ETC 6ES7222-1BF20-0XA0

S7-200 Specifications
A.6
Table A-6
Specifications for the EM222 Digital Output Modules
Specifications for EM222 24 VDC Output and Relay Output Modules
Description
Order Number
EM222 24 VDC Output
6ES7 222–1BF20–0XA0
EM222 Relay Output
6ES7 222–1HF20–0XA0
Physical Size
Dimensions (W x H x D)
46 x 80 x 62 mm
46 x 80 x 62 mm
Weight
150 g
170 g
Power loss (dissipation)
2W
2W
Number of outputs
8 points
8 points
Output type
Solid state–MOSFET
Relay, dry contact
Permissible range
20.4 to 28.8 VDC
5 to 30 VDC, or 5 to 250 VAC
Rated value
24 VDC
–
Logic 1 signal at maximum current
20 VDC, minimum
–
Logic 0 signal with 10 K Ω load
0.1 VDC, maximum
–
Logic 1 signal
0.75 A
2.00 A
Number of outputs groups
2
2
Number of outputs on (maximum)
8
8
Per group – horizontal mounting (maximum)
4
4
Per group – vertical mounting (maximum)
4
4
Maximum current per common/group
3A
8A
Lamp load
5W
30 W DC/200 W AC
ON state resistance (contact resistance)
0.3 Ω
0.002 Ω, maximum when new
Leakage current per point
10 µA, maximum
–
Surge current
8 A for 100 ms, maximum
7 A with contacts closed
Overload protection
No
No
Optical isolation (galvanic)
500 VAC for 1 minute
–
Isolation resistance
–
100 M Ω, minimum when new
Isolation coil to contact
–
1500 VAC for 1 minute
Isolation between open contacts
–
750 VAC for 1 minute
In groups of
4 points
4 points
1 W, all channels
–
L+ minus 48 V
–
50 µs, maximum
–
Output Features
Output Voltage
Output Current
Isolation
Inductive Load Clamping
Repetitive
Energy dissipation
< 0.5 LI2 x switching rate
Clamp voltage limits
Output Delay
Off to On
200 µs, maximum
–
Switching delay
–
10 ms, maximum
Lifetime mechanical (no load)
–
10,000,000 open/close cycles
Lifetime contacts at rated load
–
100,000 open/close cycles
Unshielded
150 m
150 m
Shielded
500 m
500 m
From +5 VDC (from I/O bus)
50 mA
40 mA
From L+
–
9 mA per output when ON
L+ coil power voltage range
–
20.4 to 28.8 VDC
On to Off
Relay
Cable Length
Power Consumption
S7-200 Programmable Controller System Manual
C79000-G7076-C233-01
A-23
S7-200 Specifications
+
24 VDC Commons and
24 VDC Output
Terminals
1M
1L+ .0
Note:
1. Actual component values may vary.
2. Optional ground.
.1
.2
.3
.5
.6
.7
36V
2M
24 VDC Commons and
24 VDC Output
Terminals
2L+ .4
+
Figure A-9
Connector Terminal Identification for EM222 Digital Output 8 x 24 VDC
N (–)
L (+)
24 VDC Power
Commons and Relay
Output Terminals
Note:
1. Actual component values may vary.
2. Connect AC line to the L terminal.
3. Optional ground.
4. Relay coil power M must connect
to sensor supply M of CPU.
M
L+
1L
.0
.1
.2
.3
2L
.4
.5
.6
.7
Commons and Relay
Output Terminals
N (–)
+
L (+)
Coil Power Figure A-10
A-24
Connector Terminal Identification for EM222 Digital Output 8 x Relay
S7-200 Programmable Controller System Manual
C79000-G7076-C233-01