Continuous Rate 12.3 Mb/s to 675 Mb/s Clock and Data Recovery IC ADN2816 Preliminary Technical Data FEATURES PRODUCT DESCRIPTION Serial data input: 12.3 Mb/s to 675 Mb/s Exceeds SONET requirements for jitter transfer/ generation/tolerance Patented clock recovery architecture No reference clock required Loss of lock indicator I2C™ interface to access optional features Single-supply operation: 3.3 V Low power: 300 mW typical 5 mm × 5 mm 32-lead LFCSP, Pb Free The ADN2816 provides the receiver functions of quantization and clock and data recovery for continuous data rates from 12.3 Mb/s to 675 Mb/s. The ADN2816 automatically locks to all data rates without the need for an external reference clock or programming. All SONET jitter requirements are met, including jitter transfer, jitter generation, and jitter tolerance. All specifications are quoted for −40°C to +85°C ambient temperature, unless otherwise noted. The ADN2816 is available in a compact 5 mm × 5 mm 32-lead chip scale package. APPLICATIONS SONET OC-1/3/12 and all associated FEC rates Fibre Channel, ESCON, Fast Ethernet, SDI, etc. WDM transponders Regenerators/repeaters Test equipment Broadband cross-connects and routers FUNCTIONAL BLOCK DIAGRAM REFCLKP/N (OPTIONAL) LOL CF1 CF2 FREQUENCY DETECT LOOP FILTER PHASE DETECT LOOP FILTER VCC VEE PIN NIN BUFFER PHASE SHIFTER VCO VREF DATA RE-TIMING DATAOUTP/N CLKOUTP/N DRVCC DRVEE DVCC DVEE 04948-0-001 2 2 Figure 1. Rev. PrA Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.326.8703 © 2004 Analog Devices, Inc. All rights reserved. ADN2816 Preliminary Technical Data TABLE OF CONTENTS Specifications..................................................................................... 3 Theory of Operation ...................................................................... 13 Jitter Specifications....................................................................... 4 Functional Description.................................................................. 15 Output and Timing Specifications ............................................. 5 Frequency Acquisition............................................................... 15 Absolute Maximum Ratings............................................................ 6 Input buffer ................................................................................. 15 Thermal Characteristics .............................................................. 6 Lock Detector Operation .......................................................... 15 ESD Caution.................................................................................. 6 Harmonic Detector .................................................................... 16 Timing Characteristics..................................................................... 7 Squelch Mode ............................................................................. 16 Pin Configuration and Function Descriptions............................. 8 I2C Interface ................................................................................ 16 Typical Performance Characteristics ............................................. 9 Reference Clock (Optional) ...................................................... 17 I2C Interface Timing and Internal Register Description........... 10 Applications Information .............................................................. 20 Jitter Specifications ......................................................................... 12 PCB Design Guidelines ............................................................. 20 Jitter Generation ......................................................................... 12 Coarse Data Rate Readback Look-Up Table............................... 23 Jitter Transfer............................................................................... 12 Outline Dimensions ....................................................................... 25 Jitter Tolerance ............................................................................ 12 Ordering Guide .......................................................................... 25 REVISION HISTORY 6/04—Revision PrA: Initial Version Rev. PrA | Page 2 of 27 Preliminary Technical Data ADN2816 SPECIFICATIONS TA = TMIN to TMAX, VCC = VMIN to VMAX, VEE = 0 V, CF = 0.47 µF, SLICEP = SLICEN = VEE, Input Data Pattern: PRBS 223 − 1, unless otherwise noted. Table 1. Parameter QUANTIZER—DC CHARACTERISTICS Input Voltage Range Peak-to-Peak Differential Input Input Common Mode Level QUANTIZER—AC CHARACTERISTICS Data Rate S11 Input Resistance Input Capacitance LOSS OF LOCK DETECT (LOL) VCO Frequency Error for LOL Assert VCO Frequency Error for LOL De-Assert LOL Response Time ACQUISITION TIME Lock to Data Mode Optional Lock to REFCLK Mode DATA RATE READBACK ACCURACY Coarse Readback Fine Readback Conditions Min @ PIN or NIN, dc-coupled PIN – NIN DC-coupled 1.8 0.2 2.3 Typ Max Unit 2.5 2.8 2.0 2.8 V V V 675 @ 2.5 GHz Differential 12.3 −15 100 0.65 Mb/s dB Ω pF With respect to nominal With respect to nominal 12.3 Mb/s OC-12 1000 250 4 1.0 ppm ppm ms µs OC-12 OC-3 OC-1 12.3 Mb/s 2.0 3.4 9.8 40.0 10.0 ms ms ms ms ms (See Table 13) In addition to REFCLK accuracy Data rate < 20 Mb/s Data rate > 20 Mb/s 10 % POWER SUPPLY VOLTAGE POWER SUPPLY CURRENT OPERATING TEMPERATURE RANGE 3.0 –40 Rev. PrA | Page 3 of 27 3.3 90 200 100 3.6 +85 ppm ppm V mA °C ADN2816 Preliminary Technical Data JITTER SPECIFICATIONS TA = TMIN to TMAX, VCC = VMIN to VMAX, VEE = 0 V, CF = 0.47 uF, SLICEP = SLICEN = VEE, Input Data Pattern: PRBS 223 − 1, unless otherwise noted. Table 2. Parameter PHASE-LOCKED LOOP CHARACTERISTICS Jitter Transfer BW Jitter Peaking Jitter Generation Conditions Min OC-12 OC-3 OC-12 OC-3 OC-12, 12 kHz to 5 MHz OC-3, 12 kHz to 1.3 MHz Jitter Tolerance 1 OC-12, 223 − 1 PRBS 30 Hz1 300 Hz1 25 kHz 250 kHz1 OC-3, 223 − 1 PRBS 30 Hz1 300 Hz1 6500 Hz 65 kHz Max Unit 71 23 0 0 0.001 0.01 0.001 0.01 108 35 0.03 0.03 0.002 0.019 0.002 0.011 kHz kHz dB dB UI rms UI p-p UI rms UI p-p 100 44 2.5 1.0 UI p-p UI p-p UI p-p UI p-p 50 24 3.5 1.0 UI p-p UI p-p UI p-p UI p-p Jitter tolerance of the ADN2816 at these jitter frequencies is better than what the test equipment is able to measure. Rev. PrA | Page 4 of 27 Typ Preliminary Technical Data ADN2816 OUTPUT AND TIMING SPECIFICATIONS Table 3. Parameter LVDS OUPUT CHARACTERISTICS (CLKOUTP/N, DATAOUTP/N) Single-Ended Output Swing Differential Output Swing Output Offset Voltage Output Impedance