CYPRESS CY7C1327G

CY7C1327G
PRELIMINARY
4-Mbit (256K x 18) Pipelined Sync SRAM
Functional Description[1]
Features
• Registered inputs and outputs for pipelined operation
• 256K ×18 common I/O architecture
• 3.3V core power supply
• 3.3V / 2.5V I/O operation
• Fast clock-to-output times
— 2.6 ns (for 250-MHz device)
— 2.6 ns (for 225-MHz device)
— 2.8 ns (for 200-MHz device)
The CY7C1327G SRAM integrates 262,144 x 18 SRAM cells
with advanced synchronous peripheral circuitry and a two-bit
counter for internal burst operation. All synchronous inputs are
gated by registers controlled by a positive-edge-triggered
Clock Input (CLK). The synchronous inputs include all
addresses, all data inputs, address-pipelining Chip Enable
(CE1), depth-expansion Chip Enables (CE2 and CE3), Burst
Control inputs (ADSC, ADSP, and ADV), Write Enables
(BW[A:B], and BWE), and Global Write (GW). Asynchronous
inputs include the Output Enable (OE) and the ZZ pin.
Addresses and chip enables are registered at rising edge of
clock when either Address Strobe Processor (ADSP) or
Address Strobe Controller (ADSC) are active. Subsequent
burst addresses can be internally generated as controlled by
the Advance pin (ADV).
— 3.5 ns (for 166-MHz device)
— 4.0 ns (for 133-MHz device)
— 4.5 ns (for 100-MHz device)
• Provide high-performance 3-1-1-1 access rate
• User-selectable burst counter supporting Intel®
Pentium® interleaved or linear burst sequences
• Separate processor and controller address strobes
• Synchronous self-timed writes
• Asynchronous output enable
• Lead-Free 100-pin TQFP and 119 Ball BGA packages.
• “ZZ” Sleep Mode Option
Address, data inputs, and write controls are registered on-chip
to initiate a self-timed Write cycle.This part supports Byte Write
operations (see Pin Descriptions and Truth Table for further
details). Write cycles can be one to two bytes wide as
controlled by the byte write control inputs. GW when active
LOW causes all bytes to be written.
The CY7C1327G operates from a +3.3V core power supply
while all outputs also operate with a +3.3V or a +2.5V supply.
All inputs and outputs are JEDEC-standard JESD8-5compatible.
Logic Block Diagram
A0, A1, A
ADDRESS
REGISTER
2
MODE
A[1:0]
BURST Q1
COUNTER AND
LOGIC
CLR
Q0
ADV
CLK
ADSC
ADSP
BWB
DQB,DQPB
WRITE DRIVER
DQB,DQPB
WRITE REGISTER
MEMORY
ARRAY
BWA
SENSE
AMPS
OUTPUT
REGISTERS
DQA,DQPA
WRITE DRIVER
DQA,DQPA
WRITE REGISTER
OUTPUT
BUFFERS
DQs
DQPA
DQPB
E
BWE
GW
CE1
CE2
CE3
ENABLE
REGISTER
INPUT
REGISTERS
PIPELINED
ENABLE
OE
ZZ
SLEEP
CONTROL
1
Note:
1. For best–practices recommendations, please refer to the Cypress application note System Design Guidelines on www.cypress.com
Cypress Semiconductor Corporation
Document #: 38-05519 Rev. *A
•
3901 North First Street
•
San Jose, CA 95134
•
408-943-2600
Revised October 21, 2004
PRELIMINARY
CY7C1327G
Selection Guide
250 MHz
225 MHz
200 MHz
166 MHz
133 MHz
100 MHz
Unit
Maximum Access Time
2.6
2.6
2.8
3.5
4.0
4.5
ns
Maximum Operating Current
325
290
265
240
225
205
mA
Maximum CMOS Standby
Current
40
40
40
40
40
40
mA
Shaded areas contain advance information. Please contact your local Cypress sales representative for availability of these parts.
