MAXIM MAX395EWG

19-0448; Rev 0; 11/95
Serially Controlled, Low-Voltage,
8-Channel SPST Switch
________________________Applications
Serial Data-Acquisition
Systems
Avionics
Audio Signal Routing
Industrial and ProcessControl Systems
ATE Equipment
Networking
__________________Pin Configuration
____________________________Features
♦ SPI™/QSPI™, Microwire™-Compatible Serial
Interface
♦ 8 Separately Controlled SPST Switches
♦ 100Ω Signal Paths with ±5V Supplies
♦ Rail-to-Rail Signal Handling
♦ Asynchronous RESET Input
♦ Pin Compatible with Industry-Standard MAX335
♦ ±2.7V to ±8V Dual Supplies
+2.7V to +16V Single Supply
♦ >2kV ESD Protection per Method 3015.7
♦ TTL/CMOS-Compatible Inputs (with +5V or
±5V Supplies)
______________Ordering Information
PART
TEMP. RANGE
PIN-PACKAGE
MAX395CNG
0°C to +70°C
24 Narrow Plastic DIP
MAX395CWG
MAX395C/D
MAX395ENG
0°C to +70°C
0°C to +70°C
-40°C to +85°C
24 Wide SO
Dice*
24 Narrow Plastic DIP
MAX395EWG
-40°C to +85°C
24 Wide SO
MAX395MRG
-55°C to +125°C
24 Narrow CERDIP**
* Contact factory for dice specifications.
** Contact factory for availability.
________________Functional Diagram
NO0
NO7
TOP VIEW
SCLK
1
V+
2
DIN
3
GND
4
21 V-
NO0
5
20 NO7
COM0
6
19 COM7
NO1
7
18 NO6
COM1
8
17 COM6
NO2
9
16 NO5
MAX395
24 CS
23 RESET
LOGIC
COM2 10
15 COM5
NO3 11
COM0
COM7
22 DOUT
PARALLEL REGISTER AND TRANSLATOR
DIN
RESET
MAX395
SCLK
CLOCK TRANSLATOR
14 NO4
COM3 12
DOUT
8-BIT SHIFT REGISTER
LATCH
13 COM4
DIP/SO
CS
CS TRANSLATOR
SPI and QSPI are trademarks of Motorola, Inc. Microwire is a trademark of National Semiconductor Corp.
________________________________________________________________ Maxim Integrated Products
Call toll free 1-800-998-8800 for free samples or literature.
1
MAX395
_______________General Description
The MAX395 8-channel, serially controlled, single-pole/single-throw (SPST) analog switch offers eight separately
controlled switches. The switches conduct equally well in
either direction. On-resistance (100Ω max) is matched
between switches to 5Ω max and is flat (10Ω max) over
the specified signal range.
These CMOS devices can operate continuously with
dual power supplies ranging from ±2.7V to ±8V or a
single supply between +2.7V and +16V. Each switch
can handle rail-to-rail analog signals. The off leakage
current is only 0.1nA at +25°C or 5nA at +85°C.
Upon power-up, all switches are off, and the internal shift
registers are reset to zero. The MAX395 is electrically
equivalent to two MAX391 quad switches controlled by a
serial interface, and is pin compatible with the MAX335.
The serial interface is compatible with SPI™/QSPI™ and
Microwire™. Functioning as a shift register, it allows data
(at DIN) to be clocked in synchronously with the rising
edge of clock (SCLK). The shift register’s output (DOUT)
enables several MAX395s to be daisy chained.
All digital inputs have 0.8V to 2.4V logic thresholds, ensuring both TTL- and CMOS-logic compatibility when using
±5V supplies or a single +5V supply.
MAX395
Serially Controlled, Low-Voltage,
8-Channel SPST Switch
ABSOLUTE MAXIMUM RATINGS
Voltages Referenced to GND
V+ ...........................................................................-0.3V, +17V
V- ............................................................................-17V, +0.3V
V+ to V-...................................................................-0.3V, +17V
SCLK, CS, DIN, DOUT, RESET .................-0.3V to (V+ + 0.3V)
NO, COM .................................................(V- - 2V) to (V+ + 2V)
Continuous Current into Any Terminal..............................±30mA
Peak Current, NO_ or COM_
(pulsed at 1ms,10% duty cycle)..................................±100mA
Continuous Power Dissipation (TA = +70°C)
Narrow Plastic DIP (derate 13.33mW/°C above +70°C)...1067mW
Wide SO (derate 11.76mW/°C above +70°C)...............941mW
Narrow CERDIP (derate 12.50mW/°C above +70°C)....1000mW
Operating Temperature Ranges
MAX395C_ G .......................................................0°C to +70°C
MAX395E_ G ....................................................-40°C to +85°C
MAX395MRG ..................................................-55°C to +125°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—Dual Supplies
