CYPRESS CY62256NLL

CY62256N
256K (32K × 8) Static RAM
256K (32K × 8) Static RAM
Features
Functional Description
The CY62256N[1] is a high performance CMOS static RAM
organized as 32K words by 8 bits. Easy memory expansion is
provided by an active LOW chip enable (CE) and active LOW
output enable (OE) and tristate drivers. This device has an
automatic power down feature, reducing the power consumption
by 99.9 percent when deselected.
An active LOW write enable signal (WE) controls the
writing/reading operation of the memory. When CE and WE
inputs are both LOW, data on the eight data input/output pins
(I/O0 through I/O7) is written into the memory location addressed
by the address present on the address pins (A0 through A14).
Reading the device is accomplished by selecting the device and
enabling the outputs, CE and OE active LOW, while WE remains
inactive or HIGH. Under these conditions, the contents of the
location addressed by the information on address pins are
present on the eight data input/output pins.
The input/output pins remain in a high impedance state unless
the chip is selected, outputs are enabled, and write enable (WE)
is HIGH.
■
Temperature Ranges
❐ Commercial: 0 °C to +70 °C
❐ Industrial: –40 °C to +85 °C
❐ Automotive-A: –40 °C to +85 °C
❐ Automotive-E: –40 °C to +125 °C
■
High Speed: 55 ns
■
Voltage Range: 4.5 V to 5.5 V Operation
■
Low Active Power
❐ 275 mW (max)
■
Low Standby Power (LL version)
❐ 82.5 W (max)
■
Easy Memory Expansion with CE and OE Features
■
TTL-Compatible Inputs and Outputs
■
Automatic Power Down when Deselected
■
CMOS for Optimum Speed and Power
■
Available in Pb-free and non Pb-free 28-pin (600-mil) PDIP,
28-pin (300-mil) Narrow SOIC, 28-pin TSOP-I, and 28-pin
Reverse TSOP-I Packages
Logic Block Diagram
I/O0
INPUTBUFFER
I/O1
32K x 8
ARRAY
I/O2
SENSE AMPS
ROW DECODER
A10
A9
A8
A7
A6
A5
A4
A3
A2
I/O3
I/O4
I/O5
CE
WE
COLUMN
DECODER
I/O6
POWER
DOWN
I/O7
A12
A11
A1
A0
A13
A14
OE
Note
1. For best practice recommendations, do refer to the Cypress application note “System Design Guidelines” on http://www.cypress.com.
Cypress Semiconductor Corporation
Document Number: 001-06511 Rev. *D
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised January 4, 2011
[+] Feedback
CY62256N
Contents
Product Portfolio .............................................................. 3
Pin Configurations ........................................................... 3
Maximum Ratings ............................................................. 4
Operating Range ............................................................... 4
Electrical Characteristics ................................................. 4
Capacitance ...................................................................... 4
Thermal Resistance .......................................................... 5
Data Retention Characteristics ....................................... 5
Switching Characteristics ................................................ 6
Switching Waveforms ...................................................... 6
Document Number: 001-06511 Rev. *D
Typical DC and AC Characteristics ................................ 9
Truth Table ...................................................................... 10
Ordering Information ...................................................... 11
Ordering Code Definitions ......................................... 11
Package Diagrams .......................................................... 12
Document History Page ................................................. 14
Sales, Solutions, and Legal Information ...................... 14
Worldwide Sales and Design Support ....................... 14
Products .................................................................... 14
PSoC Solutions ......................................................... 14
Page 2 of 14
[+] Feedback
CY62256N
Product Portfolio
VCC Range (V)
Product
CY62256NLL
CY62256NLL
CY62256NLL
CY62256NLL
Commercial
Industrial
Automotive-A
Automotive-E
Min
4.5
Typ[2]
5.0
Speed
(ns)
Max
5.5
70
55/70
55/70
55
Power Dissipation
Operating, ICC
Standby, ISB2 (A)
(mA)
[2]
Typ
Max
Typ[2]
Max
25
50
0.1
5
25
50
0.1
10
25
50
0.1
10
25
50
0.1
15
Pin Configurations
Figure 1. 28-pin DIP and Narrow SOIC
Figure 2. 28-pin TSOP I and Reverse TSOP I
Table 1. Pin Definitions
Pin Number
1–10, 21, 23–26
11–13, 15–19,
27
Type
Input
Input/Output
Input/Control
20
22
Input/Control
Input/Control
14
28
Ground
Power Supply
Description
A0–A14. Address Inputs
I/O0–I/O7. Data lines. Used as input or output lines depending on operation
WE. When selected LOW, a WRITE is conducted. When selected HIGH, a READ is
conducted
CE. When LOW, selects the chip. When HIGH, deselects the chip
OE. Output Enable. Controls the direction of the I/O pins. When LOW, the I/O pins
behave as outputs. When deasserted HIGH, I/O pins are tristated, and act as input
data pins
GND. Ground for the device
VCC. Power supply for the device
Note
2. Typical specifications are the mean values measured over a large sample size across normal production process variations and are taken at nominal conditions
(TA = 25 °C, VCC). Parameters are guaranteed by design and characterization, and not 100% tested.
