Order this document by MC12052A/D The MC12052A is a super low power dual modulus prescaler used in phase–locked loop applications. Motorola’s advanced Bipolar MOSAIC V technology is utilized to achieve low power dissipation of 2.7 mW at a minimum supply voltage of 2.7 V. The MC12052A can be used with CMOS synthesizers requiring positive edges to trigger internal counters such as Motorola’s MC145XXX series in a PLL to provide tuning signals up to 1.1 GHz in programmable frequency steps. A Divide Ratio Control (SW) permits selection of a 64/65 or 128/129 divide ratio as desired. The Modulus Control (MC) selects the proper divide number after SW has been biased to select the desired divide ratio. • 1.1 GHz Toggle Frequency • • • • • • MECL PLL COMPONENTS ÷64/65, ÷128/129 LOW POWER DUAL MODULUS PRESCALER SEMICONDUCTOR TECHNICAL DATA 8 1 The MC12052 is Pin and Functionally Compatible with the MC12022 Low Power 1.0 mA Typical D SUFFIX PLASTIC PACKAGE CASE 751 (SO–8) 2.0 mA Maximum, –40 to 85°C, VCC = 2.7 to 5.5 Vdc Short Setup Time (tset) 16 ns Maximum @ 1.1 GHz Modulus Control Input Level is Compatible with Standard CMOS and TTL Maximum Input Voltage Should Be Limited to 6.5 Vdc 8 MOSAIC V is a trademark of Motorola 1 SD SUFFIX PLASTIC PACKAGE CASE 940 (SSOP–8) FUNCTIONAL TABLE SW MC Divide Ratio H H 64 H L 65 L H 128 L L 129 PIN CONNECTIONS NOTES: 1. SW: H = VCC, L = Open. A logic L can also be applied by grounding this pin, but this is not recommended due to increased power consumption. 2. MC: H = 2.0 V to VCC, L = GND to 0.8 V. IN VCC SW OUT MAXIMUM RATINGS Characteristic Power Supply Voltage, Pin 2 Symbol Range Unit VCC –0.5 to 7.0 Vdc TA –40 to 85 °C Storage Temperature Range Tstg –65 to 150 °C Modulus Control Input, Pin 6 MC –0.5 to 6.5 Vdc Operating Temperature Range 1 8 2 7 3 6 4 5 IN NC MC Gnd (Top View) ORDERING INFORMATION Device MC12052AD MC12052ASD Motorola, Inc. 1997 Operating Temp Range Package TA = – 40° to +85°C SSOP–8 SO–8 Rev 3 MC12052A ELECTRICAL CHARACTERISTICS (VCC = 2.7 to 5.5 VDC, TA = –40 to 85°C, unless otherwise noted.) Symbol Min Typ Max Unit ft 0.1 1.4 1.1 GHz ICC VIH1 VIL1 – 1.0 2.0 mA 2.0 – V Gnd – VCC + 0.5 V 0.8 VIH2 VIL2 VCC – 0.5 V Open VCC Open VCC + 0.5 V Open VDC Output Voltage Swing (Note 2) (CL = 8.0 pF, RL = 3.3 kΩ) Vout 0.8 1.1 – VPP Modulus Setup Time MC to Out @ 1100 MHz tset Vin – 11 16 ns 100 400 – – 1000 1000 mVPP – – 0.5 0.5 3.0 3.0 Characteristic Toggle Frequency (Sine Wave Input) Supply Current (Pin 2) Modulus Control Input High (MC) Modulus Control Input Low (MC) Divide Ratio Control Input High (SW) Divide Ratio Control Input Low (SW) Input Voltage Sensitivity 250–1100 MHz 100–250 MHz Output Current (Note 1) VCC = 2.7 V, CL = 8.0 pF, RL = 3.3 kΩ VCC = 5.0 V, CL = 8.0 pF, RL = 7.2 kΩ V – IO mA NOTES: 1. Divide ratio of ÷64/65 @ 1.1 GHz 2. Valid over voltage range 2.7 to 5.5 V; RL = 3.3 kΩ @ VCC = 2.7 V; RL = 7.2 kΩ @ VCC = 5.0 V Figure 1. Logic Diagram (MC12052A) D Q D D Q B A Figure 2. Modulus Setup Time Q Prop. Delay C In QB C QB C C M QB In In Out MC MC Setup D Q D QB C D C QB D E Q D QB