White Electronic Designs W3DG72128V-D2 PRELIMINARY* 1GB- 128Mx72 SDRAM, REGISTER and SPD, w/PLL FEATURES DESCRIPTION Clock speed of 100MHz and 133MHz Burst Mode Operation Auto and Self Refresh capability LVTTL compatible inputs and outputs Serial Presence Detect with EEPROM The W3DG72128V is a 128Mx72 synchronous DRAM module which consists of eighteen 128Mx4 stack SDRAM components in TSOP II package, two 18 bit Drive ICs for input control signal and one 2Kb EEPROM in an 8 pin TSSOP package for Serial Presence Detect which are mounted on a 168 pin DIMM multilayer FR4 Substrate. Fully synchronous: All signals are registered on the positive edge of the system clock Programmable Burst Lengths: 1, 2, 4, 8 or Full Page 3.3V ± 0.3V Power Supply 168 Pin DIMM JEDEC * This product is under development, is not qualified or characterized and is subject to change without notice. Pin ConfigurATIONs (FRONT SIDE/BACK SIDE) Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Front VSS DQ0 DQ1 DQ2 DQ3 VCC DQ4 DQ5 DQ6 DQ7 DQ8 VSS DQ9 DQ10 DQ11 DQ12 DQ13 VCC DQ14 DQ15 CB0 CB1 VSS NC NC VCC WE# DQM0 Pin 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 Front DQM1 CS0# DNU VSS A0 A2 A4 A6 A8 A10/AP BA1 VCC VCC CLK0 VSS DNU CS2# DQM2 DQM3 DNU VCC NC NC CB2 CB3 VSS DQ16 DQ17 Pin 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 Front DQ18 DQ19 VCC DQ20 NC *VREF *CKE1 VSS DQ21 DQ22 DQ23 VSS DQ24 DQ25 DQ26 DQ27 VCC DQ28 DQ29 DQ30 DQ31 VSS CLK2 NC NC **SDA **SCL VCC Pin 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 Back VSS DQ32 DQ33 DQ34 DQ35 VCC DQ36 DQ37 DQ38 DQ39 DQ40 VSS DQ41 DQ42 DQ43 DQ44 DQ45 VCC DQ46 DQ47 CB4 CB5 VSS NC NC VCC CAS# DQM4 Pin 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 Back DQM5 *CS1# RAS# VSS A1 A3 A5 A7 A9 BA0 A11 VCC *CLK1 *A12 VSS CKE0 *CS3# DQM6 DQM7 *A13 VCC NC NC CB6 CB7 VSS DQ48 DQ49 Pin 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 PIN NAMES Back DQ50 DQ51 VCC DQ52 NC *VREF REGE VSS DQ53 DQ54 DQ55 VSS DQ56 DQ57 DQ58 DQ59 VCC DQ60 DQ61 DQ62 DQ63 VSS *CLK3 NC **SA0 **SA1 **SA2 VCC A0 – A12 BA0-1 DQ0-63 CB0-7 CLK0 CKE0 CS0#,CS2# RAS# CAS# WE# DQM0-7 VCC VSS *VREF REGE SDA SCL SA0-2 DNU NC Address input (Multiplexed) Select Bank Data Input/Output Check bit (Data-in/data-out) Clock input Clock Enable input Chip select Input Row Address Strobe Column Address Strobe Write Enable DQM Power Supply (3.3V) Ground Power supply for reference Register Enable Serial data I/O Serial clock Address in EEPROM Do not use No Connect * These pins are not used in this module. ** These pins should be NC in the system which does not support SPD. White Electronic Designs Corp. reserves the right to change products or specifications without notice. August 2004 Rev. 1 1 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs W3DG72128V-D2 PRELIMINARY FUNCTIONAL BLOCK DIAGRAM CS1# CS0# DQMB0 # DQMB4 DQ0 DQ1 DQ2 DQ3 DQM CS I/O 0 I/O 1 D0 I/O 2 I/O 3 DQM CS I/O 0 I/O 1 D18 I/O 2 I/O 3 DQ32 DQ33 DQ34 DQ35 I/O 0 I/O 1 I/O 2 I/O 3 DQ4 DQ5 DQ6 DQ7 DQM CS I/O 0 I/O 1 D1 I/O 2 I/O 3 DQM CS I/O 0 I/O 1 D19 I/O 2 I/O 3 DQ36 DQ37 DQ38 DQ39 DQM CS I/O 0 I/O 1 D10 I/O 2 I/O 3 DQM CS DQM CS DQ8 DQ9 DQ10 DQ11 