(V+ = +4.5V to +5.5V, V- = -4.5V to -5.5V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
MIN
CONDITIONS
TYP
(Note 1)
MAX
V+
V
60
100
Ω
UNITS
ANALOG SWITCH
Analog Signal Range
COM, NO On-Resistance
COM, NO On-Resistance Match
Between Channels (Note 2)
COM, NO On-Resistance
Flatness (Note 2)
NO Off Leakage Current
(Note 3)
COM Off Leakage Current
(Note 3)
COM On Leakage Current
(Note 3)
VCOM, VNO
C, E, M
V-
RON
V+ = 5V, V- = -5V,
VCOM = ±3V, INO = 1mA
TA = +25°C
∆RON
V+ = 5V, V- = -5V,
VCOM = ±3V, INO = 1mA
TA = +25°C
5
C, E, M
10
V+ = 5V, V- = -5V, INO = 1mA,
VCOM = -3V, 0V, 3V
TA = +25°C
10
C, E, M
15
V+ = 5.5V, V- = -5.5V,
VCOM = -4.5V, VNO = 4.5V
TA = +25°C
-0.1
C, E, M
-10
V+ = 5.5V, V- = -5.5V,
VCOM = 4.5V, VNO = -4.5V
TA = +25°C
-0.1
C, E, M
-10
V+ = 5.5V, V- = -5.5V,
VCOM = -4.5V, VNO = 4.5V
TA = +25°C
-0.1
C, E, M
-10
V+ = 5.5V, V- = -5.5V,
VCOM = 4.5V, VNO = -4.5V
TA = +25°C
0.1
C, E, M
-10
V+ = 5.5V, V- = -5.5V,
VCOM = VNO = ±4.5V
TA = +25°C
-0.2
C, E, M
-20
2.4
RFLAT(ON)
INO(OFF)
ICOM(OFF)
ICOM(ON)
C, E, M
125
0.002
0.1
0.002
0.1
0.002
0.1
0.002
0.1
0.01
0.2
10
Ω
Ω
nA
10
10
nA
10
20
nA
DIGITAL I/O
DIN, SCLK, CS, RESET Input
Voltage Logic Threshold High
VIH
C, E, M
DIN, SCLK, CS, RESET Input
Voltage Logic Threshold Low
VIL
C, E, M
DIN, SCLK, CS, RESET Input
Current Logic High or Low
IIH, IIL
VDIN, VSCLK,
V CS = 0.8V or 2.4V
C, E, M
-1
DOUT Output Voltage Logic High
VDOUT
IDOUT = 0.8mA
C, E, M
DOUT Output Voltage Logic Low
VDOUT
IDOUT = -1.6mA
C, E, M
SCLK Input Hysteresis
2
SCLKHYST
C, E, M
V
0.8
V
1
µA
2.8
V+
V
0
0.4
0.03
100
_______________________________________________________________________________________
V
mV
Serially Controlled, Low-Voltage,
8-Channel SPST Switch
(V+ = +4.5V to +5.5V, V- = -4.5V to -5.5V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
MIN
CONDITIONS
TYP
(Note 1)
MAX
200
400
500
400
500
UNITS
SWITCH DYNAMIC CHARACTERISTICS
Turn-On Time
tON
From rising edge of CS
Turn-Off Time
tOFF
From rising edge of CS
Break-Before-Make Delay
Charge Injection (Note 4)
NO Off Capacitance
COM Off Capacitance
tBBM
VCTE
From rising edge of CS
CL = 1nF, VNO = 0V, RS = 0Ω
VNO = GND, f = 1MHz
VCOM = GND, f = 1MHz
VCOM = VNO = GND,
f = 1MHz
RL = 50Ω, CL = 15pF,
VNO = 1VRMS, f = 100kHz
RL = 50Ω, CL = 15pF,
VNO = 1VRMS, f = 100kHz
CNO(OFF)
CCOM(OFF)
Switch On Capacitance
C(ON)
Off Isolation
VISO
Channel-to-Channel Crosstalk
VCT
POWER SUPPLY
Power-Supply Range
V+, V-
V+ Supply Current
I+
DIN = CS = SCLK = 0V or V+,
RESET = 0V or V+
V- Supply Current
I-
DIN = CS = SCLK = 0V or V+,
RESET = 0V or V+
TA = +25°C
C, E, M
TA = +25°C
C, E, M
TA = +25°C
TA = +25°C
TA = +25°C
TA = +25°C
90
5
15
2
2
2
10
ns
ns
ns
pC
pF
pF
TA = +25°C
8
pF
TA = +25°C
-90
dB
TA = +25°C
<-90
dB
C, E, M
TA = +25°C
C, E, M
TA = +25°C
C, E, M
±3
7
-1
-2
0.1
±8
20
30
1
2
V
µA
µA
_______________________________________________________________________________________
3
MAX395
ELECTRICAL CHARACTERISTICS—Dual Supplies (continued)
MAX395
Serially Controlled, Low-Voltage,
8-Channel SPST Switch
TIMING CHARACTERISTICS—Dual Supplies (Figure 1)
(V+ = +4.5V to +5.5V, V- = -4.5V to -5.5V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SERIAL DIGITAL INTERFACE
SCLK Frequency
Cycle Time
SYMBOL
MIN
CONDITIONS
TYP
MAX
(Note 1)
fSCLK
tCH + tCL
C, E, M
C, E, M
0
480
CS Lead Time
tCSS
C, E, M
240
ns
CS Lag Time
tCSH2
C, E, M
240
ns
C, E, M
C, E, M
C, E, M
C, E, M
TA = +25°C
C, E, M
190
190
200
0
ns
ns
ns
ns
SCLK High Time
SCLK Low Time
Data Setup Time
Data Hold Time
DIN Data Valid after Falling SCLK
(Note 4)
tCH
tCL
tDS
tDH
tDO
Rise Time of DOUT (Note 4)
tDR
Allowable Rise Time at DIN, SCLK
(Note 4)
tSCR
Fall Time of DOUT (Note 4)
Allowable Fall Time at DIN, SCLK
(Note 4)
RESET Minimum Pulse Width
tDF
tSCF
tRW
50% of SCLK to 10% of DOUT,
CL = 10pF
20% of V+ to 70% of V+,
CL = 10pF
20% of V+ to 70% of V+,
CL = 10pF
20% of V+ to 70% of V+,
CL = 10pF
20% of V+ to 70% of V+,
CL = 10pF
2.1
UNITS
17
-17
85
400
MHz
ns
ns
C, E, M
100
ns
C, E, M
2
µs
C, E, M
100
ns
2
µs
C, E, M
TA = +25°C
70
ns
Note 1: The algebraic convention is used in this data sheet; the most negative value is shown in the minimum column.
