CY62126EV30 MoBL® 1-Mbit (64 K × 16) Static RAM 1-Mbit (64 K × 16) Static RAM Features Functional Description ■ High speed: 45 ns The CY62126EV30 is a high performance CMOS static RAM organized as 64K words by 16 bits. This device features advanced circuit design to provide ultra low active current. This is ideal for providing More Battery Life (MoBL®) in portable applications such as cellular telephones. The device also has an automatic power down feature that significantly reduces power consumption when addresses are not toggling. Placing the device in standby mode reduces power consumption by more than 99 percent when deselected (CE HIGH). The input and output pins (I/O0 through I/O15) are placed in a high impedance state when the device is deselected (CE HIGH), the outputs are disabled (OE HIGH), both Byte High Enable and Byte Low Enable are disabled (BHE, BLE HIGH) or during a write operation (CE LOW and WE LOW). ■ Temperature ranges ❐ Industrial: –40 °C to +85 °C ❐ Automotive: –40 °C to +125 °C ■ Wide voltage range: 2.2 V to 3.6 V ■ Pin compatible with CY62126DV30 ■ Ultra low standby power ❐ Typical standby current: 1 A ❐ Maximum standby current: 4 A ■ Ultra low active power ❐ Typical active current: 1.3 mA at f = 1 MHz ■ Easy memory expansion with CE and OE features ■ Automatic power down when deselected ■ Complementary metal oxide semiconductor (CMOS) for optimum speed and power ■ Offered in Pb-free 48-ball very fine-pitch ball grid array (VFBGA) and 44-pin thin small outline package (TSOP) II packages To write to the device, take Chip Enable (CE) and Write Enable (WE) inputs LOW. If Byte Low Enable (BLE) is LOW, then data from I/O pins (I/O0 through I/O7) is written into the location specified on the address pins (A0 through A15). If Byte High Enable (BHE) is LOW, then data from I/O pins (I/O8 through I/O15) is written into the location specified on the address pins (A0 through A15). To read from the device, take Chip Enable (CE) and Output Enable (OE) LOW while forcing the Write Enable (WE) HIGH. If Byte Low Enable (BLE) is LOW, then data from the memory location specified by the address pins appear on I/O0 to I/O7. If Byte High Enable (BHE) is LOW, then data from memory appears on I/O8 to I/O15. See the Truth Table on page 11 for a complete description of read and write modes. Logic Block Diagram 64K x 16 RAM Array SENSE AMPS A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 ROW DECODER DATA IN DRIVERS I/O0–I/O7 I/O8–I/O15 • A13 BHE WE CE OE BLE A14 A15 A 11 Cypress Semiconductor Corporation Document Number: 38-05486 Rev. *I A12 COLUMN DECODER 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised May 31, 2011 [+] Feedback CY62126EV30 MoBL® Contents Pin Configuration .............................................................3 Product Portfolio ..............................................................3 Maximum Ratings .............................................................4 Operating Range ...............................................................4 Electrical Characteristics .................................................4 Capacitance ......................................................................5 Thermal Resistance ..........................................................5 Data Retention Characteristics .......................................6 Switching Characteristics ................................................7 Switching Waveforms ......................................................8 Read Cycle No. 1 (Address transition controlled) .......8 Read Cycle No. 2 (OE controlled) ...............................8 Write Cycle No. 1 (WE controlled) ...............................9 Write Cycle No. 