PDF Data Sheet Rev. B

FEATURES
FUNCTIONAL BLOCK DIAGRAMS
VCC
Multipoint LVDS transceivers (low voltage differential
signaling driver and receiver pairs)
Switching rate: 200 Mbps (100 MHz)
Supported bus loads: 30 Ω to 55 Ω
Choice of 2 receiver types
Type 1 (ADN4691E/ADN4693E): hysteresis of 25 mV
Type 2 (ADN4696E/ADN4697E): threshold offset of 100 mV
for open-circuit and bus-idle fail-safe
Conforms to TIA/EIA-899 standard for M-LVDS
Glitch free power-up/power-down on M-LVDS bus
Controlled transition times on driver output
Common-mode range: −1 V to +3.4 V, allowing
communication with 2 V of ground noise
Driver outputs high-Z when disabled or powered off
Enhanced ESD protection on bus pins
±15 kV HBM (human body model), air discharge
±8 kV HBM (human body model), contact discharge
±10 kV IEC 61000-4-2, air discharge
±8 kV IEC 61000-4-2, contact discharge
Operating temperature range: −40°C to +85°C
Available in 8-lead (ADN4691E/ADN4696E) and 14-lead
(ADN4693E/ADN4697E) SOIC packages
ADN4691E/
ADN4696E
RO
R
RE
A
B
DE
D
10355-001
DI
GND
Figure 1.
VCC
ADN4693E/
ADN4697E
RO
R
A
B
RE
DE
DI
D
GND
Z
Y
10355-002
Data Sheet
3.3 V, 200 Mbps, Half- and Full-Duplex,
High Speed M-LVDS Transceivers
ADN4691E/ADN4693E/ADN4696E/ADN4697E
Figure 2.
APPLICATIONS
Backplane and cable multipoint data transmission
Multipoint clock distribution
Low power, high speed alternative to shorter RS-485 links
Networking and wireless base station infrastructure
GENERAL DESCRIPTION
The ADN4691E/ADN4693E/ADN4696E/ADN4697E are
multipoint, low voltage differential signaling (M-LVDS)
transceivers (driver and receiver pairs) that can operate at up to
200 Mbps (100 MHz). The receivers detect the bus state with a
differential input of as little as 50 mV over a common-mode
voltage range of −1 V to +3.4 V. ESD protection of up to ±15 kV
is implemented on the bus pins. The devices adhere to the
TIA/EIA-899 standard for M-LVDS and complement TIA/EIA644 LVDS devices with additional multipoint capabilities.
The ADN4691E/ADN4693E are Type 1 receivers with 25 mV of
hysteresis so that slow-changing signals or loss of input does not
lead to output oscillations. The ADN4696E/ADN4697E are
Type 2 receivers exhibiting an offset threshold, guaranteeing the
output state when the bus is idle (bus-idle fail-safe) or the inputs are
open (open-circuit fail-safe).
Rev. B
The devices are available as half-duplex in an 8-lead SOIC package
(the ADN4691E/ADN4696E) or as full-duplex in a 14-lead
SOIC package (the ADN4693E/ADN4697E). A selection table
for the ADN4690E to ADN4697E devices is shown in Table 1.
Table 1. ADN4690E to ADN4697E Selection Table
Part No.
ADN4690E
ADN4691E
ADN4692E
ADN4693E
ADN4694E
ADN4695E
ADN4696E
ADN4697E
Receiver
Type 1
Type 1
Type 1
Type 1
Type 2
Type 2
Type 2
Type 2
Data Rate
100 Mbps
200 Mbps
100 Mbps
200 Mbps
100 Mbps
100 Mbps
200 Mbps
200 Mbps
SOIC
8-lead
8-lead
14-lead
14-lead
8-lead
14-lead
8-lead
14-lead
Duplex
Half
Half
Full
Full
Half
Full
Half
Full
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2011–2016 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADN4691E/ADN4693E/ADN4696E/ADN4697E
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Driver Voltage and Current Measurements............................ 11
Applications ....................................................................................... 1
Driver Timing Measurements .................................................. 12
Functional Block Diagrams ............................................................. 1
Receiver Timing Measurements ............................................... 13
General Description ......................................................................... 1
Theory of Operation ...................................................................... 14
Revision History ........................................................................... 2
Half-Duplex/Full-Duplex Operation ....................................... 14
Specifications..................................................................................... 3
Three-State Bus Connection ..................................................... 14
Receiver Input Threshold Test Voltages .................................... 4
Truth Tables................................................................................. 14
Timing Specifications .................................................................. 5
Glitch-Free Power-Up/Power-Down ....................................... 15
Absolute Maximum Ratings ............................................................ 6
Fault Conditions ......................................................................... 15
Thermal Resistance ...................................................................... 6
Receiver Input Thresholds/Fail-Safe ........................................ 15
ESD Caution .................................................................................. 6
Applications Information .............................................................. 16
Pin Configurations and Function Descriptions ........................... 7
Outline Dimensions ....................................................................... 17
Typical Performance Characteristics ............................................. 8
Ordering Guide .......................................................................... 17
Test Circuits and Switching Characteristics ................................ 11
REVISION HISTORY
1/16—Rev. A to Rev. B
Change to Table 6 ............................................................................. 6
3/12—Rev. 0 to Rev. A
Added ADN4691E and ADN4693E................................. Universal
Changes to Features Section, General Description Section,
and Table 1 ......................................................................................... 1
Added Type 1 Receiver Parameters, Table 2 ................................. 3
Added Table 3, Renumbered Sequentially .................................... 4
Added Type 1 Receiver Parameters, Table 5 ................................. 5
Added Table 7 ....................................................................................6
Changes to Table 8.............................................................................7
Changes to Figure 33...................................................................... 13
Added Table 12 ............................................................................... 14
Changes to Receiver Input Thresholds/Fail-Safe Section
and Figure 36................................................................................... 15
Changes to Ordering Guide .......................................................... 17
12/11—Revision 0: Initial Version
Rev. B | Page 2 of 20
Data Sheet
ADN4691E/ADN4693E/ADN4696E/ADN4697E
SPECIFICATIONS
VCC = 3.0 V to 3.6 V; RL = 50 Ω; TA = TMIN to TMAX, unless otherwise noted. 1
Table 2.