LVDS Ouputs Timing Rise Time Fall Time Setup Time Hold Time 2 I C INTERFACE DC CHARACTERISTICS Input High Voltage Input Low Voltage Input Current Output Low Voltage I2C INTERFACE TIMING SCK Clock Frequency SCK Pulse Width High SCK Pulse Width Low Start Condition Hold Time Start Condition Setup Time Data Setup Time Data Hold Time SCK/SDA Rise/Fall Time Stop Condition Setup Time Bus Free Time between a Stop and a Start REFCLK CHARACTERISTICS Input Voltage Range Minimum Differential Input Drive Reference Frequency Required Accuracy LVTTL DC INPUT CHARACTERISTICS Input High Voltage Input Low Voltage Input High Current Input Low Current LVTTL DC OUTPUT CHARACTERISTICS Output High Voltage Output Low Voltage 1 Conditions Min VSE (see Figure 3) VDIFF (see Figure 3) 250 500 1125 Differential 20% to 80% 80% to 20% TS (see Figure 2), OC12 TH (see Figure 2), OC12 LVCMOS VIH VIL VIN = 0.1 VCC or VIN = 0.9 VCC VOL, IOL = 3.0 mA (See Figure 9) Typ 1200 100 Max Unit 400 800 1275 mV mV mV Ω 100 100 800 800 ps ps ps ps 0.7 VCC 0.3 VCC +10.0 0.4 −10.0 400 tHIGH tLOW tHD;STA tSU;STA tSU;DAT tHD;DAT TR/TF tSU;STO tBUF Optional lock to REFCLK mode @ REFCLKP or REFCLKN VIL VIH 600 1300 600 600 100 300 20 + 0.1 Cb1 600 1300 300 0 VCC 100 12.3 200 100 VIH VIL IIH, VIN = 2.4 V IIL, VIN = 0.4 V 2.0 VOH, IOH = −2.0 mA VOL, IOL = 2.0 mA 2.4 0.8 5 −5 Cb = total capacitance of one bus line in pF. If mixed with Hs-mode devices, faster fall-times are allowed. Rev. PrA | Page 5 of 27 0.4 V V µA V kHz ns ns ns ns ns ns ns ns ns V V mV p-p MHz ppm V V µA µA V V ADN2816 Preliminary Technical Data ABSOLUTE MAXIMUM RATINGS TA = TMIN to TMAX, VCC = VMIN to VMAX, VEE = 0 V, CF = 0.47 µF, SLICEP = SLICEN = VEE, unless otherwise noted. Table 4. Parameter Supply Voltage (VCC) Minimum Input Voltage (All Inputs) Maximum Input Voltage (All Inputs) Maximum Junction Temperature Storage Temperature Lead Temperature (Soldering 10 s) Rating 4.2 V VEE − 0.4 V VCC + 0.4 V 125°C −65°C to +150°C 300°C Stress above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. THERMAL CHARACTERISTICS Thermal Resistance 32-LFCSP, 4-layer board with exposed paddle soldered to VEE θJA = 28°C/W. ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. PrA | Page 6 of 27 Preliminary Technical Data ADN2816 TIMING CHARACTERISTICS CLKOUTP TH 04948-0-002 TS DATAOUTP/N Figure 2. Output Timing OUTP VCML VSE OUTN OUTP–OUTN VDIFF 04948-0-003 VSE 0V Figure 3. Single-Ended vs. Differential Output Specifications Rev. PrA | Page 7 of 27 ADN2816 Preliminary Technical Data 32 TEST2 31 VCC 30 VEE 29 DATAOUTP 28 DATAOUTN 27 SQUELCH 26 CLKOUTP 25 CLKOUTN PIN CONFIGURATION AND FUNCTION DESCRIPTIONS ADN2816* TOP VIEW (Not to Scale) 24 VCC 23 VEE 22 NC 21 SDA 20 SCK 19 SADDR5 18 VCC 17 VEE 04948-0-004 PIN 1 INDICATOR NC 9 REFCLKP 10 REFCLKN 11 VCC 12 VEE 13 CF2 14 CF1 15 LOL 16 TEST1 1 VCC 2 VREF 3 NIN 4 PIN 5 NC 6 NC 7 VEE 8 * THERE IS AN EXPOSED PAD ON THE BOTTOM OF THE PACKAGE THAT MUST BE CONNECTED TO GND. Figure 4. Pin Configuration Table 5. Pin Function Descriptions Pin No. 1 2 3 4 5 6 ,7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Exposed Pad Mnemonic TEST1 VCC VREF NIN PIN NC VEE NC REFCLKP REFCLKN VCC VEE CF2 CF1 LOL VEE VCC SADDR5 SCK SDA NC VEE VCC CLKOUTN CLKOUTP SQUELCH DATAOUTN DATAOUTP VEE VCC TEST2 Pad Type1 P AO AI AI P DI DI P P AO AO DO P P DI DI DI P P DO DO DI DO DO P P P Description Connect to VCC. Power for Limamp, LOS. Internal VREF Voltage. Decouple to GND with a 0.1 µF capacitor. Differential Data Input. CML. Differential Data Input. CML. No Connect GND for Limamp, LOS. No Connect Differential REFCLK Input. 12.3 MHz to 200 MHz. Differential REFCLK Input. 12.3 MHz to 200 MHz. VCO Power. VCO GND. Frequency Loop Capacitor. Frequency Loop Capacitor. Loss of Lock Indicator. LVTTL active high. FLL Detector GND. FLL Detector Power. Slave Address Bit 5. I2C Clock Input. I2C Data Input. No Connect Output Buffer, I2C GND. Output Buffer, I2C Power. Differential Recovered Clock Output. LVDS. Differential Recovered Clock Output. LVDS. Disable Clock and Data Outputs. Active high. LVTLL. Differential Recovered Data Output. LVDS. Differential Recovered Data Output. LVDS. Phase Detector, Phase Shifter GND. Phase Detector, Phase Shifter Power. Connect to VCC. Connect to GND 1 Type: P = power, AI = analog input, AO = analog output, DI = digital input, DO = digital output. Rev. PrA | Page 8 of 27 Preliminary Technical Data ADN2816 TYPICAL PERFORMANCE CHARACTERISTICS Rev. PrA | Page 9 of 27 ADN2816 Preliminary Technical Data I2C INTERFACE TIMING AND INTERNAL REGISTER DESCRIPTION R/W CTRL. SLAVE ADDRESS [6...0] A5 SET BY PIN 19 0 0 0 0 0 X 04948-0-007 1 MSB = 1 0 = WR 1 = RD S SLAVE ADDR, LSB = 0 (WR) A(S) SUB ADDR A(S) DATA A(S) DATA A(S) P 04948-0-008 Figure 5. Slave Address Configuration S SLAVE ADDR, LSB = 0 (WR) A(S) SUB ADDR A(S) S SLAVE ADDR, LSB = 1 (RD) A(S) DATA A(M) S = START BIT A(S) = ACKNOWLEDGE BY SLAVE DATA A(M) P P = STOP BIT A(M) = LACK OF ACKNOWLEDGE BY MASTER A(M) = ACKNOWLEDGE BY MASTER 04948-0-009 Figure 6. I2C Write Data Transfer Figure 7. I2C Read Data Transfer SDA SLAVE ADDRESS A6 SUB ADDRESS A5 STOP BIT DATA A7 A0 D7 D0 SCK S WR ACK ACK SLADDR[4...0] ACK SUB ADDR[6...1] DATA[6...1] Figure 8. I2C Data Transfer Timing tF tSU;DAT tHD;STA tBUF SDA tR tR tSU;STO tF tLOW tHIGH tHD;STA S tSU;STA tHD;DAT S Figure 9. I2C Port Timing Diagram Rev. PrA | Page 10 of 27 P S 04948-0-011 SCK P 04948-0-010 START BIT Preliminary Technical Data ADN2816 Table 6. Internal Register Map1 1 Reg Name FREQ0 FREQ1 FREQ2 RATE R/W R R R R Address 0x0 0x1 0x2 0x3 D7 D6 MSB MSB 0 MSB COARSE_RD[8] MSB MISC R 0x4 CTRLA W 0x8 CTRLB W 0x9 Config LOL Reset MISC[4] System reset 0 Reset MISC[2] CTRLC W 0x11 0 0 0 0 0 x D5 D4 D3 D2 D1 D0 LSB LSB LSB COARSE_RD[1] Datarate measure complete x COARSE_ RD[0] LSB Measure datarate Lock to reference 0 0 0 0 Squelch mode 0 Coarse datarate readback x Static LOL x FREF range LOL status Datarate/DIV_FREF ratio All writeable registers default to 0x00. Table 7. Miscellaneous Register, MISC D7 x D6 x D5 x Static LOL D4 0 = Waiting for next LOL 1 = Static LOL until reset LOL Status D3 0 = Locked 1 = Acquiring Datarate Measurement Complete D2 0 = Measuring datarate 1 = Measurement complete D1 x Coarse Rate Readback LSB D0 COARSE_RD[0] Table 8. Control Register, CTRLA1 FREF Range D7 D6 0 0 0 1 1 0 1 1 1 12.3 MHz to 25 MHz 25 MHz to 50 MHz 50 MHz to 100 MHz 100 MHz to 200 MHz Datarate/Div_FREF Ratio D5 D4 D3 D2 0 0 0 0 0 0 0 1 0 0 1 0 n 1 