AD ADN4696E

3.3 V, 100 Mbps, Half- and Full-Duplex,
High Speed M-LVDS Transceivers
ADN4690E/ADN4692E/ADN4694E/ADN4695E
FEATURES
FUNCTIONAL BLOCK DIAGRAMS
Multipoint LVDS transceivers (low voltage differential
signaling driver and receiver pairs)
Switching rate: 100 Mbps (50 MHz)
Supported bus loads: 30 Ω to 55 Ω
Choice of 2 receiver types
Type 1 (ADN4690E/ADN4692E): hysteresis of 25 mV
Type 2 (ADN4694E/ADN4695E): threshold offset of 100 mV
for open-circuit and bus-idle fail-safe
Conforms to TIA/EIA-899 standard for M-LVDS
Glitch-free power-up/power-down on M-LVDS bus
Controlled transition times on driver output
Common-mode range: −1 V to +3.4 V, allowing
communication with 2 V of ground noise
Driver outputs high-Z when disabled or powered off
Enhanced ESD protection on bus pins
±15 kV HBM (human body model), air discharge
±8 kV HBM (human body model), contact discharge
±10 kV IEC 61000-4-2, air discharge
±8 kV IEC 61000-4-2, contact discharge
Operating temperature range: −40°C to +85°C
Available in 8-lead (ADN4690E/ADN4694E) and 14-lead
(ADN4692E/ADN4695E) SOIC packages
VCC
ADN4690E/
ADN4694E
RO
R
RE
A
B
DE
D
10471-001
DI
GND
Figure 1.
VCC
ADN4692E/
ADN4695E
RO
R
A
B
RE
DE
DI
D
GND
Z
Y
10471-102
Data Sheet
Figure 2.
APPLICATIONS
Backplane and cable multipoint data transmission
Multipoint clock distribution
Low power, high speed alternative to shorter RS-485 links
Networking and wireless base station infrastructure
GENERAL DESCRIPTION
The ADN4690E/ADN4692E/ADN4694E/ADN4695E are
multipoint, low voltage differential signaling (M-LVDS)
transceivers (driver and receiver pairs) that can operate at up
to 100 Mbps (50 MHz). Slew rate control is implemented on the
driver outputs. The receivers detect the bus state with a differential
input of as little as 50 mV over a common-mode voltage range of
−1 V to +3.4 V. ESD protection of up to ±15 kV is implemented
on the bus pins. The parts adhere to the TIA/EIA-899 standard for
M-LVDS and complement TIA/EIA-644 LVDS devices with
additional multipoint capabilities.
The ADN4690E/ADN4692E are Type 1 receivers with 25 mV of
hysteresis, so that slow-changing signals or loss of input does
not lead to output oscillations. The ADN4694E/ADN4695E are
Type 2 receivers exhibiting an offset threshold, guaranteeing the
output state when the bus is idle (bus-idle fail-safe) or the
inputs are open (open-circuit fail-safe).
The parts are available as half-duplex in an 8-lead SOIC package
(the ADN4690E/ADN4694E) or as full-duplex in a 14-lead
SOIC package (the ADN4692E/ADN4695E). A selection table
for the ADN469xE parts is shown in Table 1.
Table 1. ADN469xE Selection Table
Part No.
ADN4690E
ADN4691E
ADN4692E
ADN4693E
ADN4694E
ADN4695E
ADN4696E
ADN4697E
Receiver
Type 1
Type 1
Type 1
Type 1
Type 2
Type 2
Type 2
Type 2
Data Rate
100 Mbps
200 Mbps
100 Mbps
200 Mbps
100 Mbps
100 Mbps
200 Mbps
200 Mbps
SOIC
8-lead
8-lead
14-lead
14-lead
8-lead
14-lead
8-lead
14-lead
Duplex
Half
Half
Full
Full
Half
Full
Half
Full
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2012 Analog Devices, Inc. All rights reserved.
ADN4690E/ADN4692E/ADN4694E/ADN4695E
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Driver Voltage and Current Measurements ............................ 11
Applications ....................................................................................... 1
Driver Timing Measurements .................................................. 12
Functional Block Diagrams ............................................................. 1
Receiver Timing Measurements ............................................... 13
General Description ......................................................................... 1
Theory of Operation ...................................................................... 14
Revision History ............................................................................... 2
Half-Duplex/Full-Duplex Operation....................................... 14
Specifications..................................................................................... 3
Three-State Bus Connection ..................................................... 14
Receiver Input Threshold Test Voltages .................................... 4
Truth Tables................................................................................. 14
Timing Specifications .................................................................. 5
Glitch-Free Power-Up/Power-Down ....................................... 15
Absolute Maximum Ratings............................................................ 6
Fault Conditions ......................................................................... 15
Thermal Resistance ...................................................................... 6
Receiver Input Thresholds/Fail-Safe ........................................ 15
ESD Caution .................................................................................. 6
Applications Information .............................................................. 16
Pin Configurations and Function Descriptions ........................... 7
Outline Dimensions ....................................................................... 17
Typical Performance Characteristics ............................................. 8
Ordering Guide .......................................................................... 17
Test Circuits and Switching Characteristics ................................ 11
REVISION HISTORY
3/12—Rev. 0 to Rev. A
Added ADN4694E and ADN4695E................................. Universal
Change to Features Section, General Description Section,
and Table 1 .......................................................................................... 1
Added Type 2 Receiver Parameters, Table 2 .................................. 3
Added Table 4, Renumbered Sequentially ..................................... 5
Added Type 2 Receiver Parameters, Table 5 .................................. 5
Changes to Table 8............................................................................. 7
Added Table 13 ................................................................................ 14
Changes to Receiver Input Thresholds/Fail-Safe Section
and Figure 35.................................................................................... 15
Changes to Figure 36 and Figure 37 and Their Captions .......... 16
Changes to Ordering Guide ........................................................... 18
1/12—Revision 0: Initial Version
Rev. A | Page 2 of 20
Data Sheet
ADN4690E/ADN4692E/ADN4694E/ADN4695E
SPECIFICATIONS
VCC = 3.0 V to 3.6 V; RL = 50 Ω; TA = TMIN to TMAX, unless otherwise noted.1
Table 2.