Parameter
DRIVER
Differential Outputs
Differential Output Voltage Magnitude
∆|VOD| for Complementary Output States
Common-Mode Output Voltage (Steady State)
ΔVOC(SS) for Complementary Output States
Peak-to-Peak VOC
Maximum Steady-State Open-Circuit Output
Voltage
Voltage Overshoot
Low to High
High to Low
Output Current
Short Circuit
High Impedance State, Driver Only
Power Off
Output Capacitance
Differential Output Capacitance
Output Capacitance Balance (CY/CZ)
Logic Inputs (DI, DE)
Input High Voltage
Input Low Voltage
Input High Current
Input Low Current
RECEIVER
Differential Inputs
Differential Input Threshold Voltage
Type 1 Receiver (ADN4691E, ADN4693E)
Type 2 Receiver (ADN4696E, ADN4697E)
Input Hysteresis
Type 1 Receiver (ADN4691E, ADN4693E)
Type 2 Receiver (ADN4696E, ADN4697E)
Differential Input Voltage Magnitude
Input Capacitance
Differential Input Capacitance
Input Capacitance Balance (CA/CB)
Logic Output RO
Output High Voltage
Output Low Voltage
High Impedance Output Current
Logic Input RE
Input High Voltage
Input Low Voltage
Input High Current
Input Low Current
Symbol
Min
|VOD|
∆|VOD|
VOC(SS)
ΔVOC(SS)
VOC(PP)
VA(O), VB(O),
VY(O), or VZ(O)
480
−50
0.8
−50
Typ
0
Max
Unit
Test Conditions/Comments
650
+50
1.2
+50
150
2.4
mV
mV
V
mV
mV
V
See Figure 19
See Figure 19
See Figure 20, Figure 23
See Figure 20, Figure 23
See Figure 20, Figure 23
See Figure 21
1.2 VSS
V
V
See Figure 24, Figure 27
See Figure 24, Figure 27
VPH
VPL
−0.2 VSS
|IOS|
IOZ
−15
24
+10
mA
µA
IO(OFF)
−10
+10
µA
CYZ
CY/Z
pF
0.99
2.5
1.01
See Figure 22
–1.4 V ≤ (VY or VZ) ≤ 3.8 V,
other output = 1.2 V
–1.4 V ≤ (VY or VZ) ≤ 3.8 V,
other output = 1.2 V, 0 V ≤ VCC ≤ 1.5 V
VI = 0.4 sin(30e6πt) V + 0.5 V, 2
other output = 1.2 V, DE = 0 V
VAB = 0.4 sin(30e6πt) V,2 DE = 0 V
VIH
VIL
IIH
IIL
2
GND
0
0
VCC
0.8
10
10
V
V
µA
µA
VIH = 2 V
VIL = 0.8 V
VTH
VTH
−50
50
+50
150
mV
mV
See Table 3, Figure 36
See Table 4, Figure 36
CY or CZ
VHYS
VHYS
|VID|
CA or CB
CAB
CA/B
3
pF
25
0
0.05
VCC
3
0.99
2.5
1.01
VOH
VOL
IOZ
2.4
−10
0.4
+15
VIH
VIL
IIH
IIL
2
GND
−10
−10
VCC
0.8
0
0
Rev. B | Page 3 of 20
mV
mV
V
pF
pF
VI = 0.4 sin(30e6πt) V + 0.5 V,2
other input = 1.2 V
VAB = 0.4 sin(30e6πt) V2
V
V
µA
IOH = –8 mA
IOL = 8 mA
VO = 0 V or 3.6 V
V
V
µA
µA
VIH = 2 V
VIL = 0.8 V
ADN4691E/ADN4693E/ADN4696E/ADN4697E
Parameter
BUS INPUT/OUTPUT
Input Current
A (Receiver or Transceiver with Driver Disabled)
Symbol
Min
IA
B (Receiver or Transceiver with Driver Disabled)
IB
Differential (Receiver or Transceiver with Driver
Disabled)
Power-Off Input Current
A (Receiver or Transceiver)
B (Receiver or Transceiver)
Differential Input Capacitance (Transceiver with
Driver Disabled)
Input Capacitance Balance (CA/CB) (Transceiver
with Driver Disabled)
POWER SUPPLY
Supply Current
Only Driver Enabled
Both Driver and Receiver Disabled
Both Driver and Receiver Enabled
Only Receiver Enabled
2
IA(OFF)
IB(OFF)
Differential (Receiver or Transceiver)
Input Capacitance (Transceiver with Driver Disabled)
1
IAB
IAB(OFF)
CA or CB
Data Sheet
Typ
Max
Unit
Test Conditions/Comments
0
−20
−32
0
−20
−32
−4
32
+20
0
32
+20
0
+4
µA
µA
µA
µA
µA
µA
µA
VB = 1.2 V, VA = 3.8 V
VB = 1.2 V, VA = 0 V or 2.4 V
VB = 1.2 V, VA = −1.4 V
VA = 1.2 V, VB = 3.8 V
VA = 1.2 V, VB = 0 V or 2.4 V
VA = 1.2 V, VB = −1.4 V
VA = VB, 1.4 V ≤ VA ≤ 3.8 V
0
−20
−32
0
−20
−32
−4
32
+20
0
32
+20
0
+4
µA
µA
µA
µA
µA
µA
µA
pF
3
pF
5
CAB
CA/B
0.99
1.01
0 V ≤ VCC ≤ 1.5 V
VB = 1.2 V, VA = 3.8 V
VB = 1.2 V, VA = 0 V or 2.4 V
VB = 1.2 V, VA = −1.4 V
VA = 1.2 V, VB = 3.8 V
VA = 1.2 V, VB = 0 V or 2.4 V
VA = 1.2 V, VB = −1.4 V
VA = VB, 1.4 ≤ VA ≤ 3.8 V
VI = 0.4 sin(30e6πt) V + 0.5 V,2
other input = 1.2 V, DE = 0 V
VAB = 0.4 sin(30e6πt) V,2 DE = 0 V
DE = 0 V
ICC
13
1
16
4
22
4
24
13
mA
mA
mA
mA
DE, RE = VCC, RL = 50 Ω
DE = 0 V, RE= VCC, RL = no load
DE = VCC, RE = 0 V, RL = 50 Ω
DE, RE = 0 V, RL = 50 Ω
All typical values are given for VCC = 3.3 V and TA = 25°C.