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
A
A
CE1
CE2
NC
NC
BWB
BWA
CE3
VDD
VSS
CLK
GW
BWE
OE
ADSC
ADSP
ADV
A
A
Pin Configurations
NC
NC
NC
BYTE B
VDDQ
VSS
NC
NC
DQB
DQB
VSS
VDDQ
DQB
DQB
NC
VDD
100-pin TQFP
CY7C1327G
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
A
NC
NC
VDDQ
VSS
NC
DQPA
DQA
DQA
VSS
VDDQ
DQA
DQA
VSS
NC
VDD
ZZ
DQA
DQA
VDDQ
VSS
DQA
DQA
NC
NC
VSS
VDDQ
NC
NC
NC
BYTE A
MODE
A
A
A
A
A1
A0
NC
NC
VSS
VDD
NC
NC
A
A
A
A
A
A
A
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
NC
VSS
DQB
DQB
VDDQ
VSS
DQB
DQB
DQPB
NC
VSS
VDDQ
NC
NC
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Document #: 38-05519 Rev. *A
Page 2 of 18
PRELIMINARY
CY7C1327G
Pin Configurations
119-ball BGA
1
2
3
4
5
6
7
A
VDDQ
A
A
ADSP
A
A
VDDQ
B
C
NC
NC
CE2
A
A
A
ADSC
VDD
A
A
CE3
A
NC
NC
D
DQB
NC
VSS
NC
VSS
DQPA
NC
E
F
NC
VDDQ
DQB
NC
VSS
VSS
VSS
VSS
NC
DQA
DQA
VDDQ
G
H
J
NC
DQB
VDDQ
DQB
NC
VDD
BWB
VSS
NC
CE1
OE
ADV
GW
VDD
Vss
VSS
NC
NC
DQA
VDD
DQA
NC
VDDQ
K
NC
DQB
VSS
CLK
VSS
NC
DQA
L
DQB
NC
Vss
NC
BWA
DQA
NC
M
N
VDDQ
DQB
DQB
NC
VSS
VSS
BWE
A1
VSS
VSS
NC
DQA
VDDQ
NC
P
NC
DQPB
VSS
A0
VSS
NC
DQA
R
T
NC
NC
A
MODE
VDD
A
A
NC
NC
A
A
A
NC
ZZ
U
VDDQ
NC
NC
NC
NC
NC
VDDQ
Document #: 38-05519 Rev. *A
Page 3 of 18
PRELIMINARY
CY7C1327G
Pin Definitions
Name
A0, A1, A
BWA,BWB
I/O
Description
InputAddress Inputs used to select one of the 256K address locations. Sampled at the rising edge
Synchronous of the CLK if ADSP or ADSC is active LOW, and CE1, CE2, and CE3 are sampled active. A1, A0
feed the 2-bit counter.
InputByte Write Select Inputs, active LOW. Qualified with BWE to conduct byte writes to the SRAM.
Synchronous Sampled on the rising edge of CLK.
GW
InputGlobal Write Enable Input, active LOW. When asserted LOW on the rising edge of CLK, a global
Synchronous write is conducted (ALL bytes are written, regardless of the values on BW[A:B] and BWE).
BWE
InputByte Write Enable Input, active LOW. Sampled on the rising edge of CLK. This signal must be
Synchronous asserted LOW to conduct a byte write.
CLK
CE1
CE2
CE3
OE
ADV
ADSP
InputClock
Clock Input. Used to capture all synchronous inputs to the device. Also used to increment the
burst counter when ADV is asserted LOW, during a burst operation.
InputChip Enable 1 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with
Synchronous CE2 and CE3 to select/deselect the device. ADSP is ignored if CE1 is HIGH. CE1 is sampled only
when a new external address is loaded.
InputChip Enable 2 Input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction with
Synchronous CE1 and CE3 to select/deselect the device. CE2 is sampled only when a new external address is
loaded.
InputChip Enable 3 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with
Synchronous CE1 and CE2 to select/deselect the device. Not connected for BGA. Where referenced, CE3 is
assumed active throughout this document for BGA. CE3 is sampled only when a new external
address is loaded.
InputOutput Enable, asynchronous input, active LOW. Controls the direction of the I/O pins. When
Asynchronous LOW, the I/O pins behave as outputs. When deasserted HIGH, I/O pins are tri-stated, and act as
input data pins. OE is masked during the first clock of a read cycle when emerging from a
deselected state.
InputAdvance Input signal, sampled on the rising edge of CLK, active LOW. When asserted, it
Synchronous automatically increments the address in a burst cycle.
InputAddress Strobe from Processor, sampled on the rising edge of CLK, active LOW. When
Synchronous asserted LOW, A is captured in the address registers. A1, A0 are also loaded into the burst counter.
When ADSP and ADSC are both asserted, only ADSP is recognized. ASDP is ignored when CE1
is deasserted HIGH.
ZZ
InputZZ “sleep” Input, active HIGH. This input, when High places the device in a non-time-critical
Asynchronous “sleep” condition with data integrity preserved. For normal operation, this pin has to be LOW or
left floating. ZZ pin has an internal pull-down.
ADSC
InputAddress Strobe from Controller, sampled on the rising edge of CLK, active LOW. When
Synchronous asserted LOW, A is captured in the address registers. A1, A0 are also loaded into the burst counter.
When ADSP and ADSC are both asserted, only ADSP is recognized.
I/OBidirectional Data I/O lines. As inputs, they feed into an on-chip data register that is triggered
Synchronous by the rising edge of CLK. As outputs, they deliver the data contained in the memory location
specified by “A” during the previous clock rise of the read cycle. The direction of the pins is
controlled by OE. When OE is asserted LOW, the pins behave as outputs. When HIGH, DQs and
DQP[A:B] are placed in a tri-state condition.
DQA,
DQB
DQPA,
DQPB
VDD
VSS
Power Supply Power supply inputs to the core of the device.
Ground
VDDQ
I/O Ground
MODE
InputStatic
NC
Document #: 38-05519 Rev. *A
Ground for the device.
Ground for the I/O circuitry.