Parameter
DRIVER
Differential Outputs
Differential Output Voltage Magnitude
∆|VOD| for Complementary Output States
Common-Mode Output Voltage (Steady State)
ΔVOC(SS) for Complementary Output States
Peak-to-Peak VOC
Maximum Steady-State Open-Circuit Output
Voltage
Voltage Overshoot
Low to High
High to Low
Output Current
Short Circuit
High Impedance State, Driver Only
Power Off
Output Capacitance
Differential Output Capacitance
Output Capacitance Balance (CY/CZ)
Logic Inputs (DI, DE)
Input High Voltage
Input Low Voltage
Input High Current
Input Low Current
RECEIVER
Differential Inputs
Differential Input Threshold Voltage
Type 1 Receiver (ADN4690E, ADN4692E)
Type 2 Receiver (ADN4694E, ADN4695E)
Input Hysteresis
Type 1 Receiver (ADN4690E, ADN4692E)
Type 2 Receiver (ADN4694E, ADN4695E)
Differential Input Voltage Magnitude
Input Capacitance
Differential Input Capacitance
Input Capacitance Balance (CA/CB)
Logic Output RO
Output High Voltage
Output Low Voltage
High Impedance Output Current
Logic Input RE
Input High Voltage
Input Low Voltage
Input High Current
Input Low Current
Symbol
Min
|VOD|
∆|VOD|
VOC(SS)
ΔVOC(SS)
VOC(PP)
VA(O), VB(O),
VY(O), or VZ(O)
480
−50
0.8
−50
Typ
0
Max
Unit
Test Conditions/Comments
650
+50
1.2
+50
150
2.4
mV
mV
V
mV
mV
V
See Figure 18
See Figure 18
See Figure 19, Figure 22
See Figure 19, Figure 22
See Figure 19, Figure 22
See Figure 20
1.2VSS
V
V
See Figure 23, Figure 26
See Figure 23, Figure 26
VPH
VPL
−0.2VSS
|IOS|
IOZ
−15
24
+10
mA
μA
IO(OFF)
−10
+10
μA
CYZ
CY/Z
pF
0.99
2.5
1.01
See Figure 21
–1.4 V ≤ (VY or VZ) ≤ 3.8 V,
other output = 1.2 V
–1.4 V ≤ (VY or VZ) ≤ 3.8 V,
other output = 1.2 V, 0 V ≤ VCC ≤ 1.5 V
VI = 0.4 sin(30e6πt) V + 0.5 V,2
other output = 1.2 V, DE = 0 V
VAB = 0.4 sin(30e6πt) V,2 DE = 0 V
VIH
VIL
IIH
IIL
2
GND
0
0
VCC
0.8
10
10
V
V
μA
μA
VIH = 2 V to VCC
VIL = GND to 0.8 V
VTH
VTH
−50
50
+50
150
mV
mV
See Table 3, Figure 35
See Table 4, Figure 35
CY or CZ
VHYS
VHYS
|VID|
CA or CB
CAB
CA/B
3
pF
25
0
0.05
VCC
3
0.99
2.5
1.01
VOH
VOL
IOZ
2.4
−10
0.4
+15
VIH
VIL
IIH
IIL
2
GND
−10
−10
VCC
0.8
0
0
Rev. A | Page 3 of 20
mV
mV
V
pF
pF
VI = 0.4 sin(30e6πt) V + 0.5 V,2
other input = 1.2 V
VAB = 0.4 sin(30e6πt) V2
V
V
μA
IOH = –8 mA
IOL = 8 mA
VO = 0 V or 3.6 V
V
V
μA
μA
VIH = 2 V to VCC
VIL = GND to 0.8 V
ADN4690E/ADN4692E/ADN4694E/ADN4695E
Parameter
BUS INPUT/OUTPUT
Input Current
A (Receiver or Transceiver with Driver Disabled)
B (Receiver or Transceiver with Driver Disabled)
Differential (Receiver or Transceiver with Driver
Disabled)
Power-Off Input Current
A (Receiver or Transceiver)
B (Receiver or Transceiver)
Differential Input Capacitance (Transceiver with
Driver Disabled)
Input Capacitance Balance (CA/CB) (Transceiver
with Driver Disabled)
POWER SUPPLY
Supply Current
Only Driver Enabled
Both Driver and Receiver Disabled
Both Driver and Receiver Enabled
Only Receiver Enabled
Total Power Dissipation
2
Min
IA
IB
IAB
IA(OFF)
IB(OFF)
Differential (Receiver or Transceiver)
Input Capacitance (Transceiver with Driver Disabled)
1
Symbol
IAB(OFF)
CA or CB
Data Sheet
Typ
Max
Unit
Test Conditions/Comments
0
−20
−32
0
−20
−32
−4
32
+20
0
32
+20
0
+4
µA
µA
µA
µA
µA
µA
µA
VB = 1.2 V, VA = 3.8 V
VB = 1.2 V, VA = 0 V or 2.4 V
VB = 1.2 V, VA = −1.4 V
VA = 1.2 V, VB = 3.8 V
VA = 1.2 V, VB = 0 V or 2.4 V
VA = 1.2 V, VB = −1.4 V
VA = VB, 1.4 ≤ VA ≤ 3.8 V
0
−20
−32
0
−20
−32
−4
32
+20
0
32
+20
0
+4
µA
µA
µA
µA
µA
µA
µA
pF
3
pF
5
CAB
CA/B
0.99
1.01
0 V ≤ VCC ≤ 1.5 V
VB = 1.2 V, VA = 3.8 V
VB = 1.2 V, VA = 0 V or 2.4 V
VB = 1.2 V, VA = −1.4 V
VA = 1.2 V, VB = 3.8 V
VA = 1.2 V, VB = 0 V or 2.4 V
VA = 1.2 V, VB = −1.4 V
VA = VB, 1.4 V ≤ VA ≤ 3.8 V
VI = 0.4 sin(30e6πt) V + 0.5 V,2
other input = 1.2 V, DE = 0 V
VAB = 0.4 sin(30e6πt) V,2 DE = 0 V
DE = 0 V
ICC
13
1
16
4
PD
22
4
24
13
94
mA
mA
mA
mA
mW
DE, RE = VCC, RL = 50 Ω
DE = 0 V, RE = VCC, RL = no load
DE = VCC, RE = 0 V, RL = 50 Ω
DE, RE = 0 V, RL = 50 Ω
RL = 50 Ω, input (DI) = 50 MHz,
50% duty cycle square wave;
DE = VCC; RE = 0 V; TA = 85°C
All typical values are given for VCC = 3.3 V and TA = 25°C.
