FREQUENCY QESM01 SMD 7.0x5.0 Crystal – Ceramic SMD packaged Specification (Rev-D) Electrical Characteristics ......................................................P01 ESR vs. frequency range and Mode of vibration ..................P01 Mechanical Characteristics ...................................................P01 Ordering Information .............................................................P02 Suggested Reflow Soldering profile ......................................P02 Tape Drawing........................................................................P03 Reel Drawing ........................................................................P03 Frequency QESM01 SMD 7.0x5.0 Crystal – Ceramic SMD packaged July 11th, 2006 Specification (rev-D) Electrical Characteristics Electrical Parameters Unit Frequency range MHz Minimum Typical Maximum 7.3728 Test conditions 100 Frequency Tolerance (at 25°C) ± ppm 10 30 50 Refer to Ordering Information ± ppm 10 30 50 Refer to Ordering Information -20/+70 -40/+85 Refer to Ordering Information Temperature Stability Operating Temperature Range °C Storage temperature range °C Shunt capacitance C0 pF Load capacitance pF Drive level µW -40 +85 7.0 10pF ~ 32pF or series 10 100 ± ppm Aging (First Year) 300 5 MΩ Insulator resistance Refer to Ordering Information Ref at 25°C 500 At 100VDC Customized specification upon request ESR vs. frequency range and Mode of vibration Frequency range (MHz) 7.3728 to 8.999 9.0000 to 9.999 10.000 to 19.999 11.000 to 11.999 Mode of vibration Max ESR (Ω) Fund. / AT Fund. / AT Fund. / AT Fund. / AT Frequency range (MHz) 12.000 to 15.999 16.000 to 39.999 40.000 to 83.999 84.000 to 100.00 100 90 80 70 Mode of vibration Max ESR (Ω) Fund. / AT Fund. / AT 3rd / AT 3rd / AT 60 40 70 60 Mechanical Characteristics Marking for QESM06 Manuf code +Temex code (6 digits) Line 2 Frequency in MHz (6digits) Line 1 Top view Suggested pad Mechanical conditions Vibration 10g, 10Hz to 2KHz according to standard CEI 68-2-63 Shocks 100g, 6ms according to standard CEI 68-227 Note 1 : QESM01 is fully RoHS compliant. H = 1.1 mm max 1 TEMEX reserves the right to modify herein specifications and informations at any time when necessary to provide optimum performance and cost. Frequency QESM01 SMD 7.0x5.0 Crystal – Ceramic SMD packaged July 11th, 2006 Specification (rev-D) Ordering Information Part numbering system LQ QESM01 1 50 Package type Vibration mode Frequency tolerance SMD Package QESM01 : SMD ceramic 7.0 x 5.0 1=Fundamental 3=3rd overtone 10=±10ppm 20=±20ppm 30=±30ppm 50=±50ppm 50 00 24.000MHZ Operating temperature range Frequency stability Load Capacitance Nominal Frequency (MHz) D=-40°C F= -30°C H=-20°C J=-10°C L=0°C M=+50°C N=+55°C O=+60°C Q=+70°C T=+85°C 10=±10ppm 20=±20ppm 30=±30ppm 50=±50ppm 00=series 10=10pF 30=30pF Please enter the nominal frequency Please, enter the value of load capacitance Suggested Reflow Soldering Profile 2 TEMEX reserves the right to modify herein specifications and informations at any time when necessary to provide optimum performance and cost. Frequency QESM01 SMD 7.0x5.0 Crystal – Ceramic SMD packaged July 11th, 2006 Specification (rev-D) Tape Drawing Item Code Dimension Tolerance Pitch of components P 8.0 ± 0.1 Pitch of sprocket hole Po 4.0 ± 0.1 Length from hole center to component center P1 2.0 ± 0.1 Width of carrier tape W 16.0 +0.3/-0.1 Width of adhesive tape W0 7.5 ± 0.1 Height of component hole A 8.18 ± 0.1 Width of component hole B 5.56 ± 0.1 Gap of hold down tape and carrier tape W2 1.75 ± 0.1 Diameter of sprocket hole Do ∅ 1.5 ± 0.05 Diameter of feed hole D1 ∅ 1.5 ± 0.25 K 2.16 ± 0.1 Total of tape thickness Reel Drawing Multiple : 1Kpcs per Reel Unit : mm 3 TEMEX reserves the right to modify herein specifications and informations at any time when necessary to provide optimum performance and cost.