MICROCIRCUIT DATA SHEET Original Creation Date: 11/24/98 Last Update Date: 03/09/99 Last Major Revision Date: 2/16/99 MNCLC400A-X REV 2A0 FAST SETTLING, WIDEBAND LOW-GAIN MONOLITHIC OP AMP General Description The CLC400 is a high-speed, fast-settling operational amplifier designed for low-gain applications. Constructed using a unique, proprietary design and an advanced complementary bipolar process, the CLC400 offers performance far beyond that normally offered by ordinary monolithic operational amplifiers. In addition, unlike many other high-speed operational amplifiers the CLC400 offers both high performance and stability without the need for compensation circuitry - even at a gain of +1. The fast 12ns settling to 0.05% and its ability to drive capacitive loads makes the CLC400 an ideal flash A/D driver. The wide bandwidth of 200 MHz and the very linear phase ensure unsurpassed signal fidelity. Systems employing digital to analog converters also benefit from the use of the CLC400 - especially if linearity and drive levels are important to system performance. The CLC400 provides a simple, high-performance solution for video distribution and line driving applications. The 50mA output current and guaranteed specifications for 100 ohm loads provide ample drive capability and assured performance. Industry Part Number NS Part Numbers CLC400A CLC400AE-QML* CLC400AJ-MLS CLC400AJ-QML** Prime Die UB1363B Controlling Document 5962-8997001PA**, 2A* Processing Subgrp Description MIL-STD-883, Method 5004 1 2 3 4 5 6 7 8A 8B 9 10 11 Quality Conformance Inspection MIL-STD-883, Method 5005 1 Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Switching tests at Switching tests at Switching tests at Temp ( oC) +25 +125 -55 +25 +125 -55 +25 +125 -55 +25 +125 -55 MICROCIRCUIT DATA SHEET MNCLC400A-X REV 2A0 Features - -3dB bandwidth of 270MHz - 0.05% settling in 12ns - Low power, 150mW - Low distortion, -60dBc at 20MHz - Stable without compensation - Overload and short circuit protection - +1 to +8 closed-loop gain range Applications - Flash, precision A/D conversion Photodiode, CCD preamps IF processors High-speed communications Line drivers Video distribution High-speed communications 2 MICROCIRCUIT DATA SHEET MNCLC400A-X REV 2A0 (Absolute Maximum Ratings) (Note 1) Supply Voltage (Vs) +7V dc Output Current (Iout) +70mA Maximum Power Dissipation (Pd) (Note 2) 1.2W Junction Temperature (Tj) +175 C Storage Temperature Range -65 C to +150 C Lead Temperature (soldering, 10 seconds) +300 C Thermal Resistance Junction-to-ambient (ThetaJA) Ceramic DIP (Still Air) (500 LFPM) LCC (Still Air) (500 LFPM) Junction-to-case (ThetaJC) Ceramic DIP LCC Package Weight (typical) Ceramic DIP LCC ESD Tolerance (Note 3) ESD Rating Note 1: Note 2: Note 3: 134 C/W 82 C/W TBD TBD 28 C/W TBD 1070 mg TBD 1000 V Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. The maximum power dissipation must be derated at elevated temperatures and is dictated by Tjmax (maximum junction temperature), ThetaJA (package junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is Pdmax = (Tjmax - TA)/ThetaJA or the number given in the Absolute Maximum Ratings, whichever is lower. Human body model, 100pF discharged through 1.5K Ohms. Recommended Operating Conditions Supply Voltage (Vs) +5V dc Closed Loop Gain Range +1 to +8 Ambient Operating Temperature Range (Ta) -55 C to +125 C 3 MICROCIRCUIT DATA SHEET MNCLC400A-X REV 2A0 Electrical Characteristics DC PARAMETERS: Open Loop Characteristics (The following conditions apply to all the following parameters, unless otherwise specified.) DC: Rl = 100 Ohms, Vs = +5V dc. -55 C < Ta < +125 C (Note 3) SYMBOL +Iin -Iin Vio PARAMETER CONDITIONS Input Bias Current (noninverting) RS = 50Ohm Input Bias Current (Inverting) RS = 50Ohm Input Offset Voltage RS = 50Ohm ROL Transimpedance TA = +25C IS Supply Current No Load PSRR Power Supply Rejection Ratio +VS = +4.5V to +5.5V -VS = -4.5V to -5.5V +RIN Input Resistance Iout CMRR Vout NOTES 1 Output Voltage Swing MIN MAX UNIT