HP4194A impedance analyzer (or equivalent).
RECEIVER INPUT THRESHOLD TEST VOLTAGES
RE = 0 V, H = high, L = low.
Table 3. Test Voltages for Type 1 Receiver
VA (V)
2.4
0
3.425
3.375
−0.975
−1.025
Applied Voltages
VB (V)
0
2.4
3.375
3.425
−1.025
−0.975
Input Voltage, Differential
VID (V)
2.4
−2.4
0.05
−0.05
0.05
−0.05
Rev. A | Page 4 of 20
Input Voltage, Common Mode
VIC (V)
1.2
1.2
3.4
3.4
−1
−1
Receiver Output
RO
H
L
H
L
H
L
Data Sheet
ADN4690E/ADN4692E/ADN4694E/ADN4695E
Table 4. Test Voltages for Type 2 Receiver
VA (V)
2.4
0
3.475
3.425
−0.925
−0.975
Applied Voltages
VB (V)
0
2.4
3.325
3.375
−1.075
−1.025
Input Voltage, Differential
VID (V)
2.4
−2.4
0.15
0.05
0.15
0.05
Input Voltage, Common Mode
VIC (V)
1.2
1.2
3.4
3.4
−1
−1
Receiver Output
RO
H
L
H
L
H
L
TIMING SPECIFICATIONS
VCC = 3.0 V to 3.6 V; TA = TMIN to TMAX, unless otherwise noted. 1
Table 5.
Parameter
DRIVER
Maximum Data Rate
Propagation Delay
Differential Output Rise/Fall Time
Pulse Skew |tPHL − tPLH|
Part-to-Part Skew
Period Jitter, rms (One Standard Deviation) 2
Peak-to-Peak Jitter2, 4
Disable Time from High Level
Disable Time from Low Level
Enable Time to High Level
Enable Time to Low Level
RECEIVER
Propagation Delay
Rise/Fall Time
Pulse Skew |tRPHL – tRPLH|
Type 1 Receiver (ADN4690E, ADN4692E)
Type 2 Receiver (ADN4694E, ADN4695E)
Part-to-Part Skew 6
Period Jitter, rms (One Standard Deviation)2
Peak-to-Peak Jitter2, 4
Type 1 Receiver (ADN4690E, ADN4692E)
Type 2 Receiver (ADN4694E, ADN4695E)
Disable Time from High Level
Disable Time from Low Level
Enable Time to High Level
Enable Time to Low Level
Symbol
tPLH, tPHL
tR, tF
tSK
tSK(PP)
tJ(PER)
tJ(PP)
Min
100
2
2
Max
Unit
2.5
2.6
30
3.5
3.2
150
0.9
3
150
Mbps
ns
ns
ps
ns
ps
ps
7
7
7
7
ns
ns
ns
ns
6
2.3
ns
ns
ps
ps
ns
ps
ps
ps
ns
ns
ns
ns
2
tPHZ
tPLZ
tPZH
tPZL
tRPLH, tRPHL
tR, tF
Typ
4
4
4
4
2
1
tSK
tSK
tSK(PP)
tJ(PER)
100
300
4
300
500
1
7
tJ(PP)
tJ(PP)
tRPHZ
tRPLZ
tRPZH
tRPZL
200
225
6
6
10
10
700
800
10
10
15
15
All typical values are given for VCC = 3.3 V and TA = 25°C.
Jitter parameters are guaranteed by design and characterization. Values do not include stimulus jitter.
3
tR = tF = 0.5 ns (10% to 90%), measured over 30,000 samples.
4
Peak-to-peak jitter specifications include jitter due to pulse skew (tSK).
5
tR = tF = 0.5 ns (10% to 90%), measured over 100,000 samples.
6
HP4194A impedance analyzer or equivalent.
1
2
Rev. A | Page 5 of 20
Test Conditions/Comments
See Figure 23, Figure 26
See Figure 23, Figure 26
See Figure 23, Figure 26
See Figure 23, Figure 26
50 MHz clock input 3 (see Figure 25)
100 Mbps 215 − 1 PRBS input 5
(see Figure 28)
See Figure 24, Figure 27
See Figure 24, Figure 27
See Figure 24, Figure 27
See Figure 24, Figure 27
CL = 15 pF (see Figure 29, Figure 32)
CL = 15 pF (see Figure 29, Figure 32)
CL = 15 pF (see Figure 29, Figure 32)
CL = 15 pF (see Figure 29, Figure 32)
50 MHz clock input3 (see Figure 31)
100 Mbps 215 − 1 PRBS input5
(see Figure 34)
See Figure 30, Figure 33
See Figure 30, Figure 33
See Figure 30, Figure 33
See Figure 30, Figure 33
ADN4690E/ADN4692E/ADN4694E/ADN4695E
Data Sheet
ABSOLUTE MAXIMUM RATINGS
TA = TMIN to TMAX, unless otherwise noted.
