CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 36-Mbit QDR-II™ SRAM 2-Word Burst Architecture Features Functional Description • Separate Independent Read and Write data ports The CY7C1410AV18, CY7C1425AV18, CY7C1412AV18, and CY7C1414AV18 are 1.8V Synchronous Pipelined SRAMs, equipped with QDR™-II architecture. QDR-II architecture consists of two separate ports to access the memory array. The Read port has dedicated Data Outputs to support Read operations and the Write Port has dedicated Data Inputs to support Write operations. QDR-II architecture has separate data inputs and data outputs to completely eliminate the need to “turn-around” the data bus required with common IO devices. Access to each port is accomplished through a common address bus. The Read address is latched on the rising edge of the K clock and the Write address is latched on the rising edge of the K clock. Accesses to the QDR-II Read and Write ports are completely independent of one another. In order to maximize data throughput, both Read and Write ports are equipped with Double Data Rate (DDR) interfaces. Each address location is associated with two 8-bit words (CY7C1410AV18) or 9-bit words (CY7C1425AV18) or 18-bit words (CY7C1412AV18) or 36-bit words (CY7C1414AV18) that burst sequentially into or out of the device. While data can be transferred into and out of the device on every rising edge of both input clocks (K and K and C and C), memory bandwidth is maximized while simplifying system design by eliminating bus “turn-arounds.” — Supports concurrent transactions • 250-MHz clock for high bandwidth • 2-Word Burst on all accesses • Double Data Rate (DDR) interfaces on both Read and Write ports (data transferred at 500 MHz) @ 250 MHz • Two input clocks (K and K) for precise DDR timing — SRAM uses rising edges only • Two input clocks for output data (C and C) to minimize clock skew and flight-time mismatches • Echo clocks (CQ and CQ) simplify data capture in high-speed systems • Single multiplexed address input bus latches address inputs for both Read and Write ports • Separate Port Selects for depth expansion • Synchronous internally self timed writes • Available in x8, x9, x18, and x36 configurations • Full data coherency, providing most current data • Core VDD = 1.8V (±0.1V); IO VDDQ = 1.4V to VDD Depth expansion is accomplished with Port Selects for each port. Port selects allow each port to operate independently. • Available in 165-Ball FBGA package (15 x 17 x 1.4 mm) • Offered in both Pb-free and non Pb-free packages All synchronous inputs pass through input registers controlled by the K or K input clocks. All data outputs pass through output registers controlled by the C or C (or K or K in a single clock domain) input clocks. Writes are conducted with on-chip synchronous self timed write circuitry. • Variable drive HSTL output buffers • JTAG 1149.1 compatible test access port • Delay Lock Loop (DLL) for accurate data placement Configurations CY7C1410AV18 – 4M x 8 CY7C1425AV18 – 4M x 9 CY7C1412AV18 – 2M x 18 CY7C1414AV18 – 1M x 36 Selection Guide 250 MHz 200 MHz 167 MHz Unit Maximum Operating Frequency 250 200 167 MHz Maximum Operating Current 1065 870 740 mA Cypress Semiconductor Corporation Document #: 38-05615 Rev. *D • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised July 09, 2007 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 Logic Block Diagram (CY7C1410AV18) D[7:0] CLK Gen. DOFF Address Register Read Add. Decode K K Write Add. Decode 21 Write Reg 2M x 8 Array Address Register Write Reg 2M x 8 Array A(20:0) 8 RPS Control Logic C C Read Data Reg. 16 VREF WPS NWS[1:0] CQ CQ 8 Reg. Control Logic A(20:0) 21 8 Reg. 8 8 Reg. Q[7:0] 8 Logic Block Diagram (CY7C1425AV18) K K CLK Gen. DOFF VREF WPS BWS[0] Address Register Read Add. Decode 21 Write Reg 2M x 9 Array Address Register Write Reg 2M x 9 Array A(20:0) 9 Write Add. Decode D[8:0] 21 A(20:0) RPS Control Logic C C Read Data Reg. CQ CQ 18 Control Logic 9 Reg. 9 Reg. 9 Document #: 38-05615 Rev. *D Reg. 9 9 Q [8:0] Page 2 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 Logic Block Diagram (CY7C1412AV18) D[17:0] K K CLK Gen. DOFF Address Register Read Add. Decode 20 Write Reg 1M x 18 Array A(19:0) Write Reg 1M x 18 Array Address Register Write Add. Decode 18 RPS Control Logic C C Read Data Reg. 36 VREF WPS BWS[1:0] CQ CQ 18 Reg. Control Logic A(19:0) 20 18 Reg. 18 18 Reg. Q[17:0] 18 Logic Block Diagram (CY7C1414AV18) K K CLK Gen. DOFF VREF WPS BWS[3:0] Address Register Read Add. Decode 19 Write Reg 512K x 36 Array Address Register Write Reg 512K x 36 Array A(18:0) 36 Write Add. Decode D[35:0] 19 RPS Control Logic C C Read Data Reg. 72 Control Logic Reg. Reg. 36 Reg. 36 36 Document #: 38-05615 Rev. *D CQ CQ 36 36 A(18:0) Q[35:0] Page 3 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 Pin Configurations 165-Ball FBGA (15 x 17 x 1.4 mm) Pinout CY7C1410AV18 (4M x 8) A B C D E F G H J K L M N P R 1 2 CQ NC/72M 3 4 5 NC A NC WPS A NWS1 NC/288M NC NC NC NC D4 NC NC VSS VSS A NC NC Q4 VDDQ VSS VSS NC NC NC NC VDDQ VDD VSS DOFF NC D5 VREF NC Q5 VDDQ NC VDDQ VDDQ VDDQ VDD VDD VDD VSS VSS VSS VSS 7 8 9 10 11 NC/144M NWS0 A VSS RPS A A NC A NC CQ Q3 VSS VSS NC NC NC D3 NC VSS VDDQ NC D2 Q2 VDD VDDQ NC NC NC VDD VDD VDD VDDQ VDDQ VDDQ NC VDDQ NC NC VREF Q1 NC ZQ D1 6 K K A VSS NC NC NC NC VDDQ VDD VSS VDD VDDQ NC NC NC NC Q6 D6 VDDQ VSS VSS VSS VDDQ NC NC Q0 NC NC NC D7 NC NC VSS VSS VSS A VSS A VSS A VSS VSS NC NC NC NC D0 NC NC NC Q7 A A C A A NC NC NC TDO TCK A A A C A A A TMS TDI CY7C1425AV18 (4M x 9) A B C D E F G H J K L M N P R 1 2 3 4 5 6 7 8 9 10 11 CQ NC/72M WPS NC K NC/144M RPS A A NC A NC CQ Q4 VSS VSS NC NC NC NC D4 NC NC NC A NC A NC/288M K NC NC NC D5 NC NC VSS VSS A VSS A VSS BWS0 A VSS NC NC Q5 VDDQ VSS VSS VSS VDDQ NC D3 Q3 NC NC NC NC VDDQ VDD VSS DOFF NC VDDQ VDDQ VDDQ VDD VDD VDD VSS VSS VSS VDDQ VDDQ VDDQ NC NC VDDQ NC NC Q6 VDDQ NC VDD VDD VDD VDD VDDQ D6 VREF NC NC VREF Q2 NC NC ZQ D2 NC NC NC VDDQ VDD VSS VDD VDDQ NC NC NC NC Q7 D7 VDDQ VSS VSS VSS VDDQ NC NC Q1 NC NC NC D8 NC NC VSS VSS VSS A VSS A VSS A VSS VSS NC NC NC NC D1 NC NC NC Q8 A A C A A NC D0 Q0 TDO TCK A A A C A A A TMS TDI Document #: 38-05615 Rev. *D Page 4 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 Pin Configurations (continued) 165-Ball FBGA (15 x 17 x 1.4 mm) Pinout CY7C1412AV18 (2M x 18) A B C D E F G H J K L M N P R 1 2 3 4 5 6 7 8 9 10 11 CQ NC NC/144M A WPS BWS1 K NC/288M A NC K BWS0 A NC CQ D9 RPS A NC/72M Q9 NC Q8 NC NC NC D11 D10 Q10 VSS VSS A A VSS VSS VSS NC VSS A VSS NC Q7 NC D8 D7 NC NC Q11 VDDQ VSS VSS VSS VDDQ NC D6 Q6 NC NC Q12 D12 VDDQ VDD VSS VDD VDDQ Q13 VDDQ D14 VDDQ VDDQ VDDQ VDD VDD VDD VSS VSS VSS VDD VDD VDD VDDQ VDDQ VDDQ NC NC VDDQ NC NC D13 VREF NC NC VREF Q4 Q5 D5 ZQ D4 NC NC Q14 VDDQ VDD VSS VDD VDDQ NC D3 Q3 NC Q15 D15 VDDQ VSS VSS VSS VDDQ NC NC Q2 NC NC NC D17 D16 Q16 VSS VSS VSS A VSS A VSS A VSS VSS NC NC Q1 NC D2 D1 NC NC Q17 A A C A A NC D0 Q0 TDO TCK A A A C A A A TMS TDI 7 8 9 10 11 DOFF NC CY7C1414AV18 (1M x 36) 1 A B C D E F G H J K L M N P R 2 3 5 6 WPS BWS2 K BWS1 D18 A A D17 Q17 CQ Q8 Q28 D20 D19 Q19 VSS VSS K A VSS BWS0 D27 D28 BWS3 A VSS RPS A NC/144M Q18 A VSS VSS VSS D16 