4.0x3.0mm RIGHT ANGLE SMD CHIP LED LAMP APEKA4030SYC Features SUPER BRIGHT YELLOW Description 4.0mmx3.0mm RIGHT ANGLE SMT LED, 2.65mm The Super Bright Yellow device is made with DH THICKNESS. InGaAlP (on GaAs substrate) light emitting diode chip. LOW POWER CONSUMPTION. WIDE VIEWING ANGLE. IDEAL FOR BACKLIGHT AND INDICATOR. PACKAGE :500PCS / REEL. RoHS COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2(0.008") unless otherwise noted. 3. Specifications are subject to change without notice. SPEC NO: DSAD1186 REV NO: V.2 DATE: JUN/30/2005 PAGE: 1 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1204000023 Selection Guide Part No. Dice APEKA4030SYC Iv (mcd) @ 20mA Lens Type SUPER BRIGHT YELLOW (InGaAlP) WATER CLEAR Viewing Angle Min. Typ. 2 θ 1/2 50 120 90° Note: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Super Bright Yellow λD Dominant Wavelength ∆λ1/2 Max. Units Test Conditions 590 nm IF=20mA Super Bright Yellow 588 nm IF=20mA Spectral Line Half-width Super Bright Yellow 28 nm IF=20mA C Capacitance Super Bright Yellow 25 pF VF=0V;f=1MHz VF Forward Voltage Super Bright Yellow 2.0 2.5 V IF=20mA IR Reverse Current Super Bright Yellow 10 uA VR = 5V Absolute Maximum Ratings at TA=25°C Parameter Super Bright Yellow Units Power dissipation 125 mW DC Forward Current 30 mA Peak Forward Current [1] 150 mA 5 V Reverse Voltage Operating/Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAD1186 REV NO: V.2 DATE: JUN/30/2005 PAGE: 2 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1204000023 Super Bright Yellow APEKA4030SYC SPEC NO: DSAD1186 REV NO: V.2 DATE: JUN/30/2005 PAGE: 3 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1204000023 APEKA4030SYC Recommended Soldering Pattern (Units : mm) Tape Specifications (Units : mm) SPEC NO: DSAD1186 REV NO: V.2 DATE: JUN/30/2005 PAGE: 4 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1204000023 PACKING & LABEL SPECIFICATIONS APEKA4030SYC Remarks: If special sorting is required (e.g. binning based on forward voltage, luminous intensity, or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous Intensity: +/-15% 3. Forward Voltage: +/-0.1V Note: Accuracy may depend on the sorting parameters. SPEC NO: DSAD1186 REV NO: V.2 DATE: JUN/30/2005 PAGE: 5 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1204000023