THERMAL RESISTANCE
Table 6.
Parameter
VCC
Digital Input Voltage (DE, , DI)
Receiver Input (A, B) Voltage
Half-Duplex (ADN4690E, ADN4694E)
Full-Duplex (ADN4692E, ADN4695E)
Receiver Output Voltage (RO)
Driver Output (A, B, Y, Z) Voltage
ESD Rating (A, B, Y, Z Pins)
HBM (Human Body Model)
Air Discharge
Contact Discharge
IEC 61000-4-2, Air Discharge
IEC 61000-4-2, Contact Discharge
ESD Rating (Other Pins, HBM)
ESD Rating (All Pins)
FICDM
Machine Model
Operating Temperature Range
Storage Temperature Range
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Rating
–0.5 V to +4 V
–0.5 V to +4 V
Table 7. Thermal Resistance
Package Type
8-Lead SOIC
14-Lead SOIC
–1.8 V to +4 V
–4 V to +6 V
–0.3 V to +4 V
–1.8 V to +4 V
ESD CAUTION
±15 kV
±8 kV
±10 kV
±8 kV
±4 kV
±1.25 kV
±400 V
−40°C to +85°C
−65°C to +150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. A | Page 6 of 20
θJA
121
86
Unit
°C/W
°C/W
Data Sheet
ADN4690E/ADN4692E/ADN4694E/ADN4695E
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
14 VCC
RE 3
DE 4
DI 5
RE 2
DE 3
DI 4
ADN4690E/
ADN4694E
8
VCC
7
B
TOP VIEW
(Not to Scale)
6
A
5
GND
12 A
TOP VIEW
(Not to Scale)
10 Z
11 B
GND 6
9
Y
GND 7
8
NC
NOTES
1. NC = NO CONNECT. DO NOT
CONNECT TO THIS PIN.
10471-002
RO 1
13 VCC
ADN4692E/
ADN4695E
10471-104
NC 1
RO 2
Figure 4. ADN4692E/ADN4695E Pin Configuration
Figure 3. ADN4690E/ADN4694E Pin Configuration
Table 8. Pin Function Descriptions
ADN4690E/
ADN4694E
Pin No.
1
ADN4692E/
ADN4695E
Pin No.
2
Mnemonic
RO
2
3
RE
3
4
DE
4
5
DI
5
N/A
N/A
6
N/A
7
N/A
8
N/A
6, 7
9
10
N/A
12
N/A
11
13, 14
1, 8
GND
Y
Z
A
A
B
B
VCC
NC
Description
Receiver Output. Type 1 receiver (ADN4690E/ADN4692E), when enabled:
If A − B ≥ 50 mV, then RO = logic high. If A − B ≤ −50 mV, then RO = logic low.
Type 2 receiver (ADN4694E/ADN4695E), when enabled:
If A − B ≥ 150 mV, then RO = logic high. If A − B ≤ 50 mV, then RO = logic low.
Receiver output is undefined outside these conditions.
Receiver Output Enable. A logic low on this pin enables the receiver output, RO.
A logic high on this pin places RO in a high impedance state.
Driver Output Enable. A logic high on this pin enables the driver differential outputs.
A logic low on this pin places the driver differential outputs in a high impedance state.
Driver Input. Half-duplex (ADN4690E/ADN4694E), when enabled:
A logic low on DI forces A low and B high, whereas a logic high on DI forces A high and B low.
Full-duplex (ADN4692E/ADN4695E), when enabled:
A logic low on DI forces Y low and Z high, whereas a logic high on DI forces Y high and Z low.
Ground.
Noninverting Driver Output Y.
Inverting Driver Output Z.
Noninverting Receiver Input A and Noninverting Driver Output A.
Noninverting Receiver Input A.
Inverting Receiver Input B and Inverting Driver Output B.
Inverting Receiver Input B.
Power Supply (3.3 V ± 0.3 V).
No Connect. Do not connect to these pins.