0 0 0 1 2 4 2n 256 Measure Datarate D1 Set to 1 to measure datarate Lock to Reference D0 0 = Lock to input data 1 = Lock to reference clock Where DIV_FREF is the divided down reference referred to the 12.3 MHz to 25 MHz band (see the Reference Clock (Optional) section). Table 9. Control Register, CTRLB Config LOL D7 0 = LOL pin normal operation 1 = LOL pin is static LOL Reset MISC[4] D6 Write a 1 followed by 0 to reset MISC[4] System Reset D5 Write a 1 followed by 0 to reset ADN2816 D4 Set to 0 Reset MISC[2] D3 Write a 1 followed by 0 to reset MISC[2] D2 Set to 0 D1 Set to 0 D0 Set to 0 Table 10. Control Register, CTRLC D7 Set to 0 D6 Set to 0 D5 Set to 0 D4 Set to 0 D3 Set to 0 D2 Set to 0 Rev. PrA | Page 11 of 27 Squelch Mode D1 0 = Squelch CLK and DATA 1 = Squelch CLK or DATA D0 Set to 0 ADN2816 Preliminary Technical Data JITTER SPECIFICATIONS JITTER GENERATION The jitter generation specification limits the amount of jitter that can be generated by the device with no jitter and wander applied at the input. For SONET devices, the jitter generated must be less than 0.01 UI rms, and must be less than 0.1 UIp-p. JITTER TRANSFER The jitter transfer function is the ratio of the jitter on the output signal to the jitter applied on the input signal versus the frequency. This parameter measures the limited amount of the jitter on an input signal that can be transferred to the output signal (see Figure 10). SLOPE = –20dB/DECADE 04948-0-015 ACCEPTABLE RANGE fC JITTER FREQUENCY (kHz) Figure 10. Jitter Transfer Curve JITTER TOLERANCE The jitter tolerance is defined as the peak-to-peak amplitude of the sinusoidal jitter applied on the input signal, which causes a 1 dB power penalty. This is a stress test intended to ensure that no additional penalty is incurred under the operating conditions (see Figure 11). 15.00 SLOPE = –20dB/DECADE 1.50 0.15 f0 f1 f2 f3 JITTER FREQUENCY (kHz) Figure 11. SONET Jitter Tolerance Mask Rev. PrA | Page 12 of 27 f4 04948-0-016 The following sections briefly summarize the specifications of jitter generation, transfer, and tolerance in accordance with the Telcordia document (GR-253-CORE, Issue 3, September 2000) for the optical interface at the equipment level and the ADN2816 performance with respect to those specifications. JITTER GAIN (dB) Jitter is the dynamic displacement of digital signal edges from their long-term average positions, measured in unit intervals (UI), where 1 UI = 1 bit period. Jitter on the input data can cause dynamic phase errors on the recovered clock sampling edge. Jitter on the recovered clock causes jitter on the retimed data. 0.1 INPUT JITTER AMPLITUDE (UI p-p) The ADN2816 CDR is designed to achieve the best bit-errorrate (BER) performance and exceeds the jitter transfer, generation, and tolerance specifications proposed for SONET/SDH equipment defined in the Telcordia Technologies specification. Preliminary Technical Data ADN2816 THEORY OF OPERATION Another view of the circuit is that the phase shifter implements the zero required for frequency compensation of a second-order phase-locked loop, and this zero is placed in the feedback path and, thus, does not appear in the closed-loop transfer function. Jitter peaking in a conventional second-order phase-locked loop is caused by the presence of this zero in the closed-loop transfer function. Because this circuit has no zero in the closed-loop transfer, jitter peaking is minimized. The delay- and phase-loops together simultaneously provide wide-band jitter accommodation and narrow-band jitter filtering. The linearized block diagram in Figure 12 shows that the jitter transfer function, Z(s)/X(s), is a second-order low-pass providing excellent filtering. Note that the jitter transfer has no zero, unlike an ordinary second-order phase-locked loop. This means that the main PLL loop has virtually zero jitter peaking (see Figure 13). This makes this circuit ideal for signal regenerator applications, where jitter peaking in a cascade of regenerators can contribute to hazardous jitter accumulation. The error transfer, e(s)/X(s), has the same high-pass form as an ordinary phase-locked loop. This transfer function is free to be optimized to give excellent wide-band jitter accommodation, because the jitter transfer function, Z(s)/X(s), provides the narrow-band jitter filtering. INPUT DATA e(s) X(s) d/sc o/s 1/n Z(s) RECOVERED CLOCK d = PHASE DETECTOR GAIN o = VCO GAIN c = LOOP INTEGRATOR psh = PHASE SHIFTER GAIN n = DIVIDE RATIO JITTER TRANSFER FUNCTION Z(s) 1 = cn n psh X(s) s2 +s +1 do o TRACKING ERROR TRANSFER FUNCTION 04948-0-017 e(s) s2 = d psh do X(s) + s2 + s c cn Figure 12. ADN2816 PLL/DLL Architecture JITTER PEAKING IN ORDINARY PLL ADN2816 Z(s) X(s) o n psh d psh c FREQUENCY (kHz) 04948-0-018 The delay- and phase-loops together track the phase of the input data signal. For example, when the clock lags input data, the phase detector drives the VCO to higher frequency, and also increases the delay through the phase shifter; both these actions serve to reduce the phase error between the clock and data. The faster clock picks up phase, while the delayed data loses phase. Because the loop filter is an integrator, the static phase error is driven to zero. psh JITTER GAIN (dB) The ADN2816 is a delay- and phase-locked loop circuit for clock recovery and data retiming from an NRZ encoded data stream. The phase of the input data signal is tracked by two separate feedback loops, which share a common control voltage. A high speed delay-locked loop path uses a voltage controlled phase shifter to track the high frequency components of input jitter. A separate phase control loop, comprised of the VCO, tracks the low frequency components of input jitter. The initial frequency of the VCO is set by yet a third loop, which compares the VCO frequency with the input data frequency and sets the coarse tuning voltage. The jitter tracking phase-locked loop controls the VCO by the fine-tuning control. Figure 13. ADN2816 Jitter Response vs. Conventional PLL The delay- and phase-loops contribute to overall jitter accommodation. At low frequencies of input jitter on the data signal, the integrator in the loop filter provides high gain to track large jitter amplitudes with small phase error. In this case, the VCO is frequency modulated and jitter is tracked as in an ordinary phase-locked loop. The amount of low frequency jitter that can be tracked is a function of the VCO tuning range. A wider tuning range gives