HP4194A impedance analyzer (or equivalent).
RECEIVER INPUT THRESHOLD TEST VOLTAGES
RE = 0 V, H = high, L = low
Table 3. Test Voltages for Type 1 Receiver
Applied Voltages
VA (V)
VB (V)
2.4
0
0
2.4
3.8
3.75
3.75
3.8
−1.35
−1.4
−1.4
−1.35
Input Voltage, Differential
VID (V)
2.4
−2.4
0.05
−0.05
0.05
−0.05
Input Voltage, Common Mode
VIC (V)
1.2
1.2
3.775
3.775
−1.375
−1.375
Rev. B | Page 4 of 20
Receiver Output
RO (V)
H
L
H
L
H
L
Data Sheet
ADN4691E/ADN4693E/ADN4696E/ADN4697E
Table 4. Test Voltages for Type 2 Receiver
VA (V)
+2.4
0
+3.8
+3.8
−1.25
−1.35
Applied Voltages
VB (V)
0
+2.4
+3.65
+3.75
−1.4
−1.4
Input Voltage, Differential
VID (V)
+2.4
−2.4
+0.15
+0.05
+0.15
+0.05
Input Voltage, Common Mode
VIC (V)
+1.2
+1.2
+3.725
+3.775
−1.325
−1.375
Receiver Output
RO (V)
H
L
H
L
H
L
TIMING SPECIFICATIONS
VCC = 3.0 V to 3.6 V; TA = TMIN to TMAX, unless otherwise noted. 1
Table 5.
Parameter
DRIVER
Maximum Data Rate
Propagation Delay
Differential Output Rise/Fall Time
Pulse Skew |tPHL – tPLH|
Part-to-Part Skew 2
Period Jitter, RMS (1 Standard Deviation) 3
Peak-to-Peak Jitter3, 5
Disable Time from High Level
Disable Time from Low Level
Enable Time to High Level
Enable Time to Low Level
RECEIVER
Propagation Delay
Rise/Fall Time
Pulse Skew |tRPHL – tRPLH|
Type 1 Receiver (ADN4691E, ADN4693E)
Type 2 Receiver (ADN4696E, ADN4697E)
Part-to-Part Skew2
Period Jitter, RMS (1 Standard Deviation)3
Peak-to-Peak Jitter3, 5
Type 1 Receiver (ADN4691E, ADN4693E)
Type 2 Receiver (ADN4696E, ADN4697E)
Disable Time from High Level
Disable Time from Low Level
Enable Time to High Level
Enable Time to Low Level
Symbol
tPLH, tPHL
tR , tF
tSK
tSK(PP)
tJ(PER)
tJ(PP)
tPHZ
tPLZ
tPZH
tPZL
tRPLH, tRPHL
tR , tF
tSK
tSK(PP)
tJ(PER)
tJ(PP)
tJ(PP)
tRPHZ
tRPLZ
tRPZH
tRPZL
Min
Typ
Max
Unit
Test Conditions/Comments
200
1
1
1.5
2.4
1.6
100
1
3
130
7
7
7
7
Mbps
ns
ns
ps
ns
ps
ps
ns
ns
ns
ns
See Figure 24, Figure 27
See Figure 24, Figure 27
See Figure 24, Figure 27
See Figure 24, Figure 27
100 MHz clock input 4 (see Figure 26)
200 Mbps 215 − 1 PRBS input 6 (see Figure 29)
See Figure 25, Figure 28
See Figure 25, Figure 28
See Figure 25, Figure 28
See Figure 25, Figure 28
4
6
2.3
ns
ns
100
300
300
500
1
7
ps
ps
ns
ps
700
800
10
10
15
15
ps
ps
ns
ns
ns
ns
0
2
30
2
1
4
300
450
CL = 15 pF (see Figure 30, Figure 33)
CL = 15 pF (see Figure 30, Figure 33)
CL = 15 pF (see Figure 30, Figure 33)
CL = 15 pF (see Figure 30, Figure 33)
100 MHz clock input 7 (see Figure 32)
200 Mbps 215 − 1 PRBS input 8 (see Figure 35)
See Figure 31, Figure 34
See Figure 31, Figure 34
See Figure 31, Figure 34
See Figure 31, Figure 34
All typical values are given for VCC = 3.3 V and TA = 25°C.
tSK(PP) is defined as the difference between the propagation delays of two devices between any specified terminals. This specification applies to devices at the same VCC
and temperature, and with identical packages and test circuits.
3
Jitter parameters are guaranteed by design and characterization. Values do not include stimulus jitter.
4
tR = tF = 0.5 ns (10% to 90%), measured over 30,000 samples.
5
Peak-to-peak jitter specifications include jitter due to pulse skew (tSK).
6
tR = tF = 0.5 ns (10% to 90%), measured over 100,000 samples.
7
|VID| = 400 mV (ADN4696E, ADN4697E), VIC = 1.1 V, tR = tF = 0.5 ns (10% to 90%), measured over 30,000 samples.
8
|VID| = 400 mV (ADN4696E, ADN4697E), VIC = 1.1 V, tR = tF = 0.5 ns (10% to 90%), measured over 100,000 samples.