Rev. A | Page 7 of 20
ADN4690E/ADN4692E/ADN4694E/ADN4695E
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
16
14
12
10
8
6
4
0
10
15
20
25
30
35
40
45
50
FREQUENCY (MHz)
10471-003
2
–10
–15
–20
–25
–30
–35
–40
–45
–50
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
RECEIVER HIGH LEVEL OUTPUT VOLTAGE, VOH (V)
Figure 8. Receiver Output Current vs. Output Voltage (Output High)
(TA = 25°C)
3.4
30
tPLH
tPHL
25
20
15
10
5
0
20
40
60
80
TEMPERATURE (°C)
3.0
2.8
2.6
2.4
2.2
2.0
–40
6.0
RECEIVER PROPAGATION DELAY (ns)
VCC = 3V
VCC = 3.3V
VCC = 3.6V
30
25
20
15
10
5
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
40
60
80
tRPLH
tRPHL
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
–40
10471-005
0
RECEIVER LOW LEVEL OUTPUT VOLTAGE, VOL (V)
20
Figure 9. Driver Propagation Delay vs. Temperature
(Data Rate = 2 Mbps, VCC = 3.3 V, RL = 50 Ω)
40
0
0
TEMPERATURE (°C)
Figure 6. Power Supply Current vs. Temperature
(Data Rate = 100 Mbps, VCC = 3.3 V)
35
–20
–20
0
20
40
TEMPERATURE (°C)
60
80
10471-008
–20
10471-004
0
–40
3.2
10471-007
DRIVER PROPAGATION DELAY (ns)
DRIVER
RECEIVER (VID = 200mV, VIC = 1V)
RECEIVER LOW LEVEL OUTPUT CURRENT, IOL (mA)
VCC = 3.0V
VCC = 3.3V
VCC = 3.6V
–5
0
Figure 5. Power Supply Current vs. Frequency
(VCC = 3.3 V, TA = 25°C)
SUPPLY CURRENT, ICC (mA)
0
10471-006
DRIVER
RECEIVER (VID = 200mV, VIC = 1V)
18
SUPPLY CURRENT, ICC (mA)
RECEIVER HIGH LEVEL OUTPUT CURRENT (mA)
20
Figure 10. Receiver Propagation Delay vs. Temperature
(Data Rate = 2 Mbps, VCC = 3.3 V, VID = 200 mV, VIC = 1 V, CL = 15 pF)
Figure 7. Receiver Output Current vs. Output Voltage (Output Low)
(TA = 25°C)
Rev. A | Page 8 of 20
Data Sheet
ADN4690E/ADN4692E/ADN4694E/ADN4695E
2.5
2.0
1.5
1.0
0.5
0
20
40
60
80
100
FREQUENCY (MHz)
6
5
4
3
2
1
0
10
40
50
Figure 14. Receiver Jitter (Period) vs. Frequency
(VCC = 3.3 V, TA = 25°C, VIC = 1 V, Clock Input)
20
16
14
12
10
8
6
4
2
0
20
30
40
50
60
70
80
90
100
DATA RATE (Mbps)
80
70
60
50
40
30
20
20
40
60
80
10471-011
10
TEMPERATURE (°C)
300
200
100
–20
0
20
40
60
80
Figure 15. Receiver Jitter (Peak-to-Peak) vs. Temperature
(VCC = 3.3 V, VIC = 1 V, PRBS 215 − 1 NRZ Input)
90
0
400
TEMPERATURE (°C)
100
–20
500
0
–40
Figure 12. Driver Jitter (Peak-to-Peak) vs. Data Rate
(VCC = 3.3 V, TA = 25°C, PRBS 215 − 1 NRZ Input)
0
–40
600
Figure 13. Driver Jitter (Peak-to-Peak) vs. Temperature
(Data Rate = 100 Mbps, VCC = 3.3 V, TA = 25°C, PRBS 215 − 1 NRZ Input)
Rev. A | Page 9 of 20
10471-014
ADDED RECEIVER PEAK-TO-PEAK JITTER (ps)
700
18
10471-010
ADDED DRIVER PEAK-TO-PEAK JITTER (ps)
30
FREQUENCY (MHz)
Figure 11. Driver Jitter (Period) vs. Frequency
(VCC = 3.3 V, TA = 25°C, Clock Input)
ADDED DRIVER PEAK-TO-PEAK JITTER (ps)
20
10471-012
ADDED RECEIVER PERIOD JITTER (ps)
7
10471-009
ADDED DRIVER PERIOD JITTER (ps)
3.0
Data Sheet
2.5ns/DIV
Figure 16. ADN4690E Driver Output Eye Pattern
(Data Rate = 100 Mbps, PRBS 215 − 1 Input, RL = 50 Ω)
Figure 17. ADN4690E Receiver Output Eye Pattern
(Data Rate = 100 Mbps, PRBS 215 − 1, CL = 15 pF)
Rev. A | Page 10 of 20
10471-016
400mV/DIV
2ns/DIV
10471-015
200mV/DIV
ADN4690E/ADN4692E/ADN4694E/ADN4695E
Data Sheet
ADN4690E/ADN4692E/ADN4694E/ADN4695E
TEST CIRCUITS AND SWITCHING CHARACTERISTICS
DRIVER VOLTAGE AND CURRENT MEASUREMENTS
A/Y
3.32kΩ
VOD
DI
VTEST = –1V TO +3.4V
IOS
VCC
49.9Ω
A/Y
+
3.32kΩ
B/Z
VTEST
S1
DI
VTEST = –1V OR +3.4V
S2
–
Figure 18. Driver Voltage Measurement over Common-Mode Range
A/Y
C1
1pF
R1
24.9Ω
10471-020
10471-017
NOTES
1. 1% TOLERANCE FOR ALL RESISTORS.
VTEST
B/Z
Figure 21. Driver Short Circuit
A
≈ 1.3V
B
≈ 0.7V
DI
C3
2.5pF VOC
VOC
NOTES
1. C1, C2, AND C3 ARE 20% AND INCLUDE PROBE/STRAY
CAPACITANCE < 2cm FROM DUT.
2. R1 AND R2 ARE 1%, METAL FILM, SURFACE MOUNT,
<2cm FROM DUT.
10471-018
C2
1pF
Figure 22. Driver Common-Mode Output Voltage (Steady State)
VCC
A/Y
S2
VA(O), VB(O),
VY(O) OR VZ(O)
R1
1.62kΩ
±1%
10471-019
DE B/Z
ΔVOC(SS)
NOTES
1. INPUT PULSE GENERATOR: 1MHz; 50% ± 5% DUTY CYCLE; tR, tF ≤ 1ns.
2. VOC(PP) MEASURED ON TEST EQUIPMENT WITH –3dB BANDWIDTH ≥ 1GHz.
Figure 19. Driver Common-Mode Output Voltage Measurement
S1
VOC(PP)
Figure 20. Maximum Steady-State Output Voltage Measurement
Rev. A | Page 11 of 20
10471-021
R2
24.9Ω
B/Z
ADN4690E/ADN4692E/ADN4694E/ADN4695E
Data Sheet
DRIVER TIMING MEASUREMENTS
VCC
VCC/2
DI
A/Y
C1
1pF
DI
C3
0.5pF OUT
R1
50Ω
tPLH
tPHL
VSS
B/Z
90% VSS
C2
1pF
OUT
90% VSS
0V
0V
10% VSS
VPH
10% VSS
0% VSS
10471-022
NOTES
1. C1, C2, AND C3 ARE 20% AND INCLUDE PROBE/STRAY
CAPACITANCE < 2cm FROM DUT.
