KINGBRIGHT AM2520SEC09

SUBMINIATURE SOLID STATE LAMP
AM2520SEC09
SUPER BRIGHT ORANGE
Features
OSUBMINIATURE PACKAGE.
Description
OWIDE VIEWING ANGLE.
The Super Bright Orange device is made with DH
OZ-BEND LEAD.
InGaAlP (on GaAs substrate) light emitting diode chip.
OLONG LIFE - SOLID STATE RELIABILITY.
OLOW PACKAGE PROFILE.
OPACKAGE : 1000PCS / REEL.
ORoHS COMPLIANT.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the lead emerge from the package.
4. Specifications are subject to change without notice.
SPEC NO: DSAD1284
REV NO: V.3
DATE: APR/O6/2005
PAGE: 1 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: S.H.CHEN
ERP:1202000610
Selection Guide
Part No.
Dice
AM2520SEC09
Iv (mcd)
@ 20mA
Lens Type
SUPER BRIGHT ORANGE (InGaAlP)
WATER CLEAR
Viewing
Angle
Min.
Typ.
2 θ 1/2
480
1300
20°
Note:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
λpeak
Peak Wavelength
Super Bright Orange
λD
Dominant Wavelength
∆λ1/2
Typ.
Max.
Units
Test Conditions
610
nm
IF=20mA
Super Bright Orange
601
nm
IF=20mA
Spectral Line Half-width
Super Bright Orange
29
nm
IF=20mA
C
Capacitance
Super Bright Orange
30
pF
VF=0V;f=1MHz
VF
Forward Voltage
Super Bright Orange
2.0
2.5
V
IF=20mA
IR
Reverse Current
Super Bright Orange
10
uA
VR = 5V
Absolute Maximum Ratings at TA=25°C
Parameter
Super Bright Orange
Units
Power dissipation
75
mW
DC Forward Current
30
mA
Peak Forward Current [1]
195
mA
5
V
Reverse Voltage
-40°C To +85°C
Operating/Storage Temperature
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAD1284
REV NO: V.3
DATE: APR/O6/2005
PAGE: 2 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: S.H.CHEN
ERP:1202000610
Super Bright Orange
AM2520SEC09
SPEC NO: DSAD1284
REV NO: V.3
DATE: APR/O6/2005
PAGE: 3 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: S.H.CHEN
ERP:1202000610
AM2520SEC09
Recommended Soldering Pattern
(Units : mm)
Tape Specifications
(Units : mm)
Remarks:
If special sorting is required (e.g. binning based on forward voltage, luminous intensity, or wavelength),
the typical accuracy of the sorting process is as follows:
1. Wavelength: +/-1nm
2. Luminous Intensity: +/-15%
3. Forward Voltage: +/-0.1V
Note: Accuracy may depend on the sorting parameters.
SPEC NO: DSAD1284
REV NO: V.3
DATE: APR/O6/2005
PAGE: 4 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: S.H.CHEN
ERP:1202000610