155/622 Mb/s Clock and Data Recovery IC with Integrated Limiting Amp ADN2807 FEATURES GENERAL DESCRIPTION Meets SONET requirements for jitter transfer/ generation/tolerance Quantizer sensitivity: 4 mV typical Adjustable slice level: ±100 mV Patented clock recovery architecture Loss-of-signal detect range: 3 mV to 15 mV Single-reference clock frequency for all rates, including 15/14 (7%) wrapper rate Choice of 19.44 MHz, 38.88 MHz, 77.76 MHz, or 155.52 MHz REFCLK REFCLK inputs: LVPECL/LVDS/LVCMOS/LVTTL compatible (LVPECL/LVDS only at 155.52 MHz) Optional 19.44 MHz on-chip oscillator to be used with external crystal Loss-of-lock indicator Loopback mode for high speed test data Output squelch and bypass features Single-supply operation: 3.3 V Low power: 540 mW typical 7 mm × 7 mm, 48-lead LFCSP The ADN2807 provides the receiver functions of quantization, signal level detect, and clock and data recovery at rates of OC-3, OC-12, and 15/14 FEC. All SONET jitter requirements are met, including jitter transfer, jitter generation, and jitter tolerance. All specifications are quoted for –40°C to +85°C ambient temperature, unless otherwise noted. APPLICATIONS The ADN2807 is available in a compact 7 mm × 7 mm 48-lead chip-scale package (LFCSP). The device is intended for WDM system applications and can be used with either an external reference clock or an on-chip oscillator with external crystal. Both native rates and 15/14 rate digital wrappers are supported by the ADN2807, without any change of reference clock. This device, together with a PIN diode and a TIA preamplifier, can implement a highly integrated, low cost, low power, fiber optic receiver. The receiver front end signal detect circuit indicates when the input signal level has fallen below a user adjustable threshold. The signal detect circuit has hysteresis to prevent chatter at the output. SONET OC-3/-12, SDH STM-1/-4 and, 15/14 FEC rates WDM transponders Regenerators/repeaters Test equipment Passive optical networks FUNCTIONAL BLOCK DIAGRAM SLICEP/N 2 VCC VEE CF1 ADN2807 CF2 LOL LOOP FILTER 2 PIN 2 QUANTIZER NIN PHASE SHIFTER PHASE DET. LOOP FILTER VCO FREQUENCY LOCK DETECTOR /n REFSEL[0..1] REFCLKP/N XO1 XTAL OSC XO2 LEVEL DETECT DATA RETIMING DIVIDER 1/2/4/16 3 2 THRADJ SDOUT DATAOUTP/N 2 CLKOUTP/N REFSEL 03877-0-001 VREF FRACTIONAL DIVIDER SEL[0..2] Figure 1. Rev. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.326.8703 © 2004 Analog Devices, Inc. All rights reserved. ADN2807 TABLE OF CONTENTS Specifications..................................................................................... 3 Limiting Amplifier ..................................................................... 12 Absolute Maximum Ratings............................................................ 5 Slice Adjust .................................................................................. 12 Thermal Characteristics .............................................................. 5 Loss-of-Signal (LOS) Detector ................................................. 12 ESD Caution.................................................................................. 5 Reference Clock.......................................................................... 12 Pin Configuration and Function Descriptions............................. 6 Lock Detector Operation .......................................................... 13 Definition of Terms .......................................................................... 8 Squelch Mode ............................................................................. 14 Maximum, Minimum, and Typical Specifications ................... 8 Test Modes—Bypass and Loop-back....................................... 14 Input Sensitivity and Input Overdrive....................................... 8 Application Information................................................................ 15 Single-Ended vs. Differential ...................................................... 8 PCB Design Guidelines ............................................................. 15 LOS Response Time ..................................................................... 9 Choosing AC Coupling Capacitors.......................................... 17 Jitter Specifications....................................................................... 9 DC-Coupled Application .......................................................... 17 Theory of Operation ...................................................................... 10 LOL Toggling during Loss of Input Data................................ 17 Functional Description .................................................................. 12 Outline Dimensions ....................................................................... 19 Multirate Clock and Data Recovery......................................... 12 Ordering Guide .......................................................................... 19 REVISION HISTORY 5/04—Data Sheet Changed from Rev. 0 to Rev. A Changes to Specifications ............................................................ 