SUBGROUPS -20 +20 uA 1, 2 -36 +36 uA 3 -20 +20 uA 1 -30 +30 uA 2 -36 +36 uA 3 -5 5 mV 1 -9 9 mV 2 -8.2 8.2 mV 3 30 V/mA 1 +23 mA 1, 2, 3 45 dB 1, 2, 3 1 100 kOhm 1, 2 1 50 kOhm 3 1 50 mA 1, 2 1 355 mA 3 VCM = +2.0V 1 45 dB 1 VCM = +1.2V 1 45 dB 2, 3 No Load 1 2.8 V 1, 2 1 2.3 V 3 Output Current Common Mode Rejection Ratio PINNAME 4 MICROCIRCUIT DATA SHEET MNCLC400A-X REV 2A0 Electrical Characteristics AC PARAMETERS: Closed Loop Characteristics (The following conditions apply to all the following parameters, unless otherwise specified.) AC: Rl = 100 Ohms, Rf = 250 Ohms, Vs = +5V dc, and Av = +2. -55 C < Ta < +125 C (Note 3) SYMBOL SSBW GFPL PARAMETER Small Signal Bandwidth Gain Flatness Peaking CONDITIONS NOTES -3dB bandwidth, Vout < 0.5VPP PINNAME MIN Gain Flatness Peaking HD2 HD3 Gain Flatness Rolloff 2nd Harmonic Distortion 3rd Harmonic Distortion SUBGROUPS MHz 4 2 120 MHz 5 2 150 MHz 6 0.3 dB 4 0.4 dB 5, 6 0.5 dB 4 0.7 dB 5, 6 1.0 dB 4 2 1.3 dB 5 2 1.0 dB 6 -45 dB 4 2 -45 dB 5 2 -40 dB 6 -50 dB 4 -50 dB 5, 6 .1 to 40 MHz No peaking over 40MHz 2 GFR UNIT 150 2 GFPH MAX .1 to 75 MHz 2 VPP at 20 MHz 2 VPP at 20 MHz 2 AC PARAMETERS: Time Domain Response (The following conditions apply to all the following parameters, unless otherwise specified.) AC: Rl = 100 Ohms, Rf = 250 Ohms, Vs = +5V dc. -55 C < Ta < +125 C (Note 3) SR Slew Rate Av= +2, measured +1V with +3V step 1 TRS Rise Time 0.5V Step 1 2.4 nS 9, 10, 11 TRL Fall Time 5V Step 1 10 nS 9, 10, 11 TS Settling Time 2V Step at 0.1% of fixed value 1 13 nS 9, 10, 11 2V Step at 0.05% of fixed value 1 15 nS 9, 10, 11 0.5V Step 1 10 % 9 1 15 % 10, 11 OS Overshoot 5 430 V/uS 9, 10, 11 MICROCIRCUIT DATA SHEET MNCLC400A-X REV 2A0 Electrical Characteristics DC PARAMETERS: Drift Values (The following conditions apply to all the following parameters, unless otherwise specified.) DC: Rl = 100 Ohms, Vs = +5V dc. -55 C < Ta < +125 C "Deltas not required on B-Level product. Deltas required for S-Level (-MLS) product as specified on Internal Processing Instructions (IPI)." (Note 3) SYMBOL PARAMETER CONDITIONS NOTES PINNAME MIN MAX UNIT SUBGROUPS +Iin Input Bias Current (noninverting) Rs = 50Ohm -1.5 1.5 uA 1 -Iin Input Bias Current (inverting) Rs = 50Ohm -1.5 1.5 uA 1 Vio Input Offset Voltage Rs = 50Ohms -1.0 1.0 mV 1 IS Supply Current No Load -2.0 2.0 mA 1 Note 1: Note 2: Note 3: If not tested, shall be guaranteed to the limits specified in Table 1 Group A testing only. The algebraic convention, whereby the most negative value is a minimum and most positive is a maximum, is used in this table. Negative current shall be defined as convential current flow out of a device terminal. 6 MICROCIRCUIT DATA SHEET MNCLC400A-X REV 2A0 Graphics and Diagrams GRAPHICS# DESCRIPTION 07081HRA3 CERDIP (J), 8 LEAD (B/I CKT) 07086HRA2 LCC (E), TYPE C, 20 TERMINAL (B/I CKT) E20ARE LCC (E), TYPE C, 20 TERMINAL(P/P DWG) J08ARL CERDIP (J), 8 LEAD (P/P DWG) P000427A CERDIP (J), 8 LEAD (PINOUT) P000445A LCC (E), TYPE C, 20 TERMINAL (PINOUT) See attached graphics following this page. 7 Offset Adjust 1 8 N/C VINV 2 7 +VCC VNON-INV 3 6 VOUT -VCC 4 5 N/C CLC400J 8 - LEAD DIP CONNECTION DIAGRAM TOP VIEW P000427A N MIL/AEROSPACE OPERATIONS 2900 SEMICONDUCTOR DRIVE SANTA CLARA, CA 95050 OFF ADJ 4 N/C N/C N/C 3 2 N/C N/C N/C 1 20 19 18 N/C 5 17 N/C V- 6 16 +VCC N/C 7 15 N/C V+ 8 14 VO 9 -VCC 10 11 12 13 N/C N/C N/C N/C CLC400E 20 - LEAD LCC CONNECTION DIAGRAM TOP VIEW P000445A N MIL/AEROSPACE OPERATIONS 2900 SEMICONDUCTOR DRIVE SANTA CLARA, CA 95050 MICROCIRCUIT DATA SHEET MNCLC400A-X REV 2A0 Revision History Rev ECN # Originator Changes 0A0 M0003157 02/18/99 Rel Date Shaw Mead Initial MDS Release 1A0 M0003241 03/09/99 Shaw Mead Thermal data for Ceramic DIP added. Package weight for Ceramic DIP added. Gain Range in Recommended Op. Cond. corrected. CMRR subgroups corrected. Closed loop gain in AC conditions corrected. Rf = 250 Ohms added to AC conditions. 2A0 M0003273 03/09/99 Shaw Mead Processing and QCI document reference added. Conditions for SR added. 8