Selects Burst Order. When tied to GND selects linear burst sequence. When tied to VDD or left
floating selects interleaved burst sequence. This is a strap pin and should remain static during
device operation. Mode Pin has an internal pull-up.
No Connects. Not internally connected to the die.
Page 4 of 18
PRELIMINARY
Functional Overview
All synchronous inputs pass through input registers controlled
by the rising edge of the clock. All data outputs pass through
output registers controlled by the rising edge of the clock.
The CY7C1327G supports secondary cache in systems
utilizing either a linear or interleaved burst sequence. The
interleaved burst order supports Pentium and i486™
processors. The linear burst sequence is suited for processors
that utilize a linear burst sequence. The burst order is user
selectable, and is determined by sampling the MODE input.
Accesses can be initiated with either the Processor Address
Strobe (ADSP) or the Controller Address Strobe (ADSC).
Address advancement through the burst sequence is
controlled by the ADV input. A two-bit on-chip wraparound
burst counter captures the first address in a burst sequence
and automatically increments the address for the rest of the
burst access.
Byte Write operations are qualified with the Byte Write Enable
(BWE) and Byte Write Select (BW[A:B]) inputs. A Global Write
Enable (GW) overrides all Byte Write inputs and writes data to
all four bytes. All writes are simplified with on-chip
synchronous self-timed Write circuitry.
Three synchronous Chip Selects (CE1, CE2, CE3) and an
asynchronous Output Enable (OE) provide for easy bank
selection and output tri-state control. ADSP is ignored if CE1
is HIGH.
Single Read Accesses
This access is initiated when the following conditions are
satisfied at clock rise: (1) ADSP or ADSC is asserted LOW, (2)
CE1, CE2, CE3 are all asserted active, and (3) the Write
signals (GW, BWE) are all deserted HIGH. ADSP is ignored if
CE1 is HIGH. The address presented to the address inputs (A)
is stored into the address advancement logic and the Address
Register while being presented to the memory array. The
corresponding data is allowed to propagate to the input of the
Output Registers. At the rising edge of the next clock the data
is allowed to propagate through the output register and onto
the data bus within tco if OE is active LOW. The only exception
occurs when the SRAM is emerging from a deselected state
to a selected state, its outputs are always tri-stated during the
first cycle of the access. After the first cycle of the access, the
outputs are controlled by the OE signal. Consecutive single
Read cycles are supported. Once the SRAM is deselected at
clock rise by the chip select and either ADSP or ADSC signals,
its output will tri-state immediately.
Single Write Accesses Initiated by ADSP
This access is initiated when both of the following conditions
are satisfied at clock rise: (1) ADSP is asserted LOW, and
(2) CE1, CE2, CE3 are all asserted active. The address
presented to A is loaded into the address register and the
address advancement logic while being delivered to the
memory array. The Write signals (GW, BWE, and BW[A:B]) and
ADV inputs are ignored during this first cycle.
ADSP-triggered Write accesses require two clock cycles to
complete. If GW is asserted LOW on the second clock rise, the
data presented to the DQ inputs is written into the corresponding address location in the memory array. If GW is HIGH,
Document #: 38-05519 Rev. *A
CY7C1327G
then the Write operation is controlled by BWE and BW[A:B]
signals. The CY7C1327G provides Byte Write capability that
is described in the Write Cycle Descriptions table. Asserting
the Byte Write Enable input (BWE) with the selected Byte
Write (BW[A:B]) input, will selectively write to only the desired
bytes. Bytes not selected during a Byte Write operation will
remain unaltered. A synchronous self-timed Write mechanism
has been provided to simplify the Write operations.
Because the CY7C1327G is a common I/O device, the Output
Enable (OE) must be deserted HIGH before presenting data
to the DQ inputs. Doing so will tri-state the output drivers. As
a safety precaution, DQs are automatically tri-stated whenever
a Write cycle is detected, regardless of the state of OE.
Single Write Accesses Initiated by ADSC
ADSC Write accesses are initiated when the following conditions are satisfied: (1) ADSC is asserted LOW, (2) ADSP is
deserted HIGH, (3) CE1, CE2, CE3 are all asserted active, and
(4) the appropriate combination of the Write inputs (GW, BWE,
and BW[A:B]) are asserted active to conduct a Write to the
desired byte(s). ADSC-triggered Write accesses require a
single clock cycle to complete. The address presented to A is
loaded into the address register and the address
advancement logic while being delivered to the memory array.
The ADV input is ignored during this cycle. If a global Write is
conducted, the data presented to DQ is written into the corresponding address location in the memory core. If a Byte Write
is conducted, only the selected bytes are written. Bytes not
selected during a Byte Write operation will remain unaltered.
A synchronous self-timed Write mechanism has been
provided to simplify the Write operations.
Because the CY7C1327G is a common I/O device, the Output
Enable (OE) must be deserted HIGH before presenting data
to the DQ inputs. Doing so will tri-state the output drivers. As
a safety precaution, DQs are automatically tri-stated whenever
a Write cycle is detected, regardless of the state of OE.