2 (CE controlled) ...............................9 Write Cycle No. 3 (WE controlled, OE LOW .............10 Document Number: 38-05486 Rev. *I Write Cycle No. 4 (BHE/BLE controlled, OE LOW) .......................................10 Truth Table ......................................................................11 Ordering Information ......................................................12 Ordering Code Definitions .........................................12 Package Diagrams ..........................................................13 Acronyms ........................................................................15 Document Conventions .................................................15 Units of Measure .......................................................15 Document History Page .................................................16 Sales, Solutions, and Legal Information ......................18 Worldwide Sales and Design Support .......................18 Products ....................................................................18 PSoC Solutions .........................................................18 Page 2 of 18 [+] Feedback CY62126EV30 MoBL® Pin Configuration Figure 2. 44-pin TSOP II (Top View) [1] Figure 1. 48-ball VFBGA (Top View) 1 2 3 4 5 6 BLE OE A0 A1 A2 NC A I/O8 BHE A3 A4 CE I/O0 B I/O9 I/O10 A5 A6 I/O1 I/O2 C VSS I/O11 NC A7 I/O3 Vcc D VCC I/O12 NC NC I/O4 Vss E I/O14 I/O13 A14 A15 I/O5 I/O6 F I/O15 NC A12 A13 WE I/O7 G NC A8 A9 A10 A11 NC H A4 A3 A2 A1 A0 CE I/O0 I/O1 I/O2 I/O3 VCC VSS I/O4 I/O5 I/O6 I/O7 WE A15 A14 A13 A12 NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 A5 A6 A7 OE BHE BLE I/O15 I/O14 I/O13 I/O12 VSS VCC I/O11 I/O10 I/O9 I/O8 NC A8 A9 A10 A11 NC Product Portfolio Power Dissipation Product CY62126EV30LL VCC Range (V) Range Industrial CY62126EV30LL Automotive Speed (ns) Min Typ[2] Max 2.2 3.0 3.6 2.2 3.0 3.6 Operating, ICC (mA) f = 1 MHz f = fmax Standby, ISB2 (A) Typ[2] Max Typ[2] Max Typ[2] Max 45 1.3 2 11 16 1 4 55 1.3 4 11 35 1 30 Notes 1. NC pins are not connected on the die. 2. Typical values are included for reference only and are not guaranteed or tested. Typical values are measured at VCC = VCC(typ), TA = 25 °C. Document Number: 38-05486 Rev. *I Page 3 of 18 [+] Feedback CY62126EV30 MoBL® DC input voltage[3, 4] 0.3 V to 3.6 V (VCCmax + 0.3 V) Maximum Ratings Exceeding maximum ratings may shorten the battery life of the device. These user guidelines are not tested. Storage temperature ................................ –65 °C to +150 °C Ambient temperature with power applied .......................................... –55 °C to +125 °C Supply voltage to ground potential .............................–0.3 V to 3.6 V (VCCmax + 0.3 V) Output current into outputs (LOW) ..............................20 mA Static discharge voltage ......................................... > 2001 V (MIL-STD-883, Method 3015) Latch up current .................................................... > 200 mA Operating Range DC voltage applied to outputs in High Z state[3, 4] ..............–0.3 V to 3.6 V (VCCmax + 0.3 V) Device Range CY62126EV30LL Industrial Ambient Temperature VCC[5] –40 °C to +85 °C 2.2 V to 3.6 V Automotive –40 °C to +125 °C Electrical Characteristics Over the Operating Range Parameter Description Test Conditions 45 ns (Industrial) 55 ns (Automotive) Min Typ[6] Max Min Typ[6] – 2.0 – – VOH Output high voltage IOH = –0.1 mA 2.0 – IOH = –1.0 mA, VCC > 2.70 V 2.4 – – 2.4 VOL Output low voltage IOL = 0.1 mA – – 0.4 – IOL = 2.1 mA, VCC > 2.70 V – – 0.4 – 1.8 – VCC + 0.3 1.8 Max Unit – V – V 0.4 V – 0.4 V – VCC + 0.3 V VIH Input high voltage VCC = 2.2 V to 2.7 V VCC = 2.7 V to 3.6 V 2.2 – VCC + 0.3 2.2 – VCC + 