larger accommodation of low frequency jitter. The internal loop control voltage remains small for small phase errors, so the phase shifter remains close to the center of its range and thus contributes little to the low frequency jitter accommodation. Rev. PrA | Page 13 of 27 ADN2816 Preliminary Technical Data At medium jitter frequencies, the gain and tuning range of the VCO are not large enough to track input jitter. In this case, the VCO control voltage becomes large and saturates, and the VCO frequency dwells at one extreme of its tuning range or the other. The size of the VCO tuning range, therefore, has only a small effect on the jitter accommodation. The delay-locked loop control voltage is now larger, and so the phase shifter takes on the burden of tracking the input jitter. The phase shifter range, in UI, can be seen as a broad plateau on the jitter tolerance curve. The phase shifter has a minimum range of 2 UI at all data rates. cannot be tolerated. In this region, the gain of the integrator determines the jitter accommodation. Because the gain of the loop integrator declines linearly with frequency, jitter accommodation is lower with higher jitter frequency. At the highest frequencies, the loop gain is very small, and little tuning of the phase shifter can be expected. In this case, jitter accommodation is determined by the eye opening of the input data, the static phase error, and the residual loop jitter generation. The jitter accommodation is roughly 0.5 UI in this region. The corner frequency between the declining slope and the flat region is the closed loop bandwidth of the delay-locked loop, which is roughly 1.0 MHz at 675 Mb/s. The gain of the loop integrator is small for high jitter frequencies, so that larger phase differences are needed to make the loop control voltage big enough to tune the range of the phase shifter. Large phase errors at high jitter frequencies Rev. PrA | Page 14 of 27 Preliminary Technical Data ADN2816 FUNCTIONAL DESCRIPTION FREQUENCY ACQUISITION Once LOL is de-asserted, the frequency-locked loop is turned off. The PLL/DLL pulls in the VCO frequency the rest of the way until the VCO frequency equals the data frequency. The frequency loop requires a single external capacitor between CF1 and CF2, Pins 14 and 15. A 0.47 µF ± 20%, X7R ceramic chip capacitor with < 10 nA leakage current is recommended. Leakage current of the capacitor can be calculated by dividing the maximum voltage across the 0.47 µF capacitor, ~3 V, by the insulation resistance of the capacitor. The insulation resistance of the 0.47 uF capacitor should be greater than 300 MΩ. INPUT BUFFER The input buffer has differential inputs (PIN/NIN), which are internally terminated with 50 Ω to an on-chip voltage reference (VREF = 2.5 V typically). The minimum differential input level required to achieve a BER of 10e-10 is 200mVpp. Figure 14. LOL 1 –1000 –250 0 250 1000 fVCO ERROR (ppm) 04948-0-020 The ADN2816 acquires frequency from the data over a range of data frequencies from 12.3 Mb/s to 675 Mb/s. The lock detector circuit compares the frequency of the VCO and the frequency of the incoming data. When these frequencies differ by more than 1000 ppm, LOL is asserted. This initiates a frequency acquisition cycle. The VCO frequency is reset to the bottom of its range, which is 12.3 MHz. The frequency detector then compares this VCO frequency and the incoming data frequency and increments the VCO frequency, if necessary. Initially, the VCO frequency is incremented in large steps to aid fast acquisition. As the VCO frequency approaches the data frequency, the step size is reduced until the VCO frequency is within 250 ppm of the data frequency, at which point LOL is de-asserted. Figure 14. Transfer Function of LOL LOL Detector Operation Using a Reference Clock In this mode, a reference clock is used as an acquisition aid to lock the ADN2816 VCO. Lock to reference mode is enabled by setting CTRLA[0] to 1. The user also needs to write to the CTRLA[7:6] and CTRLA[5:2] bits in order to set the reference frequency range and the divide ratio of the data rate with respect to the reference frequency. For more details, see the Reference Clock (Optional) section. In this mode, the lock detector monitors the difference in frequency between the divided down VCO and the divided down reference clock. The loss of lock signal, which appears on the LOL Pin 16, is deasserted when the VCO is within 250 ppm of the desired frequency. This enables the D/PLL, which pulls the VCO frequency in the remaining amount with respect to the input data and also acquires phase lock. Once locked, if the input frequency error exceeds 1000 ppm (0.1%), the loss of lock signal is re-asserted and control returns to the frequency loop, which re-acquires with respect to the reference clock. The LOL pin remains asserted until the VCO frequency is within 250 ppm of the desired frequency. This hysteresis is shown in Figure 14. Static LOL Mode LOCK DETECTOR OPERATION The lock detector on the ADN2816 has three modes of operation: normal mode, REFCLK mode, and static LOL mode. Normal Mode In normal mode, the ADN2816 is a continuous rate CDR that locks onto any data rate from 12.3 Mb/s to 675 Mb/s without the use of a reference clock as an acquisition aid. In this mode, the lock detector monitors the frequency difference between the VCO and the input data frequency, and de-asserts the loss of lock signal, which appears on LOL Pin 16, when the VCO is within 250 ppm of the data frequency. This enables the D/PLL, which pulls the VCO frequency in the remaining amount and also acquires phase lock. Once locked, if the input frequency error exceeds 1000 ppm (0.1%), the loss of lock signal is reasserted and control returns to the frequency loop, which begins a new frequency acquisition starting at the lowest point in the VCO operating range, 12.3 MHz. The LOL pin remains asserted until the VCO locks onto a valid input data stream to within 250 ppm frequency error. This hysteresis is shown in The ADN2816 implements a static LOL feature, which indicates if a loss of lock condition has ever occurred and remains asserted, even if the ADN2816 regains lock, until the static LOL bit is manually reset. The I2C register bit, MISC[4], is the static LOL bit. If there is ever an occurrence of a loss of lock condition, this bit is internally asserted to logic high. The MISC[4] bit remains high even after the ADN2816 has reacquired lock to a new data