Document Number: 001-06511 Rev. *D
Page 3 of 14
[+] Feedback
CY62256N
Maximum Ratings
Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.
Static discharge voltage.......................................... > 2001 V
(per MIL-STD-883, method 3015)
Storage temperature ................................ –65 C to +150 C
Latch up current..................................................... > 200 mA
Ambient temperature with
power applied ........................................... –55 C to +125 C
Operating Range
Supply voltage to ground potential
(pin 28 to pin 14)...........................................–0.5 V to +7.0 V
DC voltage applied to outputs
in high Z State[3] .................................. –0.5 V to VCC + 0.5 V
DC input voltage[3] ............................... –0.5 V to VCC + 0.5 V
Output current into outputs (LOW) .............................. 20 mA
Range
Ambient Temperature (TA)[4]
VCC
0 C to +70 C
5 V  10%
–40 C to +85 C
5 V  10%
Automotive-A
–40 C to +85 C
5 V  10%
Automotive-E
–40 C to +125 C
5 V  10%
Commercial
Industrial
Electrical Characteristics
Over the Operating Range
Parameter
Description
–55
Test Conditions
–70
Unit
Min
Typ[5]
Max
Min
Typ[5]
Max
2.4
–
–
2.4
–
–
V
VOH
Output HIGH voltage
VCC = Min, IOH = 1.0 mA
VOL
Output LOW voltage
VCC = Min, IOL = 2.1 mA
–
–
0.4
–
–
0.4
V
VIH
Input HIGH voltage
2.2
–
VCC +
0.5 V
2.2
–
VCC +
0.5 V
V
VIL
Input LOW voltage
–0.5
–
0.8
–0.5
–
0.8
V
IIX
Input leakage current
GND < VI < VCC
–0.5
–
+0.5
–0.5
–
+0.5
A
IOZ
Output leakage current
GND < VO < VCC, output disabled
–0.5
–
+0.5
–0.5
–
+0.5
A
ICC
VCC operating supply
current
VCC = Max,
IOUT = 0 mA,
f = fMAX = 1/tRC
ISB1
Automatic CE
power down current—
TTL inputs
LL-Commercial
–
–
–
–
25
50
mA
LL - Industrial
–
25
50
–
25
50
mA
LL - Auto-A
–
25
50
–
25
50
mA
LL - Auto-E
–
25
50
–
–
–
mA
Max. VCC, CE > VIH, LL-Commercial
VIN > VIH or VIN < VIL, LL - Industrial
f = fMAX
LL - Auto-A
LL - Auto-E
ISB2
Automatic CE
power down current—
CMOS inputs
Max. VCC,
LL-Commercial
CE > VCC  0.3 V
LL - Industrial
VIN > VCC  0.3 V, or
LL - Auto-A
VIN < 0.3 V, f = 0
LL - Auto-E
–
–
–
–
0.3
0.5
mA
–
0.3
0.5
–
0.3
0.5
mA
–
0.3
0.5
–
0.3
0.5
mA
–
0.3
0.5
–
–
–
mA
–
–
–
–
0.1
5
A
–
0.1
10
–
0.1
10
A
–
0.1
10
–
0.1
10
A
–
0.1
15
–
–
–
A
Capacitance
Parameter[6]
