MicroCapacitance (MC) SA SIDACtor® Device RoHS ¨ These DO-214AA SAMC SIDACtor devices are intended for applications sensitive to load values. Typically, high speed connections, such as Ethernet, xDSL, and T1/E1, require a lower capacitance. CO values for the MicroCapacitance device are 40% lower than a standard SA part. This SAMC SIDACtor series enables equipment to comply with various regulatory requirements including GR 1089, ITU K.20, K.21, and K.45, IEC 60950, UL 60950, and TIA968-A (formerly known as FCC Part 68). Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts IDRM µAmps IS mAmps IT Amps IH mAmps P0080SAMCL 6 25 4 5 800 2.2 50 P0220SAMCL 15 32 4 5 800 2.2 50 P0300SAMCL 25 40 4 5 800 2.2 50 * “L” in part number indicates RoHS compliance. For non-RoHS compliant device, delete “L” from part number. For surge ratings, see table below. General Notes: • All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range. • IPP is a repetitive surge rating and is guaranteed for the life of the product. • Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. • VDRM is measured at IDRM. • VS is measured at 100 V/µs. • Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. Surge Ratings in Amps Series IPP A 0.2x310 * 2x10 * 8x20 * 0.5x700 ** 2x10 ** 1.2x50 ** 10x160 * 10x160 ** 10x560 * 10x560 ** 5x320 * 9x720 ** 10x360 * 10x1000 * 5x310 * ITSM 10x360 ** 10x1000 ** 10x700 ** 50 / 60 Hz di/dt Amps Amps Amps Amps Amps Amps Amps Amps Amps Amps Amps/µs 20 150 150 90 50 75 75 45 75 20 500 * Current waveform in µs ** Voltage waveform in µs www.littelfuse.com 3-8 © 2006 Littelfuse • Telecom Design Guide MicroCapacitance (MC) SA SIDACtor® Device Thermal Considerations Package Symbol DO-214AA TJ Operating Junction Temperature Range Parameter -40 to +150 Value °C TS Storage Temperature Range -65 to +150 °C 90 °C/W SIDACtor Devices Thermal Resistance: Junction to Ambient RθJA Unit Capacitance Values pF Part Number MIN MAX P0080SAMCL 25 55 P0220SAMCL 25 50 P0300SAMCL 15 35 Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. IPP – Peak Pulse Current – %IPP +I IT IS IH IDRM -V +V VT VDRM VS Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t – Time (µs) -I 14 12 10 IH 8 6 25 ˚C 4 2 IH (TC = 25 ˚C) tr x td Pulse Waveform Ratio of Percent of VS Change – % V-I Characteristics 0 -4 2.0 1.8 1.6 1.4 25 ˚C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 20 40 60 80 100 120 140 160 Case Temperature (TC) – ˚C Junction Temperature (TJ) – ˚C Normalized VS Change versus Junction Temperature Telecom Design Guide • © 2006 Littelfuse Normalized DC Holding Current versus Case Temperature 3-9 www.littelfuse.com