Q16 Q7 D15 D8 D7 Q29 D29 Q20 VDDQ VSS VSS VSS VDDQ Q15 D6 Q6 Q30 Q21 D21 VDDQ VDD VSS DOFF D31 Q22 VDDQ D23 VDDQ VDDQ VDDQ VDD VDD VDD VSS VSS VSS VDDQ VDDQ VDDQ D14 Q13 VDDQ D12 Q14 D22 VREF Q31 VDD VDD VDD VDD VDDQ D30 D13 VREF Q4 Q5 D5 ZQ D4 Q32 D32 Q23 VDDQ VDD VSS VDD VDDQ Q12 D3 Q3 Q33 Q24 D24 VDDQ VSS VSS VSS VDDQ D11 Q11 Q2 D33 D34 Q34 D26 D25 Q25 VSS VSS VSS A VSS A VSS A VSS VSS D10 Q10 Q1 D9 D2 D1 Q35 D35 Q26 A A C A A Q9 D0 Q0 TDO TCK A A A C A A A TMS TDI CQ Q27 NC/288M NC/72M 4 Document #: 38-05615 Rev. *D Page 5 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 Pin Definitions IO Pin Description D[x:0] Pin Name InputSynchronous Data input signals, sampled on the rising edge of K and K clocks during valid write operations. CY7C1410AV18 - D[7:0] CY7C1425AV18 - D[8:0] CY7C1412AV18 - D[17:0] CY7C1414AV18 - D[35:0] WPS InputSynchronous Write Port Select, Active LOW. Sampled on the rising edge of the K clock. When asserted active, a Write operation is initiated. Deasserting deselects the Write port. Deselecting the Write port causes D[x:0] to be ignored. Nibble Write Select 0, 1 − Active LOW. (CY7C1410AV18 Only) Sampled on the rising edge of the K and K clocks during Write operations. Used to select which nibble is written into the device during the current portion of the Write operations.Nibbles not written remain unaltered. NWS0 controls D[3:0] and NWS1 controls D[7:4]. All Nibble Write Selects are sampled on the same edge as the data. Deselecting a Nibble Write Select causes the corresponding nibble of data to be ignored and not written into the device. NWS0,NWS1 BWS0, BWS1, BWS2, BWS3 InputSynchronous Byte Write Select 0, 1, 2 and 3 − Active LOW. Sampled on the rising edge of the K and K clocks during Write operations. Used to select which byte is written into the device during the current portion of the Write operations. Bytes not written remain unaltered. CY7C1425AV18 − BWS0 controls D[8:0] CY7C1412AV18 − BWS0 controls D[8:0], BWS1 controls D[17:9]. CY7C1414AV18 − BWS0 controls D[8:0], BWS1 controls D[17:9],BWS2 controls D[26:18] and BWS3 controls D[35:27]. All the Byte Write Selects are sampled on the same edge as the data. Deselecting a Byte Write Select causes the corresponding byte of data to be ignored and not written into the device. A InputSynchronous Address Inputs. Sampled on the rising edge of the K (Read address) and K (Write address) clocks during active Read and Write operations. These address inputs are multiplexed for both Read and Write operations. Internally, the device is organized as 4M x 8 (2 arrays each of 2M x 8) for CY7C1410AV18, 4M x 9 (2 arrays each of 2M x 9) for CY7C1425AV18, 2M x 18 (2 arrays each of 1M x 18) for CY7C1412AV18 and 1M x 36 (2 arrays each of 512K x 36) for CY7C1414AV18. Therefore, only 21 address inputs are needed to access the entire memory array of CY7C1410AV18 and CY7C1425AV18, 20 address inputs for CY7C1412AV18 and 19 address inputs for CY7C1414AV18. These inputs are ignored when the appropriate port is deselected. Q[x:0] OutputsSynchronous Data Output signals. These pins drive out the requested data during a Read operation. Valid data is driven out on the rising edge of both the C and C clocks during Read operations or K and K when in single clock mode. When the Read port is deselected, Q[x:0] are automatically tri-stated. CY7C1410AV18 − Q[7:0] CY7C1425AV18 − Q[8:0] CY7C1412AV18 − Q[17:0] CY7C1414AV18 − Q[35:0] RPS InputSynchronous Read Port Select, Active LOW. Sampled on the rising edge of Positive Input Clock (K). When active, a Read operation is initiated. Deasserting causes the Read port to be deselected. When deselected, the pending access is allowed to complete and the output drivers are automatically tri-stated following the next rising edge of the C clock. Each read access consists of a burst of two sequential transfers. C Input-Clock Positive Input Clock for Output Data. C is used in conjunction with C to clock out the Read data from the device. C and C can be used together to deskew the flight times of various devices on the board back to the controller. See application example for further details. C Input-Clock Negative Input Clock for Output Data. C is used in conjunction with C to clock out the Read data from the device. C and C can be used together to deskew the flight times of various devices on the board back to the controller. See application example for further details. Document #: 38-05615 Rev. *D Page 6 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 Pin Definitions (continued) Pin Name IO Pin Description K Input-Clock Positive Input Clock Input. The rising edge of K is used to capture synchronous inputs to the device and to drive out data through Q[x:0] when in single clock mode. All accesses are initiated on the rising edge of K. K Input-Clock Negative Input Clock Input. K is used to capture synchronous inputs being presented to the device and to drive out data through Q[x:0] when in single clock mode. CQ Echo Clock CQ is referenced with respect to C. This is a free running clock and is synchronized to the Input clock for output data (C) of the QDR-II. In the single clock mode, CQ is generated with respect to K. The timings for the echo clocks are shown in the AC Timing table. CQ Echo Clock ZQ Input CQ is referenced with respect to C. This is a free running clock and is synchronized to the Input clock for output data (C) of the QDR-II. In the single clock mode, CQ is generated with respect to K. The timings for the echo clocks are shown in the AC Timing table. Output Impedance Matching Input. This input is used to tune the device outputs to the system data bus impedance. CQ, CQ, and Q[x:0] output impedance are set to 0.2 x RQ, where RQ is a resistor connected between ZQ and ground. Alternately, this pin can be connected directly to VDDQ, which enables the minimum impedance mode. This pin cannot be connected directly to GND or left unconnected. DOFF Input TDO Output DLL Turn Off, Active LOW. Connecting this pin to ground turns off the DLL inside the device. The timings in the DLL turned off operation is different from those listed in this data sheet. TDO for JTAG. TCK Input TCK pin for JTAG. TDI Input TDI pin for JTAG. TMS Input TMS pin for JTAG. NC N/A Not connected to the die. Can be tied to any voltage level. NC/72M N/A Not connected to the die. Can be tied to any voltage level. NC/144M N/A Not connected to the die. Can be tied to any voltage level. NC/288M N/A Not connected to the die. Can be tied to any voltage level. VREF InputReference VDD Power Supply VSS Ground VDDQ Power Supply Reference Voltage Input. Static input used to set the reference level for HSTL inputs and Outputs as well as AC measurement points. Power supply inputs to the core of the device. Ground for the device. Power supply inputs for the outputs of the device. Functional Overview The CY7C1410AV18, CY7C1425AV18, CY7C1412AV18 and CY7C1414AV18 are synchronous pipelined Burst SRAMs equipped with both a Read port and a Write port. The Read port is dedicated to Read operations and the Write port is dedicated to Write operations. Data flows into the SRAM through the Write port and out through the Read