I/O 0 I/O 1 I/O 2 I/O 3 DQ12 DQ13 DQ14 DQ15 I/O 0 I/O 1 I/O 2 I/O 3 I/O 0 I/O 1 I/O 2 I/O 3 D2 D20 I/O 0 I/O 1 I/O 2 I/O 3 D3 D21 DQM CS I/O 0 I/O 1 D22 I/O 2 I/O 3 DQM CS I/O 0 I/O 1 D4 I/O 2 I/O 3 D27 DQM CS I/O 0 I/O 1 D28 I/O 2 I/O 3 I/O 0 I/O 1 I/O 2 I/O 3 DQM CS DQ44 DQ45 DQ46 DQ47 I/O 0 I/O 1 I/O 2 I/O 3 D11 I/O 0 I/O 1 I/O 2 I/O 3 DQM CS DQM CS CB4 CB5 CB6 CB7 D29 D12 DQM CS I/O 0 I/O 1 D13 I/O 2 I/O 3 I/O 0 I/O 1 I/O 2 I/O 3 D30 DQM CS I/O 0 I/O 1 D31 I/O 2 I/O 3 CS3# CS2# DQMB2 DQMB6 DQM CS DQM CS DQ16 DQ17 DQ18 DQ19 I/O 0 I/O 1 I/O 2 I/O 3 DQ20 DQ21 DQ22 DQ23 I/O 0 I/O 1 I/O 2 I/O 3 I/O 0 I/O 1 I/O 2 I/O 3 D5 D23 I/O 0 I/O 1 I/O 2 I/O 3 D6 D24 DQMB3 DQM CS DQM CS DQ48 DQ49 DQ50 DQ51 I/O 0 I/O 1 I/O 2 I/O 3 DQ52 DQ53 DQ54 DQ55 I/O 0 I/O 1 I/O 2 I/O 3 DQM CS DQM CS D14 I/O 0 I/O 1 I/O 2 I/O 3 SDRAM CK0 PLL REGISTER D32 12pF DQM CS DQM CS D15 I/O 0 I/O 1 I/O 2 I/O 3 D33 CK1-CK3 12pF DQMB7 DQM CS DQM CS I/O 0 I/O 1 I/O 2 I/O 3 I/O 0 I/O 1 I/O 2 I/O 3 D7 I/O 0 I/O 1 I/O 2 I/O 3 I/O 0 I/O 1 I/O 2 I/O 3 D8 CS0#-CS3# DQMB0 to DQMB7 BA0-BA1 A0-A12 RAS# CAS# CKE0 WE# D25 R E G I S T E R D26 DQM CS DQM CS DQ56 DQ57 DQ58 DQ59 DQM CS DQM CS DQ28 DQ29 DQ30 DQ31 D9 DQM CS DQ40 DQ41 DQ42 DQ43 DQM CS DQM CS DQ24 DQ25 DQ26 DQ27 I/O 0 I/O 1 I/O 2 I/O 3 DQMB5 DQMB1 CB0 CB1 CB2 CB3 DQM CS DQM CS I/O 0 I/O 1 I/O 2 I/O 3 D16 I/O 0 I/O 1 I/O 2 I/O 3 DQM CS DQ60 DQ61 DQ62 DQ63 I/O 0 I/O 1 I/O 2 I/O 3 SCL DQM CS D17 RS0-RS3 RDQMB0 - RDQMB7 BA0-BAN: SDRAMS D0-D35 RBA0 - RBAN A0-AN: SDRAMS D0-D35 RA0-RAN RAS#: SDRAMS D0 - D35 RRAS CAS#: SDRAMS D0 - D35 RCAS CKE: SDRAMS D0 - D35 RCKE0 RWE WE#: SDRAMS D0 - D35 SERIAL PD D34 I/O 0 I/O 1 I/O 2 I/O 3 SDA A0 A1 A2 SA0 SA1 SA2 D35 VCC D0 - D35 VSS D0 - D35 NOTE: DQ wiring may differ than described in this drawing, however DQ/DQMB/CKE/S relationships must be maintained as shown. REGE PCK # NOTE: ALL RESISTOR VALUES ARE 10 OHMS. White Electronic Designs Corp. reserves the right to change products or specifications without notice. August 2004 Rev. 1 2 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs W3DG72128V-D2 PRELIMINARY ABSOLUTE MAXIMUM RATINGS Parameter Symbol Value Units Voltage on any pin relative to VSS VIN, VOUT -1.0 ~ 4.6 V Voltage on VCC supply relative to VSS VCC, VCCQ -1.0 ~ 4.6 V °C TSTG -55 ~ +150 Power Dissipation PD 36 W Short Circuit Current IOS 50 mA Storage Temperature Note: Permanent device damage may occur if "ABSOLUTE MAXIMUM RATINGS" are exceeded. Functional operation should be restricted to recommended operating condition. Exposure to higher than recommended voltage for extended periods of time could affect device reliability. RECOMMENDED DC OPERATING CONDITIONS Voltage Referenced to: VSS = 0V, 0°C ≤ TA ≤ 70°C Parameter Symbol Min Typ Max Unit Supply Voltage VCC 3.0 3.3 3.6 V Input High Voltage VIH 2.0 3.0 VCCQ+0.3 V Note 1 Input Low Voltage VIL -0.3 — 0.8 V 2 Output High Voltage VOH 2.4 — — V IOH= -2mA Output Low Voltage VOL — — 0.4 V IOL= -2mA Input Leakage Current ILI -10 — 10 μA 3 Note: 1. VIH (max)= 5.6V AC. The overshoot voltage duration is ≤ 3ns. 2. VIL (min)= -2.0V AC. The undershoot voltage duration is ≤ 3ns. 3. Any input 0V ≤ VIN ≤ VCCQ Input