DCR1476SY / DCR1476SV DCR1476SY / DCR1476SV Phase Control Thyristor Advance Information Replaces July 2001 version, DS4647-6.0 DS4647-7.0 October 2003 KEY PARAMETERS PACKAGE OUTLINE Outline type code: Y VDRM 3800V IT(AV) 2223A ITSM 36250A dVdt 1000V/µs dI/dt 300A/µs Outline type code: V See Package Details for further information. Fig. 1 Package outline VOLTAGE RATINGS Part Number Repetitive Peak Voltages VDRM VRRM Conditions V DCR1476SY38 or DCR1476SV38 3800 3800 Tvj = 0˚ to 125˚C. IDRM = IRRM = 300mA. VDRM, VRRM = 10ms 1/2 sine. VDSM & VRSM = VDRM & VRRM + 100V respectively. Lower voltage grades available. ORDERING INFORMATION When ordering select the required part number shown in the Voltage Ratings selection table. For example: DCR1476SY38 for a 3800V 'Y' outline variant or DCR1476SV38 for a 3800V 'V' outline variant If a lower voltage grade is required, then use VDRM/100 for the grade required e.g.: DCR1476SY30 for a 3000V 'Y' outline variant etc. Note: Please use the complete part number when ordering and quote this number in any future correspondance relating to your order. 1/9 www.dynexsemi.com DCR1476SY / DCR1476SV CURRENT RATINGS Tcase = 60˚C unless stated otherwise. Symbol Parameter Conditions Max. Units 2223 A Double Side Cooled Half wave resistive load IT(AV) Mean on-state current IT(RMS) RMS value - 3492 A Continuous (direct) on-state current - 3287 A 1479 A IT Single Side Cooled (Anode side) IT(AV) Mean on-state current IT(RMS) RMS value - 2323 A Continuous (direct) on-state current - 2035 A Conditions Max. Units 1770 A IT Half wave resistive load CURRENT RATINGS Tcase = 80˚C unless stated otherwise. Symbol Parameter Double Side Cooled Half wave resistive load IT(AV) Mean on-state current IT(RMS) RMS value - 2780 A Continuous (direct) on-state current - 2530 A 1170 A IT Single Side Cooled (Anode side) IT(AV) Mean on-state current IT(RMS) RMS value - 1837 A Continuous (direct) on-state current - 1590 A IT Half wave resistive load 2/9 www.dynexsemi.com DCR1476SY / DCR1476SV SURGE RATINGS Parameter Symbol ITSM I2t ITSM I2t Surge (non-repetitive) on-state current I2t for fusing Surge (non-repetitive) on-state current Conditions Max. Units 10ms half sine; Tcase = 125oC 29.0 kA VR = 50% VRRM - 1/4 sine 4.21 x 106 A2s 10ms half sine; Tcase = 125oC 36.25 kA VR = 0 6.57 x 106 A2s I2t for fusing THERMAL AND MECHANICAL DATA Min. Max. dc - 0.0095 o Anode dc - 0.019 o Cathode dc - 0.019 o C/W Double side - 0.002 o C/W Single side - 0.004 o C/W On-state (conducting) - 135 o Reverse (blocking) - 125 o Storage temperature range –55 125 o Clamping force 38.0 47.0 Parameter Symbol Conditions Double side cooled Rth(j-c) Thermal resistance - junction to case Units C/W C/W Single side cooled Rth(c-h) Tvj Tstg - Thermal resistance - case to heatsink Clamping force 43.0kN with mounting compound C Virtual junction temperature C C kN 3/9 www.dynexsemi.com DCR1476SY / DCR1476SV DYNAMIC CHARACTERISTICS Symbol Parameter Conditions Typ. Max. Units Peak reverse and off-state current At VRRM/VDRM, Tcase = 125oC - 250 mA dV/dt Maximum linear rate of rise of off-state voltage To 67% VDRM Tj = 125oC. - 1000 V/µs - 150 A/µs Rate of rise of on-state current From 67% VDRM