Description
CIN
Input capacitance
COUT
Output capacitance
Test Conditions
TA = 25 C, f = 1 MHz, VCC = 5.0 V
Max
Unit
6
pF
8
pF
Notes
3. VIL (min) = 2.0 V for pulse durations of less than 20 ns.
4. TA is the “Instant-On” case temperature.
5. Typical specifications are the mean values measured over a large sample size across normal production process variations and are taken at nominal conditions
(TA = 25 °C, VCC). Parameters are guaranteed by design and characterization, and not 100% tested.
6. Tested initially and after any design or process changes that may affect these parameters.
Document Number: 001-06511 Rev. *D
Page 4 of 14
[+] Feedback
CY62256N
Thermal Resistance
Parameter[7]
Description
JA
Thermal resistance
(junction to ambient)
JC
Thermal resistance
(junction to case)
Test Conditions
DIP
SOIC
TSOP
RTSOP
Unit
Still air, soldered on a 4.25 × 1.125
inch, 4-layer printed circuit board
75.61
76.56
93.89
93.89
C/W
43.12
36.07
24.64
24.64
C/W
Figure 3. AC Test Loads and Waveforms
R1 1800 
R1 1800 
5V
5V
OUTPUT
ALL INPUT PULSES
OUTPUT
R2
990
100 pF
INCLUDING
JIG AND
SCOPE
3.0 V
INCLUDING
JIG AND
SCOPE
(a)
R2
990
5 pF
GND
90%
10%
90%
10%
< 5 ns
< 5 ns
(b)
Equivalent to:
THÉVENIN EQUIVALENT
639
OUTPUT
1.77 V
Data Retention Characteristics
Parameter
Conditions[8]
Description
VDR
VCC for data retention
ICCDR
Data retention current
VCC = 2.0V, CE > VCC  0.3V,
LL - Industrial/Auto-A VIN > VCC  0.3V, or VIN < 0.3V
LL - Commercial
LL - Auto-E
tCDR[7]
tR
Chip deselect to data retention time
[7]
Operation recovery time
Min
Typ[9]
Max
Unit
2.0
–
–
V
–
0.1
5
A
–
0.1
10
A
–
0.1
10
A
0
–
–
ns
tRC
–
–
ns
Figure 4. Data Retention Waveform
DATA RETENTION MODE
VCC
3.0 V
tCDR
VDR > 2 V
3.0 V
tR
CE
Notes
7. Tested initially and after any design or process changes that may affect these parameters.
8. No input may exceed VCC + 0.5 V.
9. Typical specifications are the mean values measured over a large sample size across normal production process variations and are taken at nominal conditions
(TA = 25 °C, VCC). Parameters are guaranteed by design and characterization, and not 100% tested.
Document Number: 001-06511 Rev. *D
Page 5 of 14
[+] Feedback
CY62256N
Switching Characteristics
Over the Operating Range[10]
Parameter
CY62256N-55
Description
Min
CY62256N-70
Max
Min
Max
Unit
Read Cycle
tRC
Read cycle time
55
–
70
–
ns
tAA
Address to data valid
–
55
–
70
ns
tOHA
Data hold from address change
5
–
5
–
ns
tACE
CE LOW to data valid
–
55
–
70
ns
tDOE
OE LOW to data valid
–
25
–
35
ns
tLZOE
OE LOW to low Z[11]
5
–
5
–
ns
–
20
–
25
ns
5
–
5
–
ns
[11, 12]
OE HIGH to high Z
tHZOE
CE LOW to low
tLZCE
Z[11]
Z[11, 12]
tHZCE
CE HIGH to high
–
20
–
25
ns
tPU
CE LOW to power up
0
–
0
–
ns
CE HIGH to power down
–
55
–
70
ns
tPD
Write Cycle
[13, 14]
tWC
Write cycle time
55
–
70
–
ns
tSCE
CE LOW to write end
45
–
60
–
ns
tAW
Address setup to write end
45
–
60
–
ns
tHA
Address hold from write end
0
–
0
–
ns
tSA
Address setup to write start
0
–
0
–
ns
tPWE
WE pulse width
40
–
50
–
ns
tSD
Data setup to write end
25
–
30
–
ns
tHD
Data hold from write end
0
–
0
–
ns
Z[11, 12]
–
20
–
25
ns
5
–
5
–
ns
tHZWE
WE LOW to high
tLZWE
WE HIGH to low Z[11]
Switching Waveforms
Figure 5. Read Cycle No. 1[15, 16]
tRC
ADDRESS
tOHA
DATA OUT
PREVIOUS DATA VALID
tAA
DATA VALID
Notes
10. Test conditions assume signal transition time of 5 ns or less, timing reference levels of 1.5 V, input pulse levels of 0 to 3.0 V, and output loading of the specified
IOL/IOH and 100-pF load capacitance.
