Low Power, 12.65 mW, 2.3 V to 5.5 V, Programmable Waveform Generator AD9833 Data Sheet FEATURES GENERAL DESCRIPTION Digitally programmable frequency and phase 12.65 mW power consumption at 3 V 0 MHz to 12.5 MHz output frequency range 28-bit resolution: 0.1 Hz at 25 MHz reference clock Sinusoidal, triangular, and square wave outputs 2.3 V to 5.5 V power supply No external components required 3-wire SPI interface Extended temperature range: −40°C to +105°C Power-down option 10-lead MSOP package Qualified for automotive applications The AD9833 is a low power, programmable waveform generator capable of producing sine, triangular, and square wave outputs. Waveform generation is required in various types of sensing, actuation, and time domain reflectometry (TDR) applications. The output frequency and phase are software programmable, allowing easy tuning. No external components are needed. The frequency registers are 28 bits wide: with a 25 MHz clock rate, resolution of 0.1 Hz can be achieved; with a 1 MHz clock rate, the AD9833 can be tuned to 0.004 Hz resolution. The AD9833 is written to via a 3-wire serial interface. This serial interface operates at clock rates up to 40 MHz and is compatible with DSP and microcontroller standards. The device operates with a power supply from 2.3 V to 5.5 V. APPLICATIONS The AD9833 has a power-down function (SLEEP). This function allows sections of the device that are not being used to be powered down, thus minimizing the current consumption of the part. For example, the DAC can be powered down when a clock output is being generated. Frequency stimulus/waveform generation Liquid and gas flow measurement Sensory applications: proximity, motion, and defect detection Line loss/attenuation Test and medical equipment Sweep/clock generators Time domain reflectometry (TDR) applications The AD9833 is available in a 10-lead MSOP package. FUNCTIONAL BLOCK DIAGRAM DGND AGND VDD CAP/2.5V ON-BOARD REFERENCE REGULATOR MCLK AVDD/ DVDD FULL-SCALE CONTROL 2.5V FREQ0 REG PHASE ACCUMULATOR (28-BIT) MUX FREQ1 REG 12 SIN ROM COMP 10-BIT DAC MUX MSB PHASE0 REG PHASE1 REG MUX DIVIDE BY 2 R 200Ω SERIAL INTERFACE AND CONTROL LOGIC SCLK AD9833 02704-001 FSYNC VOUT MUX CONTROL REGISTER SDATA Figure 1. Rev. E Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2003–2012 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com AD9833 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Control Register ......................................................................... 13 Applications ....................................................................................... 1 Frequency and Phase Registers ................................................ 15 General Description ......................................................................... 1 Reset Function ............................................................................ 16 Functional Block Diagram .............................................................. 1 Sleep Function ............................................................................ 16 Revision History ............................................................................... 2 VOUT Pin ................................................................................... 16 Specifications..................................................................................... 3 Applications Information .............................................................. 17 Timing Characteristics ................................................................ 4 Grounding and Layout .............................................................. 17 Absolute Maximum Ratings ............................................................ 5 Interfacing to Microprocessors ..................................................... 20 ESD Caution .................................................................................. 5 AD9833 to 68HC11/68L11 Interface ....................................... 20 Pin Configuration and Function Descriptions ............................. 6 AD9833 to 80C51/80L51 Interface .......................................... 20 Typical Performance Characteristics ............................................. 7 AD9833 to DSP56002 Interface ............................................... 20 Terminology .................................................................................... 10 Evaluation Board ............................................................................ 21 Theory of Operation ...................................................................... 11 System Demonstration Platform .............................................. 21 Circuit Description ......................................................................... 12 AD9833 to SPORT Interface ..................................................... 21 Numerically Controlled Oscillator Plus Phase Modulator ... 12 Evaluation Kit ............................................................................. 21 Sin ROM ...................................................................................... 12 Crystal Oscillator vs. External Clock ....................................... 21 Digital-to-Analog Converter (DAC) ....................................... 12 Power Supply............................................................................... 21 Regulator...................................................................................... 12 Evaluation Board Schematics ................................................... 22 Functional Description .................................................................. 13 Evaluation Board Layout ........................................................... 23 Serial Interface ............................................................................ 13 Outline Dimensions ....................................................................... 24 Powering Up the AD9833 ......................................................... 13 Ordering Guide .......................................................................... 24 Latency Period ............................................................................ 13 Automotive Products ................................................................. 24 REVISION HISTORY 9/12—Rev. D to Rev. E Changed Input Current, IINH/IINL from 10 mA to 10 µA.............. 3 4/11—Rev. C to Rev. D Change to Figure 13 ......................................................................... 