3 Change to Table 7 and Table 8 .................................................. 13 1/04—Revision 0: Initial Version Rev. A | Page 2 of 20 ADN2807 SPECIFICATIONS Table 1. TA = TMIN to TMAX, VCC = VMIN to VMAX, VEE = 0 V, CF = 4.7 µF, SLICEP = SLICEN = VCC, unless otherwise noted Parameter QUANTIZER–DC CHARACTERISTICS Input Voltage Range Peak-to-Peak Differential Input Input Common-Mode Level Differential Input Sensitivity Input Overdrive Input Offset Input RMS Noise QUANTIZER–AC CHARACTERISTICS Small Signal Gain Input Resistance Input Capacitance Pulse-Width Distortion2 QUANTIZER SLICE ADJUSTMENT Gain Control Voltage Range Slice Threshold Offset LEVEL SIGNAL DETECT (SDOUT) Level Detect Range (See Figure 4) Response Time Hysteresis (Electrical) Conditions Min @ PIN or NIN, dc-coupled 0 DC-coupled (See Figure 26) PIN−NIN, ac-coupled1, BER = 1 × 10–10 See Figure 8 0.4 Differential Differential Max Unit 1.2 2.4 V V V mV p-p mV p-p µV µV rms 10 5 54 100 0.65 10 0.11 –0.8 1.3 0.20 dB Ω pF ps 0.30 +0.8 VCC V/V V V mV ±1.0 RTHRESH = 2 kΩ RTHRESH = 20 kΩ RTHRESH = 90 kΩ DC-coupled OC-12, PRBS 223 RTHRESH = 2 kΩ RTHRESH = 20 kΩ RTHRESH = 90 kΩ RTHRESH = 90 kΩ @ 25°C OC-3, PRBS 223 RTHRESH = 2 kΩ RTHRESH = 20 kΩ RTHRESH = 90 kΩ RTHRESH = 90 k @ 25°C OC-12, PRBS 27 RTHRESH = 2 kΩ RTHRESH = 20 kΩ RTHRESH = 90 kΩ OC-3, PRBS 27 RTHRESH = 2 kΩ RTHRESH = 20 kΩ RTHRESH = 90 kΩ LOSS-OF-LOCK DETECTOR (LOL) Loss-of-Lock Response Time POWER SUPPLY VOLTAGE POWER SUPPLY CURRENT 4 2 500 244 BER = 1 × 10–10 SliceP – SliceN = ±0.5 V SliceP – SliceN @ SliceP or SliceN Typ 9.4 2.5 0.7 0.1 13.3 5.3 3.0 0.3 18.0 7.6 5.2 5 mV mV mV µs 4.7 1.8 6.4 6.0 6.3 6.9 7.8 10.0 dB dB dB dB 4.8 3.6 3.4 6.2 5.6 5.6 6.6 9.9 dB dB dB dB 5.7 3.9 3.2 6.6 6.2 6.7 7.8 8.5 9.9 dB dB dB 5.4 4.6 3.9 6.6 6.4 6.8 7.7 8.2 9.7 dB dB dB 3.0 150 60 3.3 164 3.6 215 mV V mA From fVCO error > 1000 ppm Rev. A | Page 3 of 20 8.9 8.5 ADN2807 Parameter PHASE-LOCKED LOOP CHARACTERISTICS Jitter Transfer BW Jitter Peaking Jitter Generation Conditions PIN–NIN = 10 mV p-p OC-12 OC-3 OC-12 OC-3 OC-12, 12 kHz to 5 MHz Min Typ Max Unit 140 48 0.004 0.002 200 85 kHz kHz dB dB UI rms UI p-p UI rms UI p-p 0.02 OC-3, 12 kHz to 1.3 MHz 0.02 Jitter Tolerance CML OUTPUTS (CLKOUTP/N, DATAOUTP/N) Single-Ended Output Swing Differential Output Swing Output High Voltage Output Low Voltage Rise Time Fall Time Setup Time Hold Time REFCLK DC INPUT CHARACTERISTICS Input Voltage Range Peak-to-Peak Differential Input Common-Mode Level TEST DATA DC INPUT CHARACTERISTICS4 (TDINP/N) Peak-to-Peak Differential Input Voltage LVTTL DC INPUT CHARACTERISTICS Input High Voltage Input Low Voltage Input Current Input Current (SEL0 and SEL1 Only)5 LVTTL DC OUTPUT CHARACTERISTICS Output High Voltage Output Low Voltage OC-12 30 Hz3 300 Hz 25 kHz 250 kHz3 OC-3 30 Hz3 300 Hz3 6500 Hz 65 kHz3 100 44 5.8 1.0 UI p-p UI p-p UI p-p UI p-p 50 23.5 6.0 1.0 UI p-p UI p-p UI p-p UI p-p VSE (See Figure 7) VDIFF (See Figure 7) VOH VOL, referred to VCC 20% to 80% 80% to 20% TS (See Figure 3) OC-12 OC-3 TH (See Figure 3) OC-12 OC-3 400 850 @ REFCLKP or REFCLKN 0 100 750 3150 ps ps VOH, IOH = –2.0 mA VOL, IOL = +2.0 mA 2.4 –5 –5 PIN and NIN should be driven differentially, ac-coupled for optimum sensitivity. PWD measurement made on quantizer outputs in BYPASS mode. Jitter tolerance measurements are equipment limited. 4 TDINP/N are CML inputs. If the drivers to the TDINP/N inputs are anything other than CML, they must be ac-coupled. 5 SEL0 and SEL1 have internal pull-down resistors, causing higher IIH. Rev. A | Page 4 of 20 –0.30 150 150 mV mV V V ps ps ps ps 2.0 3 540 1100 750 3145 VIH VIL VIN = 0.4 V or VIN = 2.4 V VIN = 0.4 V or VIN = 2.4 V 2 488 975 VCC –0.60 DC-coupled, single-ended CML inputs 1 0.003 0.04 0.002 0.04 VCC VCC/2 V mV V 0.8 V 0.8 +5 +50 V V µA µA 0.4 V V ADN2807 ABSOLUTE MAXIMUM RATINGS Table 2. Parameter Supply Voltage (VCC) Minimum Input Voltage (All Inputs) Maximum Input Voltage (All Inputs) Maximum Junction Temperature Storage Temperature Lead Temperature (Soldering 10 sec) THERMAL CHARACTERISTICS Rating 5.5 V VEE – 0.4 V VCC + 0.4 V 165°C –65°C to +150°C 300°C Thermal Resistance 48-Lead LFCSP, 4-layer board with exposed paddle soldered to VCC θJA = 25°C/W Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. A | Page 5 of 20 ADN2807 48 LOOPEN 47 VCC 46 VEE 45 SDOUT 44 BYPASS 43 VEE 42 VEE 41 CLKOUTP 40 CLKOUTN 39 SQUELCH 38 DATAOUTP 37 DATAOUTN PIN CONFIGURATION AND FUNCTION DESCRIPTIONS ADN2807 TOPVIEW 36 VCC 35 VCC 34 VEE 33 VEE 32 SEL0 31 NC 30 SEL1 29 VEE 28 VCC 27 VEE 26 VCC 25 CF2 03877-0-002 PIN 1 INDICATOR REFCLKN 13 REFCLKP 14 REFSEL 15 VEE 16 TDINP 17 TDINN 18 VEE 19 VCC 20 CF1 21 VEE 22 REFSEL1 23 REFSEL0 24 THRADJ 1 VCC 2 VEE 3 VREF 4 PIN 5 NIN 6 SLICEP 7 SLICEN 8 VEE 9 LOL 10 XO1 11 XO2 12 Figure 2. Pin Configuration Table 3. Pin Function Descriptions Pin No. 1 2, 26, 28, Pad 3, 9, 16, 19, 22, 27, 29, 33, 34, 42, 43, 46 4 5 6 7 8 10 11 12 13 14 15 17 18 20, 47 21 23 24 25 30 31 32 35, 36 37 38 39 40 41 44 45 48 Mnemonic THRADJ VCC VEE Type1 AI P P Description