11. At any temperature and voltage condition, tHZCE is less than tLZCE, tHZOE is less than tLZOE, and tHZWE is less than tLZWE for any device.
12. tHZOE, tHZCE, and tHZWE are specified with CL = 5 pF as in (b) of AC Test Loads. Transition is measured 500 mV from steady-state voltage.
13. The internal Write time of the memory is defined by the overlap of CE LOW and WE LOW. Both signals must be LOW to initiate a Write and either signal can
terminate a Write by going HIGH. The data input setup and hold timing should be referenced to the rising edge of the signal that terminates the Write.
14. The minimum Write cycle time for Write Cycle #3 (WE controlled, OE LOW) is the sum of tHZWE and tSD.
15. Device is continuously selected. OE, CE = VIL.
16. WE is HIGH for Read cycle.
Document Number: 001-06511 Rev. *D
Page 6 of 14
[+] Feedback
CY62256N
Switching Waveforms
(continued)
Figure 6. Read Cycle No. 2[17, 18]
tRC
CE
tACE
OE
tHZOE
tHZCE
tDOE
DATA OUT
tLZOE
HIGH IMPEDANCE
DATA VALID
tLZCE
VCC
SUPPLY
CURRENT
HIGH
IMPEDANCE
tPD
tPU
ICC
50%
50%
ISB
Figure 7. Write Cycle No. 1 (WE Controlled)[19, 20, 21]
tWC
ADDRESS
CE
tAW
tHA
tSA
WE
tPWE
OE
tSD
DATA I/O
NOTE 22
tHD
DATAIN VALID
tHZOE
Figure 8. Write Cycle No. 2 (CE Controlled)[19, 20, 21]
tWC
ADDRESS
tSCE
CE
tSA
tAW
tHA
WE
tSD
DATA I/O
tHD
DATAIN VALID
Notes
17. WE is HIGH for Read cycle.
18. Address valid prior to or coincident with CE transition LOW.
19. The internal Write time of the memory is defined by the overlap of CE LOW and WE LOW. Both signals must be LOW to initiate a Write and either signal can
terminate a Write by going HIGH. The data input setup and hold timing should be referenced to the rising edge of the signal that terminates the Write.
20. Data I/O is high impedance if OE = VIH.
21. If CE goes HIGH simultaneously with WE HIGH, the output remains in a high-impedance state.
22. During this period, the I/Os are in output state and input signals should not be applied.
Document Number: 001-06511 Rev. *D
Page 7 of 14
[+] Feedback
CY62256N
Switching Waveforms
(continued)
Figure 9. Write Cycle No. 3 (WE Controlled, OE LOW)[23, 24]