rate. This bit can be reset by writing a 1 followed by 0 to I2C Register Bit CTRLB[6]. Once reset, the MISC[4] bit remains de-asserted until another loss of lock condition occurs. Writing a 1 to I2C Register Bit CTRLB[7] causes the LOL pin, Pin 16, to become a static LOL indicator. In this mode, the LOL pin mirrors the contents of the MISC[4] bit and has the functionality described in the previous paragraph. The CTRLB[7] bit defaults to 0. In this mode, the LOL pin operates in the normal operating mode, that is, it is asserted only when Rev. PrA | Page 15 of 27 ADN2816 Preliminary Technical Data the ADN2816 is in acquisition mode and de-asserts when the ADN2816 has re-acquired lock. to a high state, the DATAOUT pins are squelched. When the squelch input is driven to a low state, the CLKOUT pins are squelched. This is especially useful in repeater applications, where the recovered clock may not be needed. HARMONIC DETECTOR I2C INTERFACE The ADN2816 provides a harmonic detector, which detects whether or not the input data has changed to a lower harmonic of the data rate that the VCO is currently locked onto. For example, if the input data instantaneously changes from OC-12, 622.08Mb/s, to an OC-3, 155.52 Mb/s bit stream, this could be perceived as a valid OC-12 bit stream, because the OC-3 data pattern is exactly 4× slower than the OC-12 pattern. So, if the change in data rate is instantaneous, a 101 pattern at OC-3 would be perceived by the ADN2816 as a 111100001111 pattern at OC-12. If the change to a lower harmonic is instantaneous, a typical CDR could remain locked at the higher data rate. The ADN2816 supports a 2-wire, I2C compatible, serial bus driving multiple peripherals. Two inputs, serial data (SDA) and serial clock (SCK), carry information between any devices connected to the bus. Each slave device is recognized by a unique address. The ADN2816 has two possible 7-bit slave addresses for both read and write operations. The MSB of the 7-bit slave address is factory programmed to 1. B5 of the slave address is set by Pin 19, SADDR5. Slave address bits [4:0] are defaulted to all 0s. The slave address consists of the 7 MSBs of an 8-bit word. The LSB of the word sets either a read or write operation (see Figure 5). Logic 1 corresponds to a read operation, while Logic 0 corresponds to a write operation. The ADN2816 implements a harmonic detector that automatically identifies whether or not the input data has switched to a lower harmonic of the data rate that the VCO is currently locked onto. When a harmonic is identified, the LOL pin is asserted and a new frequency acquisition is initiated. The ADN2816 automatically locks onto the new data rate, and the LOL pin is de-asserted. However, the harmonic detector does not detect higher harmonics of the data rate. If the input data rate switches to a higher harmonic of the data rate the VCO is currently locked onto, the VCO loses lock, the LOL pin is asserted, and a new frequency acquisition is initiated. The ADN2816 automatically locks onto the new data rate. The time to detect lock to harmonic is 16,384 × (Td/ρ) where: 1/Td is the new data rate. For example, if the data rate is switched from OC-12 to OC-3, then Td = 1/155.52 MHz. ρ is the data transition density. Most coding schemes seek to ensure that ρ = 0.5, for example, PRBS, 8B/10B. When the ADN2816 is placed in lock to reference mode, the harmonic detector is disabled. SQUELCH MODE Two squelch modes are available with the ADN2816. Squelch DATAOUT AND CLKOUT mode is selected when CTRLC[1] = 0 (default mode). In this mode, when the squelch input, Pin 27, is driven to a TTL high state, both the clock and data outputs are set to the zero state to suppress downstream processing. If the squelch function is not required, Pin 27 should be tied to VEE. Squelch DATAOUT OR CLKOUT mode is selected when CTRLC[1] is 1. In this mode, when the squelch input is driven To control the device on the bus, the following protocol must be followed. First, the master initiates a data transfer by establishing a start condition, defined by a high to low transition on SDA while SCK remains high. This indicates that an address/data stream follows. All peripherals respond to the start condition and shift the next eight bits (the 7-bit address and the R/W bit). The bits are transferred from MSB to LSB. The peripheral that recognizes the transmitted address responds by pulling the data line low during the ninth clock pulse. This is known as an acknowledge bit. All other devices withdraw from the bus at this point and maintain an idle condition. The idle condition is where the device monitors the SDA and SCK lines waiting for the start condition and correct transmitted address. The R/W bit determines the direction of the data. Logic 0 on the LSB of the first byte means that the master writes information to the peripheral. Logic 1 on the LSB of the first byte means that the master reads information from the peripheral. The ADN2816 acts as a standard slave device on the bus. The data on the SDA pin is 8 bits long supporting the 7-bit addresses plus the R/W bit. The ADN2816 has 8 subaddresses to enable the user-accessible internal registers (see Table 1 through Table 7). It, therefore, interprets the first byte as the device address and the second byte as the starting subaddress. Autoincrement mode is supported, allowing data to be read from or written to the starting subaddress and each subsequent address without manually addressing the subsequent subaddress. A data transfer is always terminated by a stop condition. The user can also access any unique subaddress register on a one-by-one basis without updating all registers. Stop and start conditions can be detected at any stage of the data transfer. If these conditions are asserted out of sequence with normal read and write operations, then they cause an immediate jump to the idle condition. During a given SCK high Rev. PrA | Page 16 of 27 Preliminary Technical Data ADN2816 REFERENCE CLOCK (OPTIONAL) A reference clock is not required to perform clock and data recovery with the ADN2816. However, support for an optional reference clock is provided. The reference clock can be driven differentially or single-ended. If the reference clock is not being used, then REFCLKP should be tied to VCC, and REFCLKN can be left floating or tied to VEE (the inputs are internally terminated to VCC/2). See Figure 15 through Figure 17 for sample configurations. The REFCLK input buffer