DS1236 MicroManager Chip www.maxim-ic.com FEATURES PIN ASSIGNMENT Holds microprocessor in check during power transients Halts and restarts an out-of-control microprocessor Monitors pushbutton for external override Warns microprocessor of an impending power failure Converts CMOS SRAM into nonvolatile memory Unconditionally write-protects memory when power supply is out of tolerance Consumes less than 100 nA of battery current at 25°C Controls external power switch for high current applications Accurate 10% power supply monitoring Optional 5% power supply monitoring designated DS1236-5 Provides orderly shutdown in nonvolatile microprocessor applications Supplies necessary control for low-power “stop mode” in battery operated hand-held applications Standard 16-pin DIP or space-saving 16-pin SOIC Optional industrial temperature range -40°C to +85°C VBAT 1 16 RST VCCO 2 15 RST VCC 3 14 PBRST GND 4 13 CEI PF 5 12 CEO PF 6 11 ST WC/SC 7 10 NMI RC 8 9 IN VBAT VCCO VCC GND PF PF WC/SC RCI 16-Pin DIP (300-mil) See Mech. Drawings Section 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 RST RST PBRST CEI CEO ST NMI IN 16-Pin SOIC (300-mil) See Mech. Drawings Section PIN DESCRIPTION VBAT VCCO VCC GND PF PF WC/ SC RC IN NMI ST CEO CEI PBRST RST RST - +3-Volt Battery Input - Switched SRAM Supply Output - +5-Volt Power Supply Input - Ground - Power-Fail (Active High) - Power-Fail (Active Low) - Wake-Up Control (Sleep) - Reset Control - Early Warning Input - Non-Maskable Interrupt - Strobe Input - Chip Enable Output - Chip Enable Input - Pushbutton Reset Input - Reset Output (Active Low) - Reset Output (Active High) DESCRIPTION The DS1236 MicroManager Chip provides all the necessary functions for power supply monitoring, reset control, and memory backup in microprocessor-based systems. A precise internal voltage reference and comparator circuit monitor power supply status. When an out-of-tolerance condition occurs, the microprocessor reset and power-fail outputs are forced active, and static RAM control unconditionally write protects external memory. The DS1236 also provides early warning detection of a user-defined threshold by driving a non-maskable interrupt. External reset control is provided by a pushbutton reset 1 of 19 011107 DS1236 input which is debounced and activates reset outputs. An internal watchdog timer can also force the reset outputs to the active state if the strobe input is not driven low prior to watchdog timeout. Reset control and wake-up/sleep control inputs also provide the necessary signals for orderly shutdown and startup in battery backup and battery operated applications. A block diagram of the DS1236 is shown in Figure 1. PIN DESCRIPTION PIN NAME DESCRIPTION VBAT +3V battery input provides nonvolatile operation of control functions. VCCO VCC output for nonvolatile SRAM applications. VCC +5V primary power input. PF Power-fail indicator, active high, used for external power switching as shown in Figure 9. PF Power-fail indicator, active low. WC/ SC Wake-up and Sleep control. Invokes low-power mode. RC Reset control input. Determines reset output. Normally low for NMOS processors and high for battery backed CMOS processors. IN Early warning power-fail input. This voltage sense point can be tied (via resistor divider) to a user-selected voltage. NMI ST Non-maskable interrupt. Used in conjunction with the IN pin to indicate an impending power failure. Strobe input. A high-to-low transition will reset the watchdog timer, indicating that software is still in control. CEO Chip enable output. Used with nonvolatile SRAM applications. CEI Chip enable input. PBRST Pushbutton reset input. RST Active low reset output. RST Active high reset output. PROCESSOR MODE A distinction is often made between CMOS and NMOS processor systems. In a CMOS system, power consumption may be a concern, and nonvolatile operation is possible by battery backing both the SRAM and the CMOS processor. All resources would be maintained in the absence of VCC. A power-down reset is not issued since the low-power mode of most CMOS processors (Stop) is terminated with a Reset. A pulsed interrupt ( NMI ) is issued to allow the CMOS processor to invoke a sleep mode to save power. For this case, a power-on reset is desirable to wake up and initialize the processor. The CMOS mode is invoked by connecting RC to VCCO. An NMOS processor consumes more power, and consequently may not be battery backed. In this case, it is desirable to notify the processor of a power-fail, then keep it in reset during the loss of VCC. This avoids intermittent or aberrant operation. On power-up, the processor will continue to be reset until VCC reaches an operational level to provide an orderly start. The NMOS mode is invoked by connecting RC to ground. 