port. These devices multiplex the address inputs in order to minimize the number of address pins required. By having separate Read and Write ports, the QDR-II completely eliminates the need to “turn-around” the data bus and avoids any possible data contention, thereby simplifying system design. Each access consists of two 8-bit data transfers in the case of CY7C1410AV18, two 9-bit data transfers in the case of CY7C1425AV18,two 18-bit data transfers in the case of CY7C1412AV18 and two 36-bit data transfers in the case of CY7C1414AV18, in one clock cycle. Document #: 38-05615 Rev. *D Accesses for both ports are initiated on the rising edge of the positive Input Clock (K). All synchronous input timings are referenced from the rising edge of the input clocks (K and K) and all output timings are referenced to the rising edge of output clocks (C and C or K and K when in single clock mode). All synchronous data inputs (D[x:0]) inputs pass through input registers controlled by the input clocks (K and K). All synchronous data outputs (Q[x:0]) outputs pass through output registers controlled by the rising edge of the output clocks (C and C or K and K when in single clock mode). All synchronous control (RPS, WPS, BWS[x:0]) inputs pass through input registers controlled by the rising edge of the input clocks (K and K). CY7C1412AV18 is described in the following sections. The same basic descriptions apply to CY7C1410AV18, CY7C1425AV18, and CY7C1414AV18. Page 7 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 Read Operations Concurrent Transactions The CY7C1412AV18 is organized internally as 2 arrays of 1Mx18. Accesses are completed in a burst of two sequential 18-bit data words. Read operations are initiated by asserting RPS active at the rising edge of the Positive Input Clock (K). The address is latched on the rising edge of the K Clock. The address presented to Address inputs is stored in the Read address register. Following the next K clock rise the corresponding lowest order 18-bit word of data is driven onto the Q[17:0] using C as the output timing reference. On the subsequent rising edge of C, the next 18-bit data word is driven onto the Q[17:0]. The requested data is valid 0.45 ns from the rising edge of the output clock (C and C or K and K when in single clock mode). The Read and Write ports on the CY7C1412AV18 operate completely independently of one another. While each port latches the address inputs on different clock edges, the user can Read or Write to any location, regardless of the transaction on the other port. Also, reads and writes can be started in the same clock cycle. If the ports access the same location at the same time, the SRAM delivers the most recent information associated with the specified address location. This includes forwarding data from a Write cycle that was initiated on the previous K clock rise. Synchronous internal circuitry automatically tri-states the outputs following the next rising edge of the Output Clocks (C/C). This allows for a seamless transition between devices without the insertion of wait states in a depth expanded memory. Write Operations Write operations are initiated by asserting WPS active at the rising edge of the Positive Input Clock (K). On the same K clock rise, the data presented to D[17:0] is latched and stored into the lower 18-bit Write Data register provided BWS[1:0] are both asserted active. On the subsequent rising edge of the Negative Input Clock (K), the address is latched and the information presented to D[17:0] is stored into the Write Data register provided BWS[1:0] are both asserted active. The 36 bits of data are then written into the memory array at the specified location. When deselected, the write port ignores all inputs after the pending Write operations have been completed. Byte Write Operations Byte Write operations are supported by the CY7C1412AV18. A Write operation is initiated as described in the Write Operations section above. The bytes that are written are determined by BWS0 and BWS1, which are sampled with each 18-bit data word. Asserting the appropriate Byte Write Select input during the data portion of a Write allows the data being presented to be latched and written into the device. Deasserting the Byte Write Select input during the data portion of a write allows the data stored in the device for that byte to remain unaltered. This feature can be used to simplify Read/Modify/Write operations to a Byte Write operation. Single Clock Mode The CY7C1412AV18 can be used with a single clock that controls both the input and output registers. In this mode, the device recognizes only a single pair of input clocks (K and K) that control both the input and output registers. This operation is identical to the operation if the device had zero skew between the K/K and C/C clocks. All timing parameters remain the same in this mode. To use this mode of operation, the user must tie C and C HIGH at power on. This function is a strap option and not alterable during device operation. Document #: 38-05615 Rev. *D Depth Expansion The CY7C1412AV18 has a Port Select input for each port. This allows for easy depth expansion. Both Port Selects are sampled on the rising edge of the Positive Input Clock only (K). Each port select input can deselect the specified port. Deselecting a port does not affect the other port. All pending transactions (Read and Write) are completed prior to the device being deselected. Programmable Impedance An external resistor, RQ, must be connected between the ZQ pin on the SRAM and VSS to allow the SRAM to adjust its output driver impedance. The value of RQ must be 5x the value of the intended line impedance driven by the SRAM. The allowable range of RQ to guarantee impedance matching with a tolerance of ±15% is between 175Ω and 350Ω, with VDDQ = 1.5V.The output impedance is adjusted every 1024 cycles upon power up to account for drifts in supply voltage and temperature. Echo Clocks Echo clocks are provided on the QDR-II to simplify data capture on high-speed systems. Two echo clocks are generated by the QDR-II. CQ is referenced with respect to C and CQ is referenced with respect to C. These are free-running clocks and are synchronized to the output clock (C/C) of the QDR-II. In the single clock mode, CQ is generated with respect to K and CQ is generated with respect to K. The timings for the echo clocks are shown in the AC Timing table. DLL These chips use a Delay Lock Loop (DLL) that is designed to function between 80 MHz and the specified maximum clock frequency. During power up, when the DOFF is tied HIGH, the DLL gets locked after 1024 cycles of stable clock. The DLL can also be reset by slowing or stopping the input clock K and K for a minimum of 30 ns. However, it is not necessary for the DLL to be specifically reset in order to lock the DLL to the desired frequency. The DLL automatically locks 1024 clock cycles after a stable clock is presented.the DLL may be disabled by applying ground to the DOFF pin. For information refer to the application note “DLL Considerations in QDRII/DDRII/QDRII+/DDRII+”. Page 8 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 Application Example[1] R = 250οηµσ SRAM #1 R P S # Vt D A R W P S # B W S # SRAM #4 ZQ CQ/CQ# Q C C# K K# R P S # D A DATA IN DATA OUT Address RPS# BUS WPS# MASTER BWS# (CPU CLKIN/CLKIN# or Source K ASIC) Source K# R W P S # B W S # ZQ R = 250οηµσ CQ/CQ# Q C C# K K# Vt Vt Delayed K Delayed K# R R = 50οηµσ Vt = Vddq/2 Truth Table[2, 3, 4, 5, 6, 7] Operation K RPS WPS Write Cycle: Load address on the rising edge of K clock; input write data on K and K rising edges. L-H X L D(A + 0) at K(t) ↑ Read Cycle: Load address on the rising edge of K clock; wait one and a half cycle; read data on C and C rising edges. L-H L X Q(A + 0) at C(t + 1) ↑ Q(A + 1) at C(t + 2) ↑ NOP: No Operation L-H H H D=X Q = High-Z D=X Q = High-Z Stopped X X Previous State Previous State Standby: Clock Stopped DQ DQ D(A + 1) at K(t) ↑ Write Cycle Descriptions (CY7C1410AV18 and CY7C1412AV18) [2, 8] BWS0/NWS0 BWS1/NWS1 K K Comments L L L-H – During the data portion of a write sequence: CY7C1410AV18 − both nibbles (D[7:0]) are written into the device, CY7C1412AV18 − both bytes (D[17:0]) are written into the device. L L – L-H During the data portion of a write sequence: CY7C1410AV18 − both nibbles (D[7:0]) are written into the device, CY7C1412AV18 − both bytes (D[17:0]) are written into the device. L H L-H – During the data portion of a write sequence: CY7C1410AV18 − only the lower nibble (D[3:0]) is written into the device. D[7:4] remains unaltered, CY7C1412AV18 − only the lower byte (D[8:0]) is written into the device. D[17:9] remains unaltered. Notes: 1. The above application shows four QDR-II being used. 2. X = “Don't Care,” H = Logic HIGH, L= Logic LOW, ↑represents rising edge. 3. Device powers up deselected and the outputs in a tri-state condition. 4. “A” represents address location latched by the devices when transaction was initiated. A + 00, A + 01 represents the internal address sequence in the burst. 5. “t” represents the cycle at which a Read/Write operation is started. t + 1 and t + 2 are the first and second clock cycles respectively succeeding the “t” clock cycle. 6. Data inputs are registered at K and K rising edges. Data outputs are delivered on C and C rising edges, except when in single clock mode. 7. It is recommended that K = K and C = C = HIGH when clock is stopped. This is not essential, but permits most rapid restart by overcoming transmission line charging symmetrically. 8. Assumes a Write cycle was initiated according to the Write Port Cycle Description Truth Table. NWS0, NWS1, BWS0, BWS1, BWS2 and BWS3 can be altered on different portions of a Write cycle, as long as the setup and hold requirements are achieved. Document #: 38-05615 Rev. *D Page 9 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 Write Cycle Descriptions (CY7C1410AV18 and CY7C1412AV18) (continued)[2, 8] BWS0/NWS0 BWS1/NWS1 K K Comments L H – L-H During the data portion of a write sequence: CY7C1410AV18 − only the lower nibble (D[3:0]) is written into the device. D[7:4] remains unaltered, CY7C1412AV18 − only the lower byte (D[8:0]) is written into the device. D[17:9] remains unaltered. H L L-H – During the data portion of a write sequence: CY7C1410AV18 − only the upper nibble (D[7:4]) is written into the device. D[3:0] remains unaltered, CY7C1412AV18 − only the upper byte (D[17:9]) is written into the device. D[8:0] remains unaltered. H L – L-H During the data portion of a write sequence: CY7C1410AV18 − only the upper nibble (D[7:4]) is written into the device. D[3:0] remains unaltered, CY7C1412AV18 − only the upper byte (D[17:9]) is written into the device. D[8:0] remains unaltered. H H L-H – No data is written into the devices during this portion of a write operation. H H – L-H No data is written into the devices during this portion of a write operation. Write Cycle Descriptions (CY7C1414AV18) [2, 8] BWS0 BWS1 BWS2 BWS3 K K Comments L L L L L-H – L L L L – L-H L H H H L-H – L H H H – L-H H L H H L-H – H L H H – L-H H H L H L-H – H H L H – L-H H H H L L-H H H H L – L-H H H H H H H H H L-H – – L-H During the data portion of a write sequence, all four bytes (D[35:0]) are written into the device. During the data portion of a write sequence, all four bytes (D[35:0]) are written into the device. During the data portion of a write sequence, only the lower byte (D[8:0]) is written into the device. D[35:9] remains unaltered. During the data portion of a write sequence, only the lower byte (D[8:0]) is written into the device. D[35:9] remains unaltered. During the data portion of a write sequence, only the byte (D[17:9]) is written into the device. D[8:0] and D[35:18] remains unaltered. During the data portion of a write sequence, only the byte (D[17:9]) is written into the device. D[8:0] and D[35:18] remains unaltered. During the data portion of a write sequence, only the byte (D[26:18]) is written into the device. D[17:0] and D[35:27] remains unaltered. During the data portion of a write sequence, only the byte (D[26:18]) is written into the device. D[17:0] and D[35:27] remains unaltered. During the data portion of a write sequence, only the byte (D[35:27]) is written into the device. D[26:0] remains unaltered. During the data portion of a write sequence, only the byte (D[35:27]) is written into the device. D[26:0] remains unaltered. No data is written into the device during this portion of a write operation. No data is written into the device during this portion of a write operation. Write Cycle Descriptions (CY7C1425AV18) BWS0 K K L L-H – L – L-H H H L-H – – L-H Comments During the data portion of a write sequence: CY7C1425AV18 - the single byte (D[8:0]) is written into the device During the data portion of a write sequence: CY7C1425AV18 - the single byte (D[8:0]) is written into the device No data is written into the devices during this portion of a Write operation. No data is written into the devices during this portion of a Write operation. Document #: 38-05615 Rev. *D Page 10 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 IEEE 1149.1 Serial Boundary Scan (JTAG) These SRAMs incorporate a serial boundary scan test access port (TAP) in the FBGA package. This part is fully compliant with IEEE Standard #1149.1-1900. The TAP operates using JEDEC standard 1.8V IO logic levels. Disabling the JTAG Feature Upon power up, the instruction register is loaded with the IDCODE instruction. It is also loaded with the IDCODE instruction if the controller is placed in a reset state as described in the previous section. When the TAP controller is in the Capture IR state, the two least significant bits are loaded with a binary “01” pattern to allow for fault isolation of the board level serial test path. It is possible to operate the SRAM without using the JTAG feature. To disable the TAP controller, TCK must be tied LOW (VSS) to prevent clocking of the device. TDI and TMS are internally pulled up and may be unconnected. They may alternately be connected to VDD through a pull up resistor. TDO must be left unconnected. Upon power up, the device is up in a reset state which does not interfere with the operation of the device. Bypass Register Test Access Port—Test Clock Boundary Scan Register The test clock is used only with the TAP