ZMDKMYK45W-9 Part Number: 3.5x2.8mm SURFACE MOUNT LED LAMP www.SunLED.com Features z BOTH CHIPS CAN BE CONTROLLED SEPARATELY. z SUITABLE FOR ALL SMT ASSEMBLY AND SOLDER PROCESS. z AVAILABLE z IDEAL z PACKAGE: 1500PCS / REEL. z MOISTURE z RoHS ON TAPE AND REEL. FOR BACKLIGHTING. SENSITIVITY LEVEL : LEVEL 4. COMPLIANT. Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ± 0.2(0.008") unless otherwise noted. Operating Characteristics (TA=25°C) 3. Specifications are subject to change without notice. Absolute Maximum Ratings (TA=25°C) MDK MYK (InGaAlP) (InGaAlP) Unit Reverse Voltage VR 5 5 V Forward Current IF 30 30 mA Forward Current (Peak) 1/10 Duty Cycle 0.1ms Pulse Width iFS 185 175 mA Power Dissipation PT 75 75 mW Operating Temperature TA -40 ~ +85 Tstg -40 ~ +85 Storage Temperature Part Number ZMDKMYK45W-9 Emitting Color Emitting Material Red InGaAlP Yellow InGaAIP Published Date : FEB 25,2008 °C Forward Voltage (Typ.) (IF=20mA) VF 1.95 2.0 V Forward Voltage (Max.) (IF=20mA) VF 2.5 2.5 V Reverse Current (Max.) (VR=5V) IR 10 10 uA Wavelength Of Peak Emission (Typ.) (IF=20mA) λP 650 590 nm Wavelength Of Dominant Emission (Typ.) (IF=20mA) λD 635 590 nm Spectral Line Full Width At Half-Maximum (Typ.) (IF=20mA) Δλ 28 20 nm Capacitance (Typ.) (VF=0V, f=1MHz) C 35 20 pF Luminous Intensity (IF=20mA) mcd Lens-color Water Clear Drawing No : SDSA6174 MDK MYK Unit (InGaAlP) (InGaAlP) V1 Wavelength nm λP min. typ. 70 198 650 50 148 590 Checked : B.L.LIU Viewing Angle 2 θ 1/2 120° P.1/5 Part Number: ZMDKMYK45W-9 3.5x2.8mm SURFACE MOUNT LED LAMP www.SunLED.com MDK Published Date : FEB 25,2008 Drawing No : SDSA6174 V1 Checked : B.L.LIU P.2/5 Part Number: ZMDKMYK45W-9 3.5x2.8mm SURFACE MOUNT LED LAMP www.SunLED.com MYK Published Date : FEB 25,2008 Drawing No : SDSA6174 V1 Checked : B.L.LIU P.3/5 Part Number: ZMDKMYK45W-9 3.5x2.8mm SURFACE MOUNT LED LAMP www.SunLED.com Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) The device has a single mounting surface. The device must be mounted according to the specifications. Tape Specification (Units : mm) Remarks: If special sorting is required (e.g. binning based on forward voltage, Luminous intensity/ luminous flux, or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous intensity/ luminous flux: +/-15% 3. Forward Voltage: +/-0.1V Note: Accuracy may depend on the sorting parameters. Published Date : FEB 25,2008 Drawing No : SDSA6174 V1 Checked : B.L.LIU P.4/5 Part Number: 3.5x2.8mm SURFACE MOUNT LED LAMP www.SunLED.com PACKING & LABEL SPECIFICATIONS Published Date : FEB 25,2008 ZMDKMYK45W-9 Drawing No : SDSA6174 ZMDKMYK45W-9 V1 Checked : B.L.LIU P.5/5