accepts any differential signal with a peak-to-peak differential amplitude of greater than 100 mV (for example, LVPECL or LVDS) or a standard single-ended low voltage TTL input, providing maximum system flexibility. Phase noise and duty cycle of the reference clock are not critical and 100 ppm accuracy is sufficient. ADN2816 REFCLKP BUFFER 100kΩ 100kΩ VCC/2 04948-0-021 REFCLKN Figure 15. Differential REFCLK Configuration REFCLKP BUFFER NC 11 REFCLKN 100kΩ 100kΩ VCC/2 Figure 17. No REFCLK Configuration The two uses of the reference clock are mutually exclusive. The reference clock can be used either as an acquisition aid for the ADN2816 to lock onto data, or to measure the frequency of the incoming data to within 0.01%. (There is the capability to measure the data rate to approximately ±10% without the use of a reference clock.) The modes are mutually exclusive, because, in the first use, the user knows exactly what the data rate is and wants to force the part to lock onto only that data rate; in the second use, the user does not know what the data rate is and wants to measure it. Lock to reference mode is enabled by writing a 1 to I2C Register Bit CTRLA[0]. Fine data rate readback mode is enabled by writing a 1 to I2C Register Bit CTRLA[1]. Writing a 1 to both of these bits at the same time causes an indeterminate state and is not supported. Using the Reference Clock to Lock onto Data In this mode, the ADN2816 locks onto a frequency derived from the reference clock according to the following equation: The user must know exactly what the data rate is, and provide a reference clock that is a function of this rate. The ADN2816 can still be used as a continuous rate device in this configuration, provided that the user has the ability to provide a reference clock that has a variable frequency (see Application Note AN-632). 11 CLK OSC ADN2816 10 REFCLKP Data Rate/2CTRLA[5:2] = REFCLK/2CTRLA[7:6] 10 VCC VCC 04948-0-023 period, the user should issue one start condition, one stop condition, or a single stop condition followed by a single start condition. If an invalid subaddress is issued by the user, the ADN2816 does not issue an acknowledge and returns to the idle condition. If the user exceeds the highest subaddress while reading back in autoincrement mode, then the highest subaddress register contents continue to be output until the master device issues a no-acknowledge. This indicates the end of a read. In a no-acknowledge condition, the SDATA line is not pulled low on the ninth pulse. See Figure 6 and Figure 7 for sample read and write data transfers and Figure 8 for a more detailed timing diagram. ADN2816 OUT BUFFER 100kΩ 100kΩ VCC/2 Figure 16. Single-Ended REFCLK Configuration 04948-0-022 REFCLKN The reference clock can be anywhere between 12.3 MHz and 200 MHz. By default, the ADN2816 expects a reference clock of between 12.3 MHz and 25 MHz. If it is between 25 MHz and 50 MHz, 50 MHz and 100 MHz, or 100 MHz and 200 MHz, the user needs to configure the ADN2816 to use the correct reference frequency range by setting two bits of the CTRLA register, CTRLA[7:6]. Table 11. CTRLA Settings CTRLA[7:6] 00 01 10 11 Rev. PrA | Page 17 of 27 Range (MHz) 12.3 to 25 25 to 50 50 to 100 100 to 200 CTRLA[5:2] 0000 0001 n 1000 Ratio 1 2 2n 256 ADN2816 Preliminary Technical Data The user can specify a fixed integer multiple of the reference clock to lock onto using CTRLA[5:2], where CTRLA should be set to the data rate/DIV_FREF, where DIV_FREF represents the divided-down reference referred to the 12.3 MHz to 25 MHz band. For example, if the reference clock frequency was 38.88 MHz and the input data rate was 622.08 Mb/s, then CTRLA[7:6] would be set to [01] to give a divided-down reference clock of 19.44 MHz. CTRLA[5:2] would be set to [0101], that is, 5, because 622.08 Mb/s/19.44 MHz = 25 Step 2: Reset MISC[2] by writing a 1 followed by a 0 to CTRLB[3]. This initiates a new data rate measurement. Step 3: Read back MISC[2]. If it is 0, then the measurement is not complete. If it is 1, then the measurement is complete and the data rate can be read back on FREQ[22:0]. The time for a data rate measurement is typically 80 ms. Step 4: Read back the data rate from registers FREQ2[6:0], FREQ1[7:0], and FREQ0[7:0]. Use the following equation to determine the data rate: In this mode, if the ADN2816 loses lock for any reason, it relocks onto the reference clock and continues to output a stable clock. While the ADN2816 is operating in lock to reference mode, if the user ever changes the reference frequency, the FREF range (CTRLA[7:6]), or the FREF ratio (CTRLA[5:2]), this must be followed by writing a 0 to 1 transition into the CTRLA[0] bit to initiate a new lock to reference command. Using the Reference Clock to Measure Data Frequency The user can also provide a reference clock to measure the recovered data frequency. In this case, the user provides a reference clock, and the ADN2816 compares the frequency of the incoming data to the incoming reference clock and returns a ratio of the two frequencies to 0.01% (100 ppm). The accuracy error of the reference clock is added to the accuracy of the ADN2816 data rate measurement. For example, if a 100-ppm accuracy reference clock is used, the total accuracy of the measurement is within 200 ppm. The reference clock can range from 12.3 MHz and 200 MHz. The ADN2816 expects a reference clock between 12.3 MHz and 25 MHz by default. If it is between 25 MHz and 50 MHz, 50 MHz and 100 MHz, or 100 MHz and 200 MHz, the user needs to configure the ADN2816 to use the correct reference frequency range by setting two bits of the CTRLA register, CTRLA[7:6]. Using the reference clock to determine the frequency of the incoming data does not affect the manner in which the part locks onto data. In this mode, the reference clock is used only to determine the frequency of the data. For this reason, the user does not need to know the data rate to use the reference clock in this manner. f DATARATE = (FREQ [22..0]× f REFCLK )/ 2 (14 + SEL _ RATE ) where: FREQ[22:0] is the reading from FREQ2[6:0] (MSByte), FREQ1[7:0], and FREQ0[7:0] (LSByte). Table 12. D22 D21...D17 FREQ2[6:0] D16 D15 D14...D9 D8 FREQ1[7:0] D7 D6...D1 D0 FREQ0[7:0] fDATARATE is the data rate (Mb/s). fREFCLK is the REFCLK frequency (MHz). SEL_RATE is the setting from CTRLA[7:6]. For example, if the reference clock frequency is 32 MHz, SEL_RATE = 1, since the CTRLA[7:6] setting would be [01], because the reference frequency