to 1000A Gate source 20V, 10Ω tr ≤ 0.5µs, Tj = 125oC Repetitive 50Hz dI/dt Non-repetitive - 300 A/µs IRRM/IDRM Threshold voltage At Tvj = 125oC - 1.03 V rT On-state slope resistance At Tvj = 125oC - 0.32 mΩ tgd Delay time VD = 67% VDRM, Gate source 30V, 15Ω tr = 0.5µs, Tj = 25oC - 2.5 µs tq Turn-off time VR = 50V, dIRR/dt = 2A/µs, VDR = 67% VDRM, dVDR/dt = 8V/µs linear 600 800 µs IL Latching current Tj = 25oC, VD = 5V 300 1000 mA IH Holding current Tj = 25oC, Rg-k = ∞ - 500 mA Max. Units VT(TO) IT = 1000A, tp = 1ms, Tj = 125˚C, GATE TRIGGER CHARACTERISTICS AND RATINGS Symbol Parameter Conditions VGT Gate trigger voltage VDRM = 5V, Tcase = 25oC 4.0 V IGT Gate trigger current VDRM = 5V, Tcase = 25oC 400 mA VGD Gate non-trigger voltage At VDRM Tcase = 125oC 0.25 V VFGM Peak forward gate voltage Anode positive with respect to cathode 30 V VFGN Peak forward gate voltage Anode negative with respect to cathode 0.25 V VRGM Peak reverse gate voltage 5 V IFGM Peak forward gate current Anode positive with respect to cathode 30 A PGM Peak gate power See table, gate characteristics curve 150 W PG(AV) Mean gate power 10 W 4/9 www.dynexsemi.com DCR1476SY / DCR1476SV CURVES 8000 7000 Measured under pulse conditions Tj = 125˚C d.c. Half wave 3 phase 6000 Instantaneous on-state current, IT - (A) 6 phase Mean power dissipation - (W) 6000 4000 5000 4000 3000 2000 2000 1000 0 1.0 2.0 3.0 Instantaneous on-state voltage, VT - (V) Fig.2 Maximum (limit) on-state characteristics 4.0 0 0 1000 2000 3000 Mean on-state current, IT(AV) - (A) 4000 Fig.3 Dissipation curves VTM Equation:VTM = A + Bln (IT) + C.IT+D.√IT Where A = 0.8659641 B = 0.03698496 C = 3.245389 x 10–4 D = –2.597435 x 10–3 these values are valid for Tj = 125˚C for IT 500A to 7000A 5/9 www.dynexsemi.com DCR1476SY / DCR1476SV 100 IT Table gives pulse power PGM in Watts VFGM tp dI/dt IT = 2000A 10000 Gate trigger voltage, VGT - (V) Total stored charge, QS - (µC) IRM Pulse width µs 100 200 500 1ms 10ms Pulse frequency Hz 50 100 400 150 150 150 150 150 125 150 150 100 150 100 25 20 - 10 Up 1 pe Low im rl er li it 9 mit 100W 50W 20W 10W 5W 2W 9% 1% Tj = 25˚C Tj = -40˚C QS Tj = 125˚C 100000 Conditions: Tj = 125˚C QS is total integral stored charge 1000 0.1 1.0 10 0.1 0.001 100 0.01 0.1 1 Gate trigger current, IGT - (A) Rate of decay of on-state current, dI/dt - (A/µs) Fig.4 Stored charge 10 Fig.5 Gate characteristics 0.1 60 0.01 Double side cooled 0.001 Conduction d.c. Halfwave 3 phase 120˚ 6 phase 60˚ 0.0001 0.001 0.01 Effective thermal resistance Junction to case ˚C/W Double side 0.0095 0.0105 0.0112 0.0139 0.1 1 Time - (s) 50 40 4.4 4.0 I2t value - (A2s x 106) Thermal impedance - (˚C/W) Anode side cooled Peak half sine wave on-state current - (kA) I2t = Î2 x t 2 30 3.6 3.2 I2t 2.8 20 2.4 Anode side 0.019 0.020 0.0207 0.0234 10 2.0 100 Fig.6 Transient thermal impedance - junction to case 10 1 10 ms 1 2 3 45 10 1.6 20 30 50 Cycles at 50Hz Duration Fig.7 Surge (non-repetitive) on-state current vs time (with 50% VRSM at Tcase = 125˚C) 6/9 www.dynexsemi.com DCR1476SY / DCR1476SV PACKAGE DETAILS For further package information, please contact Customer Services. All dimensions in mm, unless stated otherwise. DO NOT SCALE. Hole Ø3.6 x 2.0 deep (One in each electrode) Cathode tab Cathode Ø112.5 max Ø73 nom 37.7 36.0 Ø1.5 Gate Ø73 nom Anode Nominal weight: 1600g Clamping force: 43kN ±10% Package outline type code: Y Fig.8 Package details 7/9 www.dynexsemi.com DCR1476SY / DCR1476SV PACKAGE DETAILS For further package information, please contact Customer Services. All dimensions in mm, unless stated otherwise. DO NOT SCALE. 