Note 2: ∆RON = RON(max) - RON(min). On-resistance match between channels and on-resistance flatness are guaranteed only with
specified voltages. Flatness is defined as the difference between the maximum and minimum value of on-resistance as
measured over the specified analog signal range.
Note 3: Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at room temp.
Note 4: Guaranteed by design.
Note 5: Leakage testing at single supply is guaranteed by testing with dual supplies.
Note 6: See Figure 6. Off isolation = 20log10 VCOM/VNO, VCOM = output. NO = input to off switch.
Note 7: Between any two switches. See Figure 3.
4
_______________________________________________________________________________________
Serially Controlled, Low-Voltage,
8-Channel SPST Switch
(V+ = +4.5V to +5.5V, V- = 0V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
MIN
CONDITIONS
TYP
(Note 2)
MAX
V+
V
125
175
Ω
UNITS
ANALOG SWITCH
Analog Signal Range
COM, NO On-Resistance
NO Off Leakage Current
(Notes 4, 5)
COM Off Leakage Current
(Notes 4, 5)
COM On Leakage Current
(Notes 4, 5)
VCOM, VNO
RON
INO(OFF)
ICOM(OFF)
ICOM(ON)
C, E, M
V-
TA = +25°C
V+ = 5V, VCOM = 3.5V,
INO = 1mA
C, E, M
V+ = 5.5V, VCOM = 4.5V,
VNO = 0V
TA = +25°C
-0.1
C, E, M
-10
TA = +25°C
-0.1
V+ = 5.5V, VCOM = 0V,
VNO = 4.5V
V+ = 5.5V, VCOM = 4.5V,
VNO = 0V
V+ = 5.5V, VCOM = 0V,
VNO = 4.5V
V+ = 5.5V,
VCOM = VNO = 4.5V
225
C, E, M
-10
TA = +25°C
-0.1
C, E, M
-10
TA = +25°C
-0.1
C, E, M
-10
TA = +25°C
-0.2
C, E, M
-20
2.4
0.002
0.1
0.002
0.1
0.002
0.1
0.002
0.1
0.002
0.2
10
nA
10
10
nA
10
20
nA
DIGITAL I/O
DIN, SCLK, CS, RESET Input
Voltage Logic Threshold High
VIH
C, E, M
DIN, SCLK, CS, RESET Input
Voltage Logic Threshold Low
VIL
C, E, M
DIN, SCLK, CS, RESET Input
Current Logic High or Low
IIH, IIL
VDIN, VSCLK,
V CS = 0.8V or 2.4V
C, E, M
-1
DOUT Output Voltage Logic High
VDOUT
IDOUT = -0.8mA
C, E, M
DOUT Output Voltage Logic Low
VDOUT
IDOUT = 1.6mA
C, E, M
SCLK Input Hysteresis
SCLKHYST
V
0.8
V
1
µA
2.8
V+
V
0
0.4
0.03
C, E, M
100
TA = +25°C
200
V
mV
SWITCH DYNAMIC CHARACTERISTICS
400
Turn-On Time
tON
From rising edge of CS
Turn-Off Time
tOFF
From rising edge of CS
Break-Before-Make Delay
tBBM
From rising edge of CS
TA = +25°C
15
Charge Injection (Note 4)
VCTE
CL = 1nF, VNO = 0V, RS = 0Ω
TA = +25°C
2
Off Isolation (Note 6)
VISO
RL = 50Ω, CL = 15pF,
VNO = 1VRMS, f = 100kHz
TA = +25°C
-90
dB
Channel-to-Channel Crosstalk
(Note 7)
VCT
RL = 50Ω, CL = 15pF,
VNO = 1VRMS, f = 100kHz
TA = +25°C
<-90
dB
I+
DIN = CS = SCLK = 0V or
V+, RESET = 0V or V+
TA = +25°C
7
C, E, M
TA = +25°C
500
90
C, E, M
400
500
ns
ns
ns
10
pC
POWER SUPPLY
V+, V- Supply Current
C, E, M
20
30
µA
_______________________________________________________________________________________
5
MAX395
ELECTRICAL CHARACTERISTICS—Single +5V Supply
MAX395
Serially Controlled, Low-Voltage,
8-Channel SPST Switch
TIMING CHARACTERISTICS—Single +5V Supply (Figure 1)
(V+ = +4.5V to +5.5V, V- = 0V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SERIAL DIGITAL INTERFACE
SCLK Frequency
SYMBOL
MIN
CONDITIONS
TYP
(Note 2)
MAX
fSCLK
C, E, M
0
tCH + tCL
C, E, M
480
ns
CS Lead Time (Note 4)
tCSS
C, E, M
240
ns
CS Lag Time (Note 4)
tCSH2
C, E, M
240
ns
C, E, M
C, E, M
C, E, M
C, E, M
TA = +25°C
C, E, M
190
190
200
0
ns
ns
ns
ns
Cycle Time (Note 4)
2.1
UNITS
MHz
SCLK High Time (Note 4)
SCLK Low Time (Note 4)
Data Setup Time (Note 4)
Data Hold Time (Note 4)
tCH
tCL
tDS
tDH
DIN Data Valid after Falling SCLK
(Note 4)
tDO
50% of SCLK to 10% of
DOUT, CL = 10pF
Rise Time of DOUT (Note 4)
tDR
20% of V+ to 70% of V+,
CL = 10pF
C, E, M
100
ns
Allowable Rise Time at DIN,
SCLK (Note 4)
tSCR
20% of V+ to 70% of V+,
CL = 10pF
C, E, M
2
µs
Fall Time of DOUT (Note 4)
tDF
20% of V+ to 70% of V+,
CL = 10pF
C, E, M
100
ns
Allowable Fall Time at DIN,
SCLK (Note 4)
tSCF
20% of V+ to 70% of V+,
CL = 10pF
C, E, M
2
µs
RESET Minimum Pulse Width
tRW
TA = +25°C
17
-17
85
400
70
ns
ns
Note 1: The algebraic convention is used in this data sheet; the most negative value is shown in the minimum column.