LOS Threshold Setting Resistor. Analog Supply. Ground. VREF PIN NIN SLICEP SLICEN LOL XO1 XO2 REFCLKN REFCLKP REFSEL TDINP TDINN VCC CF1 REFSEL1 REFSEL0 CF2 SEL1 NC SEL0 VCC DATAOUTN DATAOUTP SQUELCH CLKOUTN CLKOUTP BYPASS SDOUT LOOPEN AO AI AI AI AI DO AO AO DI DI DI AI AI P AO DI DI AO DI Internal VREF Voltage. Decouple to GND with a 0.1 µF capacitor. Differential Data Input. Differential Data Input. Differential Slice Level Adjust Input. Differential Slice Level Adjust Input. Loss-of-Lock Indicator. LVTTL active high. Crystal Oscillator. Crystal Oscillator. Differential REFCLK Input. LVTTL, LVCMOS, LVPECL, LVDS (LVPECL, LVDS only at 155.52 MHz). Differential REFCLK Input. LVTTL, LVCMOS, LVPECL, LVDS (LVPECL, LVDS only at 155.52 MHz). Reference Source Select. 0 = on-chip oscillator with external crystal. 1 = external clock source, LVTTL. Differential Test Data Input. CML. Differential Test Data Input. CML. Digital Supply. Frequency Loop Capacitor. Reference Frequency Select (See Table 6) LVTTL. Reference Frequency Select (See Table 6) LVTTL. Frequency Loop Capacitor. Data Rate Select (See Table 5) LVTTL. No Connect. Data Rate Select (See Table 5) LVTTL. Output Driver Supply. Differential Retimed Data Output. CML. Differential Retimed Data Output. CML. Disable Clock and Data Outputs. Active high. LVTTL. Differential Recovered Clock Output. CML. Differential Recovered Clock Output. CML. Bypass CDR Mode. Active high. LVTTL. Loss-of-Signal Detect Output. Active high. LVTTL. Enable Test Data Inputs. Active high. LVTTL. DI P DO DO DI DO DO DI DO DI 1 Type: P = Power, AI = Analog Input, AO = Analog Output, DI = Digital Input, DO = Digital Output Rev. A | Page 6 of 20 ADN2807 CLKOUTP TH 03877-0-003 TS DATAOUTP/N Figure 3. Output Timing 18 THRADJ RESISTOR VS. LOS TRIP POINT 16 14 12 mV 10 8 6 03877-0-004 4 2 0 10 0 20 30 40 50 60 RESISTANCE (kΩ) 70 80 90 100 Figure 4. LOS Comparator Trip Point Programming 10 18 9 16 8 14 FREQUENCY 12 6 5 4 8 03877-0-006 4 2 2 1 0 1 2 3 4 5 6 7 HYSTERESIS (dB) 8 9 10 0 0 1 2 3 4 5 6 7 8 Figure 5. LOS Hysteresis OC-3, −40°C, 3.6 V, 223 –1 PRBS Input Pattern, RTH = 90 kΩ Figure 6. LOS Hysteresis OC-12, −40°C, 3.6 V, 223 –1 PRBS Input Pattern, RTH = 90 kΩ OUTP VCML VSE OUTN OUTP–OUTN VSE 0V 9 HYSTERESIS (dB) VDIFF 03877-0-007 0 10 6 3 03877-0-005 FREQUENCY 7 Figure 7. Single-Ended vs. Differential Output Specifications Rev. A | Page 7 of 20 10 ADN2807 DEFINITION OF TERMS MAXIMUM, MINIMUM, AND TYPICAL SPECIFICATIONS SINGLE-ENDED VS. DIFFERENTIAL Specifications for every parameter are derived from statistical analyses of data taken on multiple devices from multiple wafer lots. Typical specifications are the mean of the distribution of the data for that parameter. If a parameter has a maximum (or a minimum) value, that value is calculated by adding to (or subtracting from) the mean six times the standard deviation of the distribution. This procedure is intended to tolerate production variations. If the mean shifts by 1.5 standard deviations, the remaining 4.5 standard deviations still provide a failure rate of only 3.4 parts per million. For all tested parameters, the test limits are guardbanded to account for tester variation, and therefore guarantee that no device is shipped outside of data sheet specifications. AC coupling is typically used to drive the inputs to the quantizer. The inputs are internally dc-biased to a commonmode potential of ~0.6 V. Driving the ADN2807 single-ended and observing the quantizer input with an oscilloscope probe at the point indicated in Figure 9 shows a binary signal with average value equal to the common-mode potential and instantaneous values both above and below the average value. It is convenient to measure the peak-to-peak amplitude of this signal and call the minimum required value the quantizer sensitivity. Referring to Figure 8, since both positive and negative offsets need to be accommodated, the sensitivity is twice the overdrive. 10mV p-p VREF INPUT SENSITIVITY AND INPUT OVERDRIVE SCOPE PROBE Sensitivity and overdrive specifications for the quantizer involve offset voltage, gain, and noise. The relationship between the logic output of the quantizer and the analog voltage input is shown in Figure 8. For sufficiently large positive input voltage, the output is always Logic 1; similarly for negative inputs, the output is always Logic 0. However, the transitions between output Logic Levels 1 and 0 are not at precisely defined input voltage levels, but occur over a range of input voltages. Within this zone of confusion, the output may be either 1 or 0, or it may even fail to attain a valid logic state. The width of this zone is determined by the input voltage noise of the quantizer. The center of the zone of confusion is the quantizer input offset voltage. Input overdrive is the magnitude of signal required to guarantee a correct logic level with a 1 × 10–10 confidence level. ADN2807 PIN + QUANTIZER 50Ω 03877-0-007 Figure 9. Single-Ended Sensitivity Measurement 5mV p-p VREF OUTPUT SCOPE PROBE ADN2807 NOISE 1 50Ω VREF PIN + QUANTIZER