controller. All inputs are captured on the rising edge of TCK. All outputs are driven from the falling edge of TCK. Test Mode Select The TMS input is used to give commands to the TAP controller and is sampled on the rising edge of TCK. It is allowable to leave this pin unconnected if the TAP is not used. The pin is pulled up internally, resulting in a logic HIGH level. Test Data-In (TDI) The TDI pin is used to serially input information into the registers and can be connected to the input of any of the registers. The register between TDI and TDO is chosen by the instruction that is loaded into the TAP instruction register. For information on loading the instruction register, see the TAP Controller State Diagram. TDI is internally pulled up and can be unconnected if the TAP is unused in an application. TDI is connected to the most significant bit (MSB) on any register. Test Data-Out (TDO) The TDO output pin is used to serially clock data-out from the registers. The output is active depending upon the current state of the TAP state machine (see Instruction codes). The output changes on the falling edge of TCK. TDO is connected to the least significant bit (LSB) of any register. Performing a TAP Reset A Reset is performed by forcing TMS HIGH (VDD) for five rising edges of TCK. This RESET does not affect the operation of the SRAM and may be performed while the SRAM is operating. At power up, the TAP is reset internally to ensure that TDO comes up in a high-Z state. TAP Registers Registers are connected between the TDI and TDO pins and allow data to be scanned into and out of the SRAM test circuitry. Only one register can be selected at a time through the instruction registers. Data is serially loaded into the TDI pin on the rising edge of TCK. Data is output on the TDO pin on the falling edge of TCK. Instruction Register Three-bit instructions can be serially loaded into the instruction register. This register is loaded when it is placed between the TDI and TDO pins as shown in TAP Controller Block Diagram. Document #: 38-05615 Rev. *D To save time when serially shifting data through registers, it is sometimes advantageous to skip certain chips. The bypass register is a single-bit register that can be placed between TDI and TDO pins. This allows data to be shifted through the SRAM with minimal delay. The bypass register is set LOW (VSS) when the BYPASS instruction is executed. The boundary scan register is connected to all of the input and output pins on the SRAM. Several no connect (NC) pins are also included in the scan register to reserve pins for higher density devices. The boundary scan register is loaded with the contents of the RAM Input and Output ring when the TAP controller is in the Capture-DR state and is then placed between the TDI and TDO pins when the controller is moved to the Shift-DR state. The EXTEST, SAMPLE/PRELOAD and SAMPLE Z instructions can be used to capture the contents of the Input and Output ring. The Boundary Scan Order tables show the order in which the bits are connected. Each bit corresponds to one of the bumps on the SRAM package. The MSB of the register is connected to TDI, and the LSB is connected to TDO. Identification (ID) Register The ID register is loaded with a vendor-specific, 32-bit code during the Capture-DR state when the IDCODE command is loaded in the instruction register. The IDCODE is hardwired into the SRAM and can be shifted out when the TAP controller is in the Shift-DR state. The ID register has a vendor code and other information described in the Identification Register Definitions table. TAP Instruction Set Eight different instructions are possible with the three-bit instruction register. All combinations are listed in the Instruction Code table. Three of these instructions are listed as RESERVED and must not be used. The other five instructions are described in detail below. Instructions are loaded into the TAP controller during the Shift-IR state when the instruction register is placed between TDI and TDO. During this state, instructions are shifted through the instruction register through the TDI and TDO pins. To execute the instruction after it is shifted in, the TAP controller needs to be moved into the Update-IR state. IDCODE The IDCODE instruction causes a vendor-specific, 32-bit code to be loaded into the instruction register. It also places the instruction register between the TDI and TDO pins and allows the IDCODE to be shifted out of the device when the TAP controller enters the Shift-DR state. The IDCODE instruction Page 11 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 is loaded into the instruction register upon power up or whenever the TAP controller is supplied a test logic reset state. SAMPLE Z The SAMPLE Z instruction causes the boundary scan register to be connected between the TDI and TDO pins when the TAP controller is in a Shift-DR state. The SAMPLE Z command puts the output bus into a High-Z state until the next command is supplied during the “Update IR” state. SAMPLE/PRELOAD SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When the SAMPLE/PRELOAD instructions are loaded into the instruction register and the TAP controller is in the Capture-DR state, a snapshot of data on the inputs and output pins is captured in the boundary scan register. The user must be aware that the TAP controller clock can only operate at a frequency up to 20 MHz, while the SRAM clock operates more than an order of magnitude faster. Because there is a large difference in the clock frequencies, it is possible that during the Capture-DR state, an input or output undergoes a transition. The TAP may then try to capture a signal while in transition (metastable state). This does not harm the device, but there is no guarantee as to the value that is captured. Repeatable results may not be possible. To guarantee that the boundary scan register captures the correct value of a signal, the SRAM signal must be stabilized long enough to meet the TAP controller's capture setup plus hold times (tCS and tCH). The SRAM clock input might not be captured correctly if there is no way in a design to stop (or slow) the clock during a SAMPLE/PRELOAD instruction. If this is an issue, it is still possible to capture all other signals and simply ignore the value of the CK and CK captured in the boundary scan register. After the data is captured, it is possible to shift out the data by putting the TAP into the Shift-DR state. This places the boundary scan register between the TDI and TDO pins. PRELOAD allows an initial data pattern to be placed at the latched parallel outputs of the boundary scan register cells prior to the selection of another boundary scan test operation. BYPASS When the BYPASS instruction is loaded in the instruction register and the TAP is placed in a Shift-DR state, the bypass register is placed between the TDI and TDO pins. The advantage of the BYPASS instruction is that it shortens the boundary scan path when multiple devices are connected together on a board. EXTEST The EXTEST instruction enables the preloaded data to be driven out through the system output pins. This instruction also selects the boundary scan