Burst Sequences
The CY7C1327G provides a two-bit wraparound counter, fed
by A1, A0, that implements either an interleaved or linear burst
sequence. The interleaved burst sequence is designed specifically to support Intel Pentium applications. The linear burst
sequence is designed to support processors that follow a
linear burst sequence. The burst sequence is user selectable
through the MODE input.
Asserting ADV LOW at clock rise will automatically increment
the burst counter to the next address in the burst sequence.
Both Read and Write burst operations are supported.
Sleep Mode
The ZZ input pin is an asynchronous input. Asserting ZZ
places the SRAM in a power conservation “sleep” mode. Two
clock cycles are required to enter into or exit from this “sleep”
mode. While in this mode, data integrity is guaranteed.
Accesses pending when entering the “sleep” mode are not
considered valid nor is the completion of the operation
guaranteed. The device must be deselected prior to entering
the “sleep” mode. CE1, CE2, CE3, ADSP, and ADSC must
remain inactive for the duration of tZZREC after the ZZ input
returns LOW.
Page 5 of 18
PRELIMINARY
CY7C1327G
Interleaved Burst Address Table (MODE =
Floating or VDD)
First
Address
A1, A0
Second
Address
A1, A0
Third
Address
A1, A0
Fourth
Address
A1, A0
00
01
10
11
01
00
11
10
10
11
00
01
11
10
01
00
Linear Burst Address Table (MODE = GND)
First
Address
A1, A0
Second
Address
A1, A0
Third
Address
A1, A0
Fourth
Address
A1, A0
00
01
10
11
01
10
11
00
10
11
00
01
11
00
01
10
ZZ Mode Electrical Characteristics
Parameter
Description
Test Conditions
IDDZZ
Snooze mode standby current
ZZ > VDD – 0.2V
tZZS
Device operation to ZZ
ZZ > VDD – 0.2V
tZZREC
ZZ recovery time
ZZ < 0.2V
tZZI
ZZ active to snooze current
This parameter is sampled
tRZZI
ZZ Inactive to exit snooze current
This parameter is sampled
Document #: 38-05519 Rev. *A
Min.
Max.
Unit
40
mA
2tCYC
ns
2tCYC
ns
2tCYC
0
ns
ns
Page 6 of 18
PRELIMINARY
CY7C1327G
Truth Table[ 2, 3, 4, 5, 6]
Next Cycle
Add. Used
CE2
ZZ
X
CE3
X
DQ
L
ADSP
X
ADSC
L
ADV
X
OE
X
tri-state
WRITE
X
Unselected
None
CE1
H
Unselected
None
L
X
H
L
L
X
X
X
tri-state
X
Unselected
None
L
L
X
L
L
X
X
X
tri-state
X
Unselected
None
L
X
H
L
H
L
X
X
tri-state
X
Unselected
None
L
L
X
L
H
L
X
X
tri-state
X
Begin Read
External
L
H
L
L
L
X
X
X
tri-state
X
Begin Read
External
L
H
L
L
H
L
X
X
tri-state
H
X
X
X
L
H
H
L
H
tri-state
H
Continue Read Next
X
X
X
L
H
H
L
L
DQ
H
Continue Read Next
H
X
X
L
X
H
L
H
tri-state
H
Continue Read Next
H
X
X
L
X
H
L
L
DQ
H
Suspend Read Current
X
X
X
L
H
H
H
H
tri-state
H
Suspend Read Current
X
X
X
L
H
H
H
L
DQ
H
Suspend Read Current
H
X
X
L
X
H
H
H
tri-state
H
Suspend Read Current
H
X
X
L
X
H
H
L
DQ
H
Begin Write
Current
X
X
X
L
H
H
H
X
tri-state
L
Begin Write
Current
H
X
X
L
X
H
H
X
tri-state
L
Begin Write
External
L
H
L
L
H
H
X
X
tri-state
L
Continue Write Next
X
X
X
L
H
H
H
X
tri-state
L
Continue Write Next
H
X
X
L
X
H
H
X
tri-state
L
Continue Read Next
Suspend Write Current
X
X
X
L
H
H
H
X
tri-state
L
Suspend Write Current
H
X
X
L
X
H
H
X
tri-state
L
ZZ “Sleep”
X
X
X
H
X
X
X
X
tri-state
X
None
Truth Table for Read/Write[2]
Function
Read
GW
H
BWE
H
BWB
X
BWA
X
Read
H
L
H
H
Write Byte A – (DQA and DQPA)
Write Byte B – (DQB and DQPB)
H
L
H
L
H
L
L
H
Write Bytes B, A
H
L
L
L
Write All Bytes
H
L
L
L
Write All Bytes
L
X
X
X
Notes:
2. X = “Don't Care.” H = Logic HIGH, L = Logic LOW.
3. WRITE = L when any one or more Byte Write enable signals (BWA, BWB) and BWE = L or GW = L. WRITE = H when all Byte write enable signals (BWA, BWB),
BWE, GW = H.
