Ordering number : EN4593A Thick Film Hybrid IC STK4048V 150 W min AF Power Amplifier (Split Power Supply) Features Package Dimensions • Compact packaging supports slimmer set designs • Series designed from 20 up to 100 W (200 W) and pincompatibility (120 to 200 W have 18 pins) • Simpler heat sink design facilitates thermal design of slim stereo sets • Current mirror circuit application reduce distortion to 0.08 % • Supports addition of electronic circuits for thermal shutdown and load-short protection circuit as well as pop noise muting which occurs when the power supply switch is turned on and off. unit: mm 4051A [STK4048V] Specifications Maximum Ratings at Ta = 25°C Parameter Maximum supply voltage Symbol Condition Rating Unit VCC max ± 87 V θj-c 1.2 °C/W Junction temperature Tj 150 °C Operating substrate temperature Tc 125 °C –30 to +125 °C Rating Unit Thermal resistance Storage temperature Tstg Recommended Operational Conditions at Ta = 25°C Parameter Recommended supply voltage Load resistance Symbol VCC RL Condition ± 60 V 8 Ω SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN 61096HA (OT)/O2093YO (OT) No. 4593-1/3 STK4048V Operating Characteristics at Ta = 25°C, VCC = ± 60 V, RL = 8 Ω, VG = 40 dB, Rg = 600 Ω, 100 k LPF ON, RL (non-inductive load) Rating Parameter Quiescent current Output power Total harmonic distortion Frequency response Input resistance Output noise voltage Neutral voltage Symbol ICCO PO Condition VCC = ± 72 V THD = 0.08 %, f = 20 Hz to 20 kHz THD PO = 1.0 W, f = 1 kHz fL, fH +0 PO = 1.0 W, dB –3 ri VNO VN min typ max 15 120 150 20 to 50k –70 0 % Hz 55 VCC = ± 72 V, Rg = 10 kΩ VCC = ± 72 V mA W 0.08 PO = 1.0 W, f = 1 kHz Unit kΩ 1.2 mVrms + 70 mV Note: Use a constant-voltage power supply as the test power supply unless otherwise specified * The output noise voltage is the peak value measured with an averaging rms scale volt meter. The noise voltage waveform should not include pulse noise. Specified Transformer Power Supply (MG-250 Equivalent) Equivalent Circuit No. 4593-2/3 STK4048V Application Circuit: 150W min Single Channel AF Power Amplifier ■ No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or indirectly cause injury, death or property loss. ■ Anyone purchasing any products described or contained herein for an above-mentioned use shall: ➀ Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and expenses associated with such use: ➁ Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally. ■ Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of November, 1997. Specifications and information herein are subject to change without notice. No. 4593-3/3