register to be connected for serial access between the TDI and TDO in the shift-DR controller state. EXTEST OUTPUT BUS TRI-STATE IEEE Standard 1149.1 mandates that the TAP controller be able to put the output bus into a tri-state mode. The boundary scan register has a special bit located at bit #108. When this scan cell, called the “extest output bus tri-state,” is latched into the preload register during the “Update-DR” state in the TAP controller, it directly controls the state of the output (Q-bus) pins, when the EXTEST is entered as the current instruction. When HIGH, it enables the output buffers to drive the output bus. When LOW, this bit places the output bus into a High-Z condition. This bit can be set by entering the SAMPLE/PRELOAD or EXTEST command, and then shifting the desired bit into that cell, during the “Shift-DR” state. During “Update-DR”, the value loaded into that shift-register cell latches into the preload register. When the EXTEST instruction is entered, this bit directly controls the output Q-bus pins. Note that this bit is pre-set LOW to enable the output when the device is powered-up, and also when the TAP controller is in the “Test-Logic-Reset” state. Reserved These instructions are not implemented but are reserved for future use. Do not use these instructions. The shifting of data for the SAMPLE and PRELOAD phases can occur concurrently when required—that is, while data captured is shifted out, the preloaded data can be shifted in. Document #: 38-05615 Rev. *D Page 12 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 TAP Controller State Diagram[9] 1 TEST-LOGIC RESET 0 0 TEST-LOGIC/ IDLE 1 1 SELECT DR-SCAN 0 0 1 1 CAPTURE-DR CAPTURE-IR 0 0 0 SHIFT-DR 1 1 EXIT1-DR 1 EXIT1-IR 0 0 PAUSE-DR 0 0 PAUSE-IR 1 1 0 EXIT2-DR EXIT2-IR 1 1 UPDATE-DR 1 0 SHIFT-IR 1 0 1 SELECT IR-SCAN 0 UPDATE-IR 1 0 Note: 9. The 0/1 next to each state represents the value at TMS at the rising edge of TCK. Document #: 38-05615 Rev. *D Page 13 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 TAP Controller Block Diagram 0 Bypass Register Selection Circuitry 2 TDI 1 0 1 0 Selection Circuitry TDO Instruction Register 31 30 29 . . 2 Identification Register 106 . . . . 2 1 0 Boundary Scan Register TCK TAP Controller TMS TAP Electrical Characteristics Over the Operating Range[15, 18, 10] Parameter Description Test Conditions Min VOH1 Output HIGH Voltage IOH = −2.0 mA 1.4 VOH2 Output HIGH Voltage IOH = −100 µA 1.6 VOL1 Output LOW Voltage IOL = 2.0 mA IOL = 100 µA VOL2 Output LOW Voltage VIH Input HIGH Voltage VIL Input LOW Voltage IX Input and OutputLoad Current GND ≤ VI ≤ VDD Max Unit V V 0.4 V 0.2 V 0.65VDD VDD + 0.3 V –0.3 0.35VDD V −5 5 µA Note: 10. These characteristic pertain to the TAP inputs (TMS, TCK, TDI and TDO). Parallel load levels are specified in the Electrical Characteristics table. Document #: 38-05615 Rev. *D Page 14 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 TAP AC Switching Characteristics Over the Operating Range[11, 12] Parameter Description Min Max Unit 20 MHz tTCYC TCK Clock Cycle Time tTF TCK Clock Frequency tTH TCK Clock HIGH 20 ns tTL TCK Clock LOW 20 ns tTMSS TMS Setup to TCK Clock Rise 5 ns tTDIS TDI Setup to TCK Clock Rise 5 ns tCS Capture Setup to TCK Rise 5 ns tTMSH TMS Hold after TCK Clock Rise 5 ns tTDIH TDI Hold after Clock Rise 5 ns tCH Capture Hold after Clock Rise 5 ns 50 ns Setup Times Hold Times Output Times tTDOV TCK Clock LOW to TDO Valid tTDOX TCK Clock LOW to TDO Invalid 10 0 ns ns TAP Timing and Test Conditions[12] 0.9V 50Ω ALL INPUT PULSES 1.8V TDO 0.9V Z0 = 50Ω 0V CL = 20 pF tTH tTL GND (a) Test Clock TCK tTCYC tTMSS tTMSH Test Mode Select TMS tTDIS tTDIH Test Data-In TDI Test Data-Out TDO tTDOV tTDOX Notes: 11. tCS and tCH refer to the setup and hold time requirements of latching data from the boundary scan register. 12. Test conditions are specified using the load in TAP AC test conditions. tR/tF = 1 ns. Document #: 38-05615 Rev. *D Page 15 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 Identification Register Definitions Value Instruction Field CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 000 000 000 000 Revision Number (31:29) Cypress Device ID (28:12) Description Version number. 11010011010000111 11010011010001111 11010011010010111 11010011010100111 Defines the type of SRAM. Cypress JEDEC ID (11:1) 00000110100 00000110100 00000110100 00000110100 1 1 1 1 ID Register Presence (0) Unique identification of SRAM vendor. Indicates the presence of an ID register. Scan Register Sizes Register Name Bit Size Instruction 3 Bypass 1 ID 32 Boundary Scan Cells 109 Instruction Codes Instruction Code Description EXTEST 000 Captures the Input/Output ring contents. IDCODE 001 Loads the ID register with the vendor ID code and places the register between TDI and TDO. This operation does not affect SRAM operation. SAMPLE Z 010 Captures the Input/Output contents. Places the boundary scan register between TDI and TDO. Forces all SRAM output drivers to a High-Z state. RESERVED 011 Do Not Use: This instruction is reserved for future use. SAMPLE/PRELOAD 100 Captures the Input/Output ring contents. Places the boundary scan register between TDI and TDO. Does not affect the SRAM operation. RESERVED 101 Do Not Use: This instruction is reserved for future use. RESERVED 110 Do Not Use: This instruction is reserved for future use. BYPASS 111 Places the bypass register between TDI and TDO. This operation does not affect SRAM operation. Document #: 38-05615 Rev. *D Page 16 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 Boundary Scan Order Bit # Bump ID Bit # Bump ID Bit # Bump ID Bit # Bump ID 0 6R 28 10G 56 6A 84 1J 1 6P 29 9G 57 5B 85 2J 2 6N 30 11F 58 5A 86 3K 3 7P 31 11G 59 4A 87 3J 4 7N 32 9F 60 5C 88 2K 5 7R 33 10F 61 4B 89 1K 6 8R 34 11E 62 3A 90 2L 7 8P 35 10E 63 2A 91 3L 8 9R 36 10D 64 1A 92 1M 9 11P 37 9E 65 2B 93 1L 10 10P 38 10C 66 3B 94 3N 11 10N 39 11D 67 1C 95 3M 12 9P 40 9C 68 1B 96 1N 13 10M 41 9D 69 3D 97 2M 14 11N 42 11B 70 3C 98 3P 15 9M 43 11C 71 1D 99 2N 16 9N 44 9B 72 2C 100 2P 17 11L 45 10B 73 3E 101 1P 18 11M 46 11A 74 2D 102 3R 19 9L 47 10A 75 2E 103 4R 20 10L 48 9A 76 1E 104 4P 21 11K 49 8B 77 2F 105 5P 22 10K 50 7C 78 3F 106 5N 23 9J 51 6C 79 1G 107 5R 24 9K 52 8A 80 1F 108 Internal 25 10J 53 7A 81 3G 26 11J 54 7B 82 2G 27 11H 55 6B 83 1H Document #: 38-05615 Rev. *D Page 17 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 Power Up Sequence in QDR-II SRAM[13, 14] DLL Constraints QDR-II SRAMs must be powered up and initialized in a predefined manner to prevent undefined operations. • DLL uses either K or C clock as its synchronizing input.The input must have low phase jitter, which is specified as tKC Var. Power Up Sequence • The DLL functions at frequencies down to 80MHz. • Apply power and drive DOFF LOW (All other inputs can be HIGH or LOW) — Apply VDD before VDDQ — Apply VDDQ before VREF or at the same time as VREF • If the input clock is unstable and the DLL is enabled, then the DLL may lock to an incorrect frequency, causing unstable SRAM behavior. • After the power and clock (K, K, C, C) are stable take DOFF HIGH • The additional 1024 cycles of clocks are required for the DLL to lock. ~ ~ Power Up Waveforms K K ~ ~ Unstable Clock > 1024 Stable clock Start Normal Operation Clock Start (Clock Starts after V DD / V DDQ Stable) VDD / VDDQ DOFF V DD / V DDQ Stable (< +/- 0.1V DC per 50ns ) Fix High (or tied to VDDQ) Notes: 13. It is recommended that the DOFF pin be pulled HIGH via a pull up resistor of 1 Kohm. 14. During Power Up, when the DOFF is tied HIGH, the DLL gets locked after 1024 cycles of stable clock. Document #: 38-05615 Rev. *D Page 18 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 DC Input Voltage[18]............................... –0.5V to VDD + 0.3V Maximum Ratings Exceeding maximum ratings may impair the useful life of the device. These user guidelines are not tested. Storage Temperature ................................. –65°C to +150°C Ambient Temperature with Power Applied........................................... ––55°C to +125°C Current into Outputs (LOW)......................................... 