2 of 19 DS1236 POWER MONITOR The DS1236 employs a band gap voltage reference and a precision comparator to monitor the 5-volt supply (VCC) in microprocessor-based systems. When an out-of-tolerance condition occurs, the RST and RST outputs are driven to the active state. The VCC trip point (VCCTP) is set for 10% operation so that the RST and RST outputs will become active as VCC falls below 4.5 volts (4.37 typical). The VCCTP for the 5% operation option (DS1236-5) is set for 4.75 volts (4.62 typical). The RST and RST signals are excellent for microprocessor reset control, as processing is stopped at the last possible moment of intolerance VCC. On power-up, the RST and RST signals are held active for a minimum of 25 ms (100 ms typical) after VCCTP is reached to allow the power supply and microprocessor to stabilize. Note: The operation described above is obtained with the reset control pin (RC) connected to GND (NMOS mode). Please review the reset control section for more information. WATCHDOG TIMER The DS1236 provides a watchdog timer function which forces the RST and RST signals to the active state when the strobe input ( ST ) is not stimulated for a predetermined time period. This time period is 400 ms typically with a maximum time-out of 600 ms. The watchdog time-out period begins as soon as RST and RST are inactive. If a high-to-low transition occurs at the ST input prior to time-out, the watchdog timer is reset and begins to time out again. The ST input timing is shown in Figure 2. To guarantee the watchdog timer does not time out, a high-to-low transition on ST must occur at or less than 100 ms (minimum time-out) from a reset. If the watchdog timer is allowed to time out, the RST and RST outputs are driven to the active state for 25 ms minimum. The ST input can be derived from microprocessor address, data, and/or control signals. Under normal operating conditions, these signals would routinely reset the watchdog timer prior to time-out. If the watchdog timer is not required, two methods have been provided to disable it. Permanently grounding the IN pin in the CMOS mode (RC=1) will disable the watchdog. In normal operation with RC=1, the watchdog is disabled as soon as the IN pin is below VTP. With IN grounded, an NMI output will occur only at power-up, or when the ST pin is strobed. As shown in the Figure 3, a falling edge on ST will generate an NMI when IN is below VTP. This allows the processor to verify that power is between VTP and VCCTP, as an NMI will be returned immediately after the ST strobe. The watchdog timer is not affected by the IN pin when in NMOS mode (RC=0). If the NMI signal is required to monitor supply voltages, the watchdog may also be disabled by leaving the ST input open. Independent of the state of the RC pin, the watchdog is also disabled as soon as VCC falls to VCCTP. PUSHBUTTON RESET An input pin is provided on the DS1236 for direct connection to a pushbutton. The pushbutton reset input requires an active low signal. Internally, this input is pulled high by a 10k resistor whenever VCC is greater than VBAT. The PBRST pin is also debounced and timed such that the RST and RST outputs are driven to the active state for 25 ms minimum. This 25 ms delay begins as the pushbutton is released from a low level. A typical example of the power monitor, watchdog timer, and pushbutton reset connections are shown in Figure 4. The PBRST input is disabled whenever the IN pin voltage level is less than VTP and the reset control (RC) is tied high (CMOS mode). The PBRST input is also disabled whenever VCC is below VBAT. Timing of the PBRST -generated RST is illustrated in Figure 5. 