2 holes Ø3.6 x 2.0 deep (In both electrodes) Cathode tab Cathode Ø112.5 max Ø73 nom 27.0 25.4 Ø1.5 Gate Ø73 nom Anode Nominal weight: 1100g Clamping force: 43kN ±10% Lead length: 420mm Lead terminal connector: M4 ring Package outline type code: V Fig.9 Package details 8/9 www.dynexsemi.com POWER ASSEMBLY CAPABILITY The Power Assembly group was set up to provide a support service for those customers requiring more than the basic semiconductor, and has developed a flexible range of heatsink and clamping systems in line with advances in device voltages and current capability of our semiconductors. We offer an extensive range of air and liquid cooled assemblies covering the full range of circuit designs in general use today. The Assembly group offers high quality engineering support dedicated to designing new units to satisfy the growing needs of our customers. Using the latest CAD methods our team of design and applications engineers aim to provide the Power Assembly Complete Solution (PACs). HEATSINKS The Power Assembly group has its own proprietary range of extruded aluminium heatsinks which have been designed to optimise the performance of Dynex semiconductors. Data with respect to air natural, forced air and liquid cooling (with flow rates) is available on request. For further information on device clamps, heatsinks and assemblies, please contact your nearest sales representative or Customer Services. http://www.dynexsemi.com e-mail: [email protected] HEADQUARTERS OPERATIONS DYNEX SEMICONDUCTOR LTD Doddington Road, Lincoln. Lincolnshire. LN6 3LF. United Kingdom. Tel: +44-(0)1522-500500 Fax: +44-(0)1522-500550 CUSTOMER SERVICE Tel: +44 (0)1522 502753 / 502901. Fax: +44 (0)1522 500020 SALES OFFICES Benelux, Italy & Switzerland: Tel: +33 (0)1 64 66 42 17. Fax: +33 (0)1 64 66 42 19. France: Tel: +33 (0)2 47 55 75 53. Fax: +33 (0)2 47 55 75 59. Germany, Northern Europe, Spain & Rest Of World: Tel: +44 (0)1522 502753 / 502901. Fax: +44 (0)1522 500020 North America: Tel: (440) 259-2060. Fax: (440) 259-2059. Tel: (949) 733-3005. Fax: (949) 733-2986. These offices are supported by Representatives and Distributors in many countries world-wide. © Dynex Semiconductor 2003 TECHNICAL DOCUMENTATION – NOT FOR RESALE. PRODUCED IN UNITED KINGDOM This publication is issued to provide information only which (unless agreed by the Company in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. The Company reserves the right to alter without prior notice the specification, design or price of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to the Company's conditions of sale, which are available on request. All brand names and product names used in this publication are trademarks, registered trademarks or trade names of their respective owners. www.dynexsemi.com