1
2
Rev. B | Page 5 of 20
ADN4691E/ADN4693E/ADN4696E/ADN4697E
Data Sheet
ABSOLUTE MAXIMUM RATINGS
TA = TMIN to TMAX, unless otherwise noted.
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Table 6.
Parameter
VCC
Digital Input Voltage (DE, RE, DI)
Receiver Input (A, B) Voltage
Half-Duplex (ADN4691E, ADN4696E)
Full-Duplex (ADN4693E, ADN4697E)
Receiver Output Voltage (RO)
Driver Output (A, B, Y, Z) Voltage
ESD Rating (A, B, Y, Z Pins)
HBM (Human Body Model)
Air Discharge
Contact Discharge
IEC 61000-4-2, Air Discharge
IEC 61000-4-2, Contact Discharge
ESD Rating (Other Pins, HBM)
ESD Rating (All Pins)
FICDM
Operating Temperature Range
Storage Temperature Range
Rating
−0.5 V to +4 V
−0.5 V to +4 V
−1.8 V to +4 V
−4 V to +6 V
−0.3 V to +4 V
−1.8 V to +4 V
THERMAL RESISTANCE
θJA is specified for the worst case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 7. Thermal Resistance
Package Type
8-Lead SOIC
14-Lead SOIC
±15 kV
±8 kV
±10 kV
±8 kV
±4 kV
ESD CAUTION
±1.25 kV
−40°C to +85°C
−65°C to +150°C
Rev. B | Page 6 of 20
θJA
121
86
Unit
°C/W
°C/W
Data Sheet
ADN4691E/ADN4693E/ADN4696E/ADN4697E
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
14
13
VCC
12
A
RE 3
DE 4
RE 2
DE 3
DI 4
ADN4691E/
ADN4696E
8
VCC
7
B
TOP VIEW
(Not to Scale)
6
A
5
GND
TOP VIEW
(Not to Scale)
11
B
10
Z
GND 6
9
Y
GND 7
8
NC
DI 5
10355-003
RO 1
ADN4693E/
ADN4697E
VCC
NC = NO CONNECT
10355-004
NC 1
RO 2
Figure 4. ADN4693E/ADN4697E Pin Configuration
Figure 3. ADN4691E/ADN4696E Pin Configuration
Table 8. Pin Function Descriptions
ADN4691E/
ADN4696E
Pin No.1
1
ADN4693E/
ADN4697E
Pin No.1
2
Mnemonic
RO
2
3
RE
3
4
DE
4
5
DI
5
N/A
N/A
6
N/A
7
N/A
8
N/A
6, 7
9
10
N/A
12
N/A
11
13, 14
1, 8
GND
Y
Z
A
A
B
B
VCC
NC
1
Description
Receiver Output. Type 1 receiver (ADN4691E/ADN4693E), when enabled:
If A − B ≥ 50 mV, then RO = logic high. If A − B ≤ −50 mV, then RO = logic low.
Type 2 receiver (ADN4696E/ADN4697E), when enabled:
If A − B ≥ 150 mV, then RO = logic high. If A − B ≤ 50 mV, then RO = logic low.
Receiver output is undefined outside these conditions.
Receiver Output Enable. A logic low on this pin enables the receiver output, RO. A logic high on this
pin places RO in a high impedance state.
Driver Output Enable. A logic high on this pin enables the driver differential outputs. A logic
low on this pin places the driver differential outputs in a high impedance state.
Driver Input. Half-duplex (ADN4691E/ADN4696E), when enabled:
A logic low on DI forces A low and B high, whereas a logic high on DI forces A high and B low.
Full-duplex (ADN4693E/ADN4697E), when enabled:
A logic low on DI forces Y low and Z high, whereas a logic high on DI forces Y high and Z low.
Ground.
Noninverting Driver Output Y.
Inverting Driver Output Z.
Noninverting Receiver Input A and Noninverting Driver Output A.
Noninverting Receiver Input A.
Inverting Receiver Input B and Inverting Driver Output B.
Inverting Receiver Input B.
Power Supply (3.3 V ± 0.3 V).
No Connect. Do not connect to these pins.
N/A means not applicable.
Rev. B | Page 7 of 20
ADN4691E/ADN4693E/ADN4696E/ADN4697E
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
16
DRIVER
14
12
10
8
6
RECEIVER (VID = 250mV, VIC = 1V)
4
2
0
20
40
80
60
100
10355-005
0
120
FREQUENCY (MHz)
–15
–20
–25
–30
–35
–40
–45
–50
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
RECEIVER HIGH LEVEL OUTPUT VOLTAGE, VOH (V)
Figure 8. Receiver Output Current vs. Output Voltage (Output High)
(TA = 25°C)
20
DIFFERENTIAL OUTPUT VOLTAGE, VOD (V)
2.0
18
DRIVER
16
14
12
10
RECEIVER (VID = 250mV, VIC = 1V)
8
6
4
2
–30
–10
30
10
50
70
90
TEMPERATURE (°C)
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
10355-006
0
–50
1.8
0
2
2.4
DRIVER PROPAGATION DELAY (ns)
VCC = 3V
VCC = 3.3V
VCC = 3.6V
30
25
20
15
10
5
0.5
1.0
1.5
2.0
2.5
3.0
3.5
RECEIVER LOW LEVEL OUTPUT VOLTAGE, VOL (V)
4.0
10
12
14
tPHL
tPLH
2.2
2.0
1.8
1.6
1.4
1.2
1.0
–40
10355-007
0
8
Figure 9. Driver Differential Output Voltage vs. Output Current
(VCC = 3.3 V, TA = 25°C)
40
0
6
OUTPUT CURRENT, IO (mA)
Figure 6. Power Supply Current vs. Temperature (Data Rate = 200 Mbps,