3 of 19 DS1236 NON-MASKABLE INTERRUPT The DS1236 generates a non-maskable interrupt NMI for early warning of power failure to a microprocessor. A precision comparator monitors the voltage level at the IN pin relative to a reference generated by the internal band gap. The IN pin is a high-impedance input allowing for a user-defined sense point. An external resistor voltage divider network (Figure 6) is used to interface with high voltage signals. This sense point may be derived from the regulated 5-volt supply or from a higher DC voltage level closer to the main system power input. Since the IN trip point VTP is 2.54 volts, the proper values for R1 and R2 can be determined by the equation as shown in Figure 6. Proper operation of the DS1236 requires that the voltage at the IN pin be limited to VIN. Therefore, the maximum allowable voltage at the supply being monitored (VMAX) can also be derived as shown in Figure 6. A simple approach to solving this equation is to select a value for R2 high enough to keep power consumption low, and solve for R1. The flexibility of the IN input pin allows for detection of power loss at the earliest point in a power supply system, maximizing the amount of time for microprocessor shutdown between NMI and RST or RST . When the supply being monitored decays to the voltage sense point, the DS1236 pulses the NMI output to the active state for a minimum of 200 μs. The NMI power-fail detection circuitry also has built-in time domain hysteresis. That is, the monitored supply is sampled periodically at a rate determined by an internal ring oscillator running at approximately 30 kHz (33 μs/cycle). Three consecutive samplings of out-of-tolerance supply (below VSENSE) must occur at the IN pin to activate NMI . Therefore, the supply must be below the voltage sense point for approximately 100 μs or the comparator will reset. In this way, power supply noise is removed from the monitoring function, preventing false trips. During a power-up, any IN pin levels below VTP are disabled from reaching the NMI pin until VCC rises to VCCTP. As a result, any potential NMI pulse will not be initiated until VCC reaches VCCTP. Removal of an active low level on the NMI pin is controlled by either an internal time-out (when IN pin is less than VTP) or by the subsequent rise of the IN pin above VTP. The initiation and removal of the NMI signal during power-up results in an NMI pulse of from 0 μs minimum to 500 μs maximum, depending on the relative voltage relationship between VCC and the IN pin voltage. As an example, when the IN pin is tied to ground during power-up, the internal time-out will result in a pulse of 200 μs minimum to 500 μs maximum. In contrast, if the IN pin is tied to VCCO during power-up, NMI will not produce a pulse on power-up. Note that a fast slewing power supply may cause the NMI to be virtually nonexistent on power-up. This is of no consequence, however, since an RST will be active. 4 of 19 DS1236 DS1236 FUNCTIONAL BLOCK DIAGRAM Figure 1 If the IN pin is connected to VCCO, the NMI output will pulse low as VCC decays to VCCTP in the NMOS mode (RC=0). In the CMOS mode (RC=VCCO) the power-down of VCC out-of-tolerance at VCCTP will not produce a pulse on the NMI pin. Given that any NMI pulse has been completed by the time VCC decays to VCCTP, the NMI pin will remain high. The NMI voltage will follow VCC down until VCC decays to VBAT. Once VCC decays to VBAT, the NMI pin will either remain at VOHL or enter tri-state mode as determined by the RC pin (see “Reset Control” section). MEMORY BACKUP The DS1236 provides all of the necessary functions required to battery back a static RAM. First, a switch is provided to direct SRAM power from the incoming 5-volt supply (VCC) or from an external battery (VBAT), whichever is greater. This switched supply (VCCO) can also be used to battery back a CMOS microprocessor. For more information about nonvolatile processor applications, review the “Reset Control” and “Wake Control” sections. Second, the same power-fail detection described in the power monitor section is used to hold the chip enable output ( CEO ) to within 0.3 volts of VCC or to within 0.7 volts of VBAT. This write protection mechanism occurs as VCC falls below