Note 2: ∆RON = RON(max) - RON(min). On-resistance match between channels and on-resistance flatness are guaranteed only with
specified voltages. Flatness is defined as the difference between the maximum and minimum value of on-resistance as
measured over the specified analog signal range.
Note 3: Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at room temp.
Note 4: Guaranteed by design.
Note 5: Leakage testing at single supply is guaranteed by testing with dual supplies.
Note 6: See Figure 6. Off isolation = 20log10 VCOM/VNO, VCOM = output. NO = input to off switch.
Note 7: Between any two switches. See Figure 3.
6
_______________________________________________________________________________________
Serially Controlled, Low-Voltage,
8-Channel SPST Switch
(V+ = +3.0V to +3.6V, V- = 0V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
MIN
CONDITIONS
TYP
(Note 2)
MAX
V+
V
270
500
Ω
UNITS
ANALOG SWITCH
Analog Signal Range
COM, NO On-Resistance
NO Off Leakage Current
(Notes 4, 5)
COM Off Leakage Current
(Notes 4, 5)
COM On Leakage Current
(Notes 4, 5)
VCOM, VNO
RON
INO(OFF)
ICOM(OFF)
ICOM(ON)
C, E, M
V-
V+ = 3.0V, VCOM = 1.5V,
INO = 1mA
TA = +25°C
V+ = 3.0V, VCOM = 3V,
VNO = 0V
TA = +25°C
V+ = 3.6V, VCOM = 0V,
VNO = 3V
TA = +25°C
V+ = 3.6V, VCOM = 3V,
VNO = 0V
TA = +25°C
C, E, M
-5
V+ = 3.6V, VCOM = 0V,
VNO = 3V
TA = +25°C
0.1
V+ = 3.6V, VCOM = 3V,
VNO = 0V
TA = +25°C
C, E, M
-10
V+ = 3.6V, VCOM = 0V,
VNO = 3V
TA = +25°C
-0.1
C, E, M
-10
2.4
C, E, M
C, E, M
C, E, M
C, E, M
600
-0.1
0.002
0.1
0.002
0.1
0.002
0.1
0.002
0.1
0.002
0.1
0.002
0.1
-5
-0.1
5
-5
-0.1
5
5
-5
-0.1
nA
nA
5
10
nA
10
DIGITAL I/O
DIN, SCLK, CS, RESET Input
Voltage Logic Threshold High
VIH
C, E
DIN, SCLK, CS, RESET Input
Voltage Logic Threshold Low
VIL
C, E
V
0.8
V
1
µA
V
DIN, SCLK, CS, Input
Current Logic High or Low
IIH, IIL
VDIN, VSCLK,
V CS = 0.8V or 2.4V
C, E
-1
DOUT Output Voltage Logic High
VDOUT
IDOUT = 0.1mA
C, E, M
2.8
V+
DOUT Output Voltage Logic Low
VDOUT
IDOUT = -1.6mA
C, E, M
0
0.4
SCLK Input Hysteresis
SCLKHYST
0.03
C, E, M
100
TA = +25°C
260
V
mV
SWITCH DYNAMIC CHARACTERISTICS
600
Turn-On Time
tON
From rising edge of CS
Turn-Off Time
tOFF
From rising edge of CS
Break-Before-Make Delay
tBBM
From rising edge of CS
TA = +25°C
15
Charge Injection (Note 4)
VCTE
CL = 1nF, VNO = 0V, RS = 0Ω
TA = +25°C
2
Off Isolation (Note 6)
VISO
RL = 50Ω, CL = 15pF,
VNO = 1VRMS, f = 100kHz
TA = +25°C
-90
dB
Channel-to-Channel Crosstalk
(Note 7)
VCT
RL = 50Ω, CL = 15pF,
VNO = 1VRMS, f = 100kHz
TA = +25°C
<-90
dB
C, E, M
TA = +25°C
800
90
C, E, M
300
400
ns
ns
ns
10
pC
POWER SUPPLY
V+ Supply Current
I+
DIN = CS = SCLK = 0V or V+, TA = +25°C
RESET = 0V or 5V
C, E, M
6
20
30
µA
_______________________________________________________________________________________
7
MAX395
ELECTRICAL CHARACTERISTICS—Single +3V Supply
MAX395
Serially Controlled, Low-Voltage,
8-Channel SPST Switch
TIMING CHARACTERISTICS—Single +3V Supply (Figure 1)