8 Changes to Table 9 .......................................................................... 15 Deleted AD9833 to ADSP-2101/ADSP-2103 Interface Section .............................................................................................. 20 Changes to Evaluation Board Section .......................................... 21 Added System Demonstration Platform Section, AD9833 to SPORT Interface Section, and Evaluation Kit Section .......... 21 Changes to Crystal Oscillator vs. External Clock Section and Power Supply Section ............................................................. 21 Added Figure 32 and Figure 33; Renumbered Figures Sequentially ..................................................................................... 21 Deleted Prototyping Area Section and Figure 33 ....................... 22 Added Evaluation Board Schematics Section, Figure 34, and Figure 35 ................................................................................... 22 Deleted Table 16.............................................................................. 23 Added Evaluation Board Layout Section, Figure 36, Figure 37, and Figure 38 ................................................................ 23 Changes to Ordering Guide .......................................................... 24 9/10—Rev. B to Rev. C Changed 20 mW to 12.65 mW in Data Sheet Title and Features List ................................................................................1 Changes to Figure 6 Caption and Figure 7.....................................7 6/10—Rev. A to Rev. B Changes to Features Section ............................................................1 Changes to Serial Interface Section.............................................. 13 Changes to VOUT Pin Section ..................................................... 16 Changes to Grounding and Layout Section ................................ 17 Updated Outline Dimensions ....................................................... 24 Changes to Ordering Guide .......................................................... 24 Added Automotive Products Section .......................................... 24 6/03—Rev. 0 to Rev. A Updated Ordering Guide .................................................................4 Rev. E | Page 2 of 24 Data Sheet AD9833 SPECIFICATIONS VDD = 2.3 V to 5.5 V, AGND = DGND = 0 V, TA = TMIN to TMAX, RSET = 6.8 kΩ for VOUT, unless otherwise noted. Table 1. Parameter 1 SIGNAL DAC SPECIFICATIONS Resolution Update Rate VOUT Maximum VOUT Minimum VOUT Temperature Coefficient DC Accuracy Integral Nonlinearity Differential Nonlinearity DDS SPECIFICATIONS (SFDR) Dynamic Specifications Signal-to-Noise Ratio (SNR) Total Harmonic Distortion (THD) Spurious-Free Dynamic Range (SFDR) Wideband (0 to Nyquist) Narrow-Band (±200 kHz) Clock Feedthrough Wake-Up Time LOGIC INPUTS Input High Voltage, VINH Min Typ Max 10 55 0.65 38 200 ±1.0 ±0.5 LSB LSB 60 −66 dB dBc fMCLK = 25 MHz, fOUT = fMCLK/4096 fMCLK = 25 MHz, fOUT = fMCLK/4096 −60 −78 −60 1 dBc dBc dBc ms fMCLK = 25 MHz, fOUT = fMCLK/50 fMCLK = 25 MHz, fOUT = fMCLK/50 2.3 V to 2.7 V power supply 2.7 V to 3.6 V power supply 4.5 V to 5.5 V power supply 2.3 V to 2.7 V power supply 2.7 V to 3.6 V power supply 4.5 V to 5.5 V power supply 3 V V V V V V µA pF −56 1.7 2.0 2.8 0.5 0.7 0.8 10 Input Current, IINH/IINL Input Capacitance, CIN POWER SUPPLIES VDD IDD Low Power Sleep Mode Test Conditions/Comments Bits MSPS V mV ppm/°C 25 Input Low Voltage, VINL fMCLK = 25 MHz, fOUT = fMCLK/4096 2.3 5.5 5.5 4.5 0.5 V mA mA IDD code dependent; see Figure 7 DAC powered down, MCLK running Operating temperature range is −40°C to +105°C; typical specifications are at 25°C. 100nF VDD 10nF CAP/2.5V REGULATOR COMP 12 SIN ROM VOUT 10-BIT DAC 20pF AD9833 02704-002 1 Unit Figure 2. Test Circuit Used to Test Specifications Rev. E | Page 3 of 24 AD9833 Data Sheet TIMING CHARACTERISTICS VDD = 2.3 V to 5.5 V, AGND = DGND = 0 V, unless otherwise noted. 1 Table 2. Parameter t1 t2 t3 t4 t5 t6 t7 t8 min t8 max t9 t10 t11 1 Limit at TMIN to TMAX 40 16 16 25 10 10 5 10 t4 − 5 5 3 5 Unit ns min ns min ns min ns min ns min ns min ns min ns min ns max ns min ns min ns min Description MCLK period MCLK high duration MCLK low duration SCLK period SCLK high duration SCLK low duration FSYNC to SCLK falling edge setup time FSYNC to SCLK hold time Data setup time Data hold time SCLK high to FSYNC falling edge setup time Guaranteed by design, not production tested. Timing Diagrams t1 02704-003 MCLK t2 t3 Figure 3. Master Clock t5 t11 t4 SCLK t7 t6 t8 FSYNC t10 SDATA D15 D14 D2 D1 Figure 4. Serial Timing Rev. E | Page 4 of 24 D0 D1 5 D14 02704-004 t9 Data Sheet AD9833 ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted. Table 3. Parameter VDD to AGND VDD to DGND AGND to DGND CAP/2.5V Digital I/O Voltage to DGND Analog I/O Voltage to AGND Operating Temperature Range Industrial (B Version) Storage Temperature Range Maximum Junction Temperature MSOP Package θJA Thermal Impedance θJC Thermal Impedance Lead Temperature, Soldering (10 sec) IR Reflow, Peak Temperature Rating −0.3 V to +6 V −0.3 V to +6 V −0.3 V to +0.3 V 2.75 V −0.3 V to VDD + 0.3 V −0.3 V to VDD + 0.3 V Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION −40°C to +105°C −65°C to +150°C 150°C 206°C/W 44°C/W 300°C 220°C Rev. E | Page 5 of 24 AD9833 Data Sheet 10 VOUT AD9833 9 AGND TOP VIEW (Not to Scale) 8 FSYNC COMP 1 VDD 2 CAP/2.5V 3 DGND 4 MCLK 5 7 SCLK 6 SDATA 02704-005 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS Figure 5. Pin Configuration Table 4. Pin Function Descriptions Pin No. 1 2 Mnemonic COMP VDD 3 CAP/2.5V 4 5 DGND MCLK 6 7 8 SDATA SCLK FSYNC 9 10 AGND VOUT Description DAC Bias Pin. This pin is used for decoupling the DAC bias voltage. Positive Power Supply for the Analog and Digital Interface Sections. The on-board 2.5 V regulator is also supplied from VDD. VDD can have a value from 2.3 V to 5.5 V. A 0.1 µF and a 10 µF decoupling capacitor should be connected between VDD and AGND. The digital circuitry operates from a 2.5 V power supply. This 2.5 V is generated from VDD using an on-board regulator when VDD exceeds 2.7 V. The regulator requires a decoupling capacitor of 100 nF typical, which is connected from CAP/2.5V to DGND. If VDD is less than or equal to 2.7 V, CAP/2.5V should be tied directly to VDD. Digital Ground. Digital Clock Input. DDS output frequencies are expressed as a binary fraction of the frequency of MCLK. The output frequency accuracy and phase noise are determined by this clock. Serial Data Input. The 16-bit serial data-word is