SO SMD 14 Pin 5 Tap TTL Compatible Active Delay Lines TAP DELAYS ±5% or ±2 nS† TOTAL DELAYS ±5% or ±2 nS† 5, 10, 15, 20 6, 12, 18, 24 7, 14, 21, 28 8, 16, 24, 32 9, 18, 27, 36 10, 20, 30, 40 12, 24, 36, 48 15, 30, 45, 60 †Whichever is greater. 25 30 35 40 45 50 60 75 PART NUMBER TAP DELAYS ±5% or ±2 nS† TOTAL DELAYS ±5% or ±2 nS† PART NUMBER EPA424-25 EPA424-30 EPA424-35 EPA424-40 EPA424-45 EPA424-50 EPA424-60 EPA424-75 20, 40, 60, 80 25, 50, 75, 100 30, 60, 90, 120 35, 70, 105, 140 40, 80, 120, 160 45, 90, 135, 180 50, 100, 150, 200 100 125 150 175 200 225 250 EPA424-100 EPA424-125 EPA424-150 EPA424-175 EPA424-200 EPA424-225 EPA424-250 Delay times referenced from input to leading edges at 25°C, 5.0V, with no load. DC Electrical Characteristics Parameter Test Conditions VOH VOL VIK IIH Schematic Min Max Unit High-Level Output Voltage Low-Level Output Voltage Input Clamp Voltage High-Level Input Current VCC = min. VIL = max. I OH = max 2.7 VCC = min. VIH = min. I OL= max VCC = min. II = II K VCC = max. VIN = 2.7V VCC = max. VIN = 5.25V IIL Low-Level Input Current VCC = max. VIN = 0.5V IOS Short Circuit Output Current VCC = max. VOUT = 0. -40 (One output at a time) ICCH High-Level Supply Current VCC = max. VIN = OPEN ICCL Low-Level Supply Current VCC = max. VIN = 0 TRO Output Rise Time Td ≤ 500 nS (0.75 to 2.4 Volts) NH Fanout High-Level Output VCC = max. VOH = 2.7V NL Fanout Low-Level Output VCC = max. VOL = 0.5V Recommended Operating Conditions VCC VIH VIL IIK IOH IOL PW* d* TA Supply Voltage High-Level Input Voltage Low-Level Input Voltage Input Clamp Current High-Level Output Current Low-Level Output Current Pulse Width of Total Delay Duty Cycle Operating Free-Air Temperature 0.5 -1.2 50 1.0 -2 -100 V V V µA mA mA mA 14 VCC 12 4 10 6 8 OUTPUT INPUT 1 7 GROUND 75 mA 75 mA 4 nS 20 TTL LOAD 10 TTL LOAD Package Dimensions Min Max Unit 4.75 2.0 5.25 V V V mA mA mA % % °C 0.8 -18 -1.0 20 40 -55 40 +125 .100 PCA EPA424-25 D.C. .24 .200 Max. .155 .060 .275 .150 Suggested Solder Pad Layout .50 *These two values are inter-dependent. .500 Max. .004 Typ. .235 Max. Input Pulse Test Conditions @ 25° C Unit .02 EIN PW TRI PRR VCC DSA424 Pulse Input Voltage Pulse Width % of Total Delay Pulse Rise Time (0.75 - 2.4 Volts) Pulse Repetition Rate @ Td ≤ 200 nS Pulse Repetition Rate @ Td > 200 nS Supply Voltage 3.2 110 2.0 1.0 100 5.0 .050 Volts % nS MHz KHz Volts Rev. A 2/5/96 Unless Otherwise Noted Dimensions in Inches Tolerances: Fractional = ± 1/32 .XX = ± .030 .XXX = ± .010 .228 .244 QAF-CSO1 Rev. B 8/25/94 ELECTRONICS INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 TEL: (818) 892-0761 FAX: (818) 894-5791