Ordering number: EN 1707B Thick Film Hybrid IC STK4036II AF Power Amplifier (Split Power Supply) (50W min, THD = 0.4%) Features Package Dimensions • Compact package for thin-type audio sets • Member of pin-compatible series with outputs of 20 to 200W • Easy heatsink design to disperse heat generated in thintype stereo sets • Constant-current circuit to reduce supply switch-on and switch-off shock noise • External supply switch-on and switch-off shock noise muting, load short-circuit protection, thermal shutdown and other circuits can be tailor-designed. unit: mm 4033 [STK4036II] Specifications Maximum Ratings at Ta = 25°C Parameter Maximum supply voltage Thermal resistance Junction temperature Operating substrate temperature Storage temperature Symbol Conditions Unit ±52 V θj-c 1.8 °C/W Tj 150 °C Tc Tstg Available time for load short-circuit1 Ratings VCC max ts VCC = ±35V, RL = 8Ω, f = 50Hz, PO = 50W 125 °C −30 to +125 °C 2 s Recommended Operating Conditions at Ta = 25°C Parameter Symbol Conditions Ratings Unit Recommended supply voltage VCC ±35 V Load resistance RL 8 Ω SANYO Electric Co., Ltd. Semiconductor Business Headquarters TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN 60697HA (ID) / 32596HA (ID) / 8298MO / 1075MY, TS No. 1707—1/3 STK4036II Operating Characteristics at Ta = 25°C, VCC = ±35V, RL = 8Ω (noninductive load), Rg = 600Ω, VG = 40dB Parameter Quiescent current Symbol max Unit ICCO VCC = ±42V 10 20 50 mA PO(1) THD = 0.4%, f = 20Hz to 20kHz 50 – – W PO(2) VCC = ±31V, THD = 1.0%, RL = 4Ω, f = 1kHz 55 – – W THD PO = 1.0W, f = 1kHz – – 0.3 % – 20 to 50k – Hz – 55 – kΩ – – 1.2 mVrms −70 0 +70 mV Output power Total harmonic distortion Frequency response Input impedance fL, fH ri Conditions PO = 1.0W, +0 −3 dB PO = 1.0W, f = 1kHz Output noise voltage2 VNO VCC = ±42V, Rg = 10kΩ Neutral voltage VN VCC = ±42V min typ Notes. All tests are measured using a constant-voltage supply unless otherwise specified. 1. Output noise voltage is measured using the transformer supply specified below. 2. The output noise voltage is the peak value of an average-reading meter with an rms value scale. The noise voltage waveform does not inlcude any pulse noise. Specified Transformer Supply (MG-200 or Equivalent) Equivalent Circuit No. 1707—2/3 STK4036II Sample Application Circuit (50W min AF Power Amplifier) ■ ■ No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or indirectly cause injury, death or property loss. Anyone purchasing any products described or contained herein for an above-mentioned use shall: Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and expenses associated with such use: ➁ Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees, jointly or severally. ➀ ■ Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of June, 1997. Specifications and information herein are subject to change without notice. No. 1707—3/3