NIN 0 50Ω 50Ω VREF OVERDRIVE SENSITIVITY (2× OVERDRIVE) Figure 8. Input Sensitivity and Input Overdrive 03877-0-010 INPUT (V p-p) 03877-0-008 OFFSET Figure 10. Differential Sensitivity Measurement Driving the ADN2807 differentially (Figure 10), sensitivity seems to improve by observing the quantizer input with an oscilloscope probe. This is an illusion caused by the use of a single-ended probe. A 5 mV p-p signal appears to drive the ADN2807 quantizer. However, the single-ended probe measures only half the signal. The true quantizer input signal is twice this value since the other quantizer input is complementary to the signal being observed. Rev. A | Page 8 of 20 ADN2807 LOS RESPONSE TIME 0.1 JITTER GAIN (dB) The LOS response time is the delay between the removal of the input signal and indication of loss of signal (LOS) at SDOUT. The ADN2807’s response time is 300 ns typ when the inputs are dc-coupled. In practice, the time constant of ac coupling at the quantizer input determines the LOS response time. SLOPE = –20dB/DECADE ACCEPTABLE RANGE The jitter generation specification limits the amount of jitter that can be generated by the device with no jitter and wander applied at the input. Jitter Transfer The jitter transfer function is the ratio of the jitter on the output signal to the jitter applied on the input signal versus the frequency. This parameter measures the limited amount of jitter on an input signal that can be transferred to the output signal (Figure 11). Figure 11. Jitter Transfer Curve Jitter Tolerance The jitter tolerance is defined as the peak-to-peak amplitude of the sinusoidal jitter applied on the input signal that causes a 1 dB power penalty. This is a stress test intended to ensure that no additional penalty is incurred under the operating conditions (Figure 12). 15 SLOPE = –20dB/DECADE 1.5 03877-0-012 Jitter Generation fC JITTER FREQUENCY (kHz) INPUT JITTER AMPLITUDE (UI) The ADN2807 CDR is designed to achieve the best bit-errorrate (BER) performance, and has exceeded the jitter transfer, generation, and tolerance specifications proposed for SONET/SDH equipment defined in the Telcordia Technologies specification. Jitter is the dynamic displacement of digital signal edges from their long-term average positions measured in UI (unit intervals), where 1 UI = 1 bit period. Jitter on the input data can cause dynamic phase errors on the recovered clock sampling edge. Jitter on the recovered clock causes jitter on the retimed data. The following sections briefly summarize the specifications of the jitter generation, transfer, and tolerance in accordance with the Telcordia document (GR-253-CORE, Issue 3, September 2000) for the optical interface at the equipment level, and the ADN2807 performance with respect to those specifications. 03877-0-011 JITTER SPECIFICATIONS 0.15 f0 f1 f2 f3 f4 JITTER FREQUENCY (Hz) Figure 12. SONET Jitter Tolerance Mask Table 4. Jitter Transfer and Tolerance: SONET Specifications vs. ADN2807 Rate OC-12 OC-3 2 SONET Spec (fC) 500 kHz 130 kHz Jitter Transfer ADN2807 Implementation (kHz) Margin 140 3.6 48 2.7 Mask Corner Frequency (kHz) 250 kHz 65 kHz Jitter Tolerance SONET Spec ADN2807 (UI p-p) 4.8 MHz 0.15 600 kHz 0.15 Jitter tolerance measurements are limited by test equipment capabilities. Rev. A | Page 9 of 20 ADN2807 (UI p-p) 1.0 1.0 Implementation Margin2 6.67 6.67 ADN2807 THEORY OF OPERATION Another view of the circuit is that the phase shifter implements the zero required for the frequency compensation of a secondorder phase-locked loop. This zero is placed in the feedback path and, therefore, does not appear in the closed-loop transfer function. Jitter peaking in a conventional second-order phaselocked loop is caused by the presence of this zero in the closedloop transfer function. Since this circuit has no zero in the closed-loop transfer, jitter peaking is minimized. The delay- and phase-locked loops together simultaneously provide wideband jitter accommodation and narrow-band jitter filtering. The linearized block diagram in Figure 13 shows that the jitter transfer function, Z(s)/X(s), is a second-order low-pass providing excellent filtering. Note that the jitter transfer has no zero, unlike an ordinary second-order phase-locked loop. This means the main PLL loop has low jitter peaking (Figure 14), which makes this circuit ideal for signal regenerator applications where jitter peaking in a cascade of regenerators can contribute to hazardous jitter accumulation. psh INPUT DATA X(s) e(s) o/s d/sc 1/n Z(s) RECOVERED CLOCK d = PHASE DETECTOR GAIN o = VCO GAIN c = LOOP INTEGRATOR psh = PHASE SHIFTER GAIN n = DIVIDE RATIO JITTER TRANSFER FUNCTION Z(s) 1 = cn n psh X(s) +s +1 s2 do o TRACKING ERROR TRANSFER FUNCTION e(s) = X(s) s2 + s s2 d psh do + c cn 03877-0-013 The ADN2807 is a delay-locked and phase-locked loop circuit for clock recovery and data retiming from an NRZ encoded data stream. The phase of the input data signal is tracked by two separate feedback loops that share a common control voltage. A high speed delay-locked loop path uses