applied to this input. Serial Clock Input. Data is clocked into the AD9833 on each falling edge of SCLK. Active Low Control Input. FSYNC is the frame synchronization signal for the input data. When FSYNC is taken low, the internal logic is informed that a new word is being loaded into the device. Analog Ground. Voltage Output. The analog and digital output from the AD9833 is available at this pin. An external load resistor is not required because the device has a 200 Ω resistor on board. Rev. E | Page 6 of 24 Data Sheet AD9833 TYPICAL PERFORMANCE CHARACTERISTICS –40 5.5 VDD = 3V TA = 25°C TA = 25°C –45 5.0 VDD = 5V SFDR (dBc) –50 VDD = 3V 4.0 MCLK/7 –55 –60 3.5 MCLK/50 –65 0 5 10 15 MCLK FREQUENCY (MHz) 20 –70 02704-006 3.0 25 5 7 Figure 6. Typical Current Consumption (IDD) vs. MCLK Frequency for fOUT = MCLK/10 6 9 11 13 15 17 19 MCLK FREQUENCY (MHz) 21 23 25 02704-009 IDD (mA) 4.5 Figure 9. Wideband SFDR vs. MCLK Frequency 0 VDD = 5V VDD = 3V –10 VDD = 3V TA = 25°C 5 –20 –30 SFDR (dB) IDD (mA) 4 3 fMCLK = 10MHz –40 fMCLK = 18MHz fMCLK = 1MHz –50 –60 2 –70 1 1k 10k 100k 1M 10M fOUT (Hz) –90 0.001 02704-007 10 100 –40 –45 –70 –50 SNR (dB) –65 –75 MCLK/7 MCLK/50 –60 –85 –65 –90 5 10 15 MCLK FREQUENCY (MHz) 20 25 VDD = 3V TA = 25°C fOUT = MCLK/4096 –55 –80 –70 02704-008 SFDR (dBc) 1 Figure 10. Wideband SFDR vs. fOUT/fMCLK for Various MCLK Frequencies VDD = 3V TA = 25°C 0 0.1 fOUT/fMCLK Figure 7. Typical IDD vs. fOUT for fMCLK = 25 MHz –60 0.01 1.0 Figure 8. Narrow-Band SFDR vs. MCLK Frequency 5.0 10.0 MCLK FREQUENCY (MHz) 12.5 Figure 11. SNR vs. MCLK Frequency Rev. E | Page 7 of 24 25.0 02704-011 0 100 02704-010 fMCLK = 25MHz –80 AD9833 Data Sheet 1000 0 950 –10 –20 900 VDD = 2.3V –30 750 VDD = 5.5V 700 –40 –50 –60 650 –70 600 –80 550 –90 500 –40 25 TEMPERATURE (°C) 105 –100 Figure 12. Wake-Up Time vs. Temperature 0 RWB 1k VWB 300 FREQUENCY (Hz) 5M ST 50 SEC 02704-015 POWER (dB) 800 02704-012 WAKE-UP TIME (µs) 850 Figure 15. Power vs. Frequency, fMCLK = 10 MHz, fOUT = 1.43 MHz = fMCLK/7, Frequency Word = 0x2492492 0 1.250 –10 1.225 –20 UPPER RANGE –30 POWER (dB) VREF (V) 1.200 1.175 LOWER RANGE 1.150 –40 –50 –60 –70 –80 1.125 –90 105 –100 0 RWB 1k 0 0 –10 –20 –20 –30 –30 –40 –50 –60 –40 –50 –60 –70 –70 –80 –80 –90 –90 0 RWB 100 –100 VWB 30 FREQUENCY (Hz) 100k ST 100 SEC Figure 14. Power vs. Frequency, fMCLK = 10 MHz, fOUT = 2.4 kHz, Frequency Word = 0x000FBA9 0 RWB 100 VWB 30 FREQUENCY (Hz) 100k ST 100 SEC Figure 17. Power vs. Frequency, fMCLK = 25 MHz, fOUT = 6 kHz, Frequency Word = 0x000FBA9 Rev. E | Page 8 of 24 02704-017 POWER (dB) –10 02704-014 POWER (dB) 5M ST 50 SEC Figure 16. Power vs. Frequency, fMCLK = 10 MHz, fOUT = 3.33 MHz = fMCLK/3, Frequency Word = 0x5555555 Figure 13. VREF vs. Temperature –100 VWB 300 FREQUENCY (Hz) 02704-016 25 TEMPERATURE (°C) 02704-013 1.100 –40 AD9833 0 –10 –10 –20 –20 –30 –30 –40 –50 –60 –60 –70 –80 –80 –90 –90 –100 VWB 100 FREQUENCY (Hz) 1M ST 100 SEC –10 –10 –20 –20 –30 –30 POWER (dB) 0 –40 –50 –60 –50 –60 –70 –80 –80 –90 –90 –100 02704-019 –100 12.5M ST 100 SEC Figure 19. Power vs. Frequency, fMCLK = 25 MHz, fOUT = 600 kHz, Frequency Word = 0x0624DD3 –10 –20 –30 –40 –50 –60 –70 –80 VWB 300 FREQUENCY (Hz) 12.5M ST 100 SEC 02704-020 –90 0 RWB 1k 0 RWB 1k VWB 300 FREQUENCY (Hz) 12.5M ST 100 SEC Figure 22. Power vs. Frequency, fMCLK = 25 MHz, fOUT = 8.333 MHz = fMCLK/3, Frequency Word = 0x5555555 0 –100 12.5M ST 100 SEC –40 –70 VWB 300 FREQUENCY (Hz) VWB 300 FREQUENCY (Hz) Figure 21. Power vs. Frequency, fMCLK = 25 MHz, fOUT = 3.857 MHz = fMCLK/7, Frequency Word = 0x2492492 0 0 RWB 1k 0 RWB 1k 02704-022 0 RWB 300 Figure 18. Power vs. Frequency, fMCLK = 25 MHz, fOUT = 60 kHz, Frequency Word = 0x009D495 POWER (dB) –50 –70 –100 POWER (dB) –40 02704-021 POWER (dB) 0 02704-018 POWER (dB) Data Sheet Figure 20. Power vs. Frequency, fMCLK = 25 MHz, fOUT = 2.4 MHz, Frequency Word = 0x189374D Rev. E | Page 9 of 24 AD9833 Data Sheet TERMINOLOGY Integral Nonlinearity (INL) INL is the maximum deviation of any code from a straight line passing through the endpoints of the transfer function. The endpoints of the transfer function are zero scale, a point 0.5 LSB below the first code transition (000 … 00 to 000 … 01), and full scale, a point 0.5 LSB above the last code transition (111 … 10 to 111 … 11). The error is expressed in LSBs. Differential Nonlinearity (DNL) DNL is the difference between the measured and ideal 1 LSB change between two adjacent codes in the DAC. A specified DNL of ±1 LSB maximum ensures monotonicity. Output Compliance Output compliance refers to the maximum voltage that can be generated at the output of the DAC to meet the specifications. When voltages greater than that specified for the output compliance are generated, the AD9833 may not meet the specifications listed in the data sheet. Spurious-Free Dynamic Range (SFDR) Along with the frequency of interest, harmonics of the fundamental frequency and images of these frequencies are present at the output of a DDS device. SFDR refers to the largest spur or harmonic present in the band of interest. The wideband SFDR gives the magnitude of the largest spur or harmonic relative to the magnitude of the fundamental frequency in the zero to Nyquist bandwidth. The narrow-band SFDR gives the attenuation of the largest spur or harmonic in a bandwidth of ±200 kHz about the fundamental frequency. Total Harmonic Distortion (THD) THD is the ratio of the rms sum of harmonics to the rms value of the fundamental. For the AD9833, THD is defined as THD = 20 log V22 + V32 + V4 2 + V52 + V62 V1 where: V1 is the rms amplitude of the fundamental. V2, V3, V4, V5, and V6 are the rms amplitudes of the second through sixth harmonics. Signal-to-Noise Ratio (SNR) SNR is the ratio of the rms value of the measured output signal to the rms sum of all other spectral components below the Nyquist frequency. The value for SNR is expressed in decibels. Clock Feedthrough There is feedthrough from the MCLK input to the analog output. Clock feedthrough refers to the magnitude of the MCLK signal relative to the fundamental frequency in the output spectrum of the AD9833. Rev. E | Page 10 of 24 Data Sheet AD9833 THEORY OF OPERATION Sine waves are typically thought of in terms of their magnitude form: a(t) = sin(ωt). However, these sine waves are nonlinear and not easy to generate except through piecewise construction. On the other hand, the angular information is linear in nature. That is, the phase angle rotates through a fixed angle for each unit of time. The angular rate depends on the frequency of the signal by the traditional rate of ω = 2πf. MAGNITUDE Solving for ω, ω = ΔPhase/Δt = 2πf 6π f = ΔPhase × fMCLK∕2π 4π 2π The AD9833 builds the output based on this simple equation. A simple DDS chip can implement this equation with three major subcircuits: numerically controlled oscillator (NCO) and phase modulator, SIN ROM, and digital-to-analog converter (DAC). –1 2π PHASE 4π 6π 02704-023 2p ΔPhase = ωΔt Solving for f and substituting the reference clock frequency for the reference period (1/fMCLK = Δt) +1 0 Knowing that the phase of a sine wave is linear and given a reference interval (clock period), the phase rotation for that period can be determined. 