characteristics ..............................................6 Revision History ............................................................................... 2 Evaluation Board ...............................................................................7 Specifications..................................................................................... 3 Outline Dimensions ..........................................................................9 Absolute Maximum Ratings............................................................ 4 Ordering Guide .............................................................................9 REVISION HISTORY 5/07—Rev. PrC: Preliminary Version Rev. PrC 5/07 | Page 2 of 9 Preliminary Technical Data ADL5533 SPECIFICATIONS VCC = 5 V, T = 25°C, unless otherwise noted. Table 1. Parameter OVERALL FUNCTION Frequency Range Gain vs. Frequency Input Return Loss (S11) Output Return Loss (S22) FREQUENCY = 70 MHz Gain vs. Temperature Output 1 dB Compression Point Output Third-Order Intercept Output Second Order Intercept Noise Figure FREQUENCY = 380 MHz Gain vs. Temperature Output 1 dB Compression Point Output Third-Order Intercept Output Second Order Intercept Noise Figure FREQUENCY = 820 MHz Gain vs. Temperature Output 1 dB Compression Point Output Third-Order Intercept Output Second Order Intercept Noise Figure POWER INTERFACE Supply Voltage Supply Current vs. Temperature Power Dissipation Conditions Min Typ Max Unit 1000 ±0.25 -10 -10 MHz dB dB dB 19.8 ±.25 18.7 37.3 TBD 2.9 dB dB dBm dBm dBm dB 18.6 ±.25 18.8 35.7 TBD 3.1 dB dB dBm dBm dBm dB 16.8 ±.25 18.3 34.5 TBD 3.2 dB dB dBm dBm dBm dB 30 ± 50 MHz. Center Frequency = 190 MHz or 380 MHz 50 MHz to 750 MHz 50 MHz to 750 MHz −40°C ≤ TA ≤ +85°C ∆f = 1 MHz, Output Power (POUT) = 0 dBm (per tone) ∆f = 1 MHz, Output Power (POUT) = 0 dBm (per tone) −40°C ≤ TA ≤ +85°C ∆f = 1 MHz, Output Power (POUT) = 0 dBm (per tone) ∆f = 1 MHz, Output Power (POUT) = 0 dBm (per tone) −40°C ≤ TA ≤ +85°C ∆f = 1 MHz, Output Power (POUT) = 0 dBm (per tone) ∆f = 1 MHz, Output Power (POUT) = 0 dBm (per tone) Pins RFOUT,Vcc 4.75 −40°C ≤ TA ≤ +85°C VPOS = 5V Rev. PrC 5/07 | Page 3 of 9 5 66 75 330 5.25 V mA mA mW ADL5533 Preliminary Technical Data ABSOLUTE MAXIMUM RATINGS Table 2. Parameter Supply Voltage, VPOS Input Power (re: 75 Ω) Internal Power Dissipation (Paddle Soldered) θJA (Paddle Soldered) Maximum Junction Temperature Operating Temperature Range Storage Temperature Range (Soldering 60 sec) Rating 5.5 V +12 dBm 650 mW TBD °C/W TBD °C −40°C to +85°C −65°C to +150°C 240°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION Rev. PrC 5/07 | Page 4 of 9 Preliminary Technical Data ADL5533 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS NC1 PIN 1 INDICATOR RFIN 2 ADL5533 NC 3 TOP VIEW (Not to Scale) NC 4 8 NC 7 RFOUT 6 NC 5 CLIN Figure 2. Pin Configuration Table 3. Pin Function Descriptions Single Pin No. 2 7 1, 3, 4, 6, 8 5 Mnemonic Description RFIN RFOUT RF Input: Requires a DC blocking capacitor. RF Output and Bias: DC bias is provided to this pin through an