a voltage controlled phase shifter to track the high frequency components of the input jitter. A separate phase control loop, comprised of the VCO, tracks the low frequency components of the input jitter. The initial frequency of the VCO is set by a third loop, which compares the VCO frequency with the reference frequency and sets the coarse tuning voltage. The jitter tracking phase-locked loop controls the VCO by the fine tuning control. The delayand phase-locked loops together track the phase of the input data signal. For example, when the clock lags input data, the phase detector drives the VCO to a higher frequency and also increases the delay through the phase shifter. Both of these actions serve to reduce the phase error between the clock and data. The faster clock picks up phase while the delayed data loses phase. Since the loop filter is an integrator, the static phase error will be driven to zero. Figure 13. PLL/DLL Architecture The error transfer, e(s)/X(s), has the same high-pass form as an ordinary phase-locked loop. This transfer function is free to be optimized to give excellent wideband jitter accommodation since the jitter transfer function, Z(s)/X(s), provides the narrowband jitter filtering. See Table 4 for error transfer bandwidths and jitter transfer bandwidths at the various data rates. The delay-locked and phase-locked loops contribute to overall jitter accommodation. At low frequencies of input jitter on the data signal, the integrator in the loop filter provides high gain to track large jitter amplitudes with small phase error. In this case, the VCO is frequency modulated, and jitter is tracked as in an ordinary phase-locked loop. The amount of low frequency jitter that can be tracked is a function of the VCO tuning range. A wider tuning range gives larger accommodation of low frequency jitter. The internal loop control voltage remains small for small phase errors, so the phase shifter remains close to the center of its range and thus contributes little to the low frequency jitter accommodation. Rev. A | Page 10 of 20 ADN2807 the eye opening of the input data, the static phase error, and the residual loop jitter generation. The jitter accommodation is roughly 0.5 UI in this region. The corner frequency between the declining slope and the flat region is the closed loop bandwidth of the delay-locked loop, which is roughly 5 MHz for OC-12 data rates and 600 kHz for OC-3 data rates. The gain of the loop integrator is small for high jitter frequencies, so larger phase differences are needed to make the loop control voltage big enough to tune the range of the phase shifter. Large phase errors at high jitter frequencies cannot be tolerated. In this region, the gain of the integrator determines the jitter accommodation. Since the gain of the loop integrator declines linearly with frequency, jitter accommodation is lower with higher jitter frequency. At the highest frequencies, the loop gain is very small, and little tuning of the phase shifter can be expected. In this case, jitter accommodation is determined by Rev. A | Page 11 of 20 JITTER PEAKING IN ORDINARY PLL JITTER GAIN (dB) ADN2807 Z(s) X(s) o n psh d psh c f (kHz) Figure 14. Jitter Response vs. Conventional PLL 03877-0-014 At medium jitter frequencies, the gain and tuning range of the VCO are not large enough to track the input jitter. In this case, the VCO control voltage becomes large and saturates, and the VCO frequency dwells at one or the other extreme of its tuning range. The size of the VCO tuning range, therefore, has only a small affect on the jitter accommodation. The delay-locked loop control voltage is now larger; therefore, the phase shifter takes on the burden of tracking the input jitter. The phase shifter range, in UI, can be seen as a broad plateau on the jitter tolerance curve. The phase shifter has a minimum range of 2 UI at all data rates. ADN2807 FUNCTIONAL DESCRIPTION MULTIRATE CLOCK AND DATA RECOVERY The ADN2807 recovers clock and data from serial bit streams at OC-3, OC-12 data rates as well as the 15/14 FEC rates. The output of the 2.5 GHz VCO is divided down in order to support the lower data rates. The data rate is selected by the SEL[2..0] inputs (Table 5). Table 5. Data Rate Selection Frequency (MHz) 622.08 155.52 666.51 166.63 REFERENCE CLOCK There are three options for providing the reference frequency to the ADN2807: differential clock, single-ended clock, or crystal oscillator. See Figure 15 to Figure 17 for example configurations. ADN2807 LIMITING AMPLIFIER REFCLKP The limiting amplifier has differential inputs (PIN/NIN) that are internally terminated with 50 Ω to an on-chip voltage reference (VREF = 0.6 V typically). These inputs are normally ac-coupled, although dc-coupling is possible as long as the input common-mode voltage remains above 0.4 V (Figure 24 to Figure 26 in the Applications Information section). Input offset is factory trimmed to achieve better than 4 mV typical sensitivity with minimal drift. The limiting amplifier can be driven differentially or single-ended. BUFFER