VCCTP as specified. If CEI is 5 of 19 DS1236 low at the time power-fail detection occurs, CEO is held in its present state until CEI is returned high, or the period tCE expires. This delay of write protection until the current memory cycle is completed prevents the corruption of data. If CEO is in an inactive state at the time of VCC fail detection, CEO will be unconditionally disabled within tCF. During nominal supply conditions CEO will follow CEI with a maximum propagation delay of 20 ns. Figure 7 shows a typical nonvolatile SRAM application. FRESHNESS SEAL In order to conserve battery capacity during storage and/or shipment of an end system, the DS1236 provides a freshness seal to electrically disconnect the battery. Figure 8 depicts the three pulses below ground on the IN pin required to invoke the freshness seal. The freshness seal will be disconnected and normal operation will begin when VCC is cycled and reapplied to a level above VBAT. To prevent negative pulses associated with noise from setting the freshness mode in system applications, a series diode and resistor can be used to shunt noise to ground. During manufacturing, the freshness seal can still be set by holding TP2 at -3 volts while applying the 0 to –3 volts clock to TP1. POWER SWITCHING When larger operating currents are required in a battery backed system, the 5-volt supply and battery supply switches internal to the DS1236 may not be large enough to support the required load through VCCO with a reasonable voltage drop. For these applications, the PF and PF outputs are provided to gate external power switching devices. As shown in Figure 9, power to the load is switched from VCC to battery on power-down, and from battery to VCC on power-up. The DS1336 is designed to use the PF output to switch between VBAT and VCC. It provides better leakage and switchover performance than currently available discrete components. The transition threshold for PF and PF is set to the external battery voltage VBAT, allowing a smooth transition between sources. The load applied to the PF pin from the external switch will be supplied by the battery. Therefore, if a discrete switch is used, this load should be taken into consideration when sizing the battery. RESET CONTROL As mentioned above, the DS1236 supports two modes of operation. The CMOS mode is used when the system incorporates a CMOS microprocessor which is battery backed. The NMOS mode is used when a non-battery backed processor is incorporated. The mode is selected by the RC (Reset Control) pin. The level of this pin distinguishes timing and level control on RST, RST , and NMI outputs for volatile processor operation versus nonvolatile battery backup or battery operated processor applications. ST/INPUT TIMING Figure 2 6 of 19 DS1236 NMI/FROM ST/INPUT Figure 3 POWER MONITOR, WATCHDOG Figure 4 PUSH BUTTON RESET TIMING Figure 5 NON-MASKABLE INTERRUPT Figure 6 7 of 19 DS1236 EXAMPLE 1: 5 VOLT SUPPLY, R2 = 10k OHM, VSENSE = 4.80 VOLTS ∴ 4.80 = R1 + 10k X 2.54 10k R1 = 8.9k OHM EXAMPLE 2: 12 VOLT SUPPLY, R2 = 10k OHM, VSENSE = 9.00 VOLTS ∴ 9.00 = R1 + 10k X 2.54 10k VMAX = R1 = 25.4k OHM 9.00 X 5.00 = 17.7 VOLTS 2.54 NONVOLATILE SRAM Figure 7 8 of 19 DS1236 When the RC pin is tied to ground, the DS1236 is designed to interface with NMOS processors which do not have the microamp currents required during a battery backed mode. Grounding the RC pin does, however, continue to support nonvolatile backup of system SRAM memory. Nonvolatile systems incorporating NMOS processors generally require that only the SRAM memory and/or timekeeping functions be battery backed. When the processor is not battery backed (RC = 0), all signals connected from the processor to the DS1236 are disconnected from the backup battery supply, or grounded when system VCC decays below VBAT. In the NMOS processor system, the principal emphasis is placed on giving early warnings with NMI , then providing a continuously active RST and RST signal during power-down while isolating the backup battery from the processor during a loss of VCC. During power-down, NMI will pulse low for a minimum of 200 μs, and then return high. If RC is tied low (NMOS mode), the voltage on NMI will follow VCC