MICROCIRCUIT DATA SHEET Original Creation Date: 04/07/98 Last Update Date: 08/02/01 Last Major Revision Date: 07/18/01 MNCLC420B-X REV 3A0 HIGH SPEED, VOLTAGE FEEDBACK OPERATIONAL AMPLIFIER General Description The CLC420B is an operational amplifier designed for applications requiring matched inputs and integration or transimpedance amplification. Utilizing voltage feedback architecture, the CLC420B offers a 300MHz bandwidth, a 1100V/us slew rate and a 4mA supply current (power consumption of 40mW, +5V supplies). Additional benefits of the CLC420B are a 0.5mV input offset voltage and a 4uV/C temperature coefficient. Applications such as differential amplifiers will benefit from 70dB common mode rejection ratio and an input offset current of 0.2uA(typ). With its unity-gain stability, 2pA/SqRtHz current noise(typ), combined with a settling time of 18ns to 0.01% make the CLC420B ideal for D/A converters, pin diode receivers and photo multiplier amplifiers. All applications will find 70dB power supply rejection ratio attractive. Industry Part Number NS Part Numbers CLC420B CLC420BE-QML CLC420BJ-QML Prime Die UB1366A Controlling Document SEE FEATURES SECTION Processing Subgrp Description MIL-STD-883, Method 5004 1 2 3 4 5 6 7 8A 8B 9 10 11 Quality Conformance Inspection MIL-STD-883, Method 5005 1 Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Switching tests at Switching tests at Switching tests at Temp ( oC) +25 +125 -55 +25 +125 -55 +25 +125 -55 +25 +125 -55 MICROCIRCUIT DATA SHEET MNCLC420B-X REV 3A0 Features - 300MHz small signal bandwidth 1100V/us slew rate Unity-gain stability Low distortion, -60dBc at 20MHz 0.01% settling in 18ns 0.2uA input offset current 2pASqRtHz current noise 0.5mV input offset voltage, 4uV/C CONTROLLING DOCUMENTS: CLC420BE-QML 5962-9175802M2A CLC420BJ-QML 5962-9175802MPA Applications - Active filters/integrators Differential amplifiers Pin diode receivers Log amplifiers D/A converters Photo multiplier amplifiers 2 MICROCIRCUIT DATA SHEET MNCLC420B-X REV 3A0 (Absolute Maximum Ratings) (Note 1) Supply Voltage (V+) +7 Vdc Output Current (Iout) 70 mA Common Mode Input Voltage (Vcm) V+ Differential Input Voltage 10 V Power Dissipation (Pd) (Note 2) 112 mW Thermal Resistance (ThetaJA) Junction to Ambient Ceramic DIP LCC (Still Air) (500 LFPM) (Still Air) (500 LFPM) (ThetaJC) Junction to Case Ceramic DIP LCC Junction Temperature (Tj) 125 72 100 68 C/W C/W C/W C/W 23 C/W 25 C/W +175 C Storage Temperature Range -65 C < Ta < +150 C Lead Temperature (Soldering, 10 seconds) Package Weight (Typical) Ceramic DIP LCC ESD Tolerance (Note 3) ESD Rating Note 1: Note 2: Note 3: +300 C 1075 mg 470 mg 2000V Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. The maximum power dissipation must be derated at elevated temperatures and is dictated by Tjmax (maximum junction