tWC
ADDRESS
CE
tAW
WE
tHA
tSA
tSD
DATA I/O
NOTE 25
tHD
DATAIN VALID
tHZWE
tLZWE
Notes
23. The minimum Write cycle time for Write Cycle #3 (WE controlled, OE LOW) is the sum of tHZWE and tSD.
24. If CE goes HIGH simultaneously with WE HIGH, the output remains in a high-impedance state.
25. During this period, the I/Os are in output state and input signals should not be applied.
Document Number: 001-06511 Rev. *D
Page 8 of 14
[+] Feedback
CY62256N
Typical DC and AC Characteristics
1.4
1.2
0.8
0.6
VIN = 5.0V
TA = 25C
0.4
0.0
4.0
2.0
1.0
0.8
0.6
VCC = 5.0V
VIN = 5.0V
0.4
4.5
5.0
5.5
0.0
55
6.0
25
SUPPLY VOLTAGE (V)
1.6
1.3
1.4
NORMALIZED tAA
NORMALIZED tAA
1.4
1.2
TA = 25C
1.0
0.8
4.0
NORMALIZED ACCESS TIME
vs. AMBIENT TEMPERATURE
1.2
1.0
4.5
5.0
5.5
6.0
VCC = 5.0V
0.6
55
25
125
OUTPUT SOURCE CURRENT (mA)
120
105
140
OUTPUT SINK CURRENT
vs. OUTPUT VOLTAGE
120
100
80
60
VCC = 5.0V
TA = 25C
40
20
0
0.0
1.0
2.0
3.0
4.0
OUTPUT VOLTAGE (V)
AMBIENT TEMPERATURE (C)
SUPPLY VOLTAGE (V)
25
AMBIENT TEMPERATURE (C)
0.8
0.9
VCC = 5.0V
VIN = 5.0V
–0.5
55
125
AMBIENT TEMPERATURE (C)
NORMALIZED ACCESS TIME
vs. SUPPLY VOLTAGE
1.1
1.0
0.0
0.2
ISB
ISB
1.5
0.5
OUTPUT SINK CURRENT (mA)
0.2
2.5
ISB2 A
1.0
3.0
ICC
1.2
ICC
NORMALIZED ICC
NORMALIZED ICC, ISB
1.4
STANDBY CURRENT
vs. AMBIENT TEMPERATURE
NORMALIZED SUPPLY CURRENT
vs. AMBIENT TEMPERATURE
NORMALIZED SUPPLY CURRENT
vs. SUPPLY VOLTAGE
OUTPUT SOURCE CURRENT
vs. OUTPUT VOLTAGE
100
80
VCC = 5.0V
TA = 25C
60
40
20
0
0.0
1.0
2.0
3.0
4.0
OUTPUT VOLTAGE (V)
Document Number: 001-06511 Rev. *D
Page 9 of 14
[+] Feedback
CY62256N
Typical DC and AC Characteristics
TYPICAL ACCESS TIME CHANGE
vs. OUTPUT LOADING
30.0
2.5
25.0
2.0
1.5
1.0
0.5
0.0
0.0
1.25
20.0
15.0
VCC = 4.5V
TA = 25C
10.0
5.0
1.0
2.0
3.0
4.0
5.0
0.0
0
SUPPLY VOLTAGE (V)
200
400
600
800 1000
CAPACITANCE (pF)
NORMALIZED ICC
3.0
DELTA tAA (ns)
NORMALIZED IPO
TYPICAL POWER-ON CURRENT
vs. SUPPLY VOLTAGE
(continued)
NORMALIZED ICC vs. CYCLE TIME
1.00
VCC = 5.0V
TA = 25C
VIN = 5.0V
0.75
0.50
10
20
30
40
CYCLE FREQUENCY (MHz)
Truth Table
CE
WE
OE
H
X
X
High Z
Inputs/Outputs
Deselect/Power down
Standby (ISB)
L
H
L
Data Out
Read
Active (ICC)
L
L
X
Data In
Write
Active (ICC)
L
H
H
High Z
Output Disabled
Active (ICC)
Document Number: 001-06511 Rev. *D
Mode
Power
Page 10 of 14
[+] Feedback
CY62256N
Ordering Information
Speed
(ns)
55
70
Ordering Code
Package
Diagram
Package Type
CY62256NLL55SNXI
51-85092 28-pin (300-Mil) Narrow SOIC (Pb-free)
CY62256NLL55ZXI
51-85071 28-pin TSOP I (Pb-free)
Operating
Range
Industrial
CY62256NLL55ZXA
51-85071 28-pin TSOP I (Pb-free)
Automotive-A
CY62256NLL55SNXE
51-85092 28-pin (300-Mil) Narrow SOIC (Pb-free)
Automotive-E
CY62256NLL55ZXE
51-85071 28-pin TSOP I (Pb-free)
CY62256NLL70PXC
51-85017 28-pin (600-Mil) Molded DIP (Pb-free)
CY62256NLL70SNXC