leakage currents include Hi-Z output leakage for all bi-directional buffers with Tri-State outputs. CAPACITANCE TA = 25 °C, f = 1MHz, VCC = 3.3V, VREF = 1.4V ± 200mV Parameter Symbol Max Unit Input Capacitance (A0-A12) CIN1 74 pF Input Capacitance (RAS#,CAS#,WE#) CIN2 74 pF Input Capacitance (CKE0) CIN3 40 pF Input Capacitance (CLK0) CIN4 6 pF Input Capacitance (CS0#,CS2#) CIN5 40 pF Input Capacitance (DQM0-DQM7) CIN6 11 pF Input Capacitance (BA0-BA1) CIN7 74 pF Data input/output capacitance (DQ0-DQ63) COUT 15 pF Data input/output capacitance (CB0-CB7) COUT1 15 pF White Electronic Designs Corp. reserves the right to change products or specifications without notice. August 2004 Rev. 1 3 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs W3DG72128V-D2 PRELIMINARY OPERATING CURRENT CHARACTERISTICS VCC = 3.3V, 0°C ≤ TA ≤ 70°C Parameters Symbol Conditions Versions Units Note 2430 mA 1 133/100 Operating Current (One bank active) ICC1 Burst Length = 1 tRC ≥ tRC(min) IOL = 0mA Precharge Standby Current in Power Down Mode ICC2P CKE ≤ VIL(max), tCC = 10ns 36 mA 3 Active standby in current non powerdown mode ICC3N CKE ≥ VIH(min), CS ≥ VIH(min), tCC = 10ns Input signals are charged one time during 20ns 720 mA 3 Operating current (Burst mode) ICC4 Io = mA Page burst 4 Banks activated tCCD = 2CLK 2430 mA 1 Refresh current ICC5 tRC ≥ tRC(min) 5130 mA 2 Self refresh current ICC6 CKE ≤ 0.2V 63 mA 3 Notes: 1. Measured with outputs open. 2. Refresh period is 64ms. 3. Measured with 1 PLL & 2 Drive ICs. White Electronic Designs Corp. reserves the right to change products or specifications without notice. August 2004 Rev. 1 4 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs W3DG72128V-D2 PRELIMINARY ORDERING INFORMATION Part Number Speed CAS Latency Height* W3DG72128V10D2 100MHz CL=2 37.34 (1.470”) W3DG72128V7D2 133MHz CL=2 37.34 (1.470”) W3DG72128V75D2 133MHz CL=3 37.34 (1.470”) PACKAGE DIMENSIONS 6.48 (0.255) MAX. 133.35 (5.250) 3.18 (0.125) (2X) 3.99 (0.157 ± 0.004) (2X) 37.34 (1.470) 17.78 (0.700) (0.000) 3.10 (0.122) 8.89 (0.350) P1 11.43 (0.450) 36.83 (1.450) 54.61 (2.150) 6.35 (0.250) 15.60 (0.614) 6.35 (0.250) 57.79 (2.275) 3.99 (0.157) MIN. 12.70 ± 0.10 (0.050 ± 0.0039) (0.000) 115.57 (4.550) * ALL DIMENSIONS ARE IN MILLIMETERS AND (INCHES) White Electronic Designs Corp. reserves the right to change products or specifications without notice. August 2004 Rev. 1 5 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs W3DG72128V-D2 PRELIMINARY Document Title 1GB - 128Mx72 SDRAM, REGISTERED and SPD, w/PLL Revision History Rev # History Release Date Status Rev A Created Datasheet 10-25-01 Advanced B.1 Changed block diagram 1-17-02 Advanced Rev B B.2 Changed module height B.3 Add ordering information Rev C Changed module width from 0.150 to 0.255 3-25-02 Advanced Rev 0 Changed Advanced to Final 9-19-02 Final 1.1 Updated Cap & IDD specs 8-2-04 Preliminary Rev 1 1.2 Removed "ED" from part number 1.3 Changed data from Final to Preliminary White Electronic Designs Corp. reserves the right to change products or specifications without notice. August 2004 Rev. 1 6 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com