temperature), ThetaJA (package junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is Pdmax = (Tjmax - TA)/ThetaJA or the number given in the Absolute Maximum Ratings, whichever is lower. Human body model, 100pF discharged through 1.5K Ohms. 3 MICROCIRCUIT DATA SHEET MNCLC420B-X REV 3A0 Recommended Operating Conditions Supply Voltage (V+) +5 Vdc Gain Range (Av) +1 to +10 Operating Temperature Range -55 C < Ta < +125 C 4 MICROCIRCUIT DATA SHEET MNCLC420B-X REV 3A0 Electrical Characteristics DC PARAMETERS: Open Loop Characteristics (The following conditions apply to all the following parameters, unless otherwise specified.) DC: V+ = +5 Vdc, Av = +1, Load Resistance Rl = 100 Ohms, tested parameters use Rs = 500 Ohms, otherwise, feedback resistance (Rf) = 0 Ohms. Temp. Range: -55 C < TA < +125 C. (Note 3) SYMBOL +Iin -Iin Vio Tc (+Iin) PARAMETER CONDITIONS NOTES PINNAME MIN MAX UNIT SUBGROUPS Input Bias Current (NonInverting) -10 +10 uA 1, 2 -20 +20 uA 3 Input Bias Current (Inverting) -10 +10 uA 1, 2 -20 +20 uA 3 Input Offset Voltage -0.8 +0.8 mV 1 -1.8 +1.8 mV 2 -1.6 +1.6 mV 3 Average +Input Bias Current Drift 1 60 nA/C 2 1 120 nA/C 3 Average -Input Bias Current Drift 1 60 nA/C 2 1 120 nA/C 3 Tc (Vio) Average Input Offset Voltage Drift 1 10 uV/C 2, 3 Iio Input Offset Current -1.0 1.0 uA 1 -2.0 2.0 uA 2 -3.0 3.0 uA 3 1 10 nA/C 2 1 20 nA/C 3 Tc (-Iin) Tc (Iio) Aol Average Input Offset Current Drift Open Loop Gain Icc Quiescent Supply Current (No Load) PSRR Power Supply Rejection Ratio CMRR Rind Cind Common Mode Rejection Ratio 56 dB 1, 2 52 dB 3 mA 1, 2, 3 60 dB 1, 2 55 dB 3 65 dB 1, 2 60 dB 3 1 1 MOhm 4, 5 1 0.5 MOhm 6 5.0 V+ = +4.5V to +5.0V, V- = -4.5V to -5.0V Vcm = +1V Differential Mode Input Resistance Differential Mode Input Capacitance 1 5 2 pF 4, 5, 6 MICROCIRCUIT DATA SHEET MNCLC420B-X REV 3A0 Electrical Characteristics DC PARAMETERS: Open Loop Characteristics (Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: V+ = +5 Vdc, Av = +1, Load Resistance Rl = 100 Ohms, tested parameters use Rs = 500 Ohms, otherwise, feedback resistance (Rf) = 0 Ohms. Temp. Range: -55 C < TA < +125 C. (Note 3) SYMBOL Rinc PARAMETER CONDITIONS NOTES Common Mode Input Resistance 0.25 MOhm 6 Common Mode Input Voltage 1 1 -Iout Rout +Vo Output Current Output Impedance Output Voltage Swing At dc No Load Rl = 100 Ohms -Vo Output Voltage Swing No Load Rl = 100 Ohms 6 SUBGROUPS 1 +Vcm Output Current UNIT MOhm 4, 5 1 +Iout MAX 0.5 Common Mode Input Capacitance Common Mode Input Voltage MIN 1 Cinc -Vcm PINNAME 2 pF 4, 5, 6 +2.8 V 4, 5 +2.5 V 6 1 -2.8 V 4, 5 1 -2.5 V 6 1 +50 mA 4, 5 1 +30 mA 6 1 -50 mA 4, 5 1 -30 mA 6 1 0.2 Ohm 4, 5 1 0.3 Ohm 6 +3 V 1, 2 +2.8 V 3 +2.5 V 1, 2, 3 -3 V 1, 2 -2.8 V 3 -2.5 V 1, 2 -2.2 V 3 MICROCIRCUIT DATA SHEET MNCLC420B-X REV 3A0 Electrical Characteristics AC PARAMETERS: Frequency Domain Response (The following conditions apply to all the following parameters, unless otherwise specified.) AC: V+ = +5 Vdc, Av = +1, Load Resistance Rl = 100 Ohms, tested parameters use Rs = 500 Ohms, otherwise, feedback resistance (Rf) = 0 Ohms. Temp. Range: -55 C < TA < +125 C. (Note 3) SYMBOL GFPL GFPH GFR PARAMETER Gain Flatness Peaking Low Gain Flatness Peaking High Gain Flatness Rolloff CONDITIONS NOTES PINNAME MIN At 0.1 MHz to 100 MHz, Vout < 0.4 Vpp At 100 MHz, Vout < 0.4 Vpp At 0.1 MHz to 100 MHz, Vout < 0.4 Vpp At 0.1 MHz to 30 MHz, Av = -1, Rf = 500 Ohms, Vout < 0.4 Vpp SSBW Small Signal Bandwidth -3dB bandwidth, Vout < 0.4 Vpp Large Signal Bandwidth -3dB bandwidth, Vout < 5Vpp -3dB bandwidth, Av = -1, Rf = 500 Ohms, Vout < 5 Vpp Lpd Linear Phase Deviation At 0.1 MHz to 100 MHz 7 UNIT SUBGROUPS 1.4 dB 4 1.6 dB 5 1.4 dB 6 3.0 dB 4 3.0 dB 5 5.0 dB 6 1.0 dB 4, 6 2.0 dB 5 1.4 dB 4 1.6 dB 5 1.4 dB 6 1 200 MHz 4, 6 1 130 MHz 5 65 MHz 4 65 MHz 6 45 MHz 5 1 25 MHz 4 1 20 MHz 5, 6 1 35 MHz 4 1 30 MHz 5, 6 -3dB bandwidth, Av = -1, Rf = 500 Ohms, Vout < 0.4 Vpp LSBW MAX 1 1.8 Deg. 4, 6 1 2.5 Deg. 5 MICROCIRCUIT DATA SHEET MNCLC420B-X REV 3A0 Electrical Characteristics AC PARAMETERS: Distortion and Noise (The following conditions apply to all the following parameters, unless otherwise specified.) AC: V+ = +5 Vdc, Av = +1, Load Resistance Rl = 100 Ohms, tested parameters use Rs = 500 Ohms, otherwise, feedback resistance (Rf) = 0 Ohms. Temp. Range: -55 C < TA < +125 C. (Note 3) SYMBOL HD2 PARAMETER 2nd Harmonic Distortion CONDITIONS NOTES 2 Vpp at 20 MHz 2 Vpp at 20 MHz, Av = -1 HD3 3rd Harmonic Distortion 2 Vpp at 20 MHz 2 Vpp at 20 MHz, Av = -1 Vn Icn Input Referred Noise Voltage Input Referred Noise Current At 1 MHz to 200 MHz 1 At 1 MHz to 200 MHz PINNAME MIN MAX UNIT -40 dBc 4 -40 dBc 5, 6 -40 dBc 4 -40 dBc 5, 6 -45 dBc 4, 6 -40 dBc 5 -40 dBc 4 -35 dBc 5 -40 dBc 6 5.3 nV/sq 4, 6 1 6 rtHz nV/sq 5 1 2.6 rtHz pA/sq 4 1 2.3 rtHz pA/sq 5 1 2.9 rtHz pA/sq 6 rtHz 8 SUBGROUPS MICROCIRCUIT DATA SHEET MNCLC420B-X REV 3A0 Electrical Characteristics AC PARAMETERS: Time Domain Response (The following conditions apply to all the following parameters, unless otherwise specified.) AC: V+ = +5 Vdc, Av = +1, Load Resistance Rl = 100 Ohms, tested parameters use Rs = 500 Ohms, otherwise, feedback resistance (Rf) = 0 Ohms. Temp. Range: -55 C < TA < +125 C. (Note 3) SYMBOL Trs Trl Ts Os +Sr -Sr PARAMETER Rise and Fall Time Rise and Fall Time Settling Time Overshoot Slew Rate Slew Rate CONDITIONS NOTES 0.4 V step, Cl < 10pF, measured between 10% and 90% points MIN MAX UNIT SUBGROUPS 1 2 nS 9, 11 1 3 nS 10 0.4 V step, Av = -1, Rf = 500 Ohms, Cl < 10 pF, measured between 10% and 90% points 1 5.5 nS 9, 11 1 7.8 nS 10 5 V step Cl < 10 pF, measured between 10% and 90% points 1 20 nS 9, 10 1 25 nS 