REFCLKN 100kΩ VCC/2 VCC VCC XO1 XO2 VCC SLICE ADJUST The quantizer slicing level can be offset by ±100 mV to mitigate the effect of ASE (amplified spontaneous emission) noise by applying a differential voltage input of ±0.8 V to SLICEP/N inputs. If no adjustment of the slice level is needed, SLICEP/N should be tied to VCC. CRYSTAL OSCILLATOR REFSEL Figure 15. Differential REFCLK Configuration ADN2807 VCC REFCLKP CLK OSC LOSS-OF-SIGNAL (LOS) DETECTOR 100kΩ 03877-0-015 Rate OC-12 OC-3 OC-12 FEC OC-3 FEC OUT BUFFER The receiver front end level signal detect circuit indicates when the input signal level has fallen below a user adjustable threshold. The threshold is set with a single external resistor from THRADJ (Pin 1) to GND. The LOS comparator trip point versus the resistor value is illustrated in Figure 4 (this is only valid for SLICEP = SLICEN = VCC). If the input level to the ADN2807 drops below the programmed LOS threshold, SDOUT (Pin 45) will indicate the loss-of-signal condition with a Logic 1. The LOS response time is ~300 ns by design but will be dominated by the RC time constant in ac-coupled applications. If the LOS detector is used, the quantizer slice adjust pins must both be tied to VCC. This is to avoid interaction with the LOS threshold level. Rev. A | Page 12 of 20 REFCLKN NC 100kΩ 100kΩ VCC/2 VCC VCC VCC XO1 XO2 CRYSTAL OSCILLATOR REFSEL Figure 16. Single-Ended REFCLK Configuration 03877-0-016 SEL[1..0] 00 01 10 11 Note that it is not expected to use both LOS and slice adjust at the same time. Systems with optical amplifiers need the slice adjust to evade ASE. However, a loss-of-signal in an optical link that uses optical amplifiers causes the optical amplifier output to be full-scale noise. Under this condition, the LOS would not detect the failure. In this case, the loss-of-lock signal indicates the failure because the CDR circuitry is unable to lock onto a signal that is full-scale noise. ADN2807 Table 7. Required Crystal Specifications ADN2807 Parameter Mode Frequency/Overall Stability Frequency Accuracy Temperature Stability Aging ESR VCC REFCLKP BUFFER NC REFCLKN 100kΩ 100kΩ VCC/2 XO1 XO2 REFSEL must be tied to VCC when the REFCLKN/P inputs are active or to VEE when the oscillator is used. No connection between the XO pin and REFCLK input is necessary (Figure 15 to Figure 17). Note that the crystal should operate in series resonant mode, which renders it insensitive to external parasitics. No trimming capacitors are required. CRYSTAL OSCILLATOR 03877-0-017 19.44MHz REFSEL Value Series Resonant 19.44 MHz ± 100 ppm ±100 ppm ±100 ppm ±100 ppm 50 Ω max Figure 17. Crystal Oscillator Configuration LOCK DETECTOR OPERATION The ADN2807 can accept any of the following reference clock frequencies: 19.44 MHz, 38.88 MHz, and 77.76 MHz at LVTTL/ LVCMOS/LVPECL/LVDS levels, or 155.52 MHz at LVPECL/ LVDS levels via the REFCLKN/P inputs, independent of data rate. The input buffer accepts any differential signal with a peak-to-peak differential amplitude of greater than 100 mV (e.g., LVPECL or LVDS) or a standard single-ended low voltage TTL input, providing maximum system flexibility. The appropriate division ratio can be selected using the REFSEL0/1 pins according to Table 6. Phase noise and duty cycle of the reference clock are not critical, and 100 ppm accuracy is sufficient. The lock detector monitors the frequency difference between the VCO and the reference clock and deasserts the loss-of-lock signal when the VCO is within 500 ppm of center frequency. This enables the phase loop, which then maintains phase lock, unless the frequency error exceeds 0.1%. Should this occur, the loss-of-lock signal is reasserted and control returns to the frequency loop, which will reacquire and maintain a stable clock signal at the output. The frequency loop requires a single external capacitor between CF1 and CF2. The capacitor specification is given in Table 8. Table 8. Recommended CF Capacitor Specification An on-chip oscillator to be used with an external crystal is also provided as an alternative to using the REFCLKN/P inputs. Details of the recommended crystal are given in Table 7. Parameter Temperature Range Capacitance Leakage Rating Table 6. Reference Frequency Selection REFSEL[1..0] 00 01 10 11 XX Applied Reference Frequency (MHz) 19.44 38.88 77.76 155.52 REFCLKP/N Inactive. Use 19.44 MHz XTAL on Pins XO1, XO2 (Pull REFCLKP to VCC) LOL 1 1000 500 0 500 Figure 18. Transfer Function of LOL Rev. A | Page 13 of 20 1000 fVCO ERROR (ppm) 03877-0-018 REFSEL 1 1 1 1 0 Value –40°C to +85°C >3.0 µF <80 nA >6.3 V ADN2807 ADN2807 PIN + 0 QUANTIZER NIN CDR 50Ω 50Ω VREF 1 FROM QUANTIZER OUTPUT 1 50Ω RETIMED DATA CLK 0 50Ω TDINP/N LOOPEN BYPASS DATAOUTP/N CLKOUTP/N SQUELCH 03877-0-019 VCC Figure 19. Test Modes SQUELCH MODE When the squelch input is driven to a TTL high state, both the clock and data outputs are set to the zero state to suppress downstream processing. If desired, this pin can be directly driven by the LOS (loss-of-signal) detector output (SDOUT). If the squelch function is not required, the