0 Each subcircuit is described in the Circuit Description section. Figure 23. Sine Wave Rev. E | Page 11 of 24 AD9833 Data Sheet CIRCUIT DESCRIPTION The AD9833 is a fully integrated direct digital synthesis (DDS) chip. The chip requires one reference clock, one low precision resistor, and decoupling capacitors to provide digitally created sine waves up to 12.5 MHz. In addition to the generation of this RF signal, the chip is fully capable of a broad range of simple and complex modulation schemes. These modulation schemes are fully implemented in the digital domain, allowing accurate and simple realization of complex modulation algorithms using DSP techniques. The internal circuitry of the AD9833 consists of the following main sections: a numerically controlled oscillator (NCO), frequency and phase modulators, SIN ROM, a DAC, and a regulator. NUMERICALLY CONTROLLED OSCILLATOR PLUS PHASE MODULATOR This consists of two frequency select registers, a phase accumulator, two phase offset registers, and a phase offset adder. The main component of the NCO is a 28-bit phase accumulator. Continuous time signals have a phase range of 0 to 2π. Outside this range of numbers, the sinusoid functions repeat themselves in a periodic manner. The digital implementation is no different. The accumulator simply scales the range of phase numbers into a multibit digital word. The phase accumulator in the AD9833 is implemented with 28 bits. Therefore, in the AD9833, 2π = 228. Likewise, the ΔPhase term is scaled into this range of numbers: 0 < ΔPhase < 228 − 1 SIN ROM To make the output from the NCO useful, it must be converted from phase information into a sinusoidal value. Because phase information maps directly into amplitude, the SIN ROM uses the digital phase information as an address to a lookup table and converts the phase information into amplitude. Although the NCO contains a 28-bit phase accumulator, the output of the NCO is truncated to 12 bits. Using the full resolution of the phase accumulator is impractical and unnecessary, because this would require a lookup table of 228 entries. It is necessary only to have sufficient phase resolution such that the errors due to truncation are smaller than the resolution of the 10-bit DAC. This requires that the SIN ROM have two bits of phase resolution more than the 10-bit DAC. The SIN ROM is enabled using the mode bit (D1) in the control register (see Table 15). DIGITAL-TO-ANALOG CONVERTER (DAC) The AD9833 includes a high impedance, current source 10-bit DAC. The DAC receives the digital words from the SIN ROM and converts them into the corresponding analog voltages. The DAC is configured for single-ended operation. An external load resistor is not required because the device has a 200 Ω resistor on board. The DAC generates an output voltage of typically 0.6 V p-p. REGULATOR VDD provides the power supply required for the analog section and the digital section of the AD9833. This supply can have a value of 2.3 V to 5.5 V. With these substitutions, the previous equation becomes f = ΔPhase × fMCLK∕228 where 0 < ΔPhase < 228 − 1. The input to the phase accumulator can be selected from either the FREQ0 register or the FREQ1 register and is controlled by the FSELECT bit. NCOs inherently generate continuous phase signals, thus avoiding any output discontinuity when switching between frequencies. The internal digital section of the AD9833 is operated at 2.5 V. An on-board regulator steps down the voltage applied at VDD to 2.5 V. When the applied voltage at the VDD pin of the AD9833 is less than or equal to 2.7 V, the CAP/2.5V and VDD pins should be tied together, thus bypassing the on-board regulator. Following the NCO, a phase offset can be added to perform phase modulation using the 12-bit phase registers. The contents of one of these phase registers are added to the most significant bits of the NCO. The AD9833 has two phase registers; their resolution is 2π/4096. Rev. E | Page 12 of 24 Data Sheet AD9833 FUNCTIONAL DESCRIPTION SERIAL INTERFACE To avoid spurious DAC outputs during AD9833 initialization, the reset bit should be set to 1 until the part is ready to begin generating an output. A reset does not reset the phase, frequency, or control registers. These registers will contain invalid data and, therefore, should be set to known values by the user. The reset bit should then be set to 0 to begin generating an output. The data appears on the DAC output seven or eight MCLK cycles after the reset bit is set to 0. The AD9833 has a standard 3-wire serial interface that is compatible with the SPI, QSPI™, MICROWIRE®, and DSP interface standards. Data is loaded into the device as a 16-bit word under the control of a serial clock input, SCLK. The timing diagram for this operation is given in . The FSYNC input is a level-triggered input that acts as a frame synchronization and chip enable. Data can be transferred into the device only when FSYNC is low. To start the serial data transfer, FSYNC should be taken low, observing the minimum FSYNCto-SCLK falling edge setup time, t7. After FSYNC goes low, serial data is shifted into the input shift register of the device on the falling edges of SCLK for 16 clock pulses. FSYNC may be taken high after the 16th falling edge of SCLK, observing the minimum SCLK falling edge to FSYNC rising edge time, t8. Alternatively, FSYNC can be kept low for a multiple of 16 SCLK pulses and then brought high at the end of the data transfer. In this way, a continuous stream of 16-bit words can be loaded while FSYNC is held low; FSYNC goes high only after the 16th SCLK falling edge of the last word loaded. The SCLK can be continuous, or it can idle high or low between write operations. In either case, it must be high when FSYNC goes low (t11). For an example of how to program the AD9833, see the AN-1070 Application Note on the Analog