4. The DQ pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock.
5. The SRAM always initiates a read cycle when ADSP is asserted, regardless of the state of GW, BWE, or BW[A: B]. Writes may occur only on subsequent clocks
after the ADSP or with the assertion of ADSC. As a result, OE must be driven HIGH prior to the start of the write cycle to allow the outputs to tri-state. OE is a
don't care for the remainder of the write cycle.
6. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle all data bits are tri-state when OE is
inactive or when the device is deselected, and all data bits behave as output when OE is active (LOW).
Document #: 38-05519 Rev. *A
Page 7 of 18
PRELIMINARY
Maximum Ratings
CY7C1327G
Current into Outputs (LOW)......................................... 20 mA
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ................................. –65°C to +150°C
Ambient Temperature with
Power Applied............................................. –55°C to +125°C
Supply Voltage on VDD Relative to GND........ –0.5V to +4.6V
DC Voltage Applied to Outputs
in tri-state ............................................ –0.5V to VDDQ + 0.5V
Static Discharge Voltage.......................................... > 2001V
(per MIL-STD-883, Method 3015)
Latch-up Current.................................................... > 200 mA
Operating Range
Ambient
Range
Temperature
VDD
VDDQ
Commercial 0°C to +70°C 3.3V –5%/+10% 2.5V –5%
to VDD
Industrial
–40°C to +85°C
DC Input Voltage....................................–0.5V to VDD + 0.5V
Electrical Characteristics Over the Operating Range [7, 8]
Parameter
Description
Test Conditions
Min.
Max.
Unit
VDD
Power Supply Voltage
3.135
3.6
V
VDDQ
I/O Supply Voltage
2.375
VDD
V
VOH
Output HIGH Voltage
VOL
VIH
VIL
IX
Output LOW Voltage
Input HIGH
Input LOW
Voltage[7]
Voltage[7]
Input Load Current
except ZZ and MODE
VDDQ = 3.3V, VDD = Min., IOH = –4.0 mA
2.4
V
VDDQ = 2.5V, VDD = Min., IOH = –1.0 mA
2.0
V
VDDQ = 3.3V, VDD = Min., IOL = 8.0 mA
0.4
V
VDDQ = 2.5V, VDD = Min., IOL = 1.0 mA
0.4
V
VDDQ = 3.3V
2.0
VDD + 0.3V
V
VDDQ = 2.5V
1.7
VDD + 0.3V
V
VDDQ = 3.3V
–0.3
0.8
V
VDDQ = 2.5V
–0.3
0.7
V
–5
5
µA
5
µA
GND ≤ VI ≤ VDDQ
Input = VDD
Input Current of ZZ
Input = VSS
30
IOZ
Output Leakage Current GND ≤ VI ≤ VDDQ, Output Disabled
IDD
VDD Operating Supply
Current
ISB1
ISB2
Automatic CE
Power-down
Current—TTL Inputs
VDD = Max, Device
Deselected, VIN ≥ VIH or
VIN ≤ VIL
f = fMAX = 1/tCYC
Automatic CE
VDD = Max, Device
Power-down
Deselected, VIN ≤ 0.3V or
Current—CMOS Inputs VIN > VDDQ – 0.3V, f = 0
µA
–5
Input = VDD
VDD = Max.,
IOUT = 0 mA,
f = fMAX =
1/tCYC
µA
–30
Input Current of MODE Input = VSS
µA
5
µA
4-ns cycle,250MHz
325
mA
4.4-ns cycle,225MHz
290
mA
5-ns cycle,200MHz
265
mA
–5
6-ns cycle,166MHz
240
mA
7.5-ns cycle,133MHz
225
mA
10-ns cycle,100MHz
205
mA
4-ns cycle,250MHz
120
mA
4.4-ns cycle,225MHz
115
mA
5-ns cycle,200MHz
110
mA
6-ns cycle,166MHz
100
mA
7.5-ns cycle,133MHz
90
mA
10-ns cycle,100MHz
80
mA
All speeds
40
mA
Shaded areas contain advance information.
Notes:
7. Overshoot: VIH(AC) < VDD +1.5V (Pulse width less than tCYC/2), undershoot: VIL(AC) > -2V (Pulse width less than tCYC/2).
8. TPower-up: Assumes a linear ramp from 0v to VDD(min.) within 200ms. During this time VIH < VDD and VDDQ < VDD.
Document #: 38-05519 Rev. *A
Page 8 of 18
PRELIMINARY
CY7C1327G
Electrical Characteristics Over the Operating Range (continued)[7, 8]
Parameter
ISB3
ISB4
Description
Test Conditions
Automatic CE
VDD = Max, Device
Power-down
Deselected, or VIN ≤ 0.3V
Current—CMOS Inputs or VIN > VDDQ – 0.3V
f = fMAX = 1/tCYC
Automatic CE
Power-down
Current—TTL Inputs
Max.
Unit
4-ns cycle,250MHz
105
mA
4.4-ns cycle,225MHz
100
mA
5-ns cycle,200MHz
95
mA
6-ns cycle,166MHz
85
mA
7.5-ns cycle,133MHz
75
mA
10-ns cycle,100MHz
65
mA
All speeds
45
mA
VDD = Max, Device
Deselected, VIN ≥ VIH or
VIN ≤ VIL, f = 0
Min.
