SMD 8 Pin 5 Tap TTL Compatible Active Delay Lines ELECTRONICS INC. EPA1140-XX & EPA1140-XX-RC Add “-RC” after part number for RoHS Compliant PCA Part Number EPA1140-25(-RC) EPA1140-30(-RC) EPA1140-35(-RC) EPA1140-40(-RC) EPA1140-45(-RC) EPA1140-50(-RC) EPA1140-60(-RC) EPA1140-75(-RC) EPA1140-100(-RC) EPA1140-125(-RC) Total Delay (†±5% or ± 2nS) Tap Delays (†±5% or ± 2nS) 5, 10, 15, 20 6, 12, 18, 24 7, 14, 21, 28 8, 16, 24, 32 9, 18, 27, 36 10, 20, 30, 40 12, 24, 36, 48 15, 30, 45, 60 20, 40, 60, 80 25, 50, 75, 100 PCA Part Number EPA1140-150(-RC) EPA1140-175(-RC) EPA1140-200(-RC) EPA1140-225(-RC) EPA1140-250(-RC) EPA1140-300(-RC) EPA1140-350(-RC) EPA1140-400(-RC) EPA1140-450(-RC) EPA1140-500(-RC) 25 30 35 40 45 50 60 75 100 125 Tap Delays (†±5% or ± 2nS) Total Delay (†±5% or ± 2nS) 30, 60, 90, 120 35, 70, 105, 140 40, 80, 120, 160 45, 90, 135, 180 50, 100, 150, 200 60, 120, 180, 240 70, 140, 210, 280 80, 160, 240, 320 90, 180, 270, 360 100, 200, 300, 400 150 175 200 225 250 300 350 400 450 500 †Whichever is greater. Delay times referenced from input to leading and trailing edges at 25°C, 5.0V, with no load. DC Electrical Characteristics Parameter VOH VOL VIK IIH Test Conditions Min. V CC = min. V IL = max. I OH = max 2.7 V CC = min. V IH = min. I OL = max V CC = min. II = II K V CC = max. VIN = 2.7V V CC = max. VIN = 5.25V IIL Low-Level Input Current V CC = max. VIN = 0.5V IOS Short Circuit Output Current V CC = max. V OUT = 0. -40 (One output at a time) ICCH High-Level Supply Current V CC = max. VIN = OPEN ICCL Low-Level Supply Current V CC = max. VIN = 0 TRO Output Rise Time Td ≤ 500 nS (0.75 to 2.4 Volts) NH Fanout High-Level Output V CC = max. V OH = 2.7V NL Fanout Low-Level Output V CC = max. V OL = 0.5V Max. Unit 0.5 -1.2 50 1.0 -2 -100 V V V µA mA mA mA High-Level Output Voltage Low-Level Output Voltage Input Clamp Voltage High-Level Input Current Schematic 8 VCC 7 2 6 Recommended Operating Conditions Min. Supply Voltage High-Level Input Voltage Low-Level Input Voltage Input Clamp Current High-Level Output Current Low-Level Output Current Pulse Width of Total Delay Duty Cycle Operating Free-Air Temperature 4.75 2.0 Max. Unit 5.25 V V V mA mA mA % % °C 0.8 -18 -1.0 20 40 -55 40 +125 5 OUTPUT INPUT 1 4 GROUND 75 mA 75 mA 4 nS 20 TTL Load 10 TTL Load Package .030 (.762) PCA .400 .280 Max. EPA1140-25(-RC) Max. (10.16) (7.11) D.C. VCC VIH VIL IIK IOH IOL PW* d* TA 3 .055 (1.40) .100 (2.54) Pad Layout .410 (10.41) .100 (2.54) .500 Max. .010 Typ. (.254) .250 Max. (6.35) .020 (.508) .050 (1.27) .300 (7.62) *These two values are inter-dependent. Notes : Input Pulse Test Conditions @ 25° C EIN PW TRI PRR Pulse Input Voltage Pulse Width % of Total Delay Pulse Rise Time (0.75 - 2.4 Volts) Pulse Repetition Rate @ Td ≤ 200 nS Pulse Repetition Rate @ Td > 200 nS VCC Supply Voltage Unit 3.2 110 2.0 1.0 100 5.0 Volts % nS MHz KHz Volts EPA1140-XX EPA1140-XX-RC 1. Lead Finish SnPb Hot Tin Dip (Sn) † 2. Peak Temperature Rating 225°C 260°C 4. Weight .976 grams .976 grams (Tube) TBD pieces/tube 5. Packaging Information (*Add “TR” to end of part (Tape & Reel) TBD pieces/13” reel number, but in front of (*EPA1140-XXTR) “-RC”when placing order) TBD pieces/tube TBD pieces/13” reel (*EPA1140-XXTR-RC) † Lead Material : Matte Tin with Ni Barrier Unless Otherwise Specified Dimensions are in Inches /mm ± .010 /.25 PCA ELECTRONICS, INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 Product performance is limited to specified parameters. Data is subject to change without prior notice. CSA1140-XX & -RC Rev. B 8/17/06 RR TEL: (818) 892-0761 FAX: (818) 894-5791 http://www.pca.com