Devices, Inc., website. POWERING UP THE AD9833 The flowchart in Figure 26 shows the operating routine for the AD9833. When the AD9833 is powered up, the part should be reset. This resets the appropriate internal registers to 0 to provide an analog output of midscale. LATENCY PERIOD A latency period is associated with each asynchronous write operation in the AD9833. If a selected frequency or phase register is loaded with a new word, there is a delay of seven or eight MCLK cycles before the analog output changes. The delay can be seven or eight cycles, depending on the position of the MCLK rising edge when the data is loaded into the destination register. CONTROL REGISTER The AD9833 contains a 16-bit control register that allows the user to configure the operation of the AD9833. All control bits other than the mode bit are sampled on the internal falling edge of MCLK. Table 6 describes the individual bits of the control register. The different functions and the various output options of the AD9833 are described in more detail in the Frequency and Phase Registers section. To inform the AD9833 that the contents of the control register will be altered, D15 and D14 must be set to 0, as shown in Table 5. Table 5. Control Register Bits D15 0 D14 0 D13 D0 Control Bits SLEEP12 SLEEP1 RESET AD9833 PHASE ACCUMULATOR (28-BIT) SIN ROM (LOW POWER) 10-BIT DAC 0 MUX 1 MODE + OPBITEN DIVIDE BY 2 1 MUX 0 DIGITAL OUTPUT (ENABLE) VOUT DIV2 DB15 DB14 0 0 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB13 DB12 DB11 DB10 DB9 DB8 DB7 0 MODE 0 B28 HLB FSELECT PSELECT 0 RESET SLEEP1 SLEEP12 OPBITEN 0 DIV2 Figure 24. Function of Control Bits Rev. E | Page 13 of 24 02704-024 OPBITEN AD9833 Data Sheet Table 6. Description of Bits in the Control Register Bit D13 Name B28 D12 HLB D11 D10 FSELECT PSELECT D9 D8 Reserved Reset D7 SLEEP1 D6 SLEEP12 D5 OPBITEN D4 D3 Reserved DIV2 D2 D1 Reserved Mode D0 Reserved Function Two write operations are required to load a complete word into either of the frequency registers. B28 = 1 allows a complete word to be loaded into a frequency register in two consecutive writes. The first write contains the 14 LSBs of the frequency word, and the next write contains the 14 MSBs. The first two bits of each 16-bit word define the frequency register to which the word is loaded and should, therefore, be the same for both of the consecutive writes. See Table 8 for the appropriate addresses. The write to the frequency register occurs after both words have been loaded; therefore, the register never holds an intermediate value. An example of a complete 28-bit write is shown in Table 9. When B28 = 0, the 28-bit frequency register operates as two 14-bit registers, one containing the 14 MSBs and the other containing the 14 LSBs. This means that the 14 MSBs of the frequency word can be altered independent of the 14 LSBs, and vice versa. To alter the 14 MSBs or the 14 LSBs, a single write is made to the appropriate frequency address. The control bit D12 (HLB) informs the AD9833 whether the bits to be altered are the 14 MSBs or 14 LSBs. This control bit allows the user to continuously load the MSBs or LSBs of a frequency register while ignoring the remaining 14 bits. This is useful if the complete 28-bit resolution is not required. HLB is used in conjunction with D13 (B28). This control bit indicates whether the 14 bits being loaded are being transferred to the 14 MSBs or 14 LSBs of the addressed frequency register. D13 (B28) must be set to 0 to be able to change the MSBs and LSBs of a frequency word separately. When D13 (B28) = 1, this control bit is ignored. HLB = 1 allows a write to the 14 MSBs of the addressed frequency register. HLB = 0 allows a write to the 14 LSBs of the addressed frequency register. The FSELECT bit defines whether the FREQ0 register or the FREQ1 register is used in the phase accumulator. The PSELECT bit defines whether the PHASE0 register or the PHASE1 register data is added to the output of the phase accumulator. This bit should be set to 0. Reset = 1 resets internal registers to 0, which corresponds to an analog output of midscale. Reset = 0 disables reset. This function is explained further in Table 13. When SLEEP1 = 1, the internal MCLK clock is disabled, and the DAC output remains at its present value because the NCO is no longer accumulating. When SLEEP1 = 0, MCLK is enabled. This function is explained further in Table 14. SLEEP12 = 1 powers down the on-chip DAC. This is useful when the AD9833 is used to output the MSB of the DAC data. SLEEP12 = 0 implies that the DAC is active. This function is explained further in Table 14. The function of this bit, in association with D1 (mode), is to control what is output at the VOUT pin. This is explained further in Table 15. When OPBITEN = 1, the output of the DAC is no longer available at the VOUT pin. Instead, the MSB (or MSB/2) of the DAC data is connected to the VOUT pin. This is useful as a coarse clock source. The DIV2 bit controls whether it is the MSB or MSB/2 that is output. When OPBITEN = 0, the DAC is connected to VOUT. The mode bit determines whether it is a sinusoidal or a ramp output that is available. This bit must be set to 0. DIV2 is used in association with D5 (OPBITEN). This is explained further in Table 15. When DIV2 = 1, the MSB of the DAC data is passed directly to the VOUT pin. When DIV2 = 0, the MSB/2 of the DAC data is output at the VOUT pin. This bit must be set to 0. This bit is used in association with OPBITEN (D5). The function of this bit is to control what is output at the VOUT pin when the on-chip DAC is connected to VOUT. This bit should be set to 0 if the control bit OPBITEN = 1. This is explained further in Table 15. When mode = 1, the SIN ROM is bypassed, resulting in a triangle output from the DAC. When mode = 0, the SIN ROM is used to convert the phase information into amplitude information, which results in a sinusoidal signal at the output. This bit must be set to 0. Rev. E | Page 14 of 24 Data Sheet AD9833 FREQUENCY AND PHASE REGISTERS Table 9. Writing 0xFFFC000 to the FREQ0 Register The AD9833 contains two frequency registers and two phase registers, which are described in Table 7. SDATA Input 0010 0000 0000 0000 Table 7. Frequency and Phase Registers Register FREQ0 Size 28 bits FREQ1 28 bits PHASE0 12 bits PHASE1 12 bits Description Frequency Register 0. When the FSELECT bit = 0, this register defines the output frequency as a fraction of the MCLK frequency. Frequency Register 1. When the FSELECT bit = 1, this register defines the