Thermal Resistance[9]
Parameter
ΘJA
ΘJC
Description
Thermal Resistance
(Junction to Ambient)
Thermal Resistance
(Junction to Case)
Test Conditions
TQFP Package
BGA Package
Unit
Test conditions follow standard test
methods and procedures for measuring
thermal impedance, per EIA / JESD51.
TBD
TBD
°C/W
TBD
TBD
°C/W
Capacitance[9]
Parameter
Description
Test Conditions
CIN
Input Capacitance
CCLK
Clock Input Capacitance
CI/O
Input/Output Capacitance
TQFP Package
BGA Package Unit
5
TA = 25°C, f = 1 MHz,
VDD = 3.3V.
VDDQ = 3.3V
5
pF
5
5
pF
5
7
pF
AC Test Loads and Waveforms
3.3V I/O Test Load
R = 317Ω
3.3V
OUTPUT
ALL INPUT PULSES
VDDQ
OUTPUT
RL = 50Ω
Z0 = 50Ω
10%
90%
10%
90%
GND
5 pF
R = 351Ω
≤ 1ns
≤ 1ns
VT = 1.5V
INCLUDING
JIG AND
SCOPE
(a)
(c)
(b)
2.5V I/O Test Load
R = 1667Ω
2.5V
OUTPUT
Z0 = 50Ω
10%
R =1538Ω
VT = 1.25V
INCLUDING
JIG AND
SCOPE
90%
10%
90%
GND
5 pF
(a)
ALL INPUT PULSES
VDDQ
OUTPUT
RL = 50Ω
(b)
≤ 1ns
≤ 1ns
(c)
Notes:
9. Tested initially and after any design or process change that may affect these parameters.
Document #: 38-05519 Rev. *A
Page 9 of 18
PRELIMINARY
CY7C1327G
Switching Characteristics Over the Operating Range[14, 15]
250 MHz
Parameter
tPOWER
tDOH
Data Output Hold After CLK
Rise
tCLZ
Clock to Low-Z[11, 12, 13]
tCHZ
Clock to High-Z[11, 12, 13]
tOEV
OE LOW to Output Valid
OE LOW to Output Low-Z[11,
tOEHZ
200 MHz
166 MHz
133 MHz
100 MHz
Min. Max Min. Max Min. Max Min. Max Min. Max Min. Max Unit
Description
VDD(Typical) to the first[10]
Clock
tCYC
Clock Cycle Time
Clock HIGH
tCH
Clock LOW
tCL
Output Times
Data Output Valid After CLK
tCO
Rise
tOELZ
225 MHz
1
1
1
1
1
1
ms
4.0
1.7
1.7
4.4
2.0
2.0
5.0
2.0
2.0
6.0
2.5
2.5
7.5
3.0
3.0
10
3.5
3.5
ns
ns
ns
2.6
1.0
2.6
1.0
0
12, 13]
[11,
2.6
OE HIGH to Output High-Z
2.6
2.8
4.5
0
3.5
ns
4.5
ns
4.5
ns
0
4.0
ns
ns
0
4.0
3.5
0
4.5
1.5
0
3.5
2.8
0
4.0
1.5
0
2.8
2.6
0
3.5
1.5
0
2.6
2.6
0
12, 13]
1.0
0
2.6
2.8
ns
4.5
ns
Set-up Times
tAS
Address Set-up Before CLK
Rise
1.2
1.2
1.2
1.5
1.5
1.5
ns
tADS
1.2
ADSC, ADSP Set-up Before
CLK Rise
ADV Set-up Before CLK Rise 1.2
GW, BWE, BWX Set-up Before 1.2
CLK Rise
1.2
1.2
1.5
1.5
1.5
ns
1.2
1.2
1.5
1.5
1.5
ns
1.2
1.2
1.5
1.5
1.5
ns
tDS
Data Input Set-up Before CLK
Rise
1.2
1.2
1.2
1.5
1.5
1.5
ns
tCES
Chip Enable Set-Up Before
CLK Rise
1.2
1.2
1.2
1.5
1.5
1.5
ns
tADVS
tWES
Hold Times
Address Hold After CLK Rise
0.3
0.5
0.5
0.5
0.5
0.5
ns
tADH
ADSP , ADSC Hold After CLK
Rise
0.3
0.5
0.5
0.5
0.5
0.5
ns
tADVH
ADV Hold After CLK Rise
GW,BWE, BWX Hold After
CLK Rise
Data Input Hold After CLK
Rise
0.3
0.5
0.5
0.5
0.5
0.5
ns
0.3
0.5
0.5
0.5
0.5
0.5
ns
0.3
0.5
0.5
0.5
0.5
0.5
ns
Chip Enable Hold After CLK
Rise
0.3
0.5
0.5
0.5
0.5
0.5
ns
tAH
tWEH
tDH
tCEH
Shaded areas contain advance information.
Notes:
10. This part has a voltage regulator internally; tPOWER is the time that the power needs to be supplied above VDD(minimum) initially before a read or write operation
can be initiated.