C F Q C QB D G H C S Q Q MC QB MC Release Out Modulus setup time MC to out is the MC setup or MC release plus the prop delay. SW Figure 3. AC Test Circuit VCC = 2.7 to 5.5 V C3 Sine Wave Generator C1 VCC 50 Ω OUT C2 CL IN RL MC MC Input 2 SW IN GND EXTERNAL COMPONENTS C1 = C2 = 1000 pF C3 = 0.1 µF CL = 8.0pF (Including Scope and jig capacitance) RL = 3.3 kΩ @ VCC = 2.7 V RL = 7.2 kΩ @ VCC = 5.0 V MOTOROLA RF/IF DEVICE DATA MC12052A Figure 4. Typical Input Impedance versus Input Frequency 300 200 R 100 MHz 0 –100 –200 OHMS –300 –400 –500 –600 –700 –800 jX –900 –1000 –1100 –1200 100 MOTOROLA RF/IF DEVICE DATA 200 300 400 500 600 700 800 900 1000 1100 1200 3 MC12052A OUTLINE DIMENSIONS D SUFFIX PLASTIC PACKAGE CASE 751–06 (SO–8) ISSUE T D A NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS ARE IN MILLIMETER. 3. DIMENSION D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS OF THE B DIMENSION AT MAXIMUM MATERIAL CONDITION. C 8 5 0.25 H E M B M 1 4 X 45 _ h B q e A C SEATING PLANE L 0.10 A1 B 0.25 M C B S A DIM A A1 B C D E e H h L q S MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.35 0.49 0.19 0.25 4.80 5.00 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.25 0_ 7_ SD SUFFIX PLASTIC PACKAGE CASE 940–03 (SSOP–8) ISSUE B 8X 8 L/2 K REF 0.12 (0.005) 0.25 (0.010) M T U S V S N M 5 N F B L PIN 1 IDENT DETAIL E 1 4 ÉÉÉÉ ÇÇÇÇ ÇÇÇÇ ÉÉÉÉ K –U– A –V– 0.20 (0.008) M J T U S J1 K1 NOTES: 1 DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2 CONTROLLING DIMENSION: MILLIMETER. 3 DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4 DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 5 DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION/INTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN EXCESS OF K DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR INTRUSION SHALL NOT REDUCE DIMENSION K BY MORE THAN 0.07 (0.002) AT LEAST MATERIAL CONDITION. 6 TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7 DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE –W–. SECTION N–N –W– 0.076 (0.003) –T– SEATING PLANE C D DETAIL E G 4 H DIM A B C D F G H J J1 K K1 L M MILLIMETERS MIN MAX 2.87 3.13 5.20 5.38 1.73 1.99 0.05 0.21 0.63 0.95 0.65 BSC 0.44 0.60 0.09 0.20 0.09 0.16 0.25 0.38 0.25 0.33 7.65 7.90 0_ 8_ INCHES MIN MAX 0.113 0.123 0.205 0.212 0.068 0.078 0.002 0.008 0.024 0.037 0.026 BSC 0.017 0.023 0.003 0.008 0.003 0.006 0.010 0.015 0.010 0.013 0.301 0.311 0_ 8_ MOTOROLA RF/IF DEVICE DATA MC12052A Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. MOTOROLA RF/IF DEVICE DATA 5 MC12052A Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 1–303–675–2140 or 1–800–441–2447 JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 141, 4–32–1 Nishi–Gotanda, Shagawa–ku, Tokyo, Japan. 03–5487–8488 Customer Focus Center: 1–800–521–6274 Mfax: [email protected] – TOUCHTONE 1–602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, Motorola Fax Back System – US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 – http://sps.motorola.com/mfax/ HOME PAGE: http://motorola.com/sps/ 6 ◊ MC12052A/D MOTOROLA RF/IF DEVICE DATA