VCC = 3.3 V; Receiver VID = 250 mV, VIC = 1 V)
35
4
10355-009
SUPPLY CURRENT, ICC (mA)
–10
0
Figure 5. Power Supply Current (ICC) vs. Frequency
(VCC = 3.3 V, TA = 25°C; Receiver VID = 250 mV, VIC = 1 V)
RECEIVER LOW LEVEL OUTPUT CURRENT, IOL (mA)
VCC = 3.0V
VCC = 3.3V
VCC = 3.6V
–5
–20
0
20
40
60
TEMPERATURE, TA (°C)
Figure 10. Driver Propagation Delay vs. Temperature
(Data Rate = 2 Mbps, VCC = 3.3 V)
Figure 7. Receiver Output Current vs. Output Voltage (Output Low)
(TA = 25°C)
Rev. B | Page 8 of 20
80
10355-010
SUPPLY CURRENT, ICC (mA)
18
0
10355-008
RECEIVER HIGH LEVEL OUTPUT CURRENT (mA)
20
Data Sheet
ADN4691E/ADN4693E/ADN4696E/ADN4697E
120
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
–50
–30
10
–10
30
50
90
70
TEMPERATURE, TA (°C)
100
80
60
40
20
0
–50
30
50
70
90
Figure 14. Driver Jitter (Peak-to-Peak) vs. Temperature
(Data Rate = 200 Mbps, VCC = 3.3 V, PRBS 215 − 1 Input)
3.0
2.5
2.0
1.5
1.0
0.5
30
50
40
60
80
70
90
100
FREQUENCY (MHz)
5
4
3
2
1
0
0
ADDED RECEIVER PEAK–TO–PEAK JITTER (ps)
100
80
60
40
20
60
80
100
120
140
160
180
DATA RATE (Mbps)
200
100
80
120
800
700
600
500
400
300
200
100
0
–50
10355-013
0
40
60
Figure 15. Receiver Jitter (Period) vs. Frequency
(VCC = 3.3 V, TA = 25°C, VID = 400 mV)
120
20
40
FREQUENCY (MHz)
Figure 12. Driver Jitter (Period) vs. Frequency
(VCC = 3.3 V, TA = 25°C, Clock Input)
0
20
–30
–10
10
30
50
70
90
TEMPERATURE (°C)
Figure 16. Receiver Jitter (Peak-to-Peak) vs. Temperature
(Data Rate = 200 Mbps, VCC = 3.3 V, VID = 400 mV, VIC = 1.1 V,
PRBS 215 − 1 Input)
Figure 13. Driver Jitter (Peak-to-Peak) vs. Data Rate
(VCC = 3.3 V, TA = 25°C, PRBS 215 − 1 Input)
Rev. B | Page 9 of 20
10355-016
0
20
6
10355-015
ADDED RECEIVER PERIOD JITTER (ps)
7
10355-012
ADDED DRIVER PERIOD JITTER (ps)
10
–10
TEMPERATURE, TA (°C)
Figure 11. Receiver Propagation Delay vs. Temperature
(Data Rate = 2 Mbps, VCC = 3.3 V, VID = 400 mV, VIC = 1.1 V)
ADDED DRIVER PEAK-TO-PEAK JITTER (ps)
–30
10355-014
ADDED DRIVER PEAK-TO-PEAK JITTER (ps)
tRPLH
tRPHL
10355-011
RECEIVER PROPAGATION DELAY (ns)
6.0
Data Sheet
10355-017
10355-018
500mV/DIV
200mV/DIV
ADN4691E/ADN4693E/ADN4696E/ADN4697E
1ns/DIV
2.5ns/DIV
Figure 17. ADN4696E Driver Output Eye Pattern
(Data Rate = 200 Mbps, PRBS 215 − 1 Input, RL = 50 Ω)
Figure 18. ADN4696E Receiver Output Eye Pattern
(Data Rate = 200 Mbps, PRBS 215 − 1 Input, CL = 15 pF)
Rev. B | Page 10 of 20
Data Sheet
ADN4691E/ADN4693E/ADN4696E/ADN4697E
TEST CIRCUITS AND SWITCHING CHARACTERISTICS
DRIVER VOLTAGE AND CURRENT MEASUREMENTS
A/Y
3.32kΩ
VOD
DI
IOS
VCC
49.9Ω
A/Y
+
3.32kΩ
B/Z
VTEST –1V TO +3.4V
S1
DI
S2
–1V OR +3.4V
–
10355-022
10355-019
NOTES
1. 1% TOLERANCE FOR ALL RESISTORS
Figure 19. Driver Voltage Measurement over Common-Mode Range
A/Y
C1
1pF
R1
24.9Ω
VTEST
B/Z
Figure 22. Driver Short Circuit
A/Y
≈ 1.3V
B/Z
≈ 0.7V
DI
C3
2.5pF VOC
C2
1pF
NOTES
1. C1, C2, AND C3 ARE 20% AND INCLUDE PROBE/STRAY
CAPACITANCE LESS THAN 2cm FROM DUT.
2. R1 AND R2 ARE 1%, METAL FILM, SURFACE MOUNT,
LESS THAN 2cm FROM DUT.
10355-020
VOC
Figure 23. Driver Common-Mode Output Voltage (Steady State)
VCC
A/Y
S2
VA(O), VB(O),
VY(O) OR VZ(O)
R1
1.62kΩ
±1%
10355-021
DE B/Z
ΔVOC(SS)
NOTES
1. INPUT PULSE GENERATOR: 500kHz; 50% ± 5% DUT Y CYCLE; tR, tF ≤ 1ns.
2. VOC(PP) MEASURED ON TEST EQUIPMENT WITH –3dB BANDWIDTH ≥ 1GHz.
Figure 20. Driver Common-Mode Output Voltage Measurement
S1
VOC(PP)
Figure 21. Maximum Steady-State Output Voltage Measurement
Rev. B | Page 11 of 20
10355-023
R2
24.9Ω
B/Z
ADN4691E/ADN4693E/ADN4696E/ADN4697E
Data Sheet
DRIVER TIMING MEASUREMENTS
VCC
C1
1pF
A/Y
DI
0.5VCC
DI
C3
0.5pF OUT
R1
50Ω
0.5VCC
0V
tPHL
tPLH
B/Z
VSS
C2
1pF
90% VSS
0V
0V
VPH
10% VSS
10% VSS
0% VSS
VPL
tR
Figure 24. Driver Timing Measurement
tF
NOTES
1. INPUT PULSE GENERATOR: 500kHz; 50% ± 5% DUT Y CYCLE; tR, tF ≤ 1ns.
2. MEASURED ON TEST EQUIPMENT WITH –3dB BANDWIDTH ≥ 1GHz.
VCC
Figure 27. Driver Propagation, Rise/Fall Times and Voltage Overshoot
C1
1pF
A/Y
DI
S1
10355-027
OUT
10355-024
NOTES
1. C1, C2, AND C3 ARE 20% AND INCLUDE PROBE/STRAY
CAPACITANCE LESS THAN 2cm FROM DUT.