would fall into the 25 MHz to 50 MHz range. Assume for this example that the input data rate is 622.08 Mb/s (OC12). After following Steps 1 through 4, the value that is read back on FREQ[22:0] = 0x9B851, which is equal to 637 x 103. Plugging this value into the equation yields (637e3 × 32e6)/ (2(14+1) ) = 622.08Mb/s If subsequent frequency measurements are required, CTRLA[1] should remain set to 1. It does not need to be reset. The measurement process is reset by writing a 1 followed by a 0 to CTRLB[3]. This initiates a new data rate measurement. Follow Steps 2 through 4 to read back the new data rate. Note: A data rate readback is valid only if LOL is low. If LOL is high, the data rate readback is invalid. Prior to reading back the data rate using the reference clock, the CTRLA[7:6] bits must be set to the appropriate frequency range with respect to the reference clock being used. A fine data rate readback is then executed as follows: Step 1: Write a 1 to CTRLA[1]. This enables the fine data rate measurement capability of the ADN2816. This bit is level sensitive and does not need to be reset to perform subsequent frequency measurements. Rev. PrA | Page 18 of 27 Preliminary Technical Data ADN2816 Additional Features Available via the I2C Interface Coarse Data Rate Readback Table 13 provides coarse data rate readback to within ±10%. System Reset The data rate can be read back over the I2C interface to approximately +10% without the need of an external reference clock. A 9-bit register, COARSE_RD[8:0], can be read back when LOL is de-asserted. The 8 MSBs of this register are the contents of the RATE[7:0] register. The LSB of the COARSE_RD register is Bit MISC[0]. A frequency acquisition can be initiated by writing a 1 followed by a 0 to the I2C Register Bit CTRLB[5]. This initiates a new frequency acquisition while keeping the ADN2816 in the operating mode that it was previously programmed to in registers CTRL[A], CTRL[B], and CTRL[C]. Rev. PrA | Page 19 of 27 ADN2816 Preliminary Technical Data APPLICATIONS INFORMATION PCB DESIGN GUIDELINES If connections to the supply and ground are made through vias, the use of multiple vias in parallel helps to reduce series inductance, especially on Pin 24, which supplies power to the high speed CLKOUTP/CLKOUTN and DATAOUTP/ DATAOUTN output buffers. Refer to the schematic in Figure 18 for recommended connections. Proper RF PCB design techniques must be used for optimal performance. Power Supply Connections and Ground Planes Use of one low impedance ground plane is recommended. The VEE pins should be soldered directly to the ground plane to reduce series inductance. If the ground plane is an internal plane and connections to the ground plane are made through vias, multiple vias can be used in parallel to reduce the series inductance, especially on Pin 23, which is the ground return for the output buffers. The exposed pad should be connected to the GND plane using plugged vias so that solder does not leak through the vias during reflow. By using adjacent power supply and GND planes, excellent high frequency decoupling can be realized by using close spacing between the planes. This capacitance is given by Cplane = 0.88ε r A/d (pF ) where: Use of a 22 µF electrolytic capacitor between VCC and VEE is recommended at the location where the 3.3 V supply enters the PCB. When using 0.1 µF and 1 nF ceramic chip capacitors, they should be placed between the IC power supply VCC and VEE, as close as possible to the ADN2816 VCC pins. εr is the dielectric constant of the PCB material. A is the area of the overlap of power and GND planes (cm2). d is the separation between planes (mm). For FR-4, εr = 4.4 mm and 0.25 mm spacing, C ~15 pF/cm2. 50Ω TRANSMISSION LINES VCC DATAOUTP + 22µF 0.1µF DATAOUTN 1nF CLKOUTP TEST2 VCC VEE DATAOUTP DATAOUTN SQUELCH CLKOUTP CLKOUTN CLKOUTN 0.1µF 32 31 30 29 28 27 26 25 REFCLKP REFCLKN NC VCC VEE CF2 CF1 LOL 50Ω 50Ω 1nF VCC VEE NC SDA SCK SADDR5 VCC VEE 1nF 0.1µF I2C CONTROLLER I2C CONTROLLER VCC 0.1µF µC NC OPTICAL TRANSCEIVER MODULE 24 EXPOSED PAD 23 TIED OFF TO 22 VEE PLANE 21 20 WITH VIAS 19 18 17 VCC 0.1µF 1nF 0.47µF ±20% >300MΩ INSULATION RESISTANCE Figure 18. Typical ADN2816 Applications Circuit Rev. PrA | Page 20 of 27 04948-0-031 1nF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 0.1µF TEST1 VCC VREF NIN PIN NC NC VEE VCC Preliminary Technical Data ADN2816 Transmission Lines Use of 50 Ω transmission lines is required for all high frequency input and output signals to minimize reflections: PIN, NIN, CLKOUTP, CLKOUTN, DATAOUTP, DATAOUTN (also REFCLKP, REFCLKN, if a high frequency reference clock is used, such as 155 MHz). It is also necessary for the PIN/NIN input traces to be matched in length, and the CLKOUTP/N and DATAOUTP/N output traces to be matched in length to avoid skew between the differential traces. The high speed inputs, PIN and NIN, are internally terminated with 50 Ω to an internal reference voltage (see Figure 19). A 0.1 µF is recommended between VREF, Pin 3, and GND to provide an ac ground for the inputs. As with any high speed mixed-signal design, take care to keep all high speed digital traces away from sensitive analog nodes. rates used in the application. When choosing the capacitors, the time constant formed with the two 50 Ω resistors in the signal path must be considered. When a large number of consecutive identical digits (CIDs) are applied, the capacitor voltage can droop due to baseline wander (see Figure 20), causing patterndependent jitter (PDJ). The user must determine how much droop is tolerable and choose an ac coupling capacitor based on that amount of droop. The amount of PDJ can then be approximated based on the capacitor selection. The actual capacitor value selection may require some trade-offs between droop and PDJ. Example: Assuming that 2% droop can be tolerated, then the maximum differential droop is 4%. Normalizing to Vpp: Droop = ∆ V = 0.04 V = 0.5 Vpp (1 − e–t/τ) ; therefore, τ = 12t where: VCC τ is the RC time constant (C is the ac coupling capacitor, R = 100 Ω seen by C). ADN2816 50Ω CIN PIN 50Ω CIN NIN t is the total discharge time, which is equal to nΤ. 50Ω 0.1µF VREF n is the number of CIDs. 50Ω 3kΩ 2.5V T is the bit period. 