pin should be tied to VEE. TEST MODES—BYPASS AND LOOP-BACK When the bypass input is driven to a TTL high state, the quantizer output is connected directly to the buffers driving the data out pins, thus bypassing the clock recovery circuit (Figure 19). This feature can help the system to deal with nonstandard bit rates. The loopback mode can be invoked by driving the LOOPEN pin to a TTL high state, which facilitates system diagnostic testing. This will connect the test inputs (TDINP/N) to the clock and data recovery circuit (per Figure 19). The test inputs have internal 50 Ω terminations and can be left floating when not in use. TDINP/N are CML inputs and can be dc-coupled only when being driven by CML outputs. The TDINP/N inputs must be ac-coupled if driven by anything other than CML outputs. Bypass and loop-back modes are mutually exclusive; only one of these modes can be used at any given time. The ADN2807 is put into an indeterminate state if both BYPASS and LOOPEN pins are set to Logic 1 at the same time. Rev. A | Page 14 of 20 ADN2807 APPLICATION INFORMATION PCB DESIGN GUIDELINES Proper RF PCB design techniques must be used for optimal performance. Power Supply Connections and Ground Planes Use of one low impedance ground plane to both analog and digital grounds is recommended. The VEE pins should be soldered directly to the ground plane to reduce series inductance. If the ground plane is an internal plane and connections to the ground plane are made through vias, multiple vias may be used in parallel to reduce the series inductance, especially on Pins 33 and 34, which are the ground returns for the output buffers. Use of a 10 µF electrolytic capacitor between VCC and GND is recommended at the location where the 3.3 V supply enters the PCB. Use of 0.1 µF and 1 nF ceramic chip capacitors should be placed between IC power supply VCC and GND as close as possible to the ADN2807’s VCC pins. Again, if connections to the supply and ground are made through vias, the use of multiple vias in parallel will help to reduce series inductance, especially on Pins 35 and 36, which supply power to the high speed CLKOUTP/N and DATAOUTP/N output buffers. Refer to the schematic in Figure 20 for recommended connections. Transmission Lines Use of 50 Ω transmission lines are required for all high frequency input and output signals to minimize reflections, including PIN, NIN, CLKOUTP, CLKOUTN, DATAOUTP, and DATAOUTN (also REFCLKP/N for a 155.52 MHz REFCLK). It is also recommended that the PIN/NIN input traces are matched in length and that the CLKOUTP/N and DATAOUTP/N traces are matched in length. All high speed CML outputs, CLKOUTP/N and DATAOUTP/N, also require 100 Ω back termination chip resistors connected between the output pin and VCC. These resistors should be placed as close as possible to the output pins. These 100 Ω resistors are in parallel with on-chip 100 Ω termination resistors to create a 50 Ω back termination (Figure 21). The high speed inputs, PIN and NIN, are internally terminated with 50 Ω to an internal reference voltage (Figure 22). A 0.1 µF capacitor is recommended between VREF (Pin 4) and GND to provide an ac ground for the inputs. As with any high speed mixed-signal design, care should be taken to keep all high speed digital traces away from sensitive analog nodes. Soldering Guidelines for Chip Scale Package The leads on the 48-lead LFCSP are rectangular. The printed circuit board pad for these should be 0.1 mm longer than the package lead length and 0.05 mm wider than the package lead width. The land should be centered on the pad. This ensures that solder joint size is maximized. The bottom of the LFCSP has a central exposed pad. The pad on the printed circuit board should be at least as large as this exposed pad. The user must connect the exposed pad to analog VCC. If vias are used, they should be incorporated into the pad at 1.2 mm pitch grid. The via diameter should be between 0.3 mm and 0.33 mm, and the via barrel should be plated with 1 oz. copper to plug the via. Rev. A | Page 15 of 20 ADN2807 VCC 50Ω TRANSMISSION LINES 4 × 100Ω CLKOUTP VCC CLKOUTN µC DATAOUTP 10µF 1nF DATAOUTN DATAOUTP SQUELCH CLKOUTN CLKOUTP VEE VEE BYPASS SDOUT VCC VEE DATAOUTN LOOPEN 0.1µF 48 47 46 45 44 43 42 41 40 39 38 37 RTH THRADJ VCC VCC 1nF 0.1µF 0.1µF VEE VREF 50Ω PIN TIA NIN 50Ω SLICEP CIN VCC SLICEN VEE LOL µC XO1 19.44MHz XO2 1 36 2 35 3 34 4 33 EXPOSED PAD TIED OFF TO VCC PLANE WITH VIAS 5 6 32 31 7 30 8 29 28 9 0.1µ F 1nF 10 11 27 26 ADN2807 25 12 VCC VCC VCC 0.1µF 1nF VEE VEE SEL0 µC NC NC SEL1 µC VEE VCC 0.1µF 1nF VEE VCC VCC CF2 4.7µF (SEE TABLE 8 FOR SPECS) µC REFSEL0 µC REFSEL1 VEE CF1 VCC VEE NC TDINN TDINP NC VEE REFSEL REFCLKP VCC NC REFCLKN 13 14 15 16 17 18 19 20 21 22 23 24 03877-0-020 VCC 0.1µF 1nF Figure 20. Typical Application Circuit VCC VCC ADN2807 VCC 50Ω CIN 50Ω CIN PIN VTERM 100Ω 100Ω 100Ω TIA 100Ω 0.1µ F 50Ω 0.1µ F 50Ω 50Ω 50Ω 50Ω 0.1µ F VREF 03877-0-022 VTERM 50Ω 03877-0-021 ADN2807 NIN Figure 22. AC-Coupled Input Configuration Figure 21. AC-Coupled Output Configuration