2. R1 IS 1%, METAL FILM, SURFACE MOUNT,
LESS THAN 2cm FROM DUT.
90% VSS
DE
C4
0.5pF OUT
R1
24.9Ω
R2
24.9Ω
B/Z
VCC
C3
2.5pF
DE
C2
1pF
0.5VCC
0.5VCC
tPZL
tPLZ
0V
0V
OUT
(DI = 0V)
10355-025
NOTES
1. C1, C2, C3, AND C4 ARE 20% AND INCLUDE PROBE/STRAY
CAPACITANCE LESS THAN 2cm FROM DUT.
2. R1 AND R2 ARE 1%, METAL FILM, SURFACE MOUNT,
LESS THAN 2cm FROM DUT.
–0.1V
–0.1V
~ –0.6V
tPZH
Figure 25. Driver Enable/Disable Time
tPHZ
~ 0.6V
OUT
(DI = VCC)
0.1V
0.1V
0V
INPUT
(CLOCK)
VCC/2
NOTES
1. INPUT PULSE GENERATOR: 500kHz; 50% ± 5% DUT Y CYCLE; tR, tF ≤ 1ns.
2. MEASURED ON TEST EQUIPMENT WITH –3dB BANDWIDTH ≥ 1GHz.
VCC/2
0V
Figure 28. Driver Enable/Disable Times
1/f0
OUTPUT
VA – VB
OR
VY – VZ
(IDEAL)
VCC
0V
0V
INPUT
(PRBS)
0.5VCC
0.5VCC
0V
1/f0
OUTPUT
VA – VB
OR
VY – VZ
(ACTUAL )
10355-028
VCC
VA – VB
OR
VY – VZ
0V
0V
OUTPUT
VA – VB
OR
VY – VZ
tc(n)
0V
0V
tJ(PP)
NOTES
1. INPUT PULSE GENERATOR: AGILENT 8304A STIMULUS SYSTEM;
200Mbps; 215 – 1PRBS.
2. MEASURED USING TEK TDS6604 WITH TDSJIT3 SOFTWARE.
Figure 26. Driver Period Jitter Characteristics
Figure 29. Driver Peak-to-Peak Jitter Characteristics
Rev. B | Page 12 of 20
10355-029
NOTES
1. INPUT PULSE GENERATOR: AGILENT 8304A STIMULUS SYSTEM;
100MHz; 50% ± 1% DUTY CYCLE.
2. MEASURED USING TEK TDS6604 WITH TDSJIT3 SOFTWARE.
10355-026
tJ(PER) = |tc(n) – 1/f0|
Data Sheet
ADN4691E/ADN4693E/ADN4696E/ADN4697E
RECEIVER TIMING MEASUREMENTS
A
RO
VID
B
RE
CL
15pF
VA
VOUT
VB
10355-030
NOTES
1. CL IS 20%, CERAMIC, SURFACE MOUNT, AND INCLUDES
PROBE/STRAY CAPACITANCE < 2cm FROM DUT.
Figure 30. Receiver Timing Measurement
0V
0V
VID
1.4V
RL
499Ω
RO
1.0V
1.2V
B
VOH
CL
15pF
RE INPUT
tRPHL
RE
VOUT
tRPLH
90%
VTEST
90%
VOUT
0.5VCC
10%
VOL
0.5VCC
10%
tR
tF
10355-031
NOTES
1. CL IS 20% AND INCLUDES PROBE/STRAY
CAPACITANCE < 2cm FROM DUT.
2. RL IS 1% METAL FILM, SURFACE MOUNT, <2cm FROM DUT.
NOTES
1. INPUT PULSE GENERATOR: 50MHz; 50% ± 5% DUTY CYCLE; tR, tF ≤ 1ns.
2. MEASURED ON TEST EQUIPMENT WITH –3dB BANDWIDTH ≥ 1GHz.
Figure 31. Receiver Enable/Disable Time
Figure 33. Receiver Propagation and Rise/Fall Times
VCC
INPUT
(VA – VB)
RE INPUT
0.5VCC
0.5VCC
0V
0V
1/f0
tRPZL
tRPLZ
VCC
VOUT
(VTEST = VCC)
(A = 1V)
VOH
OUTPUT
(IDEAL)
10355-033
A
0.5VCC
0.5VCC
0.5VCC
VOL + 0.5V
tRPZH
VOL
VOUT
(VTEST = 0V)
(A = 1.4V)
1/f0
VOL
tRPHZ
VOH
VOH – 0.5V
0.5VCC
0.5VCC
NOTES
1. INPUT PULSE GENERATOR: 500kHz; 50% ± 5% DUT Y CYCLE; tR, tF ≤ 1ns.
0.5VCC
Figure 34. Receiver Enable/Disable Times
VOL
tc(n)
VA
tJ(PER) = |tc(n) – 1f0|
Figure 32. Receiver Period Jitter Characteristics
10355-032
NOTES
1. INPUT PULSE GENERATOR: AGILENT 8304A STIMULUS SYSTEM;
100MHz; 50% ± 1% DUTY CYCLE.