2. R1 IS 1%, METAL FILM, SURFACE MOUNT,
<2cm FROM DUT.
VPL
tR
tF
10471-025
NOTES
1. INPUT PULSE GENERATOR: 1MHz; 50% ± 5% DUTY CYCLE; tR, tF ≤ 1ns.
2. MEASURED ON TEST EQUIPMENT WITH –3dB BANDWIDTH ≥ 1GHz.
Figure 23. Driver Timing Measurement
Figure 26. Driver Propagation, Rise/Fall Times and Voltage Overshoot
VCC
A/Y
C1
1pF
DI
DE
C4
0.5pF OUT
R1
24.9Ω
R2
24.9Ω
B/Z
VCC
DE
C3
2.5pF
0.5VCC
0.5VCC
tPZL
tPLZ
0V
C2
1pF
0V
NOTES
1. C1, C2, C3, AND C4 ARE 20% AND INCLUDE PROBE/STRAY
CAPACITANCE < 2cm FROM DUT.
2. R1 AND R2 ARE 1%, METAL FILM, SURFACE MOUNT,
<2cm FROM DUT.
OUT
(DI = 0V)
–0.1V
–0.1V
10471-023
~ –0.6V
tPZH
tPHZ
~ +0.6V
Figure 24. Driver Enable/Disable Time Test Circuit
OUT
(DI = VCC)
0.1V
0.1V
0V
VCC
INPUT
(CLOCK)
VCC/2
NOTES
1. INPUT PULSE GENERATOR: 1MHz; 50% ± 5% DUTY CYCLE; tR, tF ≤ 1ns.
2. MEASURED ON TEST EQUIPMENT WITH –3dB BANDWIDTH ≥ 1GHz.
VCC/2
0V
Figure 27. Driver Enable/Disable Times
1/f0
OUTPUT
VA – VB
OR
VY – VZ
(IDEAL)
10471-026
S1
VCC/2
0V
VCC
0V
INPUT
(PRBS)
0V
VCC/2
VCC/2
0V
0V
0V
1/f0
OUTPUT
VA – VB
OR
VY – VZ
(ACTUAL)
VA – VB
OR
VY – VZ
0V
OUTPUT
0V
VA – VB
OR
VY – VZ
tc(n)
tJ(PP)
NOTES
1. INPUT PULSE GENERATOR: AGILENT 8304A STIMULUS SYSTEM;
100Mbps; 215 – 1PRBS.
2. MEASURED USING TEK TDS6604 WITH TDSJIT3 SOFTWARE.
Figure 28. Driver Peak-to-Peak Jitter Characteristics
Figure 25. Driver Period Jitter Characteristics
Rev. A | Page 12 of 20
10471-027
NOTES
1. INPUT PULSE GENERATOR: AGILENT 8304A STIMULUS SYSTEM;
50MHz; 50% ± 1% DUTY CYCLE.
2. MEASURED USING TEK TDS6604 WITH TDSJIT3 SOFTWARE.
10471-024
tJ(PER) = |tc(n) – 1/f0|
Data Sheet
ADN4690E/ADN4692E/ADN4694E/ADN4695E
RECEIVER TIMING MEASUREMENTS
A
VA
RO
RE
CL
15pF
VB
VOUT
NOTES
1. CL IS 20%, CERAMIC, SURFACE MOUNT, AND
INCLUDES PROBE/STRAY CAPACITANCE
< 2cm FROM DUT.
0V
VID
VOH
1.4V
1.0V
1.2V
A
B
VOUT
90%
VCC/2
10%
VOL
RE
CL
15pF
RE INPUT
90%
VOUT
RL
499Ω
RO
tRPLH
tRPHL
Figure 29. Receiver Timing Measurement
S1
0V
VCC/2
10%
tF
VTEST
tR
NOTES
1. INPUT PULSE GENERATOR: 1MHz; 50% ± 5% DUTY CYCLE; tR, tF ≤ 1ns.
2. MEASURED ON TEST EQUIPMENT WITH –3dB BANDWIDTH ≥ 1GHz.
10471-031
B
10471-028
VID
Figure 32. Receiver Propagation and Rise/Fall Times
10471-029
NOTES
1. CL IS 20% AND INCLUDES PROBE/STRAY
CAPACITANCE < 2cm FROM DUT.
2. RL IS 1% METAL FILM, SURFACE MOUNT, <2cm FROM DUT.
VCC
Figure 30. Receiver Enable/Disable Time
RE INPUT
0.5VCC
0.5VCC
0V
tRPZL
tRPLZ
VCC
VOUT
INPUT
(VA – VB)
(VTEST = VCC)
(A = 1V)
0.5VCC
VOL + 0.5V
1/f0
tRPZH
VOUT
(VTEST = 0V)
(A = 1.4V)
VOH
0.5VCC
VOH
VOH – 0.5V
0.5VCC
0.5VCC
0V
NOTES
1. INPUT PULSE GENERATOR: 1MHz; 50 ± 5% DUTY CYCLE; tR, tF ≤ 1ns.
VOL
1/f0
10471-032
OUTPUT
(IDEAL)
VOL
tRPHZ
Figure 33. Receiver Enable/Disable Times
VOH
OUTPUT
(ACTUAL)
0.5VCC
VA
0.5VCC
INPUT
(PRBS)
VOL
tc(n)
VB
VOH
OUTPUT
Figure 31. Receiver Period Jitter Characteristics
VCC/2
VCC/2
VOL
tJ(PP)
NOTES
1. INPUT PULSE GENERATOR: AGILENT 8304A STIMULUS SYSTEM;
100Mbps; 215 – 1PRBS.
