ZM2BG96W Part Number: 3.5x2.7mm SURFACE MOUNT LED LAMP www.SunLED.com PRELIMINARY SPEC Features zSINGLE COLOR. zSUITABLE FOR ALL SMT ASSEMBLY AND SOLDER PROCESS. zAVAILABLE ON TAPE AND REEL. zIDEAL FOR BACKLIGHTING. zPACKAGE : 1500PCS / REEL. zMOISTURE SENSITIVITY LEVEL : LEVEL 4. zRoHS COMPLIANT. ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Notes: 1. All dimensions are in millimeters (inches). Operating Characteristics (TA=25°C) 2. Tolerance is ± 0.25(0.01") unless otherwise noted. 3. Specifications are subject to change without notice. Absolute Maximum Ratings (TA=25°C) M2BG (InGaN) Unit M2BG (InGaN) Unit Forward Voltage (Typ.) (IF=30mA) VF 3.3 V Reverse Voltage VR 5 V Forward Voltage (Max.) (IF=30mA) VF 3.8 V Forward Current IF 30 mA Reverse Current (Max.) (VR=5V) IR 10 uA Forward Current (Peak) 1/10 Duty Cycle 0.1ms Pulse Width iFS 100 mA Wavelength Of Peak Emission (Typ.) (IF=30mA) λP 525 nm Power Dissipation PT 114 mW Operating Temperature TA -40 ~ +85 Wavelength Of Dominant Emission (Typ.) (IF=30mA) λD 535 nm Tstg -40 ~ +85 Spectral Line Full Width At Half-Maximum (Typ.) (IF=30mA) Δλ 39 nm Capacitance (Typ.) (VF=0V, f=1MHz) C 65 pF °C Storage Temperature Electrostatic Discharge Threshold (HBM) Part Number ZM2BG96W Emitting Color Green Published Date : FEB 25, 2008 1000 Emitting Material InGaN V Luminous Intensity (IF=30mA) mcd Lens-color Water Clear Drawing No : SDSA6166 min. typ. 900 1790 V1 Wavelength nm λP Viewing Angle 2 θ 1/2 525 120° Checked : B.L.LIU P. 1/4 Part Number: ZM2BG96W 3.5x2.7mm SURFACE MOUNT LED LAMP www.SunLED.com M2BG Published Date : FEB 25, 2008 Drawing No : SDSA6166 V1 Checked : B.L.LIU P. 2/4 Part Number: ZM2BG96W 3.5x2.7mm SURFACE MOUNT LED LAMP www.SunLED.com Recommended Soldering Pattern (Units : mm; Tolerance: ±0.1) The device has a single mounting surface. The device must be mounted according to the specifications. Tape Specification (Units : mm) Remarks: If special sorting is required (e.g. binning based on forward voltage, Luminous intensity / luminous flux, or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous intensity / luminous flux: +/-15% 3. Forward Voltage: +/-0.1V Note: Accuracy may depend on the sorting parameters. Published Date : FEB 25, 2008 Drawing No : SDSA6166 V1 Checked : B.L.LIU P. 3/4 Part Number: 3.5x2.7mm SURFACE MOUNT LED LAMP www.SunLED.com PACKING & LABEL SPECIFICATIONS Published Date : FEB 25, 2008 ZM2BG96W Drawing No : SDSA6166 ZM2BG96W V1 Checked : B.L.LIU P. 4/4