11 5 V step, Av = -1, Rf = 500 Ohms, Cl < 10 pF, measured between 10% and 90% points 1 9.5 nS 9 1 10 nS 10, 11 2V step at 0.01% of the final value, Cl < 10 pF 1 25 nS 9, 10, 11 2V step at 0.1% of the final value, Cl < 10 pF 1 18 nS 9, 10, 11 0.4 V step, Cl < 10 pF 1 25 % 9, 10 1 35 % 11 Rising edge, Measured +1 V with 5 V step, Cl < 10 pF 1 750 V/uS 9 1 600 V/uS 10, 11 Rising edge, Av = -1, Measured +1 V with 5 V step, Rf = 500 Ohms, Cl = < 10 pF 1 500 V/uS 9 1 430 V/uS 10, 11 Falling Edge, Measured +1 V with 5 V step, Cl < 10 pF 1 750 V/uS 9 1 600 V/uS 10, 11 1 500 V/uS 9 1 430 V/uS 10, 11 Falling Edge, Av = -1, Measured +1 V with 5 V step, Rf = 500 Ohms, Cl < 10 pF Note 1: Note 2: Note 3: PINNAME If not tested, shall be guaranteed to the limits specified. Group A testing only. The algebraic convention, whereby the most negative value is a minimum and the most positive is a maximum, is used in this table. Negative current shall be defined as conventional flow out of a device terminal. 9 MICROCIRCUIT DATA SHEET MNCLC420B-X REV 3A0 Graphics and Diagrams GRAPHICS# DESCRIPTION 07081HRA3 CERDIP (J), 8 LEAD (B/I CKT) 07086HRA2 LCC (E), TYPE C, 20 TERMINAL (B/I CKT) E20ARE LCC (E), TYPE C, 20 TERMINAL(P/P DWG) J08ARL CERDIP (J), 8 LEAD (P/P DWG) P000430A CERDIP (J), 8 LEAD (PINOUT) P000444A LCC (E), TYPE C, 20 TERMINAL (PINOUT) See attached graphics following this page. 10 N/C 1 8 N/C VINV 2 7 +VCC VNON-INV 3 6 VOUT -VCC 4 5 N/C CLC420J 8 - LEAD DIP CONNECTION DIAGRAM TOP VIEW P000430A N MIL/AEROSPACE OPERATIONS 2900 SEMICONDUCTOR DRIVE SANTA CLARA, CA 95050 N/C 4 N/C N/C N/C 3 2 N/C N/C N/C 1 20 19 18 N/C 5 17 N/C VINV 6 16 +VCC N/C 7 15 N/C VNON-INV 8 14 VOUT 9 -VCC 10 11 12 13 N/C N/C N/C N/C CLC420E 20 - LEAD LCC CONNECTION DIAGRAM TOP VIEW P000444A N MIL/AEROSPACE OPERATIONS 2900 SEMICONDUCTOR DRIVE SANTA CLARA, CA 95050 MICROCIRCUIT DATA SHEET MNCLC420B-X REV 3A0 Revision History Rev ECN # Originator Changes 0A0 M0003231 10/20/99 Rel Date Shaw Mead Initial MDS Release -TRL typo corrected. 0B0 M0003581 05/22/00 Rose Malone Updated missing information on Main Table, adding reference to 883 spec MIL-STD to Processing and Quality Conformance Inspection sections and Note 1 in electrical section. MNCLC420B-X, Rev. 0A0 to MNCLC420B-X, Rev. 0B0 1A0 M0003705 07/11/01 Rose Malone Update MDS: MNCLC420B-X, Rev. 0B0 to MNCLC420B-X, Rev. 1A0. Added Min. limits to Iio test and changed Subgroup 3 test limit from 2.6uA to 3.0uA to improve test yields. 2A0 M0003812 08/02/01 Rose Malone Update MDS: MNCLC420B-X-RH, Rev. 1A0 to MNCLC420B-X-RH, Rev. 2A0. Change to Electrical Section, typo in Vn parameter units change from mV/Hz to nV/sqrtHz 3A0 M0003829 08/02/01 Rose Malone Update MDS: MNCLC420B-X, Rev. 2A0 to MNCLC420B-X, Rev. 3A0. Electrical Section Icn parameter units column from pA/Hz to pA/sqrtHz. 11