2. MEASURED USING TEK TDS6604 WITH TDSJIT3 SOFTWARE.
INPUT
(PRBS)
VB
VOH
OUTPUT
0.5VCC
0.5VCC
VOL
tJ(PP)
NOTES
1. INPUT PULSE GENERATOR: AGILENT 8304A STIMULUS SYSTEM;
200Mbps; 215 – 1PRBS.
2. MEASURED USING TEK TDS6604 WITH TDSJIT3 SOFTWARE.
Figure 35. Receiver Peak-to-Peak Jitter Characteristics
Rev. B | Page 13 of 20
10355-035
OUTPUT
(ACTUAL)
10355-034
0V
VOH
ADN4691E/ADN4693E/ADN4696E/ADN4697E
Data Sheet
THEORY OF OPERATION
The ADN4691E/ADN4693E/ADN4696E/ADN4697E are transceivers for transmitting and receiving multipoint, low voltage
differential signaling (M-LVDS) at high speed (data rates up
to 200 Mbps). Each device has a differential line driver and a
differential line receiver, allowing each device to send and
receive data.
Multipoint LVDS expands on the established LVDS low voltage
differential signaling method by allowing bidirectional communication between more than two nodes. Up to 32 nodes can
connect on an M-LVDS bus.
HALF-DUPLEX/FULL-DUPLEX OPERATION
Half-duplex operation allows a transceiver to transmit or
receive, but not both at the same time. However, with fullduplex operation, a transceiver can transmit and receive
simultaneously. The ADN4691E/ADN4696E are half-duplex
devices in which the driver and the receiver share differential
bus terminals. The ADN4693E/ADN4697E are full-duplex
devices that have dedicated driver output and receiver input
pins. Figure 37 and Figure 38 show typical half- and full-duplex
bus topologies, respectively, for M-LVDS.
THREE-STATE BUS CONNECTION
The outputs of the device can be placed in a high impedance
state by disabling the driver or receiver. This allows several
driver outputs to connect to a single M-LVDS bus. Note that, on
each bus line, only one driver can be enabled at a time, but
many receivers can be enabled at the same time.
The driver can be enabled or disabled using the driver enable
pin (DE). DE enables the driver outputs when taken high; when
taken low, DE puts the driver outputs into a high impedance state.
Similarly, an active low receiver enable pin (RE) controls the
receiver. Taking RE low enables the receiver, whereas taking it
high puts the receiver outputs into a high impedance state.
Truth tables for driver and receiver output states under various
conditions are shown in Table 10, Table 11, Table 12, and Table 13.
TRUTH TABLES
Table 9. Truth Table Abbreviations
Abbreviation
H
L
X
I
Z
NC
Description
High level
Low level
Don’t care
Indeterminate
High impedance (off )
Disconnected
Driver, Half-Duplex (ADN4691E/ADN4696E)
Table 10. Transmitting (See Table 9 for Abbreviations)
Power
Yes
Yes
Yes
Yes
Yes
≤1.5 V
DE
H
H
H
L
NC
X
Inputs
DI
H
L
NC
X
X
X
A
H
L
L
Z
Z
Z
Outputs
B
L
H
H
Z
Z
Z
Driver, Full-Duplex (ADN4693E/ADN4697E)
Table 11. Transmitting (See Table 9 for Abbreviations)
Power
Yes
Yes
Yes
Yes
Yes
≤1.5 V
DE
H
H
H
L
NC
X
Inputs
DI
H
L
NC
X
X
X
Y
H
L
L
Z
Z
Z
Outputs
Z
L
H
H
Z
Z
Z
Type 1 Receiver (ADN4691E/ADN4693E)
Table 12. Receiving (see Table 9 for Abbreviations)
Inputs
Power
Yes
Yes
Yes
Yes
Yes
Yes
No
A−B
RE
Output
RO
≥50 mV
≤−50 mV
−50 mV < A − B < 50 mV
NC
X
X
X
L
L
L
L
H
NC
X
H
L
I
I
Z
Z
Z
Type 2 Receiver (ADN4696E/ADN4697E)
Table 13. Receiving (See Table 9 for Abbreviations)
Inputs
Power
Yes
Yes
Yes
Yes
Yes
Yes
No
Rev. B | Page 14 of 20
A−B
≥150 mV
≤50 mV
50 mV < A − B < 150 mV
NC
X
X
X
Output
RE
L
L
L
L
H
NC
X
RO
H
L
I
L
Z
Z
Z
ADN4691E/ADN4693E/ADN4696E/ADN4697E
To minimize disruption to the bus when adding nodes, the
M-LVDS outputs of the device are kept glitch-free when the
device is powering up or down. This feature allows insertion of
devices onto a live M-LVDS bus because the bus outputs are not
switched on before the device is fully powered. In addition, all
outputs are placed in a high impedance state when the device is
powered off.
Type 2 receivers (ADN4696E/ADN4697E) have an open circuit
and bus-idle fail-safe. The input threshold is offset by 100 mV so
a logic low is present on the receiver output when the bus is idle
or when the receiver inputs are open.
The different receiver thresholds for the two receiver types are
illustrated in Figure 36. See Table 12 and Table 13 for receiver
output states under various conditions.
FAULT CONDITIONS
The ADN4691E/ADN4693E/ADN4696E/ADN4697E contain
short-circuit current protection that protects the device under
fault conditions in the case of short circuits on the bus. This
protection limits the current in a fault condition to 24 mA at
the transmitter outputs for short-circuit faults between −1 V
and 3.4 V. Any network fault must clear to avoid data
transmission errors and to ensure reliable operation of the data
network and any devices that are connected to the network.
RECEIVER INPUT THRESHOLDS/FAIL-SAFE
Two receiver types are available, both of which incorporate
protection against short circuits.
The Type 1 receivers of the ADN4691E/ADN4693E incorporate
25 mV of hysteresis. This ensures that slow changing signals or
a loss of input does not result in oscillation of the receiver output.