11. tCHZ, tCLZ,tOELZ, and tOEHZ are specified with AC test conditions shown in part (b) of AC Test Loads. Transition is measured ± 200 mV from steady-state voltage.
12. At any given voltage and temperature, tOEHZ is less than tOELZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same
data bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed
to achieve High-Z prior to Low-Z under the same system conditions.
13. This parameter is sampled and not 100% tested.
14. Timing references level is 1.5V when VDDQ = 3.3V and is 1.25V when VDDQ = 2.5V on all data sheets.
15. Test conditions shown in (a) of AC Test Loads unless otherwise noted.
Document #: 38-05519 Rev. *A
Page 10 of 18
PRELIMINARY
CY7C1327G
Switching Waveforms
Read Cycle Timing[16]
t CYC
CLK
t
CH
t
ADS
t
CL
t
ADH
ADSP
tADS
tADH
ADSC
tAS
ADDRESS
tAH
A1
A2
tWES
A3
Burst continued with
new base address
tWEH
GW, BWE,
BW[A:B]
Deselect
cycle
tCES tCEH
CE
tADVS tADVH
ADV
ADV
suspends
burst.
OE
t OEHZ
t CLZ
Data Out (Q)
High-Z
Q(A1)
tOEV
tCO
t OELZ
tDOH
Q(A2)
t CHZ
Q(A2 + 1)
Q(A2 + 2)
Q(A2 + 3)
Q(A2)
Q(A2 + 1)
t CO
Single READ
BURST READ
DON’T CARE
Burst wraps around
to its initial state
UNDEFINED
Notes:
16. On this diagram, when CE is LOW: CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH: CE1 is HIGH or CE2 is LOW or CE3 is HIGH.
17. Full width write can be initiated by either GW LOW; or by GW HIGH, BWE LOW and BW[A:B] LOW.
Document #: 38-05519 Rev. *A
Page 11 of 18
PRELIMINARY
CY7C1327G
Switching Waveforms (continued)
Write Cycle Timing[16, 17]
t CYC
CLK
tCH
tADS
tCL
tADH
ADSP
tADS
ADSC extends burst
tADH
tADS
tADH
ADSC
tAS
tAH
A1
ADDRESS
A2
A3
Byte write signals are
ignored for first cycle when
ADSP initiates burst
tWES tWEH
BWE,
BW[A :B]
tWES tWEH
GW
tCES
tCEH
CE
t
t
ADVS ADVH
ADV
ADV suspends burst
OE
tDS
Data In (D)
High-Z
t
OEHZ
tDH
D(A1)
D(A2)
D(A2 + 1)
D(A2 + 1)
D(A2 + 2)
D(A2 + 3)
D(A3)
D(A3 + 1)
D(A3 + 2)
Data Out (Q)
BURST READ
Single WRITE
BURST WRITE
DON’T CARE
Document #: 38-05519 Rev. *A
Extended BURST WRITE
UNDEFINED
Page 12 of 18
PRELIMINARY
CY7C1327G
Switching Waveforms (continued)
Read/Write Cycle Timing[16, 18, 19]
tCYC
CLK
tCL
tCH
tADS
tADH
tAS
tAH
ADSP
ADSC
ADDRESS
A1
A2
A3
A4
A5
A6
D(A5)
D(A6)
tWES tWEH
BWE,
BW[A:B]
tCES
tCEH
CE
ADV
OE
tDS
tCO
Data In (D)
tOELZ
High-Z
tCLZ
Data Out (Q)
tDH
High-Z
Q(A1)
Back-to-Back READs
tOEHZ
D(A3)
Q(A2)
Q(A4)
Single WRITE
Q(A4+1)
Q(A4+2)
BURST READ
DON’T CARE
Q(A4+3)
Back-to-Back
WRITEs
UNDEFINED
Notes:
18. The data bus (Q) remains in high-Z following a WRITE cycle, unless a new read access is initiated by ADSP or ADSC.
19. GW is HIGH.
Document #: 38-05519 Rev. *A
Page 13 of 18
PRELIMINARY
CY7C1327G
Switching Waveforms (continued)
ZZ Mode Timing [20, 21]
CLK
t
ZZ
I
t
t
ZZ
ZZREC
ZZI
SUPPLY
I
DDZZ
t RZZI
ALL INPUTS
(except ZZ)
DESELECT or READ Only
Outputs (Q)
High-Z
DON’T CARE
Ordering Information
Speed
(MHz)
250
225
200
Package
Name
Package Type
Operating
Range
CY7C1327G-250AXC
A101
Lead-Free 100-Lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
Commercial
CY7C1327G-250BGC
BG119
119-Ball BGA (14 x 22 x 2.4mm)
CY7C1327G-250BGXC
BG119
Lead-Free 119-Ball BGA (14 x 22 x 2.4mm)
Ordering Code
CY7C1327G-250AXI
A101
Lead-Free 100-Lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
CY7C1327G-250BGI
BG119
119-Ball BGA (14 x 22 x 2.4mm)
CY7C1327G-250BGXI
BG119
Lead-Free 119-Ball BGA (14 x 22 x 2.4mm)
CY7C1327G-225AXC
A101
CY7C1327G-225BGC
BG119
Lead-Free 100-Lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
119-Ball BGA (14 x 22 x 2.4mm)
CY7C1327G-225BGXC
BG119
Lead-Free 119-Ball BGA (14 x 22 x 2.4mm)
CY7C1327G-225AXI
A101
Lead-Free 100-Lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
CY7C1327G-225BGI
BG119
119-Ball BGA (14 x 22 x 2.4mm)
CY7C1327G-225BGXI
BG119
Lead-Free 119-Ball BGA (14 x 22 x 2.4mm)
CY7C1327G-200AXC
A101
CY7C1327G-200BGC
BG119
Lead-Free 100-Lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
119-Ball BGA (14 x 22 x 2.4mm)
CY7C1327G-200BGXC
BG119
Lead-Free 119-Ball BGA (14 x 22 x 2.4mm)
CY7C1327G-200AXI
A101
Lead-Free 100-Lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
CY7C1327G-200BGI
BG119
119-Ball BGA (14 x 22 x 2.4mm)
CY7C1327G-200BGXI
BG119
Lead-Free 119-Ball BGA (14 x 22 x 2.4mm)
Industrial
Commercial
Industrial
Commercial
Industrial
Notes:
20. Device must be deselected when entering ZZ mode. See Cycle Descriptions table for all possible signal conditions to deselect the device.
21. DQs are in high-Z when exiting ZZ sleep mode.
Document #: 38-05519 Rev. *A
Page 14 of 18
PRELIMINARY
CY7C1327G
Ordering Information (continued)
Speed
(MHz)
166
133
100
Package
Name
Package Type
Operating
Range
CY7C1327G-166AXC
A101
Lead-Free 100-Lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
Commercial
CY7C1327G-166BGC
BG119
119-Ball BGA (14 x 22 x 2.4mm)
CY7C1327G-166BGXC
BG119
Lead-Free 119-Ball BGA (14 x 22 x 2.4mm)
Ordering Code
CY7C1327G-166AXI
A101
Lead-Free 100-Lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
CY7C1327G-166BGI
BG119
119-Ball BGA (14 x 22 x 2.4mm)
CY7C1327G-166BGXI
BG119
Lead-Free 119-Ball BGA (14 x 22 x 2.4mm)
CY7C1327G-133AXC
A101
CY7C1327G-133BGC
BG119
Lead-Free 100-Lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
119-Ball BGA (14 x 22 x 2.4mm)
CY7C1327G-133BGXC
BG119
Lead-Free 119-Ball BGA (14 x 22 x 2.4mm)
CY7C1327G-133AXI
A101
Lead-Free 100-Lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
CY7C1327G-133BGI
BG119
119-Ball BGA (14 x 22 x 2.4mm)
CY7C1327G-133BGXI
BG119
Lead-Free 119-Ball BGA (14 x 22 x 2.4mm)
CY7C1327G-100AXC
A101
CY7C1327G-100BGC
BG119
Lead-Free 100-Lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
119-Ball BGA (14 x 22 x 2.4mm)
CY7C1327G-100BGXC
BG119
Lead-Free 119-Ball BGA (14 x 22 x 2.4mm)
CY7C1327G-100AXI
A101
Lead-Free 100-Lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
CY7C1327G-100BGI
BG119
119-Ball BGA (14 x 22 x 2.4mm)
CY7C1327G-100BGXI
BG119
Lead-Free 119-Ball BGA (14 x 22 x 2.4mm)
Industrial
Commercial
Industrial
Commercial
Industrial
Shaded areas contain advance information. Please contact your local Cypress sales representative for availability of these parts. Lead-Free BG package will be
available in 2005
Document #: 38-05519 Rev. *A
Page 15 of 18
PRELIMINARY
CY7C1327G
Package Diagrams
100-Pin Thin Plastic Quad Flatpack (14 x 20 x 1.4 mm) A101
51-85050-*A
Document #: 38-05519 Rev. *A
Page 16 of 18
PRELIMINARY
CY7C1327G
Package Diagrams (continued)
119-Lead BGA (14 x 22 x 2.4 mm) BG119
51-85115-*B
i486 is a trademark, and Intel and Pentium are registered trademarks, of Intel Corporation. PowerPC is a registered trademark
of IBM Corporation. All product and company names mentioned in this document may be trademarks of their respective holders.
Document #: 38-05519 Rev. *A
Page 17 of 18
© Cypress Semiconductor Corporation, 2004. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
PRELIMINARY
CY7C1327G
Document History Page
Document Title: CY7C1327G 4-Mbit (256K x 18) Pipelined Sync SRAM
Document Number: 38-05519
REV.
ECN NO.
Issue Date
Orig. of
Change
Description of Change
**
224367
See ECN
RKF
New Data Sheet
*A
278513
See ECN
VBL
In Ordering Info section, Changed TQFP to PB-Free TQFP
Added PB-Free BG package.
Document #: 38-05519 Rev. *A
Page 18 of 18