until VCC supply decays to VBAT, at which point NMI will enter tri-state (see timing diagram). Also, upon VCC out-of-tolerance at VCCTP, the RST and RST outputs are driven active and RST will follow VCC as the supply decays. On power-up, RST follows VCC up, RST is held low, and both remain active for tRST after valid VCC. During a power-up from a VCC voltage below VBAT, any detected IN pin levels below VTP are disabled from reaching the NMI pin until VCC rises to VCCTP. As a result, any potential NMI pulse will not be initiated until VCC reaches VCCTP. Removal of an active low level on the NMI pin is controlled by either an internal time-out (when the IN pin is less than VTP), or by the subsequent rise of the IN pin above VTP. The initiation and removal of the NMI signal results in an NMI pulse of 0 μs minimum to 500 μs maximum during power-up, depending on the relative voltage relationship between VCC and the IN pin. As an example, when the IN pin is tied to ground, the internal timeout will result in a pulse of 200 μs minimum to 500 μs maximum. In contrast, if the IN pin is tied to VCCO, NMI will not produce a pulse on power-up. Connecting the RC pin to a high (VCCO) invokes CMOS mode and provides nonvolatile support to both the system SRAM as well as a low power CMOS processor. When using CMOS microprocessors, it is possible to place the microprocessor into a very low-power mode termed the “stop” or “halt” mode. In this state the CMOS processor requires only microamp currents and is fully capable of being battery backed. This mode generally allows the CMOS microprocessor to maintain the contents of internal RAM as well as state control of I/O ports during battery backup. The processor can subsequently be restarted by any of several different signals. To maintain this low-power state, the DS1236 issues no NMI and/or reset signals to the processor until it is time to bring the processor back into full operation. To support the lowpower processor battery backed mode (RC = 1), the DS1236 provides a pulsed NMI for early power failure warning. Waiting to initiate a Stop mode until after the NMI pin has returned high will guarantee the processor that no other active NMI or RST/ RST will be issued by the DS1236 until one of two conditions occurs: 1) Voltage on the pin rises above VTP, which activates the watchdog, or 2) VCC cycles below then above VBAT, which also results in an active RST and RST . If VCC does not fall below VCCTP, the processor will be restarted by the reset derived from the watchdog timer as the IN pin rises above VTP. With the RC pin tied to VCCO, RST and RST are not forced active as VCC collapses to VCCTP. The RST is held at a high level via the external battery as VCC falls below battery potential. This mode of operation is intended for applications in which the processor is made nonvolatile with an external source, and allows the processor to power down into a Stop mode as signaled from NMI at an earlier voltage level. The NMI output pin will pulse low for tNMI following a low voltage detect at the IN pin of VTP. Following tNMI , however, NMI will also be held at a high level (VBAT) by the battery as VCC decays below VBAT. On power-up, RST and RST are held inactive until VCC reaches VBAT, then RST and RST are driven active for tRST. If the IN pin falls below VTP during an active reset, the reset outputs will be forced inactive by the NMI output. In addition, as long as the IN pin is less than VTP, stimulation of the ST pin will result in 9 of 19 DS1236 additional NMI pulses. In this way, the ST pin can be used to allow the CMOS processor to determine if the supply voltage, as monitored by the IN pin, is above or below a selected operating value. This is illustrated in Figure 3. As discussed above, the RC pin determines the timing relationships and levels of several signals. The following section describes the power-up and power-down timing diagrams in more detail. TIMING DIAGRAMS This section provides a description of the timing diagrams shown in Figure 10, Figure 11, Figure 12, and Figure 13. These diagrams show the relative timing and levels in both the NMOS and the CMOS mode for power-up and down. Figure 10 illustrates the relationship