output frequency as a fraction of the MCLK frequency. Phase Offset Register 0. When the PSELECT bit = 0, the contents of this register are added to the output of the phase accumulator. Phase Offset Register 1. When the PSELECT bit = 1, the contents of this register are added to the output of the phase accumulator. The analog output from the AD9833 is fMCLK/2 × FREQREG where FREQREG is the value loaded into the selected frequency register. This signal is phase shifted by 2π/4096 × PHASEREG The flowchart in Figure 28 shows the routine for writing to the frequency and phase registers of the AD9833. Writing to a Frequency Register When writing to a frequency register, Bit D15 and Bit D14 give the address of the frequency register. Table 8. Frequency Register Bits D13 MSB 14 FREQ0 REG bits MSB 14 FREQ1 REG bits In some applications, the user does not need to alter all 28 bits of the frequency register. With coarse tuning, only the 14 MSBs are altered, while with fine tuning, only the 14 LSBs are altered. By setting the B28 (D13) control bit to 0, the 28-bit frequency register operates as two, 14-bit registers, one containing the 14 MSBs and the other containing the 14 LSBs. This means that the 14 MSBs of the frequency word can be altered independent of the 14 LSBs, and vice versa. Bit HLB (D12) in the control register identifies which 14 bits are being altered. Examples of this are shown in Table 10 and Table 11. Table 10. Writing 0x3FFF to the 14 LSBs of the FREQ1 Register 1011 1111 1111 1111 Result of Input Word Control word write (D15, D14 = 00), B28 (D13) = 0; HLB (D12) = 0, that is, LSBs FREQ1 REG write (D15, D14 = 10), 14 LSBs = 0x3FFF Table 11. Writing 0x00FF to the 14 MSBs of the FREQ0 Register where PHASEREG is the value contained in the selected phase register. Consideration must be given to the relationship of the selected output frequency and the reference clock frequency to avoid unwanted output anomalies. D14 1 0 0111 1111 1111 1111 SDATA Input 0000 0000 0000 0000 28 D15 0 1 0100 0000 0000 0000 Result of Input Word Control word write (D15, D14 = 00), B28 (D13) = 1, HLB (D12) = X FREQ0 register write (D15, D14 = 01), 14 LSBs = 0x0000 FREQ0 register write (D15, D14 = 01), 14 MSBs = 0x3FFF D0 LSB LSB SDATA Input 0001 0000 0000 0000 0100 0000 1111 1111 Result of Input Word Control word write (D15, D14 = 00), B28 (D13) = 0, HLB (D12) = 1, that is, MSBs FREQ0 REG write (D15, D14 = 01), 14 MSBs = 0x00FF Writing to a Phase Register When writing to a phase register, Bit D15 and Bit D14 are set to 11. Bit D13 identifies which phase register is being loaded. Table 12. Phase Register Bits D15 1 1 If the user wants to change the entire contents of a frequency register, two consecutive writes to the same address must be performed because the frequency registers are 28 bits wide. The first write contains the 14 LSBs, and the second write contains the 14 MSBs. For this mode of operation, the B28 (D13) control bit should be set to 1. An example of a 28-bit write is shown in Table 9. Rev. E | Page 15 of 24 D14 1 1 D13 0 1 D12 X X D11 MSB 12 PHASE0 bits MSB 12 PHASE1 bits D0 LSB LSB AD9833 Data Sheet RESET FUNCTION VOUT PIN The reset function resets appropriate internal registers to 0 to provide an analog output of midscale. Reset does not reset the phase, frequency, or control registers. When the AD9833 is powered up, the part should be reset. To reset the AD9833, set the reset bit to 1. To take the part out of reset, set the bit to 0. A signal appears at the DAC to output eight MCLK cycles after reset is set to 0. The AD9833 offers a variety of outputs from the chip, all of which are available from the VOUT pin. The choice of outputs is the MSB of the DAC data, a sinusoidal output, or a triangle output. Table 13. Applying the Reset Function Result No reset applied Internal registers reset SLEEP FUNCTION Sections of the AD9833 that are not in use can be powered down to minimize power consumption. This is done using the sleep function. The parts of the chip that can be powered down are the internal clock and the DAC. The bits required for the sleep function are outlined in Table 14. Table 14. Applying the Sleep Function SLEEP1 Bit 0 0 1 1 SLEEP12 Bit 0 1 0 1 Result No power-down DAC powered down Internal clock disabled Both the DAC powered down and the internal clock disabled DAC Powered Down MSB of the DAC Data The MSB of the DAC data can be output from the AD9833. By setting the OPBITEN (D5) control bit to 1, the MSB of the DAC data is available at the VOUT pin. This is useful as a coarse clock source. This square wave can also be divided by 2 before being output. The DIV2 (D3) bit in the control register controls the frequency of this output from the VOUT pin. Sinusoidal Output The SIN ROM is used to convert the phase information from the frequency and phase registers into amplitude information that results in a sinusoidal signal at the output. To have a sinusoidal output from the VOUT pin, set the mode (D1) bit to 0 and the OPBITEN (D5) bit to 0. Triangle Output The SIN ROM can be bypassed so that the truncated digital output from the NCO is sent to the DAC. In this case, the output is no longer sinusoidal. The DAC will produce a 10-bit linear triangular function. To have a triangle output from the VOUT pin, set the mode (D1) bit = 1. Note that the SLEEP12 bit must be 0 (that is, the DAC is enabled) when using this pin. This is useful when the AD9833 is used to output the MSB of the DAC data only. In this case, the DAC is not required; therefore, it can be powered down to reduce power consumption. Table 15. Outputs from the VOUT Pin Internal Clock Disabled When the internal clock of the AD9833 is disabled, the DAC output remains at its present value because the NCO is no longer accumulating. New frequency, phase, and control words can be written to the part when the SLEEP1 control bit is active. The synchronizing clock is still active, which means that the selected frequency and phase registers can also be changed using the control bits. Setting the SLEEP1 bit to 0 enables the MCLK. Any changes made to the registers while SLEEP1 is active will be seen at the output after a latency period. OPBITEN Bit 0 0 1 1 1 1 Mode Bit 0 1 0 0 1 DIV2 Bit X1 X1 0 1 X1 X = don’t care. VOUT MAX VOUT MIN 2π Figure 25. Triangle Output Rev. E | Page 16 of 24 4π 6π 02704-025 Reset Bit 0 1 The OPBITEN (D5) and mode (D1) bits in the control register are used to decide which output is available from the AD9833. VOUT Pin Sinusoid Triangle DAC data MSB/2 DAC data MSB