04948-0-026 TIA The capacitor value can then be calculated by combining the equations for τ and t: Figure 19. ADN2816 AC-Coupled Input Configuration C = 12nT/R Soldering Guidelines for Chip Scale Package The lands on the 32 LFCSP are rectangular. The printed circuit board pad for these should be 0.1 mm longer than the package land length and 0.05 mm wider than the package land width. The land should be centered on the pad. This ensures that the solder joint size is maximized. The bottom of the chip scale package has a central exposed pad. The pad on the printed circuit board should be at least as large as this exposed pad. The user must connect the exposed pad to VEE using plugged vias so that solder does not leak through the vias during reflow. This ensures a solid connection from the exposed pad to VEE. Once the capacitor value is selected, the PDJ can be approximated as ( ) PDJ pspp = 0.5t r 1 − e (−nT/RC ) / 0.6 where: PDJpspp is the amount of pattern-dependent jitter allowed; < 0.01 UI p-p typical. Choosing AC Coupling Capacitors tr is the rise time, which is equal to 0.22/BW, where BW ~ 0.7 (bit rate). AC coupling capacitors at the input (PIN, NIN) and output (DATAOUTP, DATAOUTN) of the ADN2816 must be chosen such that the device works properly over the full range of data Note that this expression for tr is accurate only for the inputs. The output rise time for the ADN2816 is ~100 ps regardless of data rate. Rev. PrA | Page 21 of 27 ADN2816 Preliminary Technical Data VCC V1 TIA CIN V2 ADN2816 PIN V1b CIN V2b 50Ω COUT + 50Ω VREF 1 2 DATAOUTN COUT – NIN V1 DATAOUTP CDR BUFFER 3 4 V1b V2 VREF V2b VTH VDIFF NOTES: 1. DURING DATA PATTERNS WITH HIGH TRANSITION DENSITY, DIFFERENTIAL DC VOLTAGE AT V1 AND V2 IS ZERO. 2. WHEN THE OUTPUT OF THE TIA GOES TO CID, V1 AND V1b ARE DRIVEN TO DIFFERENT DC LEVELS. V2 AND V2b DISCHARGE TO THE VREF LEVEL, WHICH EFFECTIVELY INTRODUCES A DIFFERENTIAL DC OFFSET ACROSS THE AC COUPLING CAPACITORS. 3. WHEN THE BURST OF DATA STARTS AGAIN, THE DIFFERENTIAL DC OFFSET ACROSS THE AC COUPLING CAPACITORS IS APPLIED TO THE INPUT LEVELS CAUSING A DC SHIFT IN THE DIFFERENTIAL INPUT. THIS SHIFT IS LARGE ENOUGH SUCH THAT ONE OF THE STATES, EITHER HIGH OR LOW DEPENDING ON THE LEVELS OF V1 AND V1b WHEN THE TIA WENT TO CID, IS CANCELED OUT. THE QUANTIZER DOES NOT RECOGNIZE THIS AS A VALID STATE. 4. THE DC OFFSET SLOWLY DISCHARGES UNTIL THE DIFFERENTIAL INPUT VOLTAGE EXCEEDS THE SENSITIVITY OF THE ADN2816. THE QUANTIZER CAN RECOGNIZE BOTH HIGH AND LOW STATES AT THIS POINT. Figure 20. Example of Baseline Wander Rev. PrA | Page 22 of 27 04948-0-027 VDIFF = V2–V2b VTH = ADN2816 QUANTIZER THRESHOLD Preliminary Technical Data ADN2816 COARSE DATA RATE READBACK LOOK-UP TABLE Code is the 9-bit value read back from COARSE_RD[8:0]. Table 13. Look-Up Table Code 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 FMID 5.1934e+06 5.1930e+06 5.2930e+06 5.3989e+06 5.5124e+06 5.6325e+06 5.7612e+06 5.8995e+06 6.0473e+06 6.2097e+06 6.3819e+06 6.5675e+06 6.7688e+06 6.9874e+06 7.2262e+06 7.4863e+06 7.4139e+06 7.4135e+06 7.5606e+06 7.7173e+06 7.8852e+06 8.0633e+06 8.2548e+06 8.4586e+06 8.6784e+06 8.9180e+06 9.1736e+06 9.4481e+06 9.7464e+06 1.0068e+07 1.0417e+07 1.0791e+07 1.0387e+07 1.0386e+07 1.0586e+07 1.0798e+07 1.1025e+07 1.1265e+07 1.1522e+07 1.1799e+07 1.2095e+07 1.2419e+07 1.2764e+07 1.3135e+07 1.3538e+07 1.3975e+07 1.4452e+07 1.4973e+07 Code 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 FMID 1.4828e+07 1.4827e+07 1.5121e+07 1.5435e+07 1.5770e+07 1.6127e+07 1.6510e+07 1.6917e+07 1.7357e+07 1.7836e+07 1.8347e+07 1.8896e+07 1.9493e+07 2.0136e+07 2.0833e+07 2.1582e+07 2.0774e+07 2.0772e+07 2.1172e+07 2.1596e+07 2.2049e+07 2.2530e+07 2.3045e+07 2.3598e+07 2.4189e+07 2.4839e+07 2.5527e+07 2.6270e+07 2.7075e+07 2.7950e+07 2.8905e+07 2.9945e+07 2.9655e+07 2.9654e+07 3.0242e+07 3.0869e+07 3.1541e+07 3.2253e+07 3.3019e+07 3.3834e+07 3.4714e+07 3.5672e+07 3.6694e+07 3.7792e+07 3.8985e+07 4.0273e+07 4.1666e+07 4.3164e+07 Code 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 Rev. PrA | Page 23 of 27 FMID 4.1547e+07 4.1544e+07 4.2344e+07 4.3191e+07 4.4099e+07 4.5060e+07 4.6090e+07 4.7196e+07 4.8378e+07 4.9678e+07 5.1055e+07 5.2540e+07 5.4150e+07 5.5899e+07 5.7810e+07 5.9890e+07 5.9311e+07 5.9308e+07 6.0485e+07 6.1739e+07 6.3081e+07 6.4506e+07 6.6038e+07 6.7669e+07 6.9427e+07 7.1344e+07 7.3388e+07 7.5585e+07 7.7971e+07 8.0546e+07 8.3333e+07 8.6328e+07 8.3095e+07 8.3087e+07 8.4689e+07 8.6383e+07 8.8198e+07 9.0120e+07 9.2179e+07 9.4392e+07 9.6757e+07 9.9356e+07 1.0211e+08 1.0508e+08 1.0830e+08 1.1180e+08 1.1562e+08 1.1978e+08 Code 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 FMID 1.1862e+08 1.1862e+08 1.2097e+08 1.2348e+08 1.2616e+08 1.2901e+08 1.3208e+08 1.3534e+08 1.3885e+08 1.4269e+08 1.4678e+08 1.5117e+08 1.5594e+08 1.6109e+08 1.6667e+08 1.7266e+08 1.6619e+08 1.6617e+08 1.6938e+08 1.7277e+08 1.7640e+08 1.8024e+08 1.8436e+08 1.8878e+08 1.9351e+08 1.9871e+08 2.0422e+08 2.1016e+08 2.1660e+08 2.2360e+08 2.3124e+08 2.3956e+08 2.3724e+08 2.3723e+08 2.4194e+08 2.4695e+08 2.5233e+08 2.5802e+08 2.6415e+08 2.7067e+08 2.7771e+08 2.8538e+08 2.9355e+08 3.0234e+08 3.1188e+08 3.2218e+08 3.3333e+08 3.4531e+08 ADN2816 Code 192 193 194 195 196 197 198 199 200 FMID 3.3238e+08 3.3235e+08 3.3876e+08 3.4553e+08 3.5279e+08 3.6048e+08 3.6872e+08 3.7757e+08 3.8703e+08 Preliminary Technical Data Code 201 202 203 204 205 206 207 208 209 FMID 3.9742e+08 4.0844e+08 4.2032e+08 4.3320e+08 4.4719e+08 4.6248e+08 4.7912e+08 4.7449e+08 4.7447e+08 Code 210 211 212 213 214 215 216 217 218 Rev. PrA | Page 24 of 27 FMID 4.8388e+08 4.9391e+08 5.0465e+08 5.1605e+08 5.2831e+08 5.4135e+08 5.5542e+08 5.7075e+08 5.8711e+08 Code 219 220 221 222 223 224 225 226 227 FMID 6.0468e+08 6.2377e+08 6.4437e+08 6.6666e+08 6.9062e+08 6.6476e+08 6.6470e+08 6.7751e+08 6.9106e+08 Preliminary Technical Data ADN2816 OUTLINE DIMENSIONS 5.00 BSC SQ 0.60 MAX 0.50 BSC 4.75 BSC SQ TOP VIEW 0.50 0.40 0.30 1.00 0.85 0.80 32 25 24 PIN 1 INDICATOR 12° MAX PIN 1 INDICATOR 0.60 MAX 1 3.25 3.10 SQ 2.95 BOTTOM VIEW 17 16 9 8 0.25 MIN 3.50 REF 0.80 MAX 0.65 TYP 0.05 MAX 0.02 NOM SEATING PLANE 0.30 0.23 0.18 0.20 REF COPLANARITY 0.08 COMPLIANT TO JEDEC STANDARDS MO-220-VHHD-2 Figure 21. 32-Lead Frame Chip Scale Package [LFCSP] (CP-32) Dimensions shown in millimeters ORDERING GUIDE Model ADN2816XCPZ Temperature Range −40°C to 85°C Package Description Pb Free 32-LFCSP Rev. PrA | Page 25 of 27 Package Option CP-32 ADN2816 Preliminary Technical Data NOTES Rev. PrA | Page 26 of 27 Preliminary Technical Data ADN2816 NOTES Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips. © 2004 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. PR04948-0-8/04(PrA) Rev. PrA | Page 27 of 27