(V+ = +3.0V to +3.6V, V- = 0V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SERIAL DIGITAL INTERFACE
SCLK Frequency
SYMBOL
MIN
CONDITIONS
TYP
(Note 2)
MAX
fSCLK
C, E, M
0
tCH + tCL
C, E, M
480
ns
CS Lead Time (Note 4)
tCSS
C, E, M
240
ns
CS Lag Time (Note 4)
tCSH2
C, E, M
240
ns
C, E, M
C, E, M
C, E, M
C, E, M
TA = +25°C
C, E, M
190
190
200
0
ns
ns
ns
ns
Cycle Time (Note 4)
2.1
UNITS
MHz
SCLK High Time (Note 4)
SCLK Low Time (Note 4)
Data Setup Time (Note 4)
Data Hold Time (Note 4)
tCH
tCL
tDS
tDH
DIN Data Valid after Falling SCLK
(Note 4)
tDO
50% of SCLK to 10% of
DOUT, CL = 10pF
Rise Time of DOUT (Note 4)
tDR
20% of V+ to 70% of V+,
CL = 10pF
C, E, M
300
ns
Allowable Rise Time at DIN,
SCLK (Note 4)
tSCR
20% of V+ to 70% of V+,
CL = 10pF
C, E, M
2
µs
Fall Time of DOUT (Note 4)
tDF
20% of V+ to 70% of V+,
CL = 10pF
C, E, M
300
ns
Allowable Fall Time at DIN,
SCLK (Note 4)
tSCF
20% of V+ to 70% of V+,
CL = 10pF
C, E, M
2
µs
RESET Minimum Pulse Width
tRW
TA = +25°C
38
-38
150
400
105
ns
ns
Note 1: The algebraic convention is used in this data sheet; the most negative value is shown in the minimum column.
Note 2: ∆RON = RON(max) - RON(min). On-resistance match between channels and on-resistance flatness are guaranteed only with
specified voltages. Flatness is defined as the difference between the maximum and minimum value of on-resistance as
measured over the specified analog signal range.
Note 3: Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at room temp.
Note 4: Guaranteed by design.
Note 5: Leakage testing at single supply is guaranteed by testing with dual supplies.
Note 6: See Figure 6. Off isolation = 20log10 VCOM/VNO, VCOM = output. NO = input to off switch.
Note 7: Between any two switches. See Figure 3.
8
_______________________________________________________________________________________
Serially Controlled, Low-Voltage,
8-Channel SPST Switch
ON-RESISTANCE vs. VCOM
AND TEMPERATURE
(DUAL SUPPLIES)
110
V± = ±2.5V
V± = ±5.5V
100
80
60
V± = ±5V
40
TA = +125°C
70
TA = +85°C
60
TA = +25°C
TA = -55°C
0
30
1
2
3
4
V+ = 5V
V+ = 9V
50
V+ = 12V
0
5
-5 -4 -3 -2 -1
0
1
2
3
4
0
5
4
2
6
8
VCOM (V)
VCOM (V)
ON-RESISTANCE vs. VCOM
AND TEMPERATURE
(SINGLE SUPPLY)
OFF-LEAKAGE vs.
TEMPERATURE
ON-LEAKAGE vs.
TEMPERATURE
TA = +125°C
V± = ±5.5V
120
TA = +25°C
100
80
TA = -55°C
125
1000
10
1
60
100
V± = ±5.5V
ON-LEAKAGE (pA)
OFF-LEAKAGE (pA)
TA = +85°C
12
10,000
100
140
10
MAX395 TOC6
1000
MAX395 TOC5
V+ = 5V
V- = 0V
160
V+ = 3V
VCOM (V)
MAX395 TOC4
180
0
200
100
40
-5 -4 -3 -2 -1
250
150
50
20
V- = 0V
300
80
RON (Ω)
RON (Ω)
V± = ±3V
RON (Ω)
V+ = 2.5V
350
90
100
100
10
1
40
0.1
2
3
4
0.1
-50
5
-25
VCOM (V)
CHARGE INJECTION vs. VCOM
0
25 50
75
TEMPERATURE (°C)
100
125
-50
250
MAX395 TOC7
5
A: V+ = 5V, V- = 5V
B: V+ = 5V, V- = 0V
tON, tOFF (ns)
1
0
-1
150
100
-2
B = tON
A = tON
B = tOFF
A = tOFF
-3
40
30
200
2
50
DATA HOLD TIME (ns)
3
0
25 50
75
TEMPERATURE (°C)
DATA HOLD TIME vs.