0.3 V VIL Input low voltage VCC = 2.2 V to 2.7 V –0.3 – 0.6 –0.3 – 0.6 V VCC = 2.7 V to 3.6 V –0.3 – 0.8 –0.3 – 0.8 V –1 – +1 –4 – +4 A IIX Input leakage current GND < VI < VCC IOZ Output leakage current GND < VO < VCC, Output Disabled –1 – +1 –4 – +4 A ICC VCC operating supply current f = fmax = 1/tRC VCC = VCCmax IOUT = 0 mA f = 1 MHz CMOS levels – 11 16 – 11 35 mA – 1.3 2.0 – 1.3 4.0 ISB1[7] Automatic CE power down current —CMOS inputs CE > VCC 0.2 V, VIN > VCC – 0.2 V, VIN < 0.2 V, f = fmax (Address and Data Only), f = 0 (OE, BHE, BLE and WE), VCC = 3.60 V – 1 4 – 1 35 A ISB2 [7] Automatic CE power down current —CMOS inputs CE > VCC – 0.2 V, VIN > VCC – 0.2 V or VIN < 0.2 V, f = 0, VCC = 3.60 V – 1 4 – 1 30 A Notes 3. VIL(min) = –2.0 V for pulse durations less than 20 ns. 4. VIH(max) = VCC + 0.75 V for pulse durations less than 20 ns. 5. Full device AC operation assumes a 100 s ramp time from 0 to Vcc(min) and 200 s wait time after Vcc stabilization. 6. Typical values are included for reference only and are not guaranteed or tested. Typical values are measured at VCC = VCC(typ), TA = 25 °C. 7. Chip enable (CE) needs to be tied to CMOS levels to meet the ISB1 / ISB2 / ICCDR spec. Other inputs can be left floating. Document Number: 38-05486 Rev. *I Page 4 of 18 [+] Feedback CY62126EV30 MoBL® Capacitance Parameter [8] Description CIN Input capacitance COUT Output capacitance Test Conditions TA = 25 °C, f = 1 MHz, VCC = VCC(typ) Max 10 10 Unit pF pF Thermal Resistance Parameter [8] JA JC Description Thermal resistance (Junction to ambient) Thermal resistance (Junction to case) Test Conditions Still Air, soldered on a 4.25 × 1.125 inch, two-layer printed circuit board 48-ball VFBGA 44-pin TSOP II Unit Package Package 58.85 28.2 °C/W 17.01 3.4 °C/W Figure 3. AC Test Loads and Waveforms R1 V CC OUTPUT VCC 30 pF R2 INCLUDING JIG AND SCOPE 10% GND Rise Time = 1 V/ns ALL INPUT PULSES 90% 90% 10% Fall Time = 1 V/ns Equivalent to: THÉVENIN EQUIVALENT RTH OUTPUT VTH Parameters 2.2 V–2.7 V 2.7 V–3.6 V Unit R1 16600 1103 R2 15400 1554 RTH 8000 645 VTH 1.2 1.75 V Note 8. Tested initially and after any design or process changes that may affect these parameters. Document Number: 38-05486 Rev. *I Page 5 of 18 [+] Feedback CY62126EV30 MoBL® Data Retention Characteristics Over the Operating Range Parameter Min Typ[9] Max Unit 1.5 – – V Industrial – – 3 A Automotive – – 30 A 0 – – ns CY62126EV30LL-45 45 – – ns CY62126EV30LL-55 55 – – Conditions VCC for data retention VDR ICCDR tCDR Description [10] Data retention current [11] VCC= VDR, CE > VCC – 0.2 V, VIN > VCC – 0.2 V or VIN < 0.2 V Chip deselect to data retention time tR[12] Operation recovery time Figure 4. Data Retention Waveform VCC VCC(min) tCDR DATA RETENTION MODE VDR > 1.5 V VCC(min) tR CE Notes 9. Typical values are included for reference only and are not guaranteed or tested. Typical values are measured at VCC = VCC(typ), TA = 25 °C. 10. Chip enable (CE) needs to be tied to CMOS levels to meet the ISB1 / ISB2 / ICCDR spec. Other inputs can be left floating. 11. Tested initially and after any design or process changes that may affect these parameters. 12. Full device AC operation requires linear VCC ramp from VDR to VCC(min) > 100 s. Document Number: 38-05486 Rev. *I Page 6 of 18 [+] Feedback CY62126EV30 MoBL® Switching Characteristics Over the Operating Range Parameter [13, 14] Description 45 ns (Industrial) Min 55 ns (Automotive) Max Min Max Unit Read Cycle tRC Read cycle time 45 – 55 – ns tAA Address to data valid – 45 – 55 ns tOHA Data hold from address change 10 – 10 – ns tACE CE LOW to data valid – 45 – 55 ns tDOE OE LOW to data valid – 22 – 25 ns ns [15] tLZOE OE LOW to Low Z 5 – 5 – tHZOE OE