KINGBRIGHT AM2520SYC03_05

SUBMINIATURE SOLID STATE LAMP
AM2520SYC03
SUPER BRIGHT YELLOW
Description
Features
SUBMINIA TURE PACKAGE.
The Super Bright Yellow device is made with DH InGaAlP
WIDE VIEWING ANGLE.
(on GaAs substrate) light emitting diode chip.
GULL WING LEAD.
LONG LIFE - SOLID STATE RELIABILITY.
LOW PACKAGE PROFILE.
PACKAGE : 1000PCS / REEL.
RoHS COMPLIANT.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the leads emerge from the package.
4. Specifications are subject to change without notice.
SPEC NO: DSAC2795
REV NO: V.4
DATE: APR/05/2005
PAGE: 1 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: Y.W.WANG
ERP: 1202000714
Selection Guide
Part No.
Dice
AM2520SYC03
Iv (mcd)
@ 20mA
Lens Type
SUPER BRIGHT YELLOW (InGaAlP)
WATER CLEAR
Viewing
Angle
Min.
Typ.
2 θ 1/2
110
700
20°
Note:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
Typ.
λpeak
Peak Wavelength
Super Bright Yellow
λD
Dominant Wavelength
∆λ1/2
Max.
Units
Test Conditions
590
nm
IF=20mA
Super Bright Yellow
588
nm
IF=20mA
Spectral Line Half-width
Super Bright Yellow
28
nm
IF=20mA
C
Capacitance
Super Bright Yellow
25
pF
VF=0V;f=1MHz
VF
Forward Voltage
Super Bright Yellow
2.0
2.5
V
IF=20mA
IR
Reverse Current
Super Bright Yellow
10
uA
VR = 5V
Absolute Maximum Ratings at TA=25°C
Parameter
Super Bright Yellow
Units
Power dissipation
125
mW
DC Forward Current
30
mA
Peak Forward Current [1]
150
mA
5
V
Reverse Voltage
Operating/Storage Temperature
-40°C To +85°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAC2795
REV NO: V.4
DATE: APR/05/2005
PAGE: 2 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: Y.W.WANG
ERP: 1202000714
Super Bright Yellow
AM2520SYC03
SPEC NO: DSAC2795
REV NO: V.4
DATE: APR/05/2005
PAGE: 3 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: Y.W.WANG
ERP: 1202000714
AM2520SYC03
Recommended Soldering Pattern
(Units : mm)
Tape Specifications
(Units : mm)
Remarks:
If special sorting is required (e.g. binning based on forward voltage, luminous intensity, or wavelength), the typical
accuracy of the sorting process is as follows:
1. Wavelength: +/-1nm
2. Luminous Intensity: +/-15%
3. Forward Voltage: +/-0.1V
Note: Accuracy may depend on the sorting parameters.
SPEC NO: DSAC2795
REV NO: V.4
DATE: APR/05/2005
PAGE: 4 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: Y.W.WANG
ERP: 1202000714