POWER-SUPPLY VOLTAGE
TURN-ON/OFF TIMES vs. VCOM
4
-25
MAX395 TOC9
1
MAX395 TOC8
0
Qj (pC)
RON (Ω)
400
MAX395 TOC2
120
MAX395 TOC1
140
ON-RESISTANCE vs. VCOM
(SINGLE SUPPLY)
MAX395 TOC3
ON-RESISTANCE vs. VCOM
(DUAL SUPPLIES)
20
10
0
-10
-20
-30
50
-40
-4
-5
-50
0
-5 -4 -3 -2 -1
0
1
VCOM (V)
2
3
4
5
-5 -4 -3 -2 -1
0
1
VCOM (V)
2
3
4
5
0
2
4
6
8
SUPPLY VOLTAGE (V)
_______________________________________________________________________________________
9
MAX395
__________________________________________Typical Operating Characteristics
(V+ = +5V, V- = -5V, GND = 0V, TA = +25°C, unless otherwise noted.)
____________________________Typical Operating Characteristics (continued)
(V+ = +5V, V- = -5V, GND = 0V, TA = +25°C, unless otherwise noted.)
POWER-SUPPLY CURRENT
vs. TEMPERATURE
90
80
35
MAX395 TOC11
100
MAX395 TOC10
100
MINIMUM SCLK PULSE WIDTH vs.
POSITIVE SUPPLY VOLTAGE
V± = ±5.5V
10
MAX395 TOC12
DATA SETUP TIME vs.
POSITIVE SUPPLY VOLTAGE
30
I+
60
50
40
SCLK (ns)
70
I+, I-, (µA)
DATA SETUP TIME (ns)
1
0.1
25
20
30
I-
0.01
20
15
10
0.001
0
4
2
6
10
-50
8
-25
SUPPLY VOLTAGE (V)
0
25
50
75
125
100
20
PHASE
-40
-100
10k
-60
OFF ISOLATION
-80
-80
-120
1M
10M
8
100M
V± = ±5V
600Ω IN AND OUT
1
0.1
-100
V± = ±5V
50Ω IN AND OUT
100k
6
10
TDH (%)
-20
ISOLATION OF
A BARE SOCKET
100
0
PHASE (DEGREES)
MAX395
TOC13
INSERTION LOSS
-60
4
TOTAL HARMONIC DISTORTION
vs. FREQUENCY
-20
-40
2
SUPPLY VOLTAGE (V)
FREQUENCY RESPONSE
0
0
TEMPERATURE (°C)
MAX395 TOC14
0
LOSS (dB)
MAX395
Serially Controlled, Low-Voltage,
8-Channel SPST Switch
1G
0.01
10
FREQUENCY (Hz)
100
1k
10k
FREQUENCY (Hz)
______________________________________________________________Pin Description
PIN
1
2
3
NAME
SCLK
V+
DIN
FUNCTION
Serial Clock Digital Input
Positive Analog Supply Voltage Input
Serial Data Digital Input
4
GND
Ground. Connect to digital ground. (Analog signals have no ground reference;
they are limited to V+ and V-.)
5, 7, 9, 11, 14, 16, 18, 20
6, 8, 10, 12, 13, 15, 17, 19
21
22
NO0–NO7
COM0–COM7
VDOUT
Normally Open Analog Switches 0–7
Common Analog Switches 0–7
Negative Analog Supply Voltage Input. Connect to GND for single-supply operation
Serial Data Digital Output. (High is sourced from V+.)
23
RESET
Reset Input. Connect to digital (logic) supply (or V+). Drive low to set all switches off and set internal shift registers to 0.
24
CS
Chip-Select Digital Input (Figure 1)
Note: NO_ and COM_ pins are identical and interchangeable. Either may be considered as an input or an output; signals pass
equally well in either direction.
10
______________________________________________________________________________________
Serially Controlled, Low-Voltage,
8-Channel SPST Switch
Basic Operation
The MAX395’s interface can be thought of as an 8-bit
shift register controlled by CS (Figure 2). While CS is
low, input data appearing at DIN is clocked into the
shift register synchronously with SCLK’s rising edge.
The data is an 8-bit word, each bit controlling one of
eight switches in the MAX395 (Table 1). DOUT is the
shift register’s output, with data appearing synchronously with SCLK’s falling edge. Data at DOUT is simply the input data delayed by eight clock cycles.
When shifting the input data, D7 is the first bit in and
out of the shift register. While shifting data, the switches
remain in their previous configuration. When the eight
bits of data have been shifted in, CS is driven high. This
updates the new switch configuration and inhibits further data from entering the shift register. Transitions at
DIN and SCLK have no effect when CS is high, and
DOUT holds the first input bit (D7) at its output.
More or less than eight clock cycles can be entered
during the CS low period. When this happens, the shift
register will contain only the last eight serial data bits,
regardless of when they were entered. On the rising
edge of CS, all the switches will be set to the corresponding states.
The MAX395’s three-wire serial interface is compatible
with SPI™, QSPI™, and Microwire™ standards. If interfacing with a Motorola processor serial interface, set
CPOL = 0. The MAX395 is considered a slave device
(Figures 2 and 3). Upon power-up, the shift register
contains all zeros, and all switches are off.
The latch that drives the analog switch is updated on
the rising edge of CS, regardless of SCLK’s state. This
meets all the SPI and QSPI requirements.
Daisy Chaining
For a simple interface using several MAX395s, “daisy
chain” the shift registers as shown in Figure 5. The CS
pins of all devices are connected together, and a
stream of data is shifted through the MAX395s in series.