Reserved Data Sheet AD9833 APPLICATIONS INFORMATION Because of the various output options available from the part, the AD9833 can be configured to suit a wide variety of applications. One of the areas where the AD9833 is suitable is in modulation applications. The part can be used to perform simple modulation, such as FSK. More complex modulation schemes, such as GMSK and QPSK, can also be implemented using the AD9833. In an FSK application, the two frequency registers of the AD9833 are loaded with different values. One frequency represents the space frequency, while the other represents the mark frequency. Using the FSELECT bit in the control register of the AD9833, the user can modulate the carrier frequency between the two values. The AD9833 has two phase registers, which enables the part to perform PSK. With phase-shift keying, the carrier frequency is phase shifted, the phase being altered by an amount that is related to the bit stream being input to the modulator. The AD9833 is also suitable for signal generator applications. Because the MSB of the DAC data is available at the VOUT pin, the device can be used to generate a square wave. With its low current consumption, the part is suitable for applications in which it can be used as a local oscillator. GROUNDING AND LAYOUT The printed circuit board (PCB) that houses the AD9833 should be designed so that the analog and digital sections are separated and confined to certain areas of the board. This facilitates the use of ground planes that can be separated easily. A minimum etch technique is generally best for ground planes because it gives the best shielding. Digital and analog ground planes should be joined in one place only. If the AD9833 is the only device requiring an AGND-to-DGND connection, then the ground planes should be connected at the AGND and DGND pins of the AD9833. If the AD9833 is in a system where multiple devices require AGNDto-DGND connections, the connection should be made at one point only, a star ground point that should be established as close as possible to the AD9833. Avoid running digital lines under the device as these couple noise onto the die. The analog ground plane should be allowed to run under the AD9833 to avoid noise coupling. The power supply lines to the AD9833 should use as large a track as possible to provide low impedance paths and reduce the effects of glitches on the power supply line. Fast switching signals, such as clocks, should be shielded with digital ground to avoid radiating noise to other sections of the board. Avoid crossover of digital and analog signals. Traces on opposite sides of the board should run at right angles to each other. This reduces the effects of feedthrough through the board. A microstrip technique is by far the best, but it is not always possible with a double-sided board. In this technique, the component side of the board is dedicated to ground planes, and signals are placed on the other side. Good decoupling is important. The AD9833 should have supply bypassing of 0.1 μF ceramic capacitors in parallel with 10 μF tantalum capacitors. To achieve the best performance from the decoupling capacitors, they should be placed as close as possible to the device, ideally right up against the device. Rev. E | Page 17 of 24 AD9833 Data Sheet DATA WRITE (SEE FIGURE 28) SELECT DATA SOURCES WAIT 7/8 MCLK CYCLES INITIALIZATION (SEE FIGURE 27 BELOW) DAC OUTPUT VOUT = VREF × 18 × RLOAD / RSET × (1 + (SIN (2π (FREQREG × fMCLK × t/228 + PHASEREG / 212)))) YES CHANGE PSELECT? CHANGE PHASE? NO YES CHANGE FSELECT? CHANGE PHASE REGISTER? CHANGE FREQUENCY? YES NO NO CHANGE FREQUENCY REGISTER? CHANGE DAC OUTPUT FROM SIN TO RAMP? YES NO CONTROL REGISTER WRITE (SEE TABLE 6) YES CHANGE OUTPUT TO A DIGITAL SIGNAL? 02704-026 YES NO NO Figure 26. Flowchart for AD9833 Initialization and Operation INITIALIZATION APPLY RESET (CONTROL REGISTER WRITE) RESET = 1 WRITE TO FREQUENCY AND PHASE REGISTERS FREQ0 REG = fOUT0/fMCLK × 228 FREQ1 REG = fOUT1/fMCLK × 228 PHASE0 AND PHASE1 REG = (PHASESHIFT × 212)/2π (SEE FIGURE 28) SET RESET = 0 SELECT FREQUENCY REGISTERS SELECT PHASE REGISTERS (CONTROL REGISTER WRITE) RESET BIT = 0 FSELECT = SELECTED FREQUENCY REGISTER PSELECT = SELECTED PHASE REGISTER Figure 27. Flowchart for Initialization Rev. E | Page 18 of 24 02704-027 YES YES Data Sheet AD9833 DATA WRITE WRITE A FULL 28-BIT WORD TO A FREQUENCY REGISTER? YES (CONTROL REGISTER WRITE) B28 (D13) = 1 NO WRITE 14MSBs OR LSBs TO A FREQUENCY REGISTER? NO WRITE TO PHASE REGISTER? YES YES (CONTROL REGISTER WRITE) B28 (D13) = 0 HLB (D12) = 0/1 (16-BIT WRITE) YES WRITE A 16-BIT WORD (SEE TABLE 9 FOR EXAMPLE) (SEE TABLE 10 AND TABLE 11 FOR EXAMPLES) WRITE ANOTHER FULL 28-BIT WORD TO A FREQUENCY REGISTER? WRITE 14MSBs OR LSBs TO A FREQUENCY REGISTER? NO YES NO Figure 28. Flowchart for Data Writes Rev. E | Page 19 of 24 WRITE TO ANOTHER PHASE REGISTER? NO YES 02704-028 WRITE TWO CONSECUTIVE 16-BIT WORDS D15, D14 = 11 D13 = 0/1 (CHOOSE THE PHASE REGISTER) D12 = X D11 ... D0 = PHASE DATA AD9833 Data Sheet INTERFACING TO MICROPROCESSORS AD9833 TO 68HC11/68L11 INTERFACE Figure 29 shows the serial interface between the AD9833 and the 68HC11/68L11 microcontroller. The microcontroller is configured as the master by setting the MSTR bit in the SPCR to 1. This setting provides a serial clock on SCK; the MOSI output drives the serial data line SDATA. Because the microcontroller does not have a dedicated frame sync pin, the FSYNC signal is derived from a port line (PC7). The setup conditions for correct operation of the interface are as follows: • • SCK idles high between write operations (CPOL = 0) Data is valid on the SCK falling edge (CPHA = 1) When data is being transmitted to the AD9833, the FSYNC line is taken low (PC7). Serial data from the 68HC11/68L11 is transmitted in 8-bit bytes with only eight falling clock edges occurring in the transmit cycle. Data is transmitted MSB first. To load data into the AD9833, PC7 is held low after the first eight bits are transferred, and a second serial write operation is performed to the AD9833. Only after the second eight bits are transferred should FSYNC be taken high again. AD9833 PC7 FSYNC MOSI SDATA SCLK Figure 29. 