for power-down in CMOS mode. As VCC falls, the IN pin voltage drops below VTP. As a result, the processor is notified of an impending power failure via an active NMI , which allows it to enter a sleep mode. As the power falls further, VCC crosses VCCTP, the power monitor trip point. Since the DS1236 is in CMOS mode, no reset is generated. The RST voltage will follow VCC down, but will fall no further than VBAT. At this time, CEO is brought high to write protect the RAM. When the VCC reaches VBAT, a power-fail is issued via the PF and PF pins. Figure 11 illustrates operation of the power-down sequence in NMOS mode. Once again, as power falls, an NMI is issued. This gives the processor time to save critical data in nonvolatile SRAM. When VCC reaches VCCTP, an active RST and RST are given. The RST voltage will follow VCC as it falls. CEO , PF, and PF will operate in a similar manner to CMOS mode. Notice that the NMI will tri-state to prevent a loss of battery power. Figure 12 shows the power-up sequence for the NMOS mode. As VCC slews above VBAT, the PF and PF pins are deactivated. An active reset occurs as well as an NMI . Although the NMI may be short due to slew rates, reset will be maintained for the standard tRST timeout period. At a later time, if the IN pin falls below VTP, a new NMI will occur. If the processor does not issue a ST , a watchdog reset will also occur. The second NMI and RST are provided to illustrate these possibilities. Figure 13 illustrates the power-up timing for CMOS mode. The principal difference is that the DS1236 issues a reset immediately in the NMOS mode. In CMOS mode, a reset is issued when IN rises above VTP. Depending on the processor type, the NMI may terminate the Stop mode in the processor. WAKE CONTROL/SLEEP CONTROL The Wake/Sleep Control input (WC/ SC ) allows the processor to disable all comparators on the DS1236 before entering the Stop mode. This feature allows the DS1236, processor, and static RAM to maintain nonvolatility in the lowest power mode possible. The processor may invoke the sleep mode in battery operated applications to conserve battery capacity when an absence of activity is detected. The operation of this signal is shown in Figure 14. The DS1236 may subsequently be restarted by a high-to-low transition on the PBRST input through human interface via a keyboard, touchpad, etc. The processor will then be restarted as the watchdog times out and drives RST and RST active. The DS1236 can also be started up by forcing the WC/ SC pin high from an external source. Also, if the DS1236 is placed in a sleep mode by the processor and system power is lost, the DS1236 will wake up the next time VCC rises above VBAT. These possibilities are illustrated in Figure 15. When the sleep mode is invoked during normal power-valid conditions, all operation on the DS1236 is disabled, thus leaving the NMI , RST, and RST outputs disabled as well as the ST and IN inputs. However, a loss of power during a sleep mode will result in an active RST and RST when the RC pin is grounded (NMOS mode). If the RC pin is tied high, the RST and RST pins will remain inactive during 10 of 19 DS1236 power-down in a sleep mode. Removal of the sleep mode by the PBRST input is not affected by the IN pin threshold at VTP when the RC pin is tied high (CMOS mode). Subsequent power-up of the VCC supply with the RC pin tied high will activate the RST and RST outputs as the main supply rises above VBAT. A high-to-low transition on the WC/ SC pin must follow a high-to-low transition on the ST pin by tWC to invoke a Sleep mode for the DS1236. FRESHNESS SEAL Figure 8 NOTE: This series of pulses must be applied during normal +5 volt operation. POWER SWITCHING Figure 9 11 of 19 DS1236 CMOS MODE POWER-DOWN (RC = VCCO) Figure 10 12 of 19 DS1236 NMOS MODE POWER-DOWN (RC = GND) Figure 11 13 of 19 DS1236 NMOS MODE POWER-UP (RC = GND) Figure 12 14 of 19 DS1236 CMOS MODE POWER-UP (RC = VCCO) Figure 13 15 of 19 DS1236 WAKE/SLEEP CONTROL Figure 14 OPTIONS FOR INVOKING WAKEUP Figure 15 16 of 19 DS1236 ABSOLUTE MAXIMUM RATINGS* Voltage on VCC Pin Relative to Ground Voltage on I/O Relative to Ground Voltage on IN Pin Relative to Ground Operating Temperature Operating Temperature (Industrial Version) Storage Temperature Soldering Temperature -0.5V to +7.0V -0.5V to VCC + 0.5V -3.5V to VCC + 0.5V 0°C to 70°C -40°C to +85°C -55°C to +125°C 260°C for 10 seconds * This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. RECOMMENDED DC OPERATING CONDITIONS (0°C to 70°C) PARAMETER SYMBOL MIN TYP MAX UNITS NOTES Supply Voltage VCC 4.5 5.0 5.5 V 1 Supply Voltage (5% Option) VCC 4.75 5.0 5.5 V 1 Input High Level VIH 2.0 VCC+0.3 V 1 Input Low Level VIL -0.3 +0.8 V 1 IN Input Pin VIN -0.3 VCC+0.3 V 1 Battery Input VBAT 2.7 4.0 V 1 (0°C to 70°C; VCC= 4.5V to 5.5V) DC ELECTRICAL CHARACTERISTICS PARAMETER SYMBOL Supply Current MAX UNITS NOTES ICC 4 mA 2 Sleep Supply Current in Sleep mode ICC 20 μA Battery Current IBAT 0.1 μA 2 Supply Output Current (VCCO=VCC - 0.3V) ICC01 100 mA 3 Supply Output Current in Data Retention (VCC < VBAT) ICC02 1 mA 4 Supply Output Voltage VCCO VCC-0.3 V 1 Battery Backup Voltage VCCO VBAT-0.7 V 1, 6 Low Level @ RST VOL V 1 Output Voltage @ -500 μA VOH VCC-0.5V VCC-0.1V V 1 VOHL VBAT-0.7 V 1, 6 CEO and PF Output MIN TYP 0.4 RPBRST 10k Input Leakage Current ILI -1.0 +1.0 μA 18 Output Leakage Current ILO -1.0 +1.0 μA 18 Output Current @ 0.4V IOL 4.0 mA 12 PBRST Pull-up Resist 17 of 19 Ohms DS1236 PARAMETER SYMBOL MIN TYP MAX UNITS NOTES -1.0 mA 13 Output Current @ 2.4V IOH Power Sup. Trip Point VCCTP 4.25 4.37 4.50 V 1 Power Supply Trip (5% Option) VCCTP 4.50 4.62 4.75 V 1 IN Input Pin Current ICCIN -1.0 +1.0 μA IN Input Trip Point VTP 2.5 2.6 V 1 (0°C to 70°C; VCC= 4.5V to 5.5V) AC ELECTRICAL CHARACTERISTICS PARAMETER 2.54 SYMBOL MIN TYP MAX UNITS VCC Fail Detect to RST, RST tRPD 40 100 175 μs VTP to NMI tIPD 40 100 175 μs RESET Active Time tRST 25 100 150 ms tNMI 200 300 500 μs 14 tST 20 ns 19 tPB 40 ms VCC Slew Rate 4.75 to 4.25 tF 300 μs Chip Enable Propagation Delay tPD VCC Fail to Chip Enable High tCF VCC Valid to RST, RST (RC=1) tFPU VCC Valid to RST & RST tRPU 25 VCC Slew to 4.24 to VBAT tFB1 VCC Slew 4.25 to 4.75 VBAT Chip Enable Output Recovery Time NMI ST Pulse Width Pulse Width PBRST @ VIL NOTES 20 ns 44 μs 100 ns 150 ms 5 10 μs 7 tFB2 100 μs 8 tREC .1 μs 9 VCC Slew 4.25 to 4.75 tR 0 μs Chip Enable Pulse Width tCE Watchdog Time Delay tTD 100 tWC 0.1 7 12 100 17 5 s 600 ms 50 μs tPPF 2 μs 7 tSTN 30 ns 11 tNRT 30 ns VBAT Detect to RST & RST tARST 200 μs 15 VCC Valid to RST, RST tBRST 150 μs 16 ST to WC/ SC VBAT Detect to PF, PF ST to NMI NMI to RST & RST 30 18 of 19 400 100 10 DS1236 CAPACITANCE PARAMETER Input Capacitance Output Capacitance (tA=25°C) SYMBOL MIN TYP MAX UNITS CIN 5 pF COUT 7 pF NOTES NOTES: 1. All voltages referenced to ground. A 0.1 μF capacitor is recommended between VCC and GND. 2. Measured with VCCO, CEO , PF, ST , PBRST , RST, RST , and NMI pin open. IBAT specified at 25°C. 3. ICCO1 is the maximum average load which the DS1236 can supply at VCC-0.3V through the VCCO pin during normal 5-volt operation. 4. ICCO2 is the maximum average load which the DS1236 can supply through the VCCO pin during data retention battery supply operation, with a maximum drop of 0.8 volts. 5. With tR = 5 μs. 6. VCCO is approximately VBAT-0.5V at 1 μA load. 7. Sleep mode is not invoked. 8. Sleep mode is invoked. 9. tREC is the minimum time required before CEI / CEO memory access is allowed. 10. tCE maximum must be met to ensure data integrity on power loss. 11. IN input is less than VTP but VCC greater than VCCTP. 12. All outputs except RST which is 25 μA minimum. 13. All outputs except RST and NMI which is 25 μA maximum. 14. Pulse width of NMI requires that the IN pin remain below VTP. If the IN pin returns to a level above VTP for a period longer than tIPD and before the tNMI period has elapsed, the NMI pin will immediately return to a high. 15. IN pin greater than VTP when VCC supply rises to VBAT. Example: IN tied to GND. 16. IN pin less than VTP when VCC supply rises to VBAT. 17. CEI low. 18. The WC/ SC pin contains an internal latch which drives back on to the pin. This latch requires ±200 μamps to switch states. The ST pin will sink ±50 μamps in normal operation and ±1 μamp in the sleep mode. 19. ST should be active low before the watchdog is disabled (i.e., before the ST input is tristated). 19 of 19