inductor. RF path requires a DC blocking capacitor. No Connect NC CLIN Exposed Paddle A 10 nF capacitor connected between pin 5 and ground provides decoupling for the on board linearizer. Internally connected to GND. Solder to a low impedance ground plane Rev. PrC 5/07 | Page 5 of 9 ADL5533 Preliminary Technical Data TYPICAL PERFORMANCE CHARACTERISTICS 40.0 -5 35.0 ReturnLoss & Isolation (dB) NF,GAIN, P1dB, OIP3 (dB, dBm) -10 30.0 25.0 20.0 15.0 NF GAIN P1dB OIP3 10.0 -15 -20 -25 S11 S12 S22 -30 5.0 0.0 -35 50 150 250 350 450 550 650 750 850 950 1050 30 Frequency (MHz) 40 38 36 OIP3 (dBm) 34 32 70 MHz 190 MHz 380 MHz 26 500 MHz 820 MHz 24 1000 MHz 22 20 -6 -4 -2 0 2 4 6 8 10 330 430 530 630 730 830 930 1030 Figure 5 ADL5533 Input / Output Return Loss and Reverse Isolation vs Frequency 42 28 230 Frequency (MHz) Figure 3 ADL5533 Gain, Noise Figure, OIP3 and P1dB vs Frequency 30 130 12 14 16 18 20 Pout (dBm) Figure 4 ADL5534 OIP3 vs Pout and Frequency Rev. PrC 5/07 | Page 6 of 9 Preliminary Technical Data ADL5533 EVALUATION BOARD Figure 6 shows the schematic for the ADL, 5533 evaluation board. The board is powered by a single 5 V supply. The components used on the board are listed in. Table 4 Power can be applied to the board through clip-on leads (Vcc, Gnd), or through Jumper W1. VCC Testloop Red C6 open RFIN C1 10 nF C4 10 nF L1 470 nH 1 NC NC 2 RFin RFout 7 ADL5533 NC 6 4 NC Clin 5 GND Testloop Black L2 6.8 nH 8 3 NC W1 C5 1 uF C2 10 nF RFOUT C7 Open C3 100 nF Figure 6. Evaluation Board Schematic Table 4. Evaluation Board Configuration Options Component C1, C2 C3, C4, C5 Function AC-coupling capacitors. Compensates for internal non linearities Power Supply decoupling capacitors capacitor. C6, C7 L1 L2 VCC & GND DC bias inductor. Output matching element. Clip-on terminals for power supply. RFIN, RFOUT W1 RF input and output interface 2-pin jumper for connection of ground and supply via cable. Rev. PrC 5/07 | Page 7 of 9 Default Value 10 nF 0402 C3 100 nF 0603 C4 10 nF 0603 C5 1uF 0603 Open 0603 470 nH L0603 6.8 nH L0603 VCC Red GND Black 75 ohm “F” type connectors ADL5533 Preliminary Technical Data Figure 8.Evaluation Board Layout (Bottom) Figure 7. Evaluation Board Layout (Top) Rev. PrC 5/07 | Page 8 of 9 Preliminary Technical Data ADL5533 OUTLINE DIMENSIONS 3.25 3.00 SQ 2.75 0.60 MAX 0.50 BSC TOP VIEW PIN 1 INDICATOR 2.95 2.75 SQ 2.55 0.90 MAX 0.85 NOM PIN 1 INDICATOR 1 8 1.89 1.74 1.59 EXPOSED PAD (BOTTOM VIEW) 0.30 0.23 0.18 12° MAX 0.50 0.40 0.30 5 0.70 MAX 0.65 TYP 4 1.60 1.45 1.30 022107-A 0.05 MAX 0.01 NOM 0.20 REF Figure 9. 8-Lead Lead Frame Chip Scale Package [LFCSP_VD] 3mm × 3 mm Body, Very Thin, Dual Lead CP-8-2 Dimensions shown in millimeters ORDERING GUIDE Model ADL5533ACPZ-R7 Temperature Range 1 ADL5533ACPZ-WP1 ADL5533-EVALZ 1 Package Description Package Option −40°C to +85°C 8-Lead LFCSP Tape and Reel CP-8-2 −40°C to +85°C 8-Lead LFCSP Waffle Pack CP-8-2 Evaluation Board Z = Pb-free part. ©2007 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. PR06835-0-5/07(PrC) Rev. PrC 5/07 | Page 9 of 9 Branding Ordering Quantity