SANYO LA7840

Ordering number: EN5147B
Monolithic Linear IC
LA7840
Vertical Deflection Output Circuit
Package Dimensions
Overview
The LA7840 is a vertical deflection output IC for TVs and
CRT displays with excellent image quality that use a BUS
control system signal processing IC. This IC can drive the
direct (even including a DC component) deflection yoke with
the sawtooth wave output from the BUS control system signal
processing IC. When used in conjunction with Sanyo’s LA7615
series of BUS control system signal processing ICs for TVs,
this IC can process all color television signal system functions
through the BUS system. Because the maximum deflection
current is 1.8 Ap-p, the LA7840 is suited for small and
medium screen sets.
unit : mm
3075-SIP7H
[LA7840]
Features
. Low power dissipation due to built-in pump-up circuit
. Vertical output circuit
. Thermal protection circuit built in
. Excellent crossover characteristics
. DC coupling possible
SANYO : SIP7H
Specifications
Maximum Ratings at Ta = 25 °C
Parameter
Symbol
Conditions
Ratings
Unit
Maximum supply voltage
VCC6 max
34
Output block supply voltage
VCC3 max
70
Deflection output current
Thermal resistance
Allowable power dissipation
I 2 max
–1.5 to +1.5
θj-c
Pd max
4.0
With arbitrarily large heat sink
9
V
V
Ap-o
°C/W
W
Operating temperature
Topr
–20 to +85
°C
Storage temperature
Tstg
–40 to +150
°C
Ratings
Unit
Operating Conditions at Ta = 25 °C
Parameter
Symbol
Recommended supply voltage
VCC6
Operating supply voltage range
VCC6 op
Recommended deflection output current
I 2 p-p
Conditions
24
16 to 33
to 1.8
V
V
Ap-p
SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN
D1096HA(II)/61595HA(II) No.5147-1/4
LA7840
Operating Characteristics at Ta = 25 °C, VCC6 = 24 V
Parameter
Pump-up charge saturation
voltage
Pump-up discharge saturation
voltage
Deflection output saturation
voltage (lower)
Deflection output saturation
voltage (upper)
Idling current
Midpoint voltage
Symbol
Conditions
min
typ
max
Unit
VS7-1
I 7 = 20 mA
1.8
V
VS6-7
I 7 = –0.9 A
3.0
V
VS2-1
I 2 = 0.9 A
1.3
V
VS3-2
I 2 = –0.9 A
3.2
V
65
13.0
mA
V
IDL
VMID
35
11.0
12.0
Block Diagram
Sample Application Circuit
(Single power supply)
No.5147-2/4
LA7840
Sample Application Circuit
(Double power supply)
Sample Application Circuit
Unit (resistance: Ω, capacitance: F)
No.5147-3/4
LA7840
No products described or contained herein are intended for use in surgical implants, life-support systems,
aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like,
the failure of which may directly or indirectly cause injury, death or property loss.
Anyone purchasing any products described or contained herein for an above-mentioned use shall:
1 Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and
distributors and all their officers and employees, jointly and severally, against any and all claims and litigation
and all damages, cost and expenses associated with such use:
2 Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on
SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees
jointly or severally.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for
volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or
implied regarding its use or any infringements of intellectual property rights or other rights of third parties.
This catalog provides information as of December, 1996. Specifications and information herein are subject to change without notice.
No.5147-4/4