When CS is brought high, all switches are updated
simultaneously. Additional shift registers may be included anywhere in series with the MAX395 data chain.
tCLL
CS
tCSH2
•••
tCSS
tCH
tOFF
tCSH0
•••
SCLK
tCL
tDS
tCSH1
tDH
•••
DIN
tDO
•••
DOUT
COM OUT
•••
Figure 1. Timing Diagram
______________________________________________________________________________________
11
MAX395
_______________Detailed Description
MAX395
Serially Controlled, Low-Voltage,
8-Channel SPST Switch
Addressable Serial Interface
When several serial devices are configured as slaves,
addressable by the processor, DIN pins of each
decode logic individually control CS of each slave
device. When a slave is selected, its CS pin is driven
low, data is shifted in, and CS is driven high to latch the
data. Typically, only one slave is addressed at a time.
DOUT is not used.
CS
SWITCHES
UPDATED
SCLK
__________Applications Information
Multiplexers
DIN
The MAX395 can be used as a multiplexer, but to
obtain the same electrical performance with slightly
improved programming speed, use the MAX349 8channel mux or the MAX350 dual 4-channel mux, both
in 18-pin packages.
D7 D6 D5 D4 D3 D2 D1 D0
DATA BITS
DOUT
D0
D7 D6 D5 D4 D3 D2 D1
D0
DATA BITS FROM PREVIOUS DATA INPUT
Figure 2. Three-Wire Interface Timing
Table 1. Serial-Interface Switch Programming
DATA BITS
RESET
12
FUNCTION
D7
D6
D5
D4
D3
D2
D1
D0
0
X
X
X
X
X
X
X
X
All switches open, D7–D0 = 0
1
0
X
X
X
X
X
X
X
Switch 7 open (off)
1
1
X
X
X
X
X
X
X
Switch 7 closed (on)
1
X
0
X
X
X
X
X
X
Switch 6 open (off)
1
X
1
X
X
X
X
X
X
Switch 6 closed (on)
1
X
X
0
X
X
X
X
X
Switch 5 open (off)
1
X
X
1
X
X
X
X
X
Switch 5 closed (on)
1
X
X
X
0
X
X
X
X
Switch 4 open (off)
1
X
X
X
1
X
X
X
X
Switch 4 closed (on)
1
X
X
X
X
0
X
X
X
Switch 3 open (off)
1
X
X
X
X
1
X
X
X
Switch 3 closed (on)
1
X
X
X
X
X
0
X
X
Switch 2 open (off)
1
X
X
X
X
X
1
X
X
Switch 2 closed (on)
1
X
X
X
X
X
X
0
X
Switch 1 open (off)
1
X
X
X
X
X
X
1
X
Switch 1 closed (on)
1
X
X
X
X
X
X
X
0
Switch 0 open (off)
1
X
X
X
X
X
X
X
1
Switch 0 closed (on)
______________________________________________________________________________________
Serially Controlled, Low-Voltage,
8-Channel SPST Switch
Dual, Differential 4-Channel Multiplexer
To use the MAX395 as a dual (4x2) mux, connect
COM0–COM3 together and connect COM4–COM7
together, forming the two outputs. The mux input pairs
become NO0/NO4, NO1/NO5, NO2/NO6, and NO3/NO7.
The mux can be programmed normally, with only one
differential channel selected for every eight clock pulses, or it can be programmed in a fast mode, where
channel changing occurs on each clock pulse.
In fast mode, the channels are selected by sending two
high pulses spaced four clock pulses apart (corresponding to the two selected channels) at DIN, and a
corresponding CS low pulse for each of the first eight
clock pulses. As this is clocked through the register by
SCLK
SK
MAX395 DIN
SO
DOUT
SI
DOUT
MISO
MAX395 DIN
MOSI
MICROWIRE
PORT
SCLK
I/O
CS
SPI
PORT
SCK
I/O
CS
CPOL = 0, CPHA = 0
THE DOUT-SI CONNECTION IS NOT REQUIRED FOR WRITING TO THE
MAX395, BUT MAY BE USED FOR DATA-ECHO PURPOSES.
THE DOUT-MISO CONNECTION IS NOT REQUIRED FOR WRITING TO THE
MAX395, BUT MAY BE USED FOR DATA-ECHO PURPOSES.
Figure 3. Connections for Microwire
SCLK
Figure 4. Connections for SPI and QSPI
SCLK
SCLK
MAX395
DIN
DIN
CS
CS
SCLK
MAX395
DOUT
DIN
CS
DOUT
MAX395
DIN
DOUT
CS
TO OTHER
SERIAL DEVICES
Figure 5. Daisy-Chained Connection
______________________________________________________________________________________
13
MAX395
8x1 Multiplexer
To use the MAX395 as an 8x1 multiplexer, connect all
common pins together (COM0–COM7) to form the mux
output; the mux inputs are NO0–NO7.
The mux can be programmed normally, with only one
channel selected for every eight clock pulses, or it can
be programmed in a fast mode, where channel changing occurs on each clock pulse. In this mode, the channels are selected by sending a single high pulse
(corresponding to the selected channel) at DIN, and a
corresponding CS low pulse for every eight clock pulses. As this is clocked through the register by SCLK,
each switch sequences one channel at a time, starting
with Channel 7.
