Order this document by MC12148/D The MC12148 requires an external parallel tank circuit consisting of the inductor (L) and capacitor (C). A varactor diode may be incorporated into the tank circuit to provide a voltage variable input for the oscillator (VCO). This device may also be used in many other applications requiring a fixed frequency clock. The MC12148 is ideal in applications requiring a local oscillator. Systems include electronic test equipment and digital high–speed telecommunications. The MC12148 is based on the VCO circuit topology of the MC1648. The MC12148 has been realized utilizing Motorola’s MOSAIC III advanced bipolar process technology which results in a design which can operate at a much higher frequency than the MC1648 while utilizing half the current. Please consult with the MC1648 data sheet for additional background information. The ECL output circuitry of the MC12148 is not a traditional open emitter output structure and instead has an on–chip termination resistor with a nominal value of 500 ohms. This facilitates direct ac–coupling of the output signal into a transmission line. Because of this output configuration, an external pull–down resistor is not required to provide the output with a dc current path. This output is intended to drive one ECL load. If the user needs to fanout the signal, an ECL buffer such as the MC10EL16 Line Receiver/Driver should be used. LOW POWER VOLTAGE CONTROLLED OSCILLATOR SEMICONDUCTOR TECHNICAL DATA 8 1 D SUFFIX PLASTIC PACKAGE CASE 751 (SO–8) NOTE: The MC12148 is NOT useable as a crystal oscillator. • • • • 8 1 Typical Operating Frequency Up to 1100 MHz SD SUFFIX PLASTIC PACKAGE CASE 940 (SSOP–8) Low–Power 20 mA at 5.0 Vdc Power Supply 8–Pin SOIC Package Phase Noise –90 dBc/Hz at 25 kHz Typical PIN CONNECTIONS GND VCCO BLOCK DIAGRAM 8 (Typical Test Circuit) VCCO 0.01µF 0.1µF 100µF 7 Out GND 6 5 1200Ω* Fout 8 7 6 GND VCCO Out VCC = 4.5 to 5.5 V 0.01µF 0.1µF VCC 1 5 GND * The 1200 Ω resistor and the scope termination impedance constitute a 25:1 attenuator probe. AGC TANK Vref 2 3 4 0.1 µF 51KΩ 3 TANK 4 Vref ORDERING INFORMATION Device Vin 2 AGC (Top View) 0.1µF 100 µF 1 VCC MC12148D MC12148SD Operating Temperature Range TA = – 40° to +85°C Motorola, Inc. 1997 Package SO–8 SSOP–8 Rev 5 MC12148 MAXIMUM RATINGS Parameter Power Supply Voltage, Pins 1, 7 Operating Temperature Range Storage Temperature Range NOTE: Symbol Value Unit VCC –0.5 to 7.0 Vdc TA –40 to 85 °C Tstg –65 to 150 °C ESD data available upon request. ELECTRICAL CHARACTERISTICS (VCC = 5.0 V; TA = –40 to 85°C, unless otherwise noted.) Symbol Min Typ Max Unit Supply Current ICC – 19 25 mA Output Level HIGH (1.0 MΩ Impedance) VOH 3.95 4.17 4.61 V Output Level LOW (1.0 MΩ Impedance) VOL 3.04 3.41 3.60 V – –90 – dBc/Hz – –120 – dBc/Hz Characteristic CSR @ 1.0 MHz Offset, 1.0 Hz BW L(f) L(f) SNR (Signal to Noise Ratio from Carrier) SNR – 40 – dB Supply Drift Fsts – 3.6 – KHz/mV Thermal Drift Fstt – 0.1 – KHz/°C H2 – –25 – dBc CSR @ 25 kHz Offset, 1.0 Hz BW Frequency Stability Second Harmonic (from Carrier) Figure 1. Circuit Schematic VCC 1 VCCO 7 Q9 Q1 Q3 Q2 6 OUT Q4 Q11 Q10 Q7 Q6 D1 Q5 Q8 D2 510Ω 8 GND 2 4 Vref 3 TANK 5 GND 2 AGC MOTOROLA RF/IF DEVICE DATA MC12148 Figure 2. Typical Evaluation