Type 1 receiver thresholds are ±50 mV; therefore, the state of the
receiver output is indeterminate if the differential between A and
B is about 0 V. This state occurs if the bus is idle (approximately 0 V
on both A and B), with no drivers enabled on the attached nodes.
Rev. B | Page 15 of 20
0.25
TYPE 1 RECEIVER
OUTPUT
TYPE 2 RECEIVER
OUTPUT
LOGIC 1
LOGIC 1
0.15
UNDEFINED
0.05
0
UNDEFINED
–0.05
–0.15
LOGIC 0
LOGIC 0
10355-036
GLITCH-FREE POWER-UP/POWER-DOWN
DIFFERENTIAL INPUT VOLTAGE (VIA – VIB) [V]
Data Sheet
Figure 36. Input Threshold Voltages
ADN4691E/ADN4693E/ADN4696E/ADN4697E
Data Sheet
APPLICATIONS INFORMATION
M-LVDS extends the low power, high speed, differential signaling
of low voltage differential signaling (LVDS) to multipoint systems
where multiple nodes are connected over short distances in a
bus topology network.
With M-LVDS, a transmitting node drives a differential signal
across a transmission medium such as a twisted pair cable. The
transmitted differential signal allows other receiving nodes that
are connected along the bus to detect a differential voltage that
can then be converted back into a single-ended logic signal by
the receiver.
The communication line is typically terminated at both ends
by resistors (RT), the value of which is chosen to match the
characteristic impedance of the medium (typically 100 Ω).
For half-duplex multipoint applications such as the one shown
in Figure 37, only one driver can be enabled at any time. Fullduplex nodes allow a master-slave topology as shown in Figure 38.
In this configuration, a master node can concurrently send and
receive data to/from slave nodes. At any time, only one slave
node can have a driver enabled to concurrently transmit data
back to the master node.
RT
RT
A
B
A
B
ADN4696E
R
D
RO RE DE
DI
A
B
ADN4696E
R
DI
B
ADN4696E
R
D
RO RE DE
A
D
RO RE DE
DI
ADN4696E
R
D
RO RE DE
DI
10355-037
NOTES
1. MAXIMUM NUMBER OF NODES: 32.
2. RT IS EQUAL TO THE CHARACTERISTIC IMPEDANCE OF THE CABLE USED.
Figure 37. ADN4696E Typical Half-Duplex M-LVDS Network (Type 2 Receivers with Threshold Offset for Bus-Idle Fail-Safe)
RT
RT
RT
RT
MASTER
A B Z Y
RO RE DE
D
DI
A B Z Y
R
RO RE DE
SLAVE
R
D
DI
A B Z Y
ADN4697E
ADN4697E
ADN4697E
R
SLAVE
RO RE DE
D
DI
SLAVE
ADN4697E
R
RO RE DE
D
DI
NOTES
1. MAXIMUM NUMBER OF NODES: 32.
2. RT IS EQUAL TO THE CHARACTERISTIC IMPEDANCE OF THE CABLE USED.
Figure 38. ADN4697E Typical Full-Duplex M-LVDS Master-Slave Network (Type 2 Receivers with Threshold Offset for Bus-Idle Fail-Safe)
Rev. B | Page 16 of 20
10355-038
A B Z Y
Data Sheet
ADN4691E/ADN4693E/ADN4696E/ADN4697E
OUTLINE DIMENSIONS
5.00 (0.1968)
4.80 (0.1890)
5
1
6.20 (0.2441)
5.80 (0.2284)
4
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
0.31 (0.0122)
COPLANARITY
0.10
SEATING
PLANE
0.50 (0.0196)
0.25 (0.0099)
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-012-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
012407-A
8
4.00 (0.1574)
3.80 (0.1497)
Figure 39. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-8)
Dimensions shown in millimeters and (inches)
8.75 (0.3445)
8.55 (0.3366)
8
14
1
7
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0039)
COPLANARITY
0.10
0.51 (0.0201)
0.31 (0.0122)
6.20 (0.2441)
5.80 (0.2283)
0.50 (0.0197)
0.25 (0.0098)
1.75 (0.0689)
1.35 (0.0531)
SEATING
PLANE
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-012-AB
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
060606-A
4.00 (0.1575)
3.80 (0.1496)
Figure 40. 14-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-14)
Dimensions shown in millimeters and (inches)
ORDERING GUIDE
Model 1
ADN4691EBRZ
ADN4691EBRZ-RL7
ADN4693EBRZ
ADN4693EBRZ-RL7
ADN4696EBRZ
ADN4696EBRZ-RL7
ADN4697EBRZ
ADN4697EBRZ-RL7
EVAL-ADN469xEHDEBZ
EVAL-ADN469xEFDEBZ
1
Temperature Range
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Package Description
8-Lead Standard Small Outline Package (SOIC_N)
8-Lead Standard Small Outline Package (SOIC_N)
14-Lead Standard Small Outline Package (SOIC_N)
14-Lead Standard Small Outline Package (SOIC_N)
8-Lead Standard Small Outline Package (SOIC_N)
8-Lead Standard Small Outline Package (SOIC_N)
14-Lead Standard Small Outline Package (SOIC_N)
14-Lead Standard Small Outline Package (SOIC_N)
Evaluation Board for Half-Duplex (ADN4691E/ADN4696E)
Evaluation Board for Full-Duplex (ADN4693E/ADN4697E)
Z = RoHS Compliant Part.
Rev. B | Page 17 of 20
Package Option
R-8
R-8
R-14
R-14
R-8
R-8
R-14
R-14
ADN4691E/ADN4693E/ADN4696E/ADN4697E
NOTES
Rev. B | Page 18 of 20
Data Sheet
Data Sheet
ADN4691E/ADN4693E/ADN4696E/ADN4697E
NOTES
Rev. B | Page 19 of 20
ADN4691E/ADN4693E/ADN4696E/ADN4697E
NOTES
©2011–2016 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D10355-0-1/16(B)
Rev. B | Page 20 of 20
Data Sheet