20 mA Static Discharge Voltage.......................................... > 2001V (MIL-STD-883, Method 3015) Latch up Current.................................................... > 200 mA Operating Range Supply Voltage on VDD Relative to GND........ –0.5V to +2.9V Supply Voltage on VDDQ Relative to GND ...... –0.5V to +VDD DC Voltage Applied to Outputs in High-Z State .................................... –0.5V to VDDQ + 0.3V Range Ambient Temperature (TA) VDD[19] VDDQ[19] 0°C to +70°C 1.8 ± 0.1V 1.4V to VDD Com’l Ind’l –40°C to +85°C Electrical Characteristics Over the Operating Range[15, 19] DC Electrical Characteristics Over the Operating Range Parameter Description Test Conditions Min Typ Max Unit VDD Power Supply Voltage 1.7 1.8 1.9 V VDDQ IO Supply Voltage 1.4 1.5 VDD V VOH Output HIGH Voltage Note 16 VDDQ/2 – 0.12 VDDQ/2 + 0.12 V VOL Output LOW Voltage Note 17 VDDQ/2 – 0.12 VDDQ/2 + 0.12 V VOH(LOW) Output HIGH Voltage IOH = −0.1 mA, Nominal Impedance VDDQ – 0.2 VDDQ V VOL(LOW) Output LOW Voltage IOL = 0.1 mA, Nominal Impedance VSS 0.2 V VIH Input HIGH Voltage[18] VREF + 0.1 VDDQ+0.3 V VIL Input LOW Voltage[18] –0.3 VREF – 0.1 V IX Input Leakage Current GND ≤ VI ≤ VDDQ −5 5 µA IOZ Output Leakage Current GND ≤ VI ≤ VDDQ, Output Disabled −5 5 µA VREF Input Reference Voltage[20] Typical Value = 0.75V IDD VDD Operating Supply ISB1 Automatic Power down Current VDD = Max., IOUT = 0 mA, f = fMAX = 1/tCYC 0.68 0.75 0.95 V 740 mA 167 MHz 200 MHz 870 mA 250 MHz 1065 mA Max. VDD, Both Ports 167 MHz Deselected, VIN ≥ VIH 200 MHz or VIN ≤ VIL, f = fMAX = 250 MHz 1/tCYC, Inputs Static 270 mA 300 mA 350 mA AC Input Requirements Over the Operating Range Min Typ Max Unit VIH Parameter Input High (Logic 1) Voltage Description Test Conditions VREF + 0.2 – – V VIL Input Low (Logic 0) Voltage – – VREF – 0.2 V Capacitance[21] Parameter Description CIN Input Capacitance CCLK Clock Input Capacitance CO Output Capacitance Test Conditions TA = 25°C, f = 1 MHz, VDD = 1.8V VDDQ = 1.5V Max Unit 5 pF 4 pF 5 pF Notes: 15. All voltage referenced to Ground. 16. Output are impedance controlled. IOH = –(VDDQ/2)/(RQ/5) for values of 175Ω <= RQ <= 350Ωs. 17. Output are impedance controlled. IOL = (VDDQ/2)/(RQ/5) for values of 175Ω <= RQ <= 350Ω. 18. Overshoot: VIH(AC) < VDDQ +0.85V (Pulse width less than tCYC/2), Undershoot: VIL(AC) > –1.5V (Pulse width less than tCYC/2). 19. Power up: Assumes a linear ramp from 0V to VDD(min.) within 200 ms. During this time VIH< VDD and VDDQ< VDD. 20. VREF (Min.) = 0.68V or 0.46VDDQ, whichever is larger, VREF (Max.) = 0.95V or 0.54VDDQ, whichever is smaller. 21. Tested initially and after any design or process change that may affect these parameters. Document #: 38-05615 Rev. *D Page 19 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 Thermal Resistance[21] Parameter Description Thermal Resistance ΘJA (Junction to Ambient) ΘJC Thermal Resistance (Junction to Case) Test Conditions Test conditions follow standard test methods and procedures for measuring thermal impedance, according to EIA/JESD51. 165 FBGA Package 17.2 Unit °C/W 3.2 °C/W AC Test Loads and Waveforms VREF = 0.75V VREF 0.75V VREF OUTPUT Z0 = 50Ω Device Under Test ZQ RL = 50Ω VREF = 0.75V RQ = 250Ω 0.75V R = 50Ω ALL INPUT PULSES 1.25V 0.75V OUTPUT Device Under Test ZQ 5 pF [22] 0.25V Slew Rate = 2 V/ns RQ = 250Ω (a) (b) Note: 22. Unless otherwise noted, test conditions assume signal transition time of 2V/ns, timing reference levels of 0.75V, Vref = 0.75V, RQ = 250Ω, VDDQ = 1.5V, input pulse levels of 0.25V to 1.25V, and output loading of the specified IOL/IOH and load capacitance shown in (a) of AC Test Loads. Document #: 38-05615 Rev. *D Page 20 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 Switching Characteristics Over the Operating Range [22, 23] 250 MHz Cypress Consortium Parameter Parameter Description VDD(Typical) to the first Access tPOWER Min [26] Max 1 200 MHz Min Max 1 167 MHz Min Max 1 Unit ms tCYC tKHKH K Clock and C Clock Cycle Time 4.0 6.3 5.0 7.9 6.0 8.4 ns tKH tKHKL Input Clock (K/K and C/C) HIGH 1.6 – 2.0 – 2.4 – ns tKL tKLKH Input Clock (K/K and C/C) LOW 1.6 – 2.0 – 2.4 – ns tKHKH tKHKH K Clock Rise to K Clock Rise and C to C Rise (rising edge to rising edge) 1.8 – 2.2 – 2.7 – ns tKHCH tKHCH K/K Clock Rise to C/C Clock Rise (rising edge to rising edge) 0.0 1.8 0.0 2.2 0.0 2.7 ns Setup Times tSA tAVKH Address Setup to K Clock Rise 0.35 – 0.4 – 0.5 – ns tSC tIVKH Control Setup to K Clock Rise (RPS, WPS) 0.35 – 0.4 – 0.5 – ns tSCDDR tIVKH Double Data Rate Control Setup to Clock (K, K) Rise (BWS0, BWS1, BWS3, BWS4) 0.35 – 0.4 – 0.5 – ns tSD tDVKH D[X:0] Setup to Clock (K/K) Rise 0.35 – 0.4 – 0.5 – ns Hold Times tHA tKHAX Address Hold after K Clock Rise 0.35 – 0.4 – 0.5 – ns tHC tKHIX Control Hold after K Clock Rise (RPS, WPS) 0.35 – 0.4 – 0.5 – ns tHCDDR tKHIX Double Data Rate Control Hold after Clock (K, K) Rise (BWS0, BWS1, BWS3, BWS4) 0.35 – 0.4 – 0.5 – ns tHD tKHDX D[X:0] Hold after Clock (K/K) Rise 0.35 – 0.4 – 0.5 – ns – 0.45 – 0.45 – 0.50 ns – –0.45 – -0.50 – ns – 0.45 – 0.45 – 0.50 ns –0.45 – –0.45 – –0.50 – ns – 0.30 – 0.35 – 0.40 ns –0.30 – –0.35 – –0.40 – ns – 0.45 – 0.45 – 0.50 ns –0.45 – –0.45 – –0.50 – ns – 0.20 – 0.20 – 0.20 ns Output Times tCO tCHQV C/C Clock Rise (or K/K in Single Clock Mode) to Data Valid tDOH tCHQX Data Output Hold after Output C/C Clock Rise –0.45 (Active to Active) tCCQO tCHCQV C/C Clock Rise to Echo Clock Valid tCQOH tCHCQX Echo Clock Hold after C/C Clock Rise tCQD tCQHQV Echo Clock High to Data Valid tCQDOH tCQHQX Echo Clock High to Data Invalid tCHZ tCHQZ Clock (C/C) Rise to High-Z (Active to High-Z)[24,25] tCLZ tCHQX1 Clock (C/C) Rise to Low-Z[24,25] DLL Timing tKC Var tKC Var Clock Phase Jitter tKC lock tKC lock DLL Lock Time (K, C) 1024 – 1024 – 1024 – cycles tKC Reset tKC Reset K Static to DLL Reset 30 – 30 – 30 – ns Notes: 23. All devices can operate at clock frequencies as low as 119 MHz. When a part with a maximum frequency above 133 MHz is operating at a lower clock frequency, it requires the input timings of the frequency range in which it is being operated and outputs data with the output timings of that frequency range. 