51-85092 28-pin (300-Mil) Narrow SOIC (Pb-free)
CY62256NLL70ZRXI
51-85074 28-pin Reverse TSOP I (Pb-free)
CY62256NLL70SNXA
51-85092 28-pin (300-Mil) Narrow SOIC (Pb-free)
Commercial
Industrial
Automotive-A
Do contact your local Cypress sales representative for availability of these parts
Ordering Code Definitions
CY 62 256 N LL - XX XXX X
Temperature Grade: X = C or I or A or E
C = Commercial = 0 °C to +70 °C; I = Industrial = –40 °C to +85 °C;
A = Automotive-A = –40 °C to +85 °C; E = Automotive-E = –40 °C to +125 °C
Package Type: XXX = SNX or ZX or PX or ZRX
SNX = 28-pin Narrow SOIC (Pb-free)
ZX= 28-pin TSOP I (Pb-free)
PX = 28-pin Molded DIP (Pb-free)
ZRX = 28-pin Reverse TSOP I (Pb-free)
Speed Grade: XX = 55 ns or 70 ns
Low Power
Nitride Seal Mask fix
Density: 256 Kbit
MoBL SRAM family
Company ID: CY = Cypress
Document Number: 001-06511 Rev. *D
Page 11 of 14
[+] Feedback
CY62256N
Package Diagrams
Figure 10. 28-pin (600-Mil) Molded DIP, 51-85017
51-85017 *D
Figure 11. 28-pin (300-mil) SNC (Narrow Body), 51-85092
51-85092 *C
Document Number: 001-06511 Rev. *D
Page 12 of 14
[+] Feedback
CY62256N
Figure 12. 28-pin TSOP I (8 × 13.4 mm), 51-85071
51-85071 *H
Figure 13. 28-pin TSOP I (8 × 13.4 mm), 51-85074
51-85074-*F
Document Number: 001-06511 Rev. *D
Page 13 of 14
[+] Feedback
CY62256N
Document History Page
Document Title: CY62256N 256K (32K × 8) Static RAM
Document Number: 001-06511
REV.
ECN NO. Submission
Date
Orig. of
Change
Description of Change
**
426504
See ECN
NXR
New Data Sheet
*A
488954
See ECN
NXR
Added Automotive product
Updated ordering Information table
*B
2715270
06/05/2009
*C
2891344
03/12/2010
VKN/AESA Updated POD of 28-Pin (600-Mil) Molded DIP package (Spec# 51-85017)
VKN
Added Table of Contents
Removed “L” product information
Updated Ordering Information table
Updated Package Diagrams (Figure 10, Figure 11, and Figure 12)
Updated Sales, Solutions, and Legal Information
*D
3119519
01/04/2011
AJU
Updated Ordering Information.
Added Ordering Code Definitions.
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
Products
Automotive
Clocks & Buffers
Interface
Lighting & Power Control
PSoC Solutions
cypress.com/go/automotive
cypress.com/go/clocks
psoc.cypress.com/solutions
cypress.com/go/interface
PSoC 1 | PSoC 3 | PSoC 5
cypress.com/go/powerpsoc
cypress.com/go/plc
Memory
Optical & Image Sensing
cypress.com/go/memory
cypress.com/go/image
PSoC
Touch Sensing
cypress.com/go/psoc
cypress.com/go/touch
USB Controllers
Wireless/RF
cypress.com/go/USB
cypress.com/go/wireless
© Cypress Semiconductor Corporation, 2006-2011. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-06511 Rev. *D
Revised January 4, 2011
Page 14 of 14
All products and company names mentioned in this document may be the trademarks of their respective holders.
[+] Feedback