Results (CSR MC12148 5.0 Vdc; VCC @ 25°C; 930 MHz CW) 0 –20 dBc/Hz –40 –60 –80 –100 –120 –140 1K 10K 100K 1M 10M 100M L (f) [dBc/Hz] versus f [Hz] Tank Component Suppliers Below are suppliers who manufacture tuning varactors and inductors which can be used to build an external tank circuit. Motorola has used these varactors and inductors for evaluation purposes, however, there are other vendors who manufacture similar products. Coilcraft Inductors A01T thru A05T Coilcraft–Coilcraft, Inc. 1102 Silver Lake Rd. Gary, Illinois 60013 708–639–6400 Loral Tuning Varactors GC1500 Series Loral 16 Maple Road Chelmsford, Massachusetts 01824 508–256–8101 or 508–256–4113 Alpha Tuning Diodes DVH6730 Series Alpha Semiconductor Devices Division 20 Sylvan Road Woburn, MA 01801 617–935–5150 * At 1.1 GHz, use a Coilcraft A0IT Springair coil at 2.5 nH and a Loral Varactor 3.0 to 8.0 pF at VIN = 1.0 to 5.0 V. MOTOROLA RF/IF DEVICE DATA 3 MC12148 OUTLINE DIMENSIONS D SUFFIX PLASTIC PACKAGE CASE 751–06 (SO–8) ISSUE T D A NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS ARE IN MILLIMETER. 3. DIMENSION D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS OF THE B DIMENSION AT MAXIMUM MATERIAL CONDITION. C 8 5 0.25 H E B M M 1 4 h B X 45 _ q e DIM A A1 B C D E e H h L A C SEATING PLANE L 0.10 A1 B 0.25 C B M A S S q MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.35 0.49 0.19 0.25 4.80 5.00 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.25 0_ 7_ SD SUFFIX PLASTIC PACKAGE CASE 940-03 (SSOP–8) ISSUE B 8X K REF 0.12 (0.005) 0.25 (0.010) M T U S V N S M 8 L/2 N 5 F B L DETAIL E PIN 1 IDENT 1 4 ÉÉÉÉ ÇÇÇÇ ÇÇÇÇ ÉÉÉÉ K –U– A –V– 0.20 (0.008) M T U J J1 K1 S SECTION N–N 0.076 (0.003) –T– SEATING PLANE –W– C D G 4 H DETAIL E NOTES: 1 DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2 CONTROLLING DIMENSION: MILLIMETER. 3 DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4 DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 5 DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION/INTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN EXCESS OF K DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR INTRUSION SHALL NOT REDUCE DIMENSION K BY MORE THAN 0.07 (0.002) AT LEAST MATERIAL CONDITION. 6 TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7 DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE –W–. DIM A B C D F G H J J1 K K1 L M MILLIMETERS MIN MAX 2.87 3.13 5.20 5.38 1.73 1.99 0.05 0.21 0.63 0.95 0.65 BSC 0.44 0.60 0.09 0.20 0.09 0.16 0.25 0.38 0.25 0.33 7.65 7.90 0_ 8_ INCHES MIN MAX 0.113 0.123 0.205 0.212 0.068 0.078 0.002 0.008 0.024 0.037 0.026 BSC 0.017 0.023 0.003 0.008 0.003 0.006 0.010 0.015 0.010 0.013 0.301 0.311 0_ 8_ MOTOROLA RF/IF DEVICE DATA MC12148 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 1–303–675–2140 or 1–800–441–2447 JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 141, 4–32–1 Nishi–Gotanda, Shagawa–ku, Tokyo, Japan. 03–5487–8488 Customer Focus Center: 1–800–521–6274 Mfax: [email protected] – TOUCHTONE 1–602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, Motorola Fax Back System – US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 – http://sps.motorola.com/mfax/ HOME PAGE: http://motorola.com/sps/ MOTOROLA RF/IF DEVICE DATA◊ MC12148/D 5