24. tCHZ, tCLZ, are specified with a load capacitance of 5 pF as in part (b) of AC Test Loads. Transition is measured ± 100 mV from steady-state voltage. 25. At any voltage and temperature tCHZ is less than tCLZ and tCHZ less than tCO. 26. This part has a voltage regulator internally; tPOWER is the time that the power needs to be supplied above VDD minimum initially before a read or write operation can be initiated. 27. For D2 data signal on CY7C1425AV18 device, tSD is 0.5 ns for 200 MHz, and 250 MHz frequencies. Document #: 38-05615 Rev. *D Page 21 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 Switching Waveforms[28, 29, 30] Read/Write/Deselect Sequence READ WRITE READ WRITE READ WRITE NOP WRITE NOP 1 2 3 4 5 6 7 8 9 10 K tKH tKL tKHKH tCYC K RPS tSC t HC WPS A D A1 A2 tSA tHA tSA tHA D11 D30 A0 D10 A3 A4 A5 D31 D50 D51 tSD Q00 t CLZ C tKL tKH tKHCH D60 D61 tSD tHD tHD Q tKHCH A6 Q01 tDOH tCO Q20 Q21 Q41 Q40 tCQDOH t CHZ tCQD t CYC tKHKH C tCQOH tCCQO CQ tCQOH tCCQO CQ DON’T CARE UNDEFINED Notes: 28. Q00 refers to output from address A0. Q01 refers to output from the next internal burst address following A0, i.e., A0 + 1. 29. Output are disabled (High-Z) one clock cycle after a NOP. 30. In this example, if address A0 = A1, then data Q00 = D10 and Q01 = D11. Write data is forwarded immediately as read results. This note applies to the whole diagram. Document #: 38-05615 Rev. *D Page 22 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 Ordering Information Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or visit www.cypress.com for actual products offered. Speed (MHz) 167 Ordering Code CY7C1410AV18-167BZC Package Diagram Package Type 51-85195 165-Ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Operating Range Commercial CY7C1425AV18-167BZC CY7C1412AV18-167BZC CY7C1414AV18-167BZC CY7C1410AV18-167BZXC 51-85195 165-Ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free CY7C1425AV18-167BZXC CY7C1412AV18-167BZXC CY7C1414AV18-167BZXC CY7C1410AV18-167BZI 51-85195 165-Ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Industrial CY7C1425AV18-167BZI CY7C1412AV18-167BZI CY7C1414AV18-167BZI CY7C1410AV18-167BZXI 51-85195 165-Ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free CY7C1425AV18-167BZXI CY7C1412AV18-167BZXI CY7C1414AV18-167BZXI 200 CY7C1410AV18-200BZC 51-85195 165-Ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Commercial CY7C1425AV18-200BZC CY7C1412AV18-200BZC CY7C1414AV18-200BZC CY7C1410AV18-200BZXC 51-85195 165-Ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free CY7C1425AV18-200BZXC CY7C1412AV18-200BZXC CY7C1414AV18-200BZXC CY7C1410AV18-200BZI 51-85195 165-Ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Industrial CY7C1425AV18-200BZI CY7C1412AV18-200BZI CY7C1414AV18-200BZI CY7C1410AV18-200BZXI 51-85195 165-Ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free CY7C1425AV18-200BZXI CY7C1412AV18-200BZXI CY7C1414AV18-200BZXI 250 CY7C1410AV18-250BZC 51-85195 165-Ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Commercial CY7C1425AV18-250BZC CY7C1412AV18-250BZC CY7C1414AV18-250BZC CY7C1410AV18-250BZXC 51-85195 165-Ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free CY7C1425AV18-250BZXC CY7C1412AV18-250BZXC CY7C1414AV18-250BZXC Document #: 38-05615 Rev. *D Page 23 of 25 CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 Ordering Information (continued) Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or visit www.cypress.com for actual products offered. Speed (MHz) 250 Package Diagram Ordering Code CY7C1410AV18-250BZI Operating Range Package Type 51-85195 165-Ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Industrial CY7C1425AV18-250BZI CY7C1412AV18-250BZI CY7C1414AV18-250BZI CY7C1410AV18-250BZXI 51-85195 165-Ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free CY7C1425AV18-250BZXI CY7C1412AV18-250BZXI CY7C1414AV18-250BZXI Package Diagram 165-Ball FBGA (15 x 17 x 1.40 mm) (51-85195) "/44/-6)%7 4/06)%7 0).#/2.%2 -# -#!" 0).#/2.%2 8 ! " " # # ! $ $ & & ' ' ( * % ¼ % ( * + , , + - - . . 0 0 2 2 ! " ¼ # ¼ ¼ # 8 ./4%3 3/,$%20!$490%./.3/,$%2-!3+$%&).%$.3-$ 0!#+!'%7%)'(4G *%$%#2%&%2%.#%-/$%3)'.# 0!#+!'%#/$%""!$ -!8 3%!4).'0,!.% # 51-85195-*A QDR RAMs and Quad Data Rate RAMs comprise a new family of products developed by Cypress, Hitachi, IDT, NEC, and Samsung technology. All product and company names mentioned in this document are the trademarks of their respective holders. Document #: 38-05615 Rev. *D Page 24 of 25 © Cypress Semiconductor Corporation, 2004-2007. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. CY7C1410AV18 CY7C1425AV18 CY7C1412AV18 CY7C1414AV18 Document History Page Document Title: CY7C1410AV18/CY7C1425AV18/CY7C1412AV18/CY7C1414AV18 36-Mbit QDR-II™ SRAM 2-Word Burst Architecture Document Number: 38-05615 REV. ECN No. Issue Date Orig. of Change Description of Change ** 247331 See ECN SYT New Data Sheet *A 326519 See ECN SYT Removed CY7C1425AV18 from the title Included 300 MHz Speed grade Replaced TBDs with their respective values for IDD and ISB1 Added Industrial temperature grade Replaced the TBDs on the Thermal Characteristics Table to ΘJA = 17.2°C/W and ΘJC = 3.2°C/W Replaced TBDs in the Capacitance Table to their respective values for the 165 FBGA Package Changed typo of bit # 47 to bit # 108 under the EXTEST OUTPUT BUS TRI-STATE on Page 16 Added Pb-free Product Information Updated the Ordering Information by Shading and Unshading MPNs according to availability *B 413953 See ECN NXR Converted from preliminary to final. Added CY7C1425AV18 part number to title. Removed 300-MHz speed Bin. Changed address of Cypress Semiconductor Corporation on Page# 1 from “3901 North First Street” to “198 Champion Court” Changed C, C Description in Feature Section and Pin Description. Added Power up sequence and Wave form on page# 19 Added foot notes # 13, 14, 15 on page# 19 Replaced Three-state with Tri-state. Changed the description of IX from Input Load Current to Input Leakage Current on page# 20 Modified the IDD and ISB values. Modified test condition in Footnote # 20 on page# 20 from VDDQ < VDD to VDDQ < VDD. Replaced Package Name column with Package Diagram in the Ordering Information table. Updated Ordering Information Table. *C 468029 See ECN NXR Modified the ZQ Definition from Alternately, this pin can be connected directly to VDD to Alternately, this pin can be connected directly to VDDQ. Included Maximum Ratings for Supply Voltage on VDDQ Relative to GND Changed the Maximum Ratings for DC Input Voltage from VDDQ to VDD. Changed tTH and tTL from 40 ns to 20 ns, changed tTMSS, tTDIS, tCS, tTMSH, tTDIH, tCH from 10 ns to 5 ns and changed tTDOV from 20 ns to 10 ns in TAP AC Switching Characteristics table Modified Power Up waveform Changed the Maximum rating of Ambient Temperature with Power Applied from –10°C to +85°C to –55°C to +125°C Added additional notes in the AC parameter section Changed the tSC and tHC value for 250 MHz from 0.5 ns to 0.35 ns, for 200 MHz from 0.6 ns to 0.4 ns, and for 167 MHz from 0.7 ns to 0.5 ns. Modified AC Switching Waveform. Corrected the typo In the AC Switching Characteristics Table. Updated the Ordering Information Table. *D 1274725 See ECN Document #: 38-05615 Rev. *D VKN/AESA Modified footnote# 30 Page 25 of 25