68HC11/68L11 to AD9833 Interface When data is to be transmitted to the AD9833, P3.3 is taken low. The 80C51/80L51 transmits data in 8-bit bytes, thus only eight falling SCLK edges occur in each cycle. To load the remaining eight bits to the AD9833, P3.3 is held low after the first eight bits are transmitted, and a second write operation is initiated to transmit the second byte of data. P3.3 is taken high following the completion of the second write operation. SCLK should idle high between the two write operations. The 80C51/80L51 outputs the serial data in a format that has the LSB first. The AD9833 accepts the MSB first (the four MSBs are the control information, the next four bits are the address, and the eight LSBs contain the data when writing to a destination register). Therefore, the transmit routine of the 80C51/80L51 must take this into account and rearrange the bits so that the MSB is output first. 80C51/80L51 AD9833 P3.3 FSYNC RxD SDATA TxD SCLK Figure 30. 80C51/80L51 to AD9833 Interface AD9833 TO DSP56002 INTERFACE 02704-030 SCK Figure 30 shows the serial interface between the AD9833 and the 80C51/80L51 microcontroller. The microcontroller is operated in Mode 0 so that TxD of the 80C51/80L51 drives SCLK of the AD9833, and RxD drives the serial data line SDATA. The FSYNC signal is derived from a bit programmable pin on the port (P3.3 is shown in Figure 30). Figure 31 shows the interface between the AD9833 and the DSP56002. The DSP56002 is configured for normal mode asynchronous operation with a gated internal clock (SYN = 0, GCK = 1, SCKD = 1). The frame sync pin is generated internally (SC2 = 1), the transfers are 16 bits wide (WL1 = 1, WL0 = 0), and the frame sync signal frames the 16 bits (FSL = 0). The frame sync signal is available on the SC2 pin, but it must be inverted before it is applied to the AD9833. The interface to the DSP56000/DSP56001 is similar to that of the DSP56002. DSP56002 AD9833 SC2 FSYNC STD SDATA SCK SCLK 02704-032 68HC11/68L11 AD9833 TO 80C51/80L51 INTERFACE 02704-031 The AD9833 has a standard serial interface that allows the part to interface directly with several microprocessors. The device uses an external serial clock to write the data or control information into the device. The serial clock can have a frequency of 40 MHz maximum. The serial clock can be continuous, or it can idle high or low between write operations. When data or control information is written to the AD9833, FSYNC is taken low and is held low until the 16 bits of data are written into the AD9833. The FSYNC signal frames the 16 bits of information that are loaded into the AD9833. Figure 31. DSP56002 to AD9833 Interface Rev. E | Page 20 of 24 Data Sheet AD9833 EVALUATION BOARD The AD9833 evaluation board allows designers to evaluate the high performance AD9833 DDS modulator with a minimum of effort. More information about the evaluation software is available on the software CD and on the AD9833 product page. SYSTEM DEMONSTRATION PLATFORM The system demonstration platform (SDP) is a hardware and software evaluation tool for use in conjunction with product evaluation boards. The SDP board is based on the Blackfin® ADSP-BF527 processor with USB connectivity to the PC through a USB 2.0 high speed port. For more information about the SDP board, see the SDP board product page. Note that the SDP board is sold separately from the AD9833 evaluation board. AD9833 TO SPORT INTERFACE 02704-035 The Analog Devices SDP board has a SPORT serial port that is used to control the serial inputs to the AD9833. The connections are shown in Figure 32. AD9833 SPORT_TSCLK SPORT_DTO Figure 33. AD9833 Evaluation Software Interface FSYNC CRYSTAL OSCILLATOR VS. EXTERNAL CLOCK SCLK The AD9833 can operate with master clocks up to 25 MHz. A 25 MHz oscillator is included on the evaluation board. This oscillator can be removed and, if required, an external CMOS clock can be connected to the part. Options for the general oscillator include the following: SDATA ADSP-BF527 02704-034 SPORT_TFS Figure 32. SDP to AD9833 Interface EVALUATION KIT The DDS evaluation kit includes a populated, tested AD9833 printed circuit board (PCB). The schematics of the evaluation board are shown in Figure 34 and Figure 35. The software provided in the evaluation kit allows the user to easily program the AD9833 (see Figure 33). The evaluation software runs on any IBM-compatible PC with Microsoft® Windows® software installed (including Windows 7). The software is compatible with both 32-bit and 64-bit operating systems. • • AEL 301-Series oscillators, AEL Crystals SG-310SCN oscillators, Epson Electronics POWER SUPPLY Power to the AD9833 evaluation board can be provided from the USB connector or externally through pin connections. The power leads should be twisted to reduce ground loops. Rev. E | Page 21 of 24 AD9833 Data Sheet 02704-036 EVALUATION BOARD SCHEMATICS 02704-037 Figure 34. Evaluation Board Schematic Figure 35. SDP Connector Schematic Rev. E | Page 22 of 24 Data Sheet AD9833 02704-038 02704-040 EVALUATION BOARD LAYOUT Figure 38. AD9833 Evaluation Board Solder Side 02704-039 Figure 36. AD9833 Evaluation Board Component Side Figure 37. AD9833 Evaluation Board Silkscreen Rev. E | Page 23 of 24 AD9833 Data Sheet OUTLINE DIMENSIONS 3.10 3.00 2.90 10 3.10 3.00 2.90 5.15 4.90 4.65 6 1 5 PIN 1 IDENTIFIER 0.50 BSC 0.95 0.85 0.75 15° MAX 1.10 MAX 0.30 0.15 6° 0° 0.23 0.13 0.70 0.55 0.40 COMPLIANT TO JEDEC STANDARDS MO-187-BA 091709-A 0.15 0.05 COPLANARITY 0.10 Figure 39. 10-Lead Mini Small Outline Package [MSOP] (RM-10) Dimensions shown in millimeters ORDERING GUIDE Model1, 2, 3 AD9833BRM AD9833BRM-REEL AD9833BRM-REEL7 AD9833BRMZ AD9833BRMZ-REEL AD9833BRMZ-REEL7 AD9833WBRMZ-REEL EVAL-AD9833SDZ 1 2 3 Temperature Range −40°C to +105°C −40°C to +105°C −40°C to +105°C −40°C to +105°C −40°C to +105°C −40°C to +105°C −40°C to +105°C Package Description 10-Lead MSOP 10-Lead MSOP 10-Lead MSOP 10-Lead MSOP 10-Lead MSOP 10-Lead MSOP 10-Lead MSOP Evaluation Board Package Option RM-10 RM-10 RM-10 RM-10 RM-10 RM-10 RM-10 Branding DJB DJB DJB D68 D68 D68 D68 Z = RoHS Compliant Part. W = Qualified for Automotive Applications. The evaluation board for the AD9833 requires the system demonstration platform (SDP) board, which is sold separately. AUTOMOTIVE PRODUCTS The AD9833WBRMZ-REEL model is available with controlled manufacturing to support the quality and reliability requirements of automotive applications. Note that this automotive model may have specifications that differ from the commercial models; therefore, designers should review the Specifications section of this data sheet carefully. Only the automotive grade product shown is available for use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for these models. ©2003–2012 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D02704-0-9/12(E) Rev. E | Page 24 of 24