Rev. A | Page 16 of 20 ADN2807 CHOOSING AC COUPLING CAPACITORS LOL TOGGLING DURING LOSS OF INPUT DATA The ac coupling capacitors at the input (PIN, NIN) and output (DATAOUTP, DATAOUTN) of the ADN2807 must be chosen so that the device works properly at both OC-3 and OC-12 data rates. When choosing the capacitors, the time constant formed with the two 50 Ω resistors in the signal path must be considered. When a large number of consecutive identical digits (CIDs) are applied, the capacitor voltage can drop due to baseline wander (Figure 23), causing pattern dependent jitter (PDJ). For the ADN2807 to work robustly at both OC-3 and OC-12, a minimum capacitor of 0.1 µF to PIN/NIN and 0.1 µF on DATAOUTP/DATAOUTN should be used. This is based on the assumption that 1000 CIDs must be tolerated, and that the PDJ should be limited to 0.01 UI p-p. If the input data stream is lost due to a break in the optical link (or for any reason), the clock output from the ADN2807 stays within 1000 ppm of the VCO center frequency as long as there is a valid reference clock. The LOL pin will toggle at a rate of several kHz. This is because the LOL pin will toggle between a Logic 1 and Logic 0 while the frequency loop and phase loop swap control of the VCO. The chain of events is as follows: DC-COUPLED APPLICATION The inputs to the ADN2807 can also be dc-coupled. This may be necessary in burst mode applications where there are long periods of CIDs, and where baseline wander cannot be tolerated. If the inputs to the ADN2807 are dc-coupled, care must be taken not to violate the input range and common-mode level requirements of the ADN2807 (Figure 24 to Figure 26). If dc coupling is required and the output levels of the TIA do not adhere to the levels shown in Figure 25 and Figure 26, there must be level shifting and/or an attenuator between the TIA outputs and the ADN2807 inputs. V1 The ADN2807 is locked to the input data stream; LOL = 0. • The input data stream is lost due to a break in the link. The VCO frequency drifts until the frequency error is greater than 1000 ppm. LOL is asserted to a Logic 1 as control of the VCO is passed back to the frequency loop. • The frequency loop pulls the VCO to within 500 ppm of its center frequency. Control of the VCO is passed back to the phase loop and LOL is deasserted to Logic 0. • The phase loop tries to acquire, but there is no input data present so the VCO frequency drifts. • The VCO frequency drifts until the frequency error is greater than 1000 ppm. LOL is asserted to a Logic 1 as control of the VCO is passed back to the frequency loop. This process is repeated until a valid input data stream is re-established. ADN2807 CIN V2 PIN TIA CIN V2b COUT + 50Ω VREF V1b • DATAOUTP LIMAMP CDR COUT 50Ω DATAOUTN NIN 1 2 3 4 V1 V1b V2 VREF V2b VTH VDIFF NOTES 1. DURING DATA PATTERNS WITH HIGH TRANSITION DENSITY, DIFFERENTIAL DC VOLTAGE AT V1 AND V2 IS 0. 2. WHEN THE OUTPUT OF THE TIA GOES TO CID, V1 AND V1b ARE DRIVEN TO DIFFERENT DC LEVELS. V2 AND V2b DISCHARGE TO THE V REF LEVEL, WHICH EFFECTIVELY INTRODUCES A DIFFERENTIAL DC OFFSET ACROSS THE AC COUPLING CAPACITORS. 3. WHEN THE BURST OF DATA STARTS AGAIN,THE DIFFERENTIAL DC OFFSET ACROSS THE AC COUPLING CAPACITORS IS APPLIED TO THE INPUT LEVELS, CAUSING A DC SHIFT IN THE DIFFERENTIAL INPUT. THIS SHIFT IS LARGE ENOUGH SUCH THAT ONE OF THE STATES, EITHER HIGH OR LOW DEPENDING ON THE LEVELS OF V1 AND V1b WHEN THE TIA WENT TO CID, IS CANCELLED OUT. THE QUANTIZER WILL NOT RECOGNIZE THIS AS A VALID STATE. 4. THE DC OFFSET SLOWLY DISCHARGES UNTIL THE DIFFERENTIAL INPUT VOLTAGE EXCEEDS THE SENSITIVITY OF THE ADN2807. THE QUANTIZER WILL BE ABLE TO RECOGNIZE BOTH HIGH AND LOW STATES AT THIS POINT. Figure 23. Example of Baseline Wander Rev. A | Page 17 of 20 03877-0-023 VDIFF = V2–V2b VTH = ADN2807 QUANTIZER THRESHOLD ADN2807 INPUT (V) VCC ADN2807 V p-p = PIN – NIN = 2 × VSE = 2.4V MAX PIN 50Ω TIA 50Ω PIN VSE = 1.2V MAX NIN 50Ω NIN VREF 03877-0-024 0.1µ F 50Ω Figure 26. Maximum Allowed DC-Coupled Input Levels Figure 24. ADN2807 with DC-Coupled Inputs INPUT (V) V p-p = PIN – NIN = 2 × VSE = 10mV AT SENSITIVITY NIN VSE = 5mV MIN VCM = 0.4V MIN (DC-COUPLED) 03877-0-025 PIN Figure 25. Minimum Allowed DC-Coupled Input Levels Rev. A | Page 18 of 20 03877-0-026 VCM = 0.6V (DC-COUPLED) ADN2807 OUTLINE DIMENSIONS 7.00 BSC SQ 0.60 MAX 0.60 MAX 37 36 PIN 1 INDICATOR 6.75 BSC SQ TOP VIEW 0.30 0.23 0.18 PIN 1 INDICATOR 48 1 5.25 5.10 SQ 4.95 BOTTOM VIEW 0.50 0.40 0.30 25 24 12 13 0.25 MIN 1.00 0.85 0.80 5.50 REF 0.80 MAX 0.65 TYP MAX 12° 0.05 MAX 0.02 NOM 0.50 BSC SEATING PLANE 0.20 REF COPLANARITY 0.08 COMPLIANT TO JEDEC STANDARDS MO-220-VKKD-2 Figure 27. 48-Lead Lead Frame Chip Scale Package [LFCSP] 7 mm × 7 mm Body (CP-48) Dimensions shown in millimeters ORDERING GUIDE Model ADN2807ACP ADN2807ACP-RL Temperature Range –40°C to +85°C –40°C to +85°C Package Description 48-Lead LFCSP 48-Lead LFCSP Rev. A | Page 19 of 20 Package Option CP-48 CP-48 ADN2807 NOTES © 2004 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D03877–0–5/04(A) Rev. A | Page 20 of 20