2. MEASURED USING TEK TDS6604 WITH TDSJIT3 SOFTWARE.
Figure 34. Receiver Peak-to-Peak Jitter Characteristics
Rev. A | Page 13 of 20
10471-033
NOTES
1. INPUT PULSE GENERATOR: AGILENT 8304A STIMULUS SYSTEM;
50MHz; 50% ± 1% DUTY CYCLE.
2. MEASURED USING TEK TDS6604 WITH TDSJIT3 SOFTWARE.
10471-030
tJ(PER) = |tc(n) – 1/f0|
ADN4690E/ADN4692E/ADN4694E/ADN4695E
THEORY OF OPERATION
The ADN4690E/ADN4692E/ADN4694E/ADN4695E are
transceivers for transmitting and receiving multipoint, low
voltage differential signaling (M-LVDS) at high speed (data
rates up to 100 Mbps). Each device has a differential line driver
and a differential line receiver, allowing each device to send and
receive data.
Multipoint LVDS expands on the established LVDS low voltage
differential signaling method by allowing bidirectional communication between more than two nodes. Up to 32 nodes can be
connected on an M-LVDS bus.
HALF-DUPLEX/FULL-DUPLEX OPERATION
Half-duplex operation allows a transceiver to transmit or
receive, but not both at the same time. However, with fullduplex operation, a transceiver can transmit and receive
simultaneously. The ADN4690E/ADN4694E are half-duplex
devices in which the driver and the receiver share differential
bus terminals. The ADN4692E/ADN4695E are full-duplex
devices that have dedicated driver output and receiver input
pins. Figure 36 and Figure 37 show typical half- and full-duplex
bus topologies, respectively, for M-LVDS.
THREE-STATE BUS CONNECTION
The outputs of the device can be placed in a high impedance
state by disabling the driver or receiver. This allows several driver
outputs to be connected to a single M-LVDS bus. Note that, on
each bus line, only one driver can be enabled at a time, but
many receivers can be enabled at the same time.
The driver can be enabled or disabled using the driver enable
pin (DE). DE enables the driver outputs when taken high; when
taken low, DE puts the driver outputs into a high impedance state.
Similarly, an active low receiver enable pin (RE) controls the
receiver. Taking this pin low enables the receiver, whereas taking
it high puts the receiver outputs into a high impedance state.
Truth tables for driver and receiver output states under various
conditions are shown in Table 10, Table 11, Table 12, and
Table 13.
TRUTH TABLES
Driver, Half Duplex (ADN4690E/ADN4694E)
Table 10. Transmitting (see Table 9 for Abbreviations)
Power
Yes
Yes
Yes
Yes
Yes
≤1.5 V
DE
H
H
H
L
NC
X
Inputs
DI
H
L
NC
X
X
X
A
H
L
L
Z
Z
Z
Description
High level
Low level
Don’t care
Indeterminate
High impedance (off )
Disconnected
Outputs
B
L
H
H
Z
Z
Z
Driver, Full Duplex (ADN4692E/ADN4695E)
Table 11. Transmitting (see Table 9 for Abbreviations)
Power
Yes
Yes
Yes
Yes
Yes
≤1.5 V
DE
H
H
H
L
NC
X
Inputs
DI
H
L
NC
X
X
X
Y
H
L
L
Z
Z
Z
Outputs
Z
L
H
H
Z
Z
Z
Type 1 Receiver (ADN4690E/ADN4692E)
Table 12. Receiving (see Table 9 for Abbreviations)
Inputs
Power
Yes
Yes
Yes
Yes
Yes
Yes
No
A−B
≥50 mV
≤−50 mV
−50 mV < A − B < 50 mV
NC
X
X
X
Output
RE
L
L
L
L
H
NC
X
RO
H
L
I
I
Z
Z
Z
Type 2 Receiver (ADN4694E/ADN4695E)
Table 13. Receiving (see Table 9 for Abbreviations)
Inputs
Table 9. Truth Table Abbreviations
Abbreviation
H
L
X
I
Z
NC
Data Sheet
Power
Yes
Yes
Yes
Yes
Yes
Yes
No
Rev. A | Page 14 of 20
A−B
RE
Output
RO
≥150 mV
≤50 mV
50 mV < A − B < 150 mV
NC
X
X
X
L
L
L
L
H
NC
X
H
L
I
L
Z
Z
Z
ADN4690E/ADN4692E/ADN4694E/ADN4695E
To minimize disruption to the bus when adding nodes, the
M-LVDS outputs of the device are kept glitch-free when the
device is powering up or down. This feature allows insertion
of devices onto a live M-LVDS bus because the bus outputs are
not switched on before the device is fully powered. In addition,
all outputs are placed in a high impedance state when the device is
powered off.
Type 2 receivers (ADN4694E/ADN4695E) have an open circuit
and bus-idle fail-safe. The input threshold is offset by 100 mV
so that a logic low is present on the receiver output when the
bus is idle or when the receiver inputs are open.
The different receiver thresholds for the two receiver types are
illustrated in Figure 35. See Table 12 and Table 13 for receiver
output states under various conditions.
FAULT CONDITIONS
The ADN4690E/ADN4692E/ADN4694E/ADN4695E contain
short-circuit current protection that protects the part under fault
conditions in the case of short circuits on the bus. This protection
limits the current in a fault condition to 24 mA at the transmitter
outputs for short-circuit faults between −1 V and +3.4 V. Any
network fault must be cleared to avoid data transmission errors
and to ensure reliable operation of the data network and any
devices that are connected to the network.
RECEIVER INPUT THRESHOLDS/FAIL-SAFE
Two receiver types are available, both of which incorporate
protection against short circuits.
The Type 1 receivers of the ADN4690E/ADN4692E incorporate
25 mV of hysteresis. This ensures that slow-changing signals or
a loss of input does not result in oscillation of the receiver output.
Type 1 receiver thresholds are ±50 mV; therefore, the state of the
receiver output is indeterminate if the differential between A and
B is about 0 V. This state occurs if the bus is idle (approximately 0 V
on both A and B), with no drivers enabled on the attached nodes.