MAX395
Serially Controlled, Low-Voltage,
8-Channel SPST Switch
DIN
SCLK
CS1
CS2
TO OTHER
SERIAL
DEVICES
CS3
CS
CS
CS
MAX395
MAX395
MAX395
SCLK
SCLK
SCLK
DIN
DIN
DIN
Figure 6. Addressable Serial Interface
Reset Function
D4
D0
SCLK
SW4
SW0
DIN
FOUR CLOCK
PULSES
Figure 7. Differential Multiplexer Input Control
SCLK, each switch sequences one differential channel
at a time, starting with channel 7/0. After the first eight
bits have been sent, subsequent channel sequencing
can occur by repeating this sequence or, even faster,
by sending only one DIN high pulse and one CS low
pulse for each four clock pulses.
SPDT Switches
To use the MAX395 as a quad, single-pole/doublethrow (SPDT) switch, connect COM0 to NO1, COM2 to
NO3, COM4 to NO5, and COM6 to NO7, forming the
four “common” pins. Program these four switches with
pairs of instructions, as shown in Table 2.
14
RESET is the internal reset pin. It is usually connected
to a logic signal or V+. Drive RESET low to open all
switches and set the contents of the internal shift register to zero simultaneously. When RESET is high, the
part functions normally and DOUT is sourced from V+.
RESET must not be driven beyond V+ or GND.
Power-Supply Considerations
Overview
The MAX395 construction is typical of most CMOS analog switches. It has three supply pins: V+, V-, and
GND. V+ and V- are used to drive the internal CMOS
switches and to set the limits of the analog voltage on
any switch. Reverse ESD-protection diodes are internally connected between each analog signal pin and
both V+ and V-. If any analog signal exceeds V+ or V-,
one of these diodes will conduct. During normal operation, these (and other) reverse-biased ESD diodes leak,
forming the only current drawn from V+ or V-.
Virtually all the analog leakage current is through the
ESD diodes. Although the ESD diodes on a given signal pin are identical, and therefore fairly well balanced,
they are reverse biased differently. Each is biased by
either V+ or V- and the analog signal. This means their
leakages vary as the signal varies. The difference in the
two diode leakages to the V+ and V- pins constitutes
the analog signal-path leakage current. All analog leak-
______________________________________________________________________________________
Serially Controlled, Low-Voltage,
8-Channel SPST Switch
DATA BITS
RESET
FUNCTION
D7
D6
D5
D4
D3
D2
D1
D0
0
X
X
X
X
X
X
X
X
All switches open, D7–D0 = 0
1
0
1
X
X
X
X
X
X
Switch 7 off and 6 on
1
1
0
X
X
X
X
X
X
Switch 6 off and 7 on
1
X
X
0
1
X
X
X
X
Switch 5 off and 4 on
1
X
X
1
0
X
X
X
X
Switch 4 off and 5 on
1
X
X
X
X
0
1
X
X
Switch 3 off and 2 on
1
X
X
X
X
1
0
X
X
Switch 2 off and 3 on
1
X
X
X
X
X
X
0
1
Switch 1 off and 0 on
1
X
X
X
X
X
X
1
0
Switch 0 off and 1 on
age current flows to the supply terminals, not to the
other switch terminal. This is why both sides of a given
switch can show leakage currents of either the same or
opposite polarity.
There is no connection between the analog signal
paths and GND.
V+ and GND power the internal logic and logic-level
translators, and set both the input and output logic limits. The logic-level translators convert the logic levels to
switched V+ and V- signals to drive the analog signal
gates. This drive signal is the only connection between
the logic supplies (and signals) and the analog supplies. V+, and V- have ESD-protection diodes to GND.
The logic-level inputs and output have ESD protection
to V+ and to GND.
The logic-level thresholds are CMOS and TTL compatible when V+ is +5V. As V+ is raised, the threshold
increases slightly. So when V+ reaches +12V, the
threshold is about 3.1V; slightly above the TTL guaranteed high-level minimum of 2.8V, but still compatible
with CMOS outputs.
Single Supply
The MAX395 operates from a single supply between
+3V and +16V when V- is connected to GND. All of the
bipolar precautions must be observed.
High-Frequency Performance
In 50Ω systems, signal response is reasonably flat up
to 50MHz (see Typical Operating Characteristics) .
Above 20MHz, the on-response has several minor
peaks that are highly layout dependent. The problem is
not turning the switch on, but turning it off. The off-state
switch acts like a capacitor and passes higher frequencies with less attenuation. At 10MHz, off isolation is
about -45dB in 50Ω systems, becoming worse (approximately 20dB per decade) as frequency increases.
Higher circuit impedances also make off isolation
worse. Adjacent channel attenuation is about 3dB
above that of a bare IC socket, and is due entirely to
capacitive coupling.
Bipolar Supplies
The MAX395 operates with bipolar supplies between
±3.0V and ±8V. The V+ and V- supplies need not be
symmetrical, but their sum cannot exceed the absolute
maximum rating of 17V. Do not connect the MAX395
V+ to +3V and connect the logic-level pins to TTL
logic-level signals. This exceeds the absolute maximum ratings and can damage the part and/or external circuits.
______________________________________________________________________________________
15
MAX395
Table 2. SPDT Switch Programming
MAX395
Serially Controlled, Low-Voltage,
8-Channel SPST Switch
___________________Chip Topography
COM5
NO5
NO3
NO2
COM4
COM3
COM2
NO4
COM1
COM6
NO6
NO1
0.120"
COM0 (3.05mm)
COM7
NO7
NO0
GND
V-
DOUT
RESET
CS
V+
SCLK
DIN
0.100"
(2.54mm)
TRANSISTOR COUNT: 500
SUBSTRATE CONNECTED TO V+.
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
16 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600
© 1995 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.