HIGH to High Z [15, 16] – 18 – 20 ns tLZCE CE LOW to Low Z [15] 10 – 10 – ns – 18 – 20 ns ns tHZCE CE HIGH to High Z [15, 16] tPU CE LOW to power up 0 – 0 – tPD CE HIGH to power down – 45 – 55 ns tDBE BHE / BLE LOW to data valid – 22 – 25 ns [15] 5 tLZBE tHZBE BHE / BLE LOW to Low Z BHE / BLE HIGH to High Z [15, 16] – 5 – ns – 18 – 20 ns 45 – 55 – ns Write Cycle [17] tWC Write cycle time tSCE CE LOW to write end 35 – 40 – ns tAW Address setup to write end 35 – 40 – ns tHA Address hold from write end 0 – 0 – ns tSA Address setup to write start 0 – 0 – ns tPWE WE pulse width 35 – 40 – ns ns tBW BHE / BLE pulse width 35 – 40 – tSD Data setup to write end 25 – 25 – ns tHD Data hold from write end 0 – 0 – ns – 18 – 20 ns 10 – 10 – ns tHZWE tLZWE WE LOW to High Z [15, 16] WE HIGH to Low Z [15] Notes 13. Test conditions assume signal transition time of 3 ns or less, timing reference levels of VCC(typ)/2, input pulse levels of 0 to VCC(typ), and output loading of the specified IOL/IOH and 30-pF load capacitance. 14. AC timing parameters are subject to byte enable signals (BHE or BLE) not switching when chip is disabled. See application note AN13842 for further clarification. 15. At any temperature and voltage condition, tHZCE is less than tLZCE, tHZBE is less than tLZBE, tHZOE is less than tLZOE, and tHZWE is less than tLZWE for any device. 16. tHZOE, tHZCE, tHZBE, and tHZWE transitions are measured when the outputs enter a high impedance state. 17. The internal write time of the memory is defined by the overlap of WE, CE = VIL, BHE, BLE or both = VIL. All signals must be active to initiate a write and any of these signals can terminate a write by going inactive. The data input setup and hold timing must refer to the edge of signal that terminates write. Document Number: 38-05486 Rev. *I Page 7 of 18 [+] Feedback CY62126EV30 MoBL® Switching Waveforms Read Cycle No. 1 (Address transition controlled) [18, 19] tRC ADDRESS tOHA DATA OUT tAA PREVIOUS DATA VALID DATA VALID Read Cycle No. 2 (OE controlled) [19, 20] ADDRESS tRC CE tPD tHZCE tACE OE tHZOE tDOE tLZOE BHE/BLE tHZBE tDBE tLZBE DATA OUT HIGHIMPEDANCE HIGH IMPEDANCE DATA VALID tLZCE tPU VCC SUPPLY CURRENT 50% 50% ICC ISB Notes 18. The device is continuously selected. OE, CE = VIL, BHE, BLE, or both = VIL. 19. WE is high for read cycle. 20. Address valid before or similar to CE and BHE, BLE transition LOW. Document Number: 38-05486 Rev. *I Page 8 of 18 [+] Feedback CY62126EV30 MoBL® Switching Waveforms (continued) Write Cycle No. 1 (WE controlled) [21, 22, 23] tWC ADDRESS tSCE CE tAW tHA tSA tPWE WE tBW BHE/BLE OE DATA I/O tSD NOTE 24 tHD DATAIN tHZOE Write Cycle No. 2 (CE controlled) [21, 22, 23] tWC ADDRESS tSCE CE tSA tAW tHA tPWE WE tBW BHE/BLE OE tSD DATA I/O tHD DATAIN NOTE 24 tHZOE Notes 21. The internal write time of the memory is defined by the overlap of WE, CE = VIL, BHE, BLE or both = VIL. All signals must be active to initiate a write and any of these signals can terminate a write by going inactive. The data input setup and hold timing must refer to the edge of signal that terminates write. 22. Data I/O is high impedance if OE = VIH. 23. If CE goes high simultaneously with WE = VIH, the output remains in a high impedance state. 24. During this period, the I/Os are in output state. Do not apply input signals. Document Number: 38-05486 Rev. *I Page 9 of 18 [+] Feedback CY62126EV30 MoBL® Switching Waveforms (continued) Write Cycle No. 3 (WE controlled, OE LOW [25] tWC ADDRESS tSCE CE tBW BHE/BLE tAW tHA tSA WE tPWE tSD DATA I/O NOTE 26 tHD DATAIN tLZWE tHZWE Write Cycle No. 4 (BHE/BLE controlled, OE LOW) [25] tWC ADDRESS CE tSCE tAW tHA tBW BHE/BLE tSA tPWE WE tHZWE DATA I/O NOTE 26 tSD tHD DATAIN tLZWE Notes 25. If CE goes high simultaneously with WE = VIH, the output remains in a high impedance state. 