Rev. A | Page 15 of 20
0.25
TYPE 1 RECEIVER
OUTPUT
TYPE 2 RECEIVER
OUTPUT
LOGIC 1
LOGIC 1
0.15
UNDEFINED
0.05
0
UNDEFINED
–0.05
–0.15
LOGIC 0
LOGIC 0
10471-034
GLITCH-FREE POWER-UP/POWER-DOWN
DIFFERENTIAL INPUT VOLTAGE (VIA – VIB) [V]
Data Sheet
Figure 35. Input Threshold Voltages
ADN4690E/ADN4692E/ADN4694E/ADN4695E
Data Sheet
APPLICATIONS INFORMATION
M-LVDS extends the low power, high speed, differential signaling of LVDS (low voltage differential signaling) to multipoint
systems where multiple nodes are connected over short distances
in a bus topology network.
With M-LVDS, a transmitting node drives a differential signal
across a transmission medium such as a twisted pair cable. The
transmitted differential signal allows other receiving nodes that
are connected along the bus to detect a differential voltage that
can then be converted back into a single-ended logic signal by
the receiver.
The communication line is typically terminated at both ends
by resistors (RT), the value of which is chosen to match the
characteristic impedance of the medium (typically 100 Ω).
For half-duplex multipoint applications such as the one shown
in Figure 36, only one driver can be enabled at any time. Fullduplex nodes allow a master slave topology, as shown in Figure 37.
In this configuration, a master node can concurrently send and
receive data to/from slave nodes. At any time, only one slave
node can have its driver enabled to concurrently transmit data
back to the master node.
RT
RT
A
A
B
DI
RO RE DE
A
B
RO RE DE
DI
B
ADN4694E
ADN4694E
ADN4694E
ADN4694E
RO RE DE
A
B
DI
RO RE DE
DI
10471-035
NOTES
1. MAXIMUM NUMBER OF NODES: 32.
2. RT IS EQUAL TO THE CHARACTERISTIC IMPEDANCE OF THE CABLE USED.
Figure 36. ADN4694E Typical Half-Duplex M-LVDS Network (Type 2 Receivers with Threshold Offset for Bus-Idle Fail-Safe)
RT
RT
RT
RT
MASTER
A B Z Y
RO RE DE
D
DI
A B Z Y
R
RO RE DE
SLAVE
R
D
RO RE DE
DI
A B Z Y
D
DI
SLAVE
ADN4695E
ADN4695E
ADN4695E
ADN4695E
R
SLAVE
R
RO RE DE
D
DI
NOTES
1. MAXIMUM NUMBER OF NODES: 32.
2. RT IS EQUAL TO THE CHARACTERISTIC IMPEDANCE OF THE CABLE USED.
Figure 37. ADN4695E Typical Full-Duplex M-LVDS Master-Slave Network (Type 2 Receivers with Threshold Offset for Bus-Idle Fail-Safe)
Rev. A | Page 16 of 20
10471-036
A B Z Y
Data Sheet
ADN4690E/ADN4692E/ADN4694E/ADN4695E
OUTLINE DIMENSIONS
5.00 (0.1968)
4.80 (0.1890)
5
1
4
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
6.20 (0.2441)
5.80 (0.2284)
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
0.31 (0.0122)
COPLANARITY
0.10
SEATING
PLANE
0.50 (0.0196)
0.25 (0.0099)
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-012-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
012407-A
8
4.00 (0.1574)
3.80 (0.1497)
Figure 38. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-8)
Dimensions shown in millimeters and (inches)
8.75 (0.3445)
8.55 (0.3366)
8
14
1
7
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0039)
COPLANARITY
0.10
0.51 (0.0201)
0.31 (0.0122)
6.20 (0.2441)
5.80 (0.2283)
0.50 (0.0197)
0.25 (0.0098)
1.75 (0.0689)
1.35 (0.0531)
SEATING
PLANE
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-012-AB
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
060606-A
4.00 (0.1575)
3.80 (0.1496)
Figure 39. 14-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-14)
Dimensions shown in millimeters and (inches)
ORDERING GUIDE
Model 1
ADN4690EBRZ
ADN4690EBRZ-RL7
ADN4692EBRZ
ADN4692EBRZ-RL7
ADN4694EBRZ
ADN4694EBRZ-RL7
ADN4695EBRZ
ADN4695EBRZ-RL7
EVAL-ADN469xEHDEBZ
EVAL-ADN469xEFDEBZ
1
Temperature Range
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Package Description
8-Lead Standard Small Outline Package (SOIC_N)
8-Lead Standard Small Outline Package (SOIC_N)
14-Lead Standard Small Outline Package (SOIC_N)
14-Lead Standard Small Outline Package (SOIC_N)
8-Lead Standard Small Outline Package (SOIC_N)
8-Lead Standard Small Outline Package (SOIC_N)
14-Lead Standard Small Outline Package (SOIC_N)
14-Lead Standard Small Outline Package (SOIC_N)
Evaluation Board for Half-Duplex M-LVDS (ADN4690E, ADN4694E)
Evaluation Board for Full-Duplex M-LVDS (ADN4692E, ADN4695E)
Z = RoHS Compliant Part.
Rev. A | Page 17 of 20
Package Option
R-8
R-8
R-14
R-14
R-8
R-8
R-14
R-14
ADN4690E/ADN4692E/ADN4694E/ADN4695E
NOTES
Rev. A | Page 18 of 20
Data Sheet
Data Sheet
ADN4690E/ADN4692E/ADN4694E/ADN4695E
NOTES
Rev. A | Page 19 of 20
ADN4690E/ADN4692E/ADN4694E/ADN4695E
NOTES
©2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D10471-0-3/12(A)
Rev. A | Page 20 of 20
Data Sheet