26. During this period, the I/Os are in output state. Do not apply input signals. Document Number: 38-05486 Rev. *I Page 10 of 18 [+] Feedback CY62126EV30 MoBL® Truth Table CE[27] WE OE BHE BLE H X X X X L X X H L H L L L H L L H L L H L H L Inputs/Outputs Mode Power High Z Deselect/power down Standby (ISB) H High Z Output disabled Active (ICC) L Data out (I/O0–I/O15) Read Active (ICC) H L Data out (I/O0–I/O7); I/O8–I/O15 in High Z Read Active (ICC) L H Data out (I/O8–I/O15); I/O0–I/O7 in High Z Read Active (ICC) H L L High Z Output disabled Active (ICC) H H L High Z Output disabled Active (ICC) H H L H High Z Output disabled Active (ICC) L L X L L Data in (I/O0–I/O15) Write Active (ICC) L L X H L Data in (I/O0–I/O7); I/O8–I/O15 in High Z Write Active (ICC) L L X L H Data in (I/O8–I/O15); I/O0–I/O7 in High Z Write Active (ICC) Note 27. Chip enable must be at CMOS levels (not floating). Intermediate voltage levels on this pin is not permitted. Document Number: 38-05486 Rev. *I Page 11 of 18 [+] Feedback CY62126EV30 MoBL® Ordering Information Speed (ns) 45 55 Ordering Code CY62126EV30LL-45BVXI Package Diagram Package Type 51-85150 48-ball VFBGA (Pb-free) Operating Range Industrial CY62126EV30LL-45ZSXI 51-85087 44-pin TSOP II (Pb-free) Industrial CY62126EV30LL-45ZSXA 51-85087 44-pin TSOP II (Pb-free) Automotive-A CY62126EV30LL-55BVXE 51-85150 48-ball VFBGA (Pb-free) Automotive-E CY62126EV30LL-55ZSXE 51-85087 44-pin TSOP II (Pb-free) Automotive-E Contact your local Cypress sales representative for availability of other parts. Ordering Code Definitions CY 621 2 6 E V30 LL - XX XX X X Temperature Range: X = I or A or E I = Industrial; A = Automotive-A; E = Automotive-E Pb-free Package Type: XX = BV or ZS BV = 48-ball VFBGA ZS = 44-pin TSOP II Speed Grade: XX = 45 ns or 55 ns Low Power Voltage: 3 V Typical E = Process Technology 90 nm Buswidth = × 16 Density = 1-Mbit Family Code: MoBL SRAM family Company ID: CY = Cypress Document Number: 38-05486 Rev. *I Page 12 of 18 [+] Feedback CY62126EV30 MoBL® Package Diagrams Figure 5. 48-ball VFBGA (6 × 8 × 1 mm) BV48/BZ48, 51-85150 51-85150 *F Document Number: 38-05486 Rev. *I Page 13 of 18 [+] Feedback CY62126EV30 MoBL® Package Diagrams (continued) Figure 6. 44-pin TSOP Z44-II, 51-85087 51-85087 *C Document Number: 38-05486 Rev. *I Page 14 of 18 [+] Feedback CY62126EV30 MoBL® Acronyms Document Conventions Acronym Description Units of Measure CE chip enable CMOS complementary metal oxide semiconductor °C degree Celcius I/O input/output MHz Mega Hertz OE output enable μA micro Amperes RAM random access memory μs micro seconds SRAM static random access memory mA milli Amperes TSOP thin small outline package mm milli meter VFBGA very fine-pitch ball grid array ns nano seconds WE write enable ohms % percent pF pico Farad V Volts W Watts Document Number: 38-05486 Rev. *I Symbol Unit of Measure Page 15 of 18 [+] Feedback CY62126EV30 MoBL® Document History Page Document Title: CY62126EV30 MoBL®, 1-Mbit (64 K × 16) Static RAM Document Number: 38-05486 Orig. of Rev. ECN No. Submission Description of Change Date Change ** 202760 See ECN AJU New data sheet *A 300835 See ECN SYT Converted from Advance Information to Preliminary Specified Typical standby power in the Features Section Changed E3 ball from DNU to NC in the Pin Configuration for the FBGA Package and removed the footnote associated with it on page #2 Changed tOHA from 6 ns to 10 ns for both 35- and 45-ns speed bins, respectively Changed tDOE, tSD from 15 to 18 ns for 35-ns speed bin Changed tHZOE, tHZBE, tHZWE from 12 and 15 ns to 15 and 18 ns for the 35- and 45-ns speed bins, respectively Changed tHZCE from 12 and 15 ns to 18 and 22 ns for the 35- and 45-ns speed bins, respectively Changed tSCE,tBW from 25 and 40 ns to 30 and 35 ns for the 35- and 45-ns speed bins, respectively Changed tAW from 25 to 30 ns and 40 to 35 ns for 35 and 45-ns speed bins respectively Changed tDBE from 35 and 45 ns to 18 and 22 ns for the 35 and 45 ns speed bins respectively Removed footnote that read “BHE.BLE is the AND of both BHE and BLE. Chip can be deselected by either disabling the chip enable signals or by disabling both BHE and BLE” on page # 4 Removed footnote that read “If both BHE and BLE are toggled together, then tLZBE is 10 ns” on page # 5 Added Pb-free package information *B 461631 See ECN NXR Converted from Preliminary to Final Removed 35 ns Speed Bin Removed “L” version of CY62126EV30 Changed ICC (Typ) from 8 mA to 11 mA and ICC (max) from 12 mA to 16 mA for f = fmax Changed ICC (max) from 1.5 mA to 2.0 mA for f = 1 MHz, ISB1, ISB2 (max) from 1 A to 4 A, ISB1, ISB2 (Typ) from 0.5 A to 1 A, ICCDR (max) from 1.5 A to 3 A, AC Test load Capacitance value from 50 pF to 30 pF, tLZOE from 3 to 5 ns, tLZCE from 6 to 10 ns, tHZCE from 22 to 18 ns, tLZBE from 6 to 5 ns, tPWE from 30 to 35 ns, tSD from 22 to 25 ns, tLZWE from 6 to 10 ns, and updated the Ordering Information table. *C 925501 See ECN VKN Added footnote #7 related to ISB2 and ICCDR Added footnote #11 related AC timing parameters *D 1045260 See ECN VKN Added Automotive information Updated Ordering Information table *E 2631771 01/07/09 NXR/PYRS Changed CE condition from X to L in Truth table for Output Disable mode Updated template *F 2944332 06/04/2010 VKN Added Contents Removed byte enable from footnote #2 in Electrical Characteristics Added footnote related to chip enable in Truth Table Updated Package Diagrams Updated links in Sales, Solutions, and Legal Information *G 2996166 07/29/2010 AJU Added CY62126EV30LL-45ZSXA part in Ordering Information. Added Ordering Code Definitions. Modified table footnote format. *H 3113864 12/17/2010 PRAS Updated Figure 1 and Package Diagram, and fixed Typo in Figure 3.. Document Number: 38-05486 Rev. *I Page 16 of 18 [+] Feedback CY62126EV30 MoBL® Document History Page (continued) Document Title: CY62126EV30 MoBL®, 1-Mbit (64 K × 16) Static RAM Document Number: 38-05486 Orig. of Rev. ECN No. Submission Description of Change Date Change *I 3270487 05/31/2011 RAME Updated Functional Description (Removed “For best practice recommendations, refer to the Cypress application note AN1064, SRAM System Guidelines.”). Updated Electrical Characteristics. Updated Data Retention Characteristics. Added Acronyms and Units of Measure. Updated in new template. Document Number: 38-05486 Rev. *I Page 17 of 18 [+] Feedback CY62126EV30 MoBL® Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. Products Automotive PSoC Solutions cypress.com/go/automotive psoc.cypress.com/solutions cypress.com/go/clocks PSoC 1 | PSoC 3 | PSoC 5 Clocks & Buffers Interface Lighting & Power Control cypress.com/go/interface cypress.com/go/powerpsoc cypress.com/go/plc Memory cypress.com/go/memory Optical & Image Sensing cypress.com/go/image PSoC cypress.com/go/psoc Touch Sensing cypress.com/go/touch USB Controllers cypress.com/go/USB Wireless/RF cypress.com/go/wireless © Cypress Semiconductor Corporation, 2004-2011. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document Number: 38-05486 Rev. *I Revised May 31, 2011 Page 18 of 18 MoBL is a registered trademark